Hot water tank

Condition: used, Year of construction: 2010, machine/vehicle number: 1000017741, inner dimension length: 1,000 mm, inner dimension width: 840 mm, inner dimension height: 815 mm, operating temperature: 1,700 °C, usable tank capacity: 685 l, No minimum price – guaranteed sale to the highest bidder! The machine was professionally dismantled and stored. All parts and connections are labeled for reassembly. An on-site inspection is possible at any time. TECHNICAL DETAILS Furnace chamber and usable space Usable batch space (W × H × L): 840 × 815 × 1,000 mm Total length of the graphite box: approx. 1,100 mm Usable volume: approx. 685 l Operating temperature: max. 1,700 °C Operating temperature under partial pressure: max. 1,500 °C Operating temperature under vacuum: max. 1,700 °C Temperature uniformity: ± 10 K Temperature fluctuation in the steady state: ± 5 K MACHINE DETAILS Process pressure range: 1 × 10⁻² < p < 1,040 mbar Final pressure in the empty, clean, and cold furnace: < 1 × 10⁻² mbar Leak rate: < 5 × 10⁻³ mbar·l/s Power supply: 3 × 400 V, 50 Hz Permissible voltage fluctuation: max. ± 5 % Installed heating power: max. approx. 190 kW Electrical power of the pump station: approx. 14 kW Cooling water flow rate: approx. 150 l/min Cooling water temperature: 20–30 °C Lasdpjz I Tt Ijfx Ahash Cooling water pressure: 2–4 bar Cooling water quality requirements: according to specification PW 800 943 ND Compressed air for valve operation: 4–5 bar Nitrogen inlet pressure: 5–7 bar Hydrogen inlet pressure: 5–7 bar EQUIPMENT Double-walled furnace chamber made of stainless steel with water cooling Internal graphite box for precise guidance of the process gases Post-cleaned graphite components Automatic control of the entire process Pump station Labeled lines and connections for easier recommissioning Note: Two internal graphite heating elements were damaged during dismantling and must be replaced.

Year of construction: 2014, condition: ready for operation (used), An industrial Pyreg pyrolysis plant for the thermochemical utilization of biogenic residual materials is available. Fuel capacity: 500kW/module, max. fuel throughput capacity per module: 1375kg/year, min. fuel lower heating value on dry basis: 10MJ/kg, max. fuel moisture content: 50%, biochar production: 40kg/h, thermal heat output (exhaust gas heat): 150kW, power consumption: approx. 7.5kW. Plant dimensions X/Y/Z: approx. 9000mm/3000mm/3000mm, weight: approx. 10000kg, control system: PLC. Documentation available. An on-site inspection is possible. Lasdpfxox Sywgj Ahaoh

Condition: ready for operation (used), Year of construction: 2018, operating hours: 13,270 h, laser type: fiber laser, laser power: 4,000 W, sheet thickness (max.): 20 mm, overall weight: 9,700 kg, year of last overhaul: 2025, The system must be dismantled between November 20, 2026, and November 22, 2026! TECHNICAL DETAILS Laser type: Fiber laser Laser power: 4,000 W Sheet metal thickness (max.): 20 mm Sheet metal thickness steel (max.): 20 mm Sheet metal thickness stainless steel (max.): 20 mm Sheet metal thickness aluminum (max.): 20 mm MACHINE DETAILS Control type: CNC control Automation level: Automatic Actuation type: Electric Power: 4 kW (5.44 hp) Input voltage: 400 V Input frequency: 50 Hz Type of cooling: Water Compressed air connection: 7 bar Laser operating hours: 13,270 h Laodpfx Aoz I S Uwshaeh Year of last overhaul: 2025 Dimensions & Weight Dimensions (L x W x H): 9,310 x 7,813 x 2,300 mm Total weight: 9,700 kg EQUIPMENT CE marking Central lubrication system Cooling unit Documentation/Manual Dust extraction Emergency stop switch Fume extraction Safety light curtain

