Orbital stretch winder

Spinner 1800s

Year of construction: 2019, condition: new,

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood Hsdpsv Si Szofx Aiksnp 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Year of construction: 2026, condition: new, Fully automatic horizontal stretchfilmwraping machine with air bubble film unit SPINNER 1500s + BN Application: Packaging, grouping and protection of long or bulky products like furniture, doors, timber boards, etc. operator side: - in throughput direction right General machine features: - Main motor power: 2,2 kW - Max. ring rotation speed: 50 rpm - Min. ring rotation speed: 10 rpm - Electronic control components: Siemens , Schneider, LS - Total weight: 1600 kg Standard Equipments; - Driven conveyors belt (infeed and outfeed) for automatic product feeding - Adjustable ring rotation speed - Adjustable stretchfilm tension with mechanical brake device - Automatic stretchfilm clamp and cutter system - Automatic stretchfilm hooking system - Pneumatic front and back top presses to hold the product while wrapping - Photocell to start automatically the wrapping cycle - Touch screen to adjust machine parameters to the product needs - Operator safety systems Optional Equipments; - Different sized conveyors - Infeed and outfeed rollers - Air bubble film unit. (INCLUDED FOR THIS OFFER) Technical features: Product to Wrap Sizes - Max. length: Unlimited - Min. length (wxhxl): 100x18x550 mm Conveyor belt’s features: - Useful length: 1924mm - Total length: 2000mm - Working height: 900mm - Electric motor power: 0,75 kW - Max. speed: 10 m/sec. - Max. Load Capacity: 150kg/ m Stretchfilm features: Hnedpofuwrcjfx Aikjp - Max. width: 250mm - Max. diameter: 230mm - Reel core diameter: 76mm - Recommended thickness: 23, 30, 35 micron Air bubble film unit: - Max. film width: 1350mm - Max. film reel diameter: 700mm - Reel core diameter: 20~76mm - Suitable film materials: PW film, PE air bubble film, PVC film - Cutting & welding system operating temperature: 50°C~150°C

Condition: new, Type SK-1000-P6 Working width 1000 mm Min.working length 500 mm Working thickness 2-150mm Polishing roller speed - Frequency control Feeding speed 3-12,5 m/min Total motor power 13.87 kW Disc motor 1.5 kW*1 Cross motor 1.5 kW *1 Screw roller motor 2.2 kW *2 Feeding power 2.2 kW Up and down motor 0.37kW*4 Hsdpfx Aiodmi Niskjnp Swing motor 0.37kW *2 Working table up and down 0.55 kW Transport dimensions 3650x1850x2100mm Weight 4200 kg

Condition: new, functionality: fully functional, input voltage: 230 V, Cobot palletising solution - Relieves employees from heavy lifting and monotonous physical strain - System can be configured and adapted to individual requirements - Requires less floor space than conventional palletising solutions (dimensions: 2,650 x 1,600 mm) - No stationary safety technology required, making UNIPAL easy and flexible to use - Dashboard for process overview - Up to 22 kg payload and 2,200 mm palletising height - Fast and easy retooling - Plug-and-play (requires 230 V mains supply) and 6 bar compressed air Hsdpjrbz Rxjfx Aikjnp

Condition: ready for operation (used), Year of construction: 2023, Load capacity: 1450/1125kg, load center: 600mm, lift height: 3200/4900mm, battery weight: 300-350kg, free lift: 900mm, mast height lowered: 2100mm, mast height extended: 4900mm, reach: 590mm, ground clearance under mast: 80mm, ground clearance at axle center: 50mm, track width: 1292mm, frame cross-section: 1058mm, front overhang: 655mm, wheelbase: 1120mm, rear overhang: 175mm, side shift: 80mm left / 80mm right, lost load thickness: 880mm, fork tilt back: 3°, fork tilt forward: 3°, min. turning radius: 1350mm, support arm height: 282mm, support arm length: 530mm, maximum speed: 6km/h, gradeability: 5%, battery capacity: 24V/270Ah, fork dimensions: 35x100x1070mm, front wheels (polyurethane): OD 200mm / width 50mm, rear wheel (solid rubber): outer diameter 250mm / width 75mm, AC drive motor: 24V / 2.5kW, AC pump motor: 24V / 5kW, rated power: 2.5kW, width: 1512mm, length: 1950mm, net weight without / with battery: 2800/3150kg, operating hours: 86h. An on-site inspection is possible. Hnjdpfew S Tyaox Aikjp

