| |
Technical data: |
Tl.-Id.2054297
MODULE - PANEL CUTTER K 34 M
consisting of:
1 REBUILDING GROUP K34MV/1500
with:
- input module
- hydr. height adjustment of upper rollers
- mech. pressure reinforcing of upper rollers
- hydr. device complete, incl. manual
adjustable hydraulic pump for feed drive
of all oil motors, max. conveying quantity
37 l/min. (it is a feed speed F=0-60 m/min)
with flanged hydraulic pump for servo-hydraulic
pump drive motor 5,5 kW, 400 V, 50 cyc.
- protection hood (full-covering) with safety
locking, folding, with both-sided eye sights,
covered with noise insulation mats
(for total machine)
- without non-return finger device,
intended for installation in a machine line
(possibly additional safety measures in
return area has to be provided by the customer)
1 ADDITIONAL CHARGE
for height adjustment of upper roller through PC
incl. measuring system and control
1 ADDITIONAL CHARGE
for regulation of feed speed through PC
6-12 V DC
1 OUTPUT MODULE K34MV
for installation behind the last sawing module, with:
- 3 lower rollers, non-driven, steel,
wrapped with cord and chromed
1 BRUSH ROLLER TOP
1 EXTRACTION TOP
1 LIFT AUTOMATIC
for upper brush roller
1 BRUSH ROLLER BOTTOM K34M/150
1 EXTRACTION BOTTOM K34G/1500
2 SAWING MODULES K34MV/1500
with:
- basic frame, which can be added
- support guide, chromed
- tooth rack
- 2 lower rollers, non-driven
- 3 upper rollers, with PU-covering,
therefrom 2 pc. driven through oil motor,
via duplex-chain
- lower suction funnel over the total opening width
connection diameter 200 mm
- extraction connections only possibly from drive side
2 EXTRACTION-/DOWNHOLDING DEVICE
for concentrate chip collection via tools,
over the total opening width, adjustable with
the upper roller
connection diameter 2 x 160 mm, with rubberized
pressing rollers 63 mm diameter
2 SUPPORTS RIGHTHAND K34MV
2 SUPPORTS LEFTHAND K34MV
for supporting of 1 sawing- or hogging motor
as well as 1 prescoring motor with:
- guiding mechanic with needle bearings
- pneumatic clamping cylinder for fixing of supports
- separated sawing table with layer compressed wood panels
front half can be removed for tool changing, with
integrated chip control equipment
- pivoting motor base, manual adjustable in height, for
sawing- or hogging motor or manual for prescoring motor
- 24 V direct current positioning motor with worm gear
i=2:80 with downstream transmission 1:2,
adjusting speed F=70 mm/s
- magnetical length-measuring system
- energy chain
-(without motors)
1 CIRCULAR SAW MOTOR 5/10 kW
1 CIRCULAR SAW MOTOR 5/10 kW
1 CIRCULAR SAW MOTOR 1,8/3,7 kW
1 CIRCULAR SAW MOTOR 1,8/3,7 kW
4 TOOL FITTINGS / MOTOR PROTECTION
for dividing saw-/hogging motor
2 CIRCULAR SAW MOTOR 1,5 kW, 12000/18000 IPM
2 CIRCULAR SAW MOTOR 1,5 kW, 12000/18000 IPM
4 TOOL FITTINGS / MOTOR PROTECTION
for prescoring motor
1 ELECTR. DEVICE K34MV
1 FREQUENCY CONVERTER 22 kW / 55 A
for 2 hogging motors
2 FREQUENCY CONVERTERS 4,0 kW 7,0 KVA
(for dividing saw motors)
1 FREQUENCY CONVERTER 4,0 kW 7,0 KVA
(for 2 hogging-prescoring saws)
2 FREQUENCY CONVERTERS 4,0 KVA 2,2 kW
(for 2 dividing saw - prescoring saws)
1 PC-CONTROL K34M 4 SUPPORTS
1 SOFTWARE K34M 4 SUPPORTS
weight 6350 kgs
|
|
