Screw air compressor

ALMIG Variable 90

Year of construction: 2020, condition: ready for operation (used), A Rico compressor system consisting of two Atlas Copco compressors, two refrigerant dryers and an Atlas Copco Beko oil-water separation system is available. Screw compressor Atlas Copco GA 45 VSD+, year of manufacture: 2020, air volume flow: 9.4m³/min, operating pressure: 13bar, motor power: 45kW, motor speed: 4500rpm, machine dimensions X/Y/Z: approx. 1200mm/1100mm/2000mm, weight: approx. 860kg. Screw compressor Atlas Copco GA 45 VSD FF, year of manufacture: 2012, power: 45kW, operating pressure: 18.5bar, speed: 3000rpm. 2x refrigerant air dryers Atlas Copco FX 15, air volume flow: 15m³/min, operating overpressure: 13bar, pressure drop: approx. 0.3bar, refrigerant: R410A, refrigerant charge: 2050g, max. inlet air temperature: 60°C, machine dimensions X/Y/Z: approx. 900mm/750mm/1000mm, weight: approx. 160kg. Compressor management system Atlas Copco Equalizer 4.0/ES6-MK5, control range: 2-6 compressors. Oil-water separation system Beko ÖWAMAT 15, throughput range: 6m³-30m³/min, oil outlet: DN40, container volume: 115.5l, filling volume: 84.3l, oil collection container: 2x10l, max. operating pressure: 16bar, machine dimensions X/Y/Z: approx. 1100mm/550mm/800mm, weight: approx. 40kg. System operating hours: 8656h, controller hours: 42334h. Documentation available. An on-site inspection is possible. Isdpfxsxdc Uvo Abgsia

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES Iiodpfx Ajhzbipebgea THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: new, Straightening press 150 tons with electric motor and additional manual operation by a hand lever pump, especially for fine work. Versions: 30t 60t 100t 150t 200t ᐳ 200 t: on request Special machines: on request New machine! We are also happy to build a customer-specific press for you. High quality hydraulic workshop press with 150 tons maximum pressing force. The press can also be opened and closed in the classic electric mode using a lever. For fine work (e.g. pressing in bearings, straightening, ...) the press also has a hand pump. This allows you to fine-tune the force manually. The printing cylinder is attached to a sliding carriage so that the cylinder can be moved sideways. In this way, you can make optimal use of the maximum stand passage width. Particularities: - 150 tons maximum pressing force - Pressure display with manometer - 2 operating modes: electrical operation or or manual operation - 2 independent hydraulic pumps - Control cabinet with motor protection monitoring and safety devices - adjustable passage height - Pull chains for easy adjustment of the passage height - massive machine frame - cylinder laterally adjustable (mounted on sliding carriage) The press can be tested under power on site. ----- Numerous other workshop presses in different designs, sizes and with optional additional equipment available! 30, 60, 100, 150, 180, 200 tons. Iiodpfof Sqckox Abgsa ----- Please just contact us, we will be happy to advise you without obligation. The stated price is net plus 19% VAT. All statements without guarantee! Europe-wide delivery possible! ----- The European Commission provides a platform for out-of-court online dispute resolution (OS platform). The offer serves exclusively as an internet presentation of our goods. The contract negotiation comes about by means of telecommunication (email, fax, telephone, news portal), where we first make you a non-binding offer, in which we inform you about our general terms and conditions and the right of withdrawal with imprint before the purchase / contract is concluded.

Condition: used, Year of construction: 1998, Overview This machine was built in 1998 by French manufacturer Sidel. The machine is in very good working condition, is already professionally dismantled and stored in a warehouse. Techn. Details Capacity: 7.200 bph in 1,5L Number of moulds:  6 (molds not included) Equipped with quick change for shell molds Number of heating modules: 10 modules Neck personalization: 29/25      Working hours: 47.000 only         Machine was regularily maintained       Machine equipped with:            Sidel preforms elevator to unscrambler Sidel preforms unscrambler & feeder Sidel oven & blowing wheel for 6 molds Sidel electrical cabinet Sidel PCC drive & control panel Big set of spare parts list upon request Iedpfx Aberkgy Uegjia

Year of construction: 2024, condition: new, noris- Extruder MINI ESE 20/25 D Technical data Screw diameter [mm] 20 Screw length [L/D] 25 Screw speed [min-1] 20-200 min -1 Screw axial pressure [bar] 300 Continuous load 350 maximum Drive Three-phase drive with frequency converter Drive power [kW] max. 2.5 Reduction gear with integrated axial bearing Weight [kg] approx. 160 Dimensions [Lx Wx H] [mm] approx. 1050 x 600x 1590 *) Electrical connection values 3 / N / PE Supply voltage [V] 400 at 50 Hz Control voltage [V] 230 Temperature control electrical resistance heating bands in mica design. Isdpfx Abohx Elfsgeia Max. processing temperature [°C] 300 Switch cabinet and control panel The electrical installation of the extruder is located in the machine base. The base contains all the necessary switching, control and display devices. The feed zone is water-cooled, the water connection is provided by the customer, a cooling unit for cooling the water is not included in the offer. Extruder tools are not part of the offer