Condition: excellent (used), Year of construction: 2021, operating hours: 4,689 h, functionality: fully functional, machine/vehicle number: 103, overall weight: 32,000 kg, power: 390 kW (530.25 HP), conveyor belt speed: 2,000 mm/s, fuel tank capacity: 950 l, The machine is equipped with a new roller! The following work was carried out on the machine: Machine washed and cleaned Roller disassembled and bearing shield separated from the roller Rack, limiter, and comb attachments disassembled Cooling and air intake system, front door, and soundproofing register disassembled and reassembled Roofs disassembled and reassembled Various brackets repaired and re-welded Oil pan replaced Exhaust system completed Openings in the housing retrofitted with labyrinth sealing New tools mounted on the drum and rack Roller mounted Cable harnesses repaired TECHNICAL DETAILS Type: Size L-C3 VARIOMAT Roller teeth: 42 pieces Limiter: Size L, 20 pieces Roller: New Loading height: 3,307 mm Loading protection: On both sides Laodpfx Aez Rqcmohaoh Longitudinal belt length: 4,450 mm Longitudinal belt width: 1,000 mm Rear belt length: 8,500 mm Rear belt width: 1,200 mm Discharge height: 5,050 mm Conveyor speed: 2 m/s MACHINE DETAILS Engine type: Diesel-hydraulic Engine: MTU 6R1300 Rated power: 390 kW Engine speed: 1,700 rpm Emission standard: EU Stage V Fuel tank: 950 l Additional hydraulic connection: 30 l/min Additional hydraulic connection: 70 l/min Roller drive: 380 kW Drive system: VARIO Hydraulic system: Load-Sensing system Operating hours: 4,689 h Chassis: 3-axle semi-trailer chassis unit Drive: Hydraulic Dimensions & Weight Dimensions in working position (L x W x H): 16,786 x 2,500 x 5,050 mm Dimensions in transport (L x W x H): 9,971 x 2,500 x 3,893 mm Total weight: 32,000 kg Operating hours: 4,689 h EQUIPMENT Basic package Inventhor Type 9 Additional hydraulic connection 30 l/min and 70 l/min Roller drive via planetary gear 380 kW Load-Sensing system Radio remote control, complete Large side GRP maintenance doors easy-to-maintain engine compartment with LED light hydraulically reversible fan wheel loading protection on both sides Fire extinguisher Maintenance ladder Toolbox acoustic start-up warning Doppstadt telematics system 3-axle semi-trailer chassis unit Shredding system Size "L-C3"-VARIOMAT Size "L" - "Limiter" (20 pieces) hydraulic drive Watering on both sides Rear belt 8.5 m, 1,200 mm wide Overbelt magnet neodymium Frame for overbelt magnet neodymium Central lubrication with pump LED lighting package engine compartment and rear Note: The Doppbasket system can be retrofitted for an additional cost.

Year of construction: 2014, condition: ready for operation (used), Clamping force: 1600kN, weight: 9t, operational hours counter: 3638h, with Handling Robot ENGEL viper 20. Lsdpfx Aoh Nypfshaeah

Condition: ready for operation (used), functionality: fully functional, TECHNICAL DETAILS Drive power: 15 kW EQUIPMENT Control system Suitable for secondary shredding The seller has a suitable conveyor belt in stock as an optional extra. Ljdpfx Ahjz Ngbveasah

Condition: ready for operation (used), functionality: fully functional, screw diameter: 200 mm, Granulation of temperature- and shear-sensitive plastics Suitable for soft PVC Suitable for rigid PVC Suitable for HFFR formulations Suitable for elastomer compounds for low-, medium-, and high-voltage cables TECHNICAL DETAILS Screw diameter: 200 mm Lasdpfx Aez Ngaxshaoh Length from feed inlet to end: approx. 1,100 mm L/D ratio: approx. 5.5 : 1 MACHINE DETAILS Drive power: 72.5 kW Overall machine length: approx. 2,500 mm Feed inlet height: approx. 1,000 mm EQUIPMENT Eccentric granulation EGR Degassing zone Can be used as a single-screw extruder for various processing applications

