Automatic cross strapping machine

SMB N3K / Ampag 40K

Condition: refurbished (used), FULL LINE of Drilling, max working width mm 3200, with fast automatic handling equipment. Composed of the following machines: A) LOADER (Portal) "RBO" Winner C 3200 with double pick-up and central motorized rollers table. With 2 on-ground motorized rollers ways to in-feed the piles (stacks) of panels to loader. B) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° C) 1st Auotmatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units Ppjdpfx Abedfgg Ij Ujp D) 2nd Automatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units E) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° G) UNLOADER-STACKER (Portal) "RBO" Winner SC 3200 with double pick-up, with double storage station, with central motorized rollers table. With 2 on-ground motorized rollers ways to out-feed the piles (stacks) of panels from the Unloader

Year of construction: 2011, condition: used, functionality: fully functional, Finger jointing line for cross sections up to 200 cm² (80/240 mm or 100/200 mm), with the following. components: 1. HOWIAL tilt unstacking - SH/4t - 1,75x1,75x6,00m - 4t - short. Length 2,50 m, semi-automatic separation of the package. For tilting the wood pile up to 45°. Electric motor drive. stack dim. max. 1,75 x 1,75 x 6,00 m max. stacking load 4 t shortest wood length 2,5 m 2. HOWIAL - VE 1 lamella separator for crosscut saw. With pneum. controlled tongues, on which the material is marked for defects, deposited on the roller conveyor below. 3. HOWIAL - evaluation roller conveyor RO-1 digital wood moisture measuring, control and recording system for autom. recording and control of wood moisture in cycle measuring method according to electric resistance principle. 4. gann DMT-8 dig. Wood moisture measuring, control and recording system for automatic detection and control of wood moisture in the cycle measuring method according to the electrical resistance principle. Plant in large switchboard complete with ink jet printer. 5. HOWIAL - crosscut saw AS-30 B pneum. Under table crosscut, with 2 autom. feed units, autom. crosscut. Special photocell control for detection of fluorescent line markings. Automatic waste disposal possible. Saw motor power 7,5 kW saw blade diameter 700 mm feed drive approx. 2 x 1,5 kW Air pressure 8 bar feed speed max. approx. 60 m/min. 6. HOWIAL - conveyor belt cut off waste, with studded belt and guide plates belt width 350 mm belt 2000 mm long belt speed 0,4 m/sec. 7. HOWIAL - double roller conveyor RO-2 6,00 m long incl. transversal transport, drive by round belt, all rollers driven. Cross transport chain conveyor. Ejection ± moisture right Transport speed adjustable 100 m/min. length approx. 6,00 m Width of rollers approx. 400 mm Diameter 112 mm 8. compact finger jointing machine Cook Bolinder The technical data are original from Cook Bolinder: wood width from 75 to 245 mm Timber thickness from 20 to 105 mm Input lengths from 1m to 6 m Cross sections from 30 cm² to 200 cm² Pressing force 5 - 22 to Spindle diameter 50 mm tine profile 15/15 spindle speed approx. 6000 upm Total electrical connected load approx. 62 kW Machine weight approx. 9 to. Gluing OEST comb system for PU Modern Telemechanique SPS control. 9. HOWIAL - Roller conveyor with destacking system Driven roller conveyor with autom. ejector and hydr. driven destacking arms. Technical data: H: 920 mm L: approx. 12.000 mm Pjdpfei Ezx Djx Ab Uspp 10. safety fences incl. circuit breaker 11. finger joint testing machine BSPLT-100 Testing machine for finger joint bending test according to DIN 1052-1/A1 and EN 385 Support distances freely adjustable, attached dimension scale, autom. calculation of support distances in the software. Fully automatic test procedure by mouse click on PC (not included). Alternatively, the test procedure can be started by key operation on the front panel. Connection of any commercially available PC or laptop (Win 2000/XP) via the supplied RS232 serial cable. Fully automatic measured value logging as well as automatic logging in MS-Excel with graphical display. Representation max. wood width: 300 mm max. wood thickness: 140 mm max. compression force: < 100 kN max. support length: 2100 mm Measuring accuracy WITHOUT DISMANTLING

Condition: good (used), Year of construction: 1994, 2 side planer top - bottom constant table ( always same infeed height ) max. planing width 600 mm max. planing height 280 mm Podpfx Abjhuthyo Uspp planing shafts with strip knives immediately ready for use

Year of construction: 2013, condition: ready for operation (used), Connected load: 4kW, weight: 1t. Pjdohlp Efepfx Ab Uepp

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m Podpevbtpjfx Ab Uspp -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm

Year of construction: 1993, condition: good (used), functionality: fully functional, machine/vehicle number: RH 241-1-50-30v, used REIFENHÄUSER single-screw extruder with screw size : diameter 50 mm x 33v grooved feed zone and degassing zone type RH 241-1-50-30v with DC-drive 30,2 kW year 1993 Pjdpfspy Eygjx Ab Ujpp with installed switch cabinet Fully functional You are welcome to view this (and other) extruders at our warehouse in Königswinter The machine can be switched on and demonstrated when empty. The screw has been removed and cleaned.

Condition: ready for operation (used), Panel length: 3200mm, panel width: 1000mm, max. workpiece thickness: 38mm, min. infeed length: 500mm. Pjdpfxjm Habdj Ab Uspp

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Vacuum system (with its pump) N. 4 Vertical supporting columns of the top supporting beam N. 1 Horizontal top supporting beam (where the carriage slide on) N. 1 Motorized sliding carriage with horizontal metal arms N. 2 Horizontal metal arms with vacuum cups, adjustables N. 2 Out-side rollers ways (on gound) to in-feed pile of panels to the Loader N. 1 Out-side motorized rollers table (which in-feed the panels to the Unloader), with also cross motorized conveyor belts (at 90°), dimensions mm 7232 (ca.) Separate electric and command panel Electronic Programmer OMRON Perimetral safety metal grids Ppedpfsd Rg Dpsx Ab Usp Working capacity (cycles/min) 16 - 20 (ca.) Min/Max panels thickness mm 10 - 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1200 x 3200 (ca.) Total installed motor power Kw 23.3

Condition: refurbished (used), functionality: fully functional, Extrusion Screen Changers - Continuous Screen Changers Double Piston Filter - - Immediately available, on request also with control, hydraulic unit. Podpfx Aeh Itl Sjb Uepp When making your request, please let us know your desired capacity and the material so that we can offer you the right filter.

Year of construction: 1988, condition: like new (used), Location Kłodawa 66-415 Conditions of delivery Psdpfx Asdx Elmeb Uopp OWN RECEIPT Cost of delivery Customer cover Start type to be agreed Description Comments Four-sided planer, banding machine, Gabbiani spichetting machine Max planing width: 160 mm Max planing height: 100 mm Min. Element length: 180 mm Spindle diameter: 30 mm Number of spindles: 6 Spindle order: down rights, left, Mountain, Mountain bottom Crawler feed: top, bottom Smooth infeed adjustment: 4 - 34 m / min It is possible to work feed at an angle of: 0 ° - 30 ° Feed on cardanach Manual spindle height adjustment Adjustable heads in all directions Automatic lubrication of the track All bearings replaced with Teflon Machine after a full review The machine is adapted to the production of parquet and slats Dust Extractors: 6 x 120 mm Power supply: 400 V Total power: 26.2 kW Dimension of the machine Length: 4060 mm Width: 1500 mm Height: 1200 mm important: planed tables in the whole machine and leveling, setting angles and