Condition: good (used), power: 30 kW (40.79 HP), Year of construction: 2010, operating hours: 51,548 h, ambient temperature (min.): 3 °C, ambient temperature (max.): 45 °C, pressure (max.): 8 bar, rotational speed (max.): 2,945 rpm, machine/vehicle number: 100609.1, Equipment: type plate available, The Kaeser ASD 57 is an energy-efficient screw compressor designed for reliable compressed air supply in industrial applications and is characterized by its compact design and quiet operation. With advanced Sigma profile technology and intelligent control, it offers optimum performance and durability. Iijdpfx Abst Iwyusgsa Technical details: Item number: 100609.1 Serial number 1941 Year of manufacture: 2010 Nominal output: approx. 30 kW Maximum operating pressure: 8 bar Engine speed: 2,945 1/min Condition: used (see pictures and type plate)

Condition: excellent (used), functionality: fully functional, Equipment: refrigerant dryer, type plate available, Full container load of second hand electric rotary screw industrial compressors for export. Iiedpetp Tzxofx Abgea Loading of container included.

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: API621725, For sale: Atlas COPCO ZR 132 compressor with filters, 125 KW Iisdpfxewrm T Is Abgja

Condition: used, Year of construction: 2019, machine/vehicle number: LC591, Used complete bottling line for CSD in PET and glass - 8000 bphTechnical Specifications & Performance DataThis complete used bottling line is engineered for beverage production with PET and glass bottles. Optimized for water and carbonated soft drinks, it combines reliable filling, labeling, and end-of-line packaging with robust utilities and process equipment. The line integrates components from reputable manufacturers to deliver consistent quality and uptime in industrial packaging environments.Production speed: up to 8,000 bottles per hourCompatible bottle formats: 0.33L, 0.5L, 0.75L, 1.0L, 1.5L, 2.0LContainers: PET and Glass bottlesMain filler/capper/rinser: Sinkrofill 40/50/10/10, 50 filling heads, 3–5 capping headsBlow molder: Easy Blow 4L (4,200 bph nominal)Labelers: Gernep Rollfed 8-480-1RA (foil/OPP) and Gernep Soluta 10-640 3SK (paper), up to 10,000 bphPack & handle application: SMI LSK 30 T Ergon shrink wrapper, SMI Pack HA-25 SX handle applicatorPallet logistics: Sinkrotech APM-6000-JU palletizer; Atlanta Mytho-A pallet wrapper; auxiliary manual wrapperProcess & utilities: GEA pasteurization station HTF 3000PIN/19; GEA CIP station; Trane Tracer CH535 CGAX/SXAX chiller; Therminus steam boiler (456 kW); Kaeser compressors (CSDX 165 and N 502-G boosters)Inspection & coding: FT System control for volume/cap/label; Hitachi UX printerAdvanced Automation & Control SystemsThe line features modern automation and quality assurance for stable operation and repeatable product quality. A PLC-controlled architecture coordinates rinsing, filling, capping, labeling, and packaging, while inline inspection and coding ensure compliance and traceability.PLC/HMI: PLC installed for centralized control and recipe managementInspection: FT System for volume, cap presence/position, and label verificationElectrical: 400V, 50 Hz, 16A reference (component level)Coding: Hitachi UX inkjet printer for date/lot markingChangeovers: Designed for multiple bottle formats across PET and glassSafety: Standard guarding and emergency-stop circuits across stationsProduction Line Integration CapabilitiesBuilt for flexible beverage production, the line integrates upstream preform handling and blow molding with downstream conveying, labeling, and packaging. Vetromeccanica air conveyors and line conveyors provide smooth bottle transport and accumulation.Upstream: Preform conveyor and hopper, Easy Blow 4L blow molderConveyors: Vetromeccanica Eolo air and line conveyor systemsFormat flexibility: 0.33L to 2.0L across PET and glassEnd-of-line: Shrink packaging, handle application, palletizing, and pallet wrappingUtilities integration: Chiller, steam boiler, compressors, air tanks, water... Iodpfsyhbibox Abgjia

Condition: good (used), Year of construction: 2019, machine/vehicle number: 24451.19, Offer 25359 Technical Data: - Cutting capacity at 90° (round): 250 mm - Cutting capacity at 90° (flat): 275 x 180 mm - Miter adjustment to the left - Cutting capacity at 45° (round): 200 mm - Cutting capacity at 45° (flat): 190 x 180 mm - Cutting capacity at 30° (flat): 130 x 110 mm - Material support height: approx. 920 mm - Saw band dimensions: 3100 x 27 x 0.9 mm - Infinitely variable cutting speed: 15 to 100 m/min - Hydraulic lifting and lowering of the saw frame Iedpfx Abjxup Rfegsia - Upper travel limit of the saw frame - Infinitely adjustable cutting pressure: 0 – 10 m/min - Hydraulic material vice - Micro-spray cooling system - Total drive power: 400 V / 2.2 kW - Required space approx.: W 2400 x H 1600 x D 1800 mm - Weight approx.: 1300 kg - 3 x Roller conveyor, each 1500 mm