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, input voltage: 400 V, travel distance X-axis: 3,220 mm, travel distance Y-axis: 800 mm, travel distance Z-axis: 600 mm, number of slots in tool magazine: 55, total height: 3,600 mm, total length: 7,500 mm, total width: 4,200 mm, overall weight: 15,500 kg, table length: 3,900 mm, table width: 750 mm, controller model: Heidenhain, distance table center to spindle nose: 720 mm, spindle motor power: 35 W, rapid traverse Z-axis: 40 m/min, rapid traverse X-axis: 40 m/min, rapid traverse Y-axis: 40 m/min, spindle speed (max.): 18,000 rpm, spindle speed (min.): 30 rpm, table load: 3,500 kg, tool diameter: 80 mm, tool length: 330 mm, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Vertical machining center with traveling column "HEDELIUS mod. CB80 MAGNUM" with Heidenhain TNC-530 Laedpfx Aev Sdc Ushajh

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Load capacity: 2,500 kg Lifting height: 6,430 mm Mast type: Triplex mast Full free lift: available Fork length: 1,200 mm Hydraulic functions: 3rd valve and 4th valve Side shifter: available Hydraulically adjustable forks: available MACHINE DETAILS Manufacturer: Linde Type: E25 Laodpfoz R Tpkjx Ahaeh Year of manufacture: 2019 Drive type: Electric Battery type: Lithium-ion Battery year of manufacture: Battery voltage: 90 V Battery capacity: 268 Ah Measured idle voltage: 97.4 V Operating hours: 12,011 h Own weight: 5,200 kg Overall length: 3,700 mm Overall width: 1,200 mm Overall height: 2,824 mm Service valid until: UVV (Technical Inspection Association) valid until: EQUIPMENT EVO facelift model Former Linde full-service unit Hydraulic double pallet clamp Full cabin Heater Windshield wiper White, non-marking tires LED work light front LED work light rear Road traffic lighting with turn signals Orange warning light Safety Light front Safety Light rear Front camera Comfort seat All dimensions are approximate. No warranty is given for typing or measurement errors. Collection conditions: Side loading up to 6 tons with a large forklift on site is possible. Loading is at your own risk. Rear loading via ramp possible with a truck height of 100–150 cm, up to 15 tons and up to a width of 230 cm. Collection is only possible after receipt of payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. If the machine is not collected on time, a storage fee of €20 per machine and day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 639

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Electrical data Battery voltage: 80 V Charging current: 140 A Suitable battery capacity: 800–1,000 Ah Mains connection: 400 V / 16 A Battery connection: REMA 320 A MACHINE DETAILS Manufacturer: TCE Type: 80 V 140 A Year of manufacture: 2026 Lasdoz R Sg Iopfx Ahaoh Condition: New and unused, in original packaging Length: 600 mm Width: 600 mm Height: 600 mm Weight: 70 kg EQUIPMENT 400 V / 16 A mains connection REMA 320 A plug All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: Side loading up to 6 tons with a large forklift truck available on site is possible. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons, and up to a width of 230 cm. Collection is only possible after receipt of payment confirmation by email. Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. In the event of delayed collection, a storage fee of €20 per machine per day will be charged. Outstanding storage fees must be paid in full before collection. Lot number: 8040

Condition: like new (used), Year of construction: 2022, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 700 mm, total height: 2,800 mm, total length: 1,350 mm, total width: 1,260 mm, workpiece weight (max.): 300 kg, table width: 450 mm, overall weight: 2,300 kg, type of input current: three-phase, table length: 888 mm, drilling depth: 500 mm, Technical equipment -4-way guide changer -32-way electrode changer -Preparation for rotary swivel axis -High quality of drive axes and guides -Integrated compressor cooling units for electronics and external connection option for dielectric cooling -High erosion performance thanks to MOSET generator -Fine filter for working with small pipe diameters Laodpfx Ahsvppw Seajh EROSIX CONTROL -Fast probing -Simple programming for complex 5-axis machining -Extensive measuring cycles -Program transfer and storage via TCP/IP interface -High operating comfort

