Flatbed

Van Hool 3B073 |3 AXLE FLATBED | STACK OF 5 SEMITRAILER...

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Gijdpfx Ajvwlqqeg Tol Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2003, Technical details: pressure: 40 t box opening: 1200 x 730 mm material: Pappe,Plaste - cardboard bottles voltage: 400 / 50 V / Hz total power requirement: 16,4 kW transport measurements machine: 6,5 x 6,2 x 2,7 m Fully automatic hydraulic CHANNEL BALL PRESS for recycling with conveyor unit/conveyor belt LxW: 4500x1000mm motor driven Gisdpfxeu Nw Ezj Ag Tsl with automatic binding unit 3-fold bale count display/counter bale chamber LxWxH: 1800x800x800mm with 1,2m³ volume bale size LxWxH: 800x800x300-1600mm Filling opening LxW: 1200x730mm: Filling height 1200mm Hopper size LxWxH: 1200x1200x1400mm; filling height 2500mm *

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Hours 43.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted Gsdpfxskcgyno Ag Tjil After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Year of construction: 2008, condition: used, Field of application: Freight transport Attachment suited for: Loading and unloading machines Please contact ATS Norway for more information Please provide reference number upon request: 20081 Specifications: 2008 model Weight: 750 kg Hydraulic pump Length: 12 meters Ready for delivery Description:2008 Palfinger PK 14080 C crane with hydraulic pump.The crane was overhauled when the owner purchased it.Ready for delivery. Own weight: 750 Model: PK 14080 C kran m/ hydraulikk pumpe Gijdpfsw Ia Ngjx Ag Tjl

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, Giodjtvau Aopfx Ag Tjl • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, transport height: 2,300 mm, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Drive: 37 kW Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Godpfsxl Rqbex Ag Tsil Transport weight: 27,000 kg Technical specifications conveyor belt: Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Filling option: at floor level

Condition: used, functionality: fully functional, mileage: 182,200 km, fuel type: diesel, color: white, emission class: euro2, Year of construction: 2000, MERCEDES ACTROS 4140 Year 2000 Diesel / Euro 2 Mileage: 182,200 km Manual transmission / Displacement 11,946 cc / 290 kW GVW: 32,000 kg Payload: 16,900 kg / Wheelbase: 4,200 mm Equipment: Gsdpfx Aex Dbryog Teil - Air conditioning Bodywork: - Rear tipper "MINERBA" 5,400 x 2,500 x H 1,400 mm - Approx. 17 m³

Condition: good (used), functionality: fully functional, Used, but fully operational complete line. The video shows the exact machine I am selling. New price starts at 337,605 USD without the upgrades. Please contact me for more details or pictures/videos. Gedpfx Aovn Ei Usg Teil

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Gisdpfeu Thkaox Ag Tol Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2017, operating hours: 13,284 h, functionality: fully functional, pressing force: 140 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,500 kg, oil tank capacity: 2,600 l, Technical data baler: Manufacturer Bollegraaf Type HBC 140 Year of construction 2017 Working hours 13,284, as of October 2025 Press power main press 140 tons (max. 153,5 tons) Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm (l x w) Capacity per cycle time 4,34 cbm Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm (w x h), length adjustable Driving motor 2 x 75 kW Connected load 209 kW Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 850 up to 1.500 kg Hydraulicoil 2.600 l Univis N46 Gisdpoxpxhvefx Ag Tel Baler dimensions with conveyor built up with hopper approx.13,200 x 24,200 x 7,333 mm (l x w x h) Transport dimensions only baler approx.13,200 x 2,884 x 3,539 mm (l x w x h) Machine weight baler approx. 51,810 tons Technical data feeding and elevating conveyor with gooseneck: Manufacturer Bollegraaf Typ HBT 1216/1800 * 23,300 30°/15° Year of construction 2017 Driving motor 7,5 kW Length feeding conveyor 6,750 mm Length elevating conveyor 14,400 mm Length goose neck 2,150 mm Grade 30° Effecting width 1,754 mm Height of side wall feeding conv. 500 mm Height of side wall elevating conv. 800 mm Transport dimensions feeding conveyor with one segment elevating part 9,816 x 2,500 x 2,242 mm (l x w x h) Transport dimensions elevating conveyor with goose neck 13,472 x 2,800 (without motor) x 2,729 mm (l x w x h) Pit dimensions 10,000 x 3,200 x 1,200 mm (l x w x d) Condition: The press is in very good condition and ready for immediate operation, see the function video for more information. The conveyor belt chain needs replacing. The system will be in operation until December 2025. Scope of delivery: baler with conveyor belt, maintenance platform, access ladder, two wire feed stations for 5 wire reels each (without wire), and bale slider. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.