Condition: new, Year of construction: 2024, functionality: fully functional, load capacity: 5,000 kg, Column lift turning device 5000 kg, 3000, 1000 load capacity Positioner Sideros Syncrolift Double column Hjdpfx Asuk Niyoikonp Radio remote control (wireless) Year of construction 2024 Load capacity 5000 kg Minimum working height: 1100 mm Maximum working height 1600 mm Speed 0.5 rpm Vertical adjustment 500 mm Clamping plate diameter 1000 mm Rotation 2.2 kW Lifting motor 2 x 2.2 kW Various column lifting and turning devices are available: 500 kg, 1000 kg, 2000 kg, 3000 kg, 5000 kg, 10000 kg, 20000 kg Request a quote

Year of construction: 2009, condition: good (used), - Fully automatic - Package height max. (mm): 650 - Package height min. (mm) :15 - Package width max. (mm): 1250 - Package length min. (mm): 300 - infeed conveyor (mm): approx. 2.000 x 1.300 x 900 - Outfeed conveyor (mm): approx. 2.000 x 1.300 x 900 Hedspu Anmepfx Aiksnp - Outfeed table - Overall dimensions (mm): approx. 8,000 x 3,000 x 2,200 - Total connected load (kW): approx. 5

Condition: new, Year of construction: 2025, Suction nozzle diameter: 1 x 200, 3 x 100 mm Nominal air flow rate: 1760 m³/h Residual dust content: 0.1 mg/m³ Chip collection volume: 240 l Filter cleaning: motorized Motor power: 3 kW Noise level: 78 dB(A) Machine length: 1340 mm Machine width: 900 mm Machine height: 2170 mm Weight: 178 kg Hnsdpfx Aiohpmawokep

Condition: new, Year of construction: 2026, The ATC series of plotters has been developed for professional use in large industrial plants and factories for the production of complex large-size components. Thanks to its special design, the machine is adapted to the production of casting models and yachts, among others, significantly reducing processing times. ATC machines use an additional reinforced structure and stronger AC servo drives on each axis. The presence of five axes provides support in the machining process of even the most demanding elements. The plotters in this series come standard with automatic tool change, a six-position linear magazine and a tool height sensor. The applied solutions significantly accelerate the machining process requiring the use of several milling cutters. Processed materials: -wood - wood-based materials (chipboard, MDF, OSB, etc.) -plastics -Composites -PVC - non-ferrous metals (aluminum, brass, copper, etc.) Hnodpeiq U Tqjfx Aikjp CONSTRUCTION: The plotter is made entirely of high quality steel. During the production process, all elements undergo a special heat treatment. WORK AREA: The usable area of our machine tool is 3000 x 6000 [mm] AXIS RANGE AND GATE CLEARANCE: Customised parameters DRIVES: Our machine tools were powered by digital motors with high resolution and high power, which ensures appropriate acceleration and speed in particular directions. Classic and proven helical blades work in the X and Y axes, which ensure high durability and precision, and the Z axis is driven by a high-quality ball screw. All axes run on rail guides. SPINDLE: TOOL MAGAZINE: The standard equipment of the machine is a linear tool magazine equipped with 6 HSK cones. Additional tool magazine positions can be provided. SOFTWARE: The machine is equipped with appropriate CAD / CAM software in the latest version. The software enables quick and easy design of elements, which the program then converts into the so-called G-code. It is also possible to import finished files from other programs. CONTROL: The machine is operated by the controller, which has its own processor and operating memory, which ensures stable and reliable operation. The machine controller has the function of active vector analysis, thanks to which the operation of the device is smooth and the error in processing is small. The controller has the function of returning to further work after the loss of power, so there is no need to initialize the program from a scratch. The memory built into the controller allows the machine to work without having to load the program each time.