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Charging voltage: 80 V Charging current: 120 A Ledoz R Sgujpfx Ahajah Suitable battery capacity: 600–900 Ah MACHINE DETAILS Year of manufacture: 2026 Mains connection: 400 V / 16 A Dimensions (L × W × H): 600 × 600 × 600 mm Weight: 70 kg EQUIPMENT Rema connector: 320 A Original packaging All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: * Side loading up to 6 tonnes is possible with a large forklift truck on site. Loading is at your own risk. * Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tonnes and up to a width of 230 cm. * Collection is only possible after receipt of the payment confirmation by email. * Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. * In case of delayed collection, a storage fee of €20 per machine and day will be charged. Any outstanding storage fees must be paid in full before collection. Lot number: 8020

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Battery voltage: 80 V Charging current: 100 A Suitable battery capacity: 500–700 Ah Mains connection: 400 V / 16 A Battery connector: REMA 160 A Lodsz R Sgnepfx Ahasah MACHINE DETAILS Manufacturer: TCE Type: 80 V 100 A Year of manufacture: 2026 Condition: New and unused Dimensions (L × W × H): 600 × 600 × 600 mm Weight: 70 kg EQUIPMENT Original packaging 400 V, 16 A mains plug REMA 160 A battery connector All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: * Side loading up to 6 t is possible with a large forklift on site. Loading is done at your own risk. * Rear loading via ramp is possible for truck heights of 100–150 cm, up to 15 t, and up to a width of 230 cm. * Collection is only possible after receipt of the payment confirmation by email. * Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. * A storage fee of €20 per machine per day will be charged for late collection. Outstanding storage fees must be paid in full before collection. Lot number: 8011

Condition: used, Table unit from a DROOP & REIN portal milling machine Clamping plate with T-slots made of cast steel gray cast iron Table unit with clamping plate and very solid guideway Table clamping surface 5500 x 2000 mm Travel of the table clamping plate approx. 3100 mm Table height 1050 mm Table load: max. 20 tons Ball screw: Ø 100 mm Thread pitch: 20 mm (single-start) - Processing table guided very stably on the bed - Metal telescopic guideway cover - comes from a DROOP & REIN portal milling machine Lasdpfx Ahsthuzpsajh - Longitudinal table movement via ball screw and SIEMENS servo motor - Clamping surface with 11 T-slots 28 mm - Drive via SIEMENS 1FT6134-6AB71-1AG2 servo motor with IC200448S/R encoder (RN 000 B25) Total length 9500 mm Width 2000 mm Overall height 1050 mm dead weight 28 ton. good condition

Condition: ready for operation (used), functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Output voltage: 48 V Charging current: 50 A Suitable battery capacity: 300–500 Ah Maximum battery capacity: 800 Ah (?) Protection class: IP66 Mains connection: 220 V Connector type, battery side: Rema, 160 A Impact protection: available MACHINE DETAILS Year of manufacture: 2026 Overall length: 300 mm Overall width: 200 mm Overall height: 200 mm Weight: 10 kg EQUIPMENT 220 V mains plug Rema connector, 160 A All dimensions are approximate values. No guarantee is given for typographical or measurement errors. Collection conditions: Lsdpoz R Sf Rsfx Ahasah * Side loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. * Rear loading via ramp is possible for truck heights of 100–150 cm, up to 15 tons, and up to a width of 230 cm. * Collection is only possible after receipt of payment confirmation by email. * Collection without prior notification is possible from Monday to Friday between 07:00 and 16:00. * If collection is not carried out within the specified timeframe, a storage fee of €20 per machine per day will be charged. Any outstanding storage fees must be paid in full before collection. Lot number: 4850