Used waste management & recycling equipment for sale (30)

Condition: good (used), Wood shredder for sale Prepared for conveyor belt removal Ideal for shredding wood residues (all types of softwood) and pallets Includes hydraulic pusher Motor: 7.5 kW Rotor width: approx. 82 cm Weight: 1,460 kilograms Full load current: 32 amp Bodpfx Agexbyx Tezjct Main fuse: 35 amp

Condition: new, Year of construction: 2025, Diameter: 160mm Also available in the diameters: 180, 200, 250, 300 mm for an additional charge, other diameters on request. Very stable industrial design. Ideal for separating nails/metal parts from material flows. For example after a wood shredder. including 3 extremely powerful magnets * If desired, up to 6 magnets can be installed in the component - surcharge for each additional magnet + 49 € - Neodymium magnets are also available instead of ferrite for an additional charge Bjdpfx Agjchuvrezsct Your advantages: + Extremely large inspection door with seal for easy stripping of the nails + Stable quick-release fastener +Made in Germany Inspection door / opening: 35x18 cm Installation length may vary

Condition: as good as new (ex-display), Demonstrator with 7 operating hours Another machine available immediately (ex works in Neckartailfingen) MRZ 830 Shredder Custom tariff number: 84659600 Feed opening 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 ph Blades: multi-rotatable Hydraulically operated slide gate Screen perforation of your choice (10 - 40 mm) Weight approx. 1,600 kg Dimensions (L x W x H) approx. 2,290 x 1,420 x 1,750 mm Turbo clutch Included as standard: - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet Bsdpfjv Sqrpex Agzoct - CE compliant . The shredder is designed for shredding natural wood, particle board, and MDF, as well as other materials after testing and approval by the manufacturer. Included: - Raise the shredder by 30 cm (prepared for conveyor belt) Additional shredder options: - Articulated conveyor belt + €8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet + €6,780 net - Conveyor belt and overbelt magnet control + €2,750 net (Start and stop synchronized with the shredder) Raw material requirements: - The moisture content (dry) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Condition: new, Year of construction: 2025, Production time appr. 4 months Our best-selling briquetting press series + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several hundred machines in use with satisfied customers + Good price performance ratio Throughput approx. Up to 200 kg per hour * strongly dependent on the material. - in the last test with aluminum granules smaller than 5 mm - approx. 186 kg per hour + the pressed emulsion. - in the last test with aluminum chips smaller than 18 mm - approx. 120 kg per hour + the pressed emulsion. Technical specifications: Motor: 7.5 KW + 0,55 kW Cooler 400 volts / 50 Hz / 3-phase, Front bush: 125 mm, Briquette stroke max .: 100 mm, Briquette stroke opt .: 80 mm, Pump: 80 liters, Storage container approx. 0.5 qbm content (expandable), Diameter: 1200 mm, with agitator discharge, Hydraulic unit complete with oil tank 220 liters Bodpfx Agjchqxxszsct Dimensions approx. 2095 x 1600 x 1310 mm lxwxh, Weight 1370 kg, Automatic on-off switching via level indicator CE compliant. . Requirements for the raw material: - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of magnetic metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: new, Year of construction: 2025, Another machine immediately available! Briquetting press with PLC control and automatic briquette length adjustment Throughput: up to max. 60 kg/h Briquette: 50 mm cylindrical Motor: 5.5 kW Dimensions: 1,900 x 1,350 x 1,410 mm Weight: approx. 860 kg Requirements: Bcodpov Rpxljfx Agzet Feed material should ideally be shorter than 25 mm chip length Moisture content 6–12% ATRO Machine suitable for intermittent operation. E.g. briquetting for up to 2.5 hours; 1 hour break, etc. If the machine needs to run longer than 2.5 hours continuously, optional cooling must be connected.

Condition: as good as new (ex-display), Year of construction: 2024, Special price: €29,970 net A machine is currently available immediately. The ideal machine for shredding voluminous, light aluminum chips or turnings. Not suitable for more solid aluminum parts. Includes: + Optimized cutting geometry + Adapted slide control + Load-dependent controlled hydraulic slide (which presses the chips against the cutting mechanism) Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Blade: 40x40mm, multi-rotatable, Rotor diameter: 260 mm, Control: Omron PLC, Cutter opening 600 x 800 mm, Funnel volume approx. 0.6 qbm, Hydraulically operated slider Sieve perforation of your choice (15 - 40mm) Suction nozzle Ø 160 mm Bodpfjgmh H Tox Agzoct Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm The following options are available for an additional charge: - Raise the shredder by 30 cm (preparation for conveyor belt) +2,990 € net - Angle conveyor belt (discharge height approx. 220 cm) +9,770 € net - Overband magnet + €6,980 net - Control of conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the chipper) We would be happy to carry out a free test with your material. We invite you to come to us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos.

Condition: as good as new (ex-display), Year of construction: 2024, Special machine for shredding plastics Basic machine from €24,990 net Well suited for shredding: - Paper, cardboard boxes, pipes, profiles, boxes, canisters, buckets, cans, sections of wooden pallets, etc. - Medium-hard thermoplastics such as PVC, PP, PE, PS, PU, PET Includes: - special rotor with embedded blades (reduced load capacity), - small cutting gap between blade and counter blade Motor: 18.5 kW; 400 V - 50 Hz - 3 ph Control: PLC Top cutting unit opening 600 x 800 mm The parts should be a maximum of approx. 500x500 mm in size *the height is less important hydraulically operated slide, sieve hole of your choice (25 - 40mm) For plastics, coarser sieves are recommended (30-40 mm) *If you want to shred more finely, a two-stage shredding process is recommended with downstream granulator type MVZ (sieves 5-15 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm Other options available for an additional charge: - Raise the shredder by approx. 25 cm (Preparation for conveyor belt removal) + €995 net - Angled conveyor belt (discharge height approx. 220 cm) + €8,490 net - Overband magnet + €6,750 net - Control of conveyor belt and overband magnet + €2,495 net (Start and stop synchronized with the chipper) - Alternatively, manual start and stop on the conveyor belt + €497.50 net . Requirements for the raw material: - The moisture content (atro) must be below 25% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear. . We would be happy to carry out a free test with your material. We invite you to come to us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos. --- *only for brittle plastics with a medium degree of hardness, *not for elastic or extremely hard and heavy plastics - this would affect the durability of the system. --- Optional would be the next larger machines Basic machine: Shredder MGZ 830 K-S - 18.5 kW Bsdpsd H R Sxofx Agzect Cutting unit opening at the top 800 x 1,000 mm The parts should be a maximum of approx. 720x700 mm *the height is less relevant from €39,995 net * Options depending on the effort Basic machine: Shredder MGZ 1030 K-S - 22 kW Cutting unit opening at the top 1,000 x 1,000 mm The parts should be a maximum of approx. 900x700 mm *the height is less relevant from €49,975 net * Options depending on the effort Basic machine: Shredder MGZ 1330 K-S - 37 kW Cutting unit opening at the top 1,300 x 1,200 mm The Parts should be a maximum of approx. 1,200x700 mm in size *the height is less relevant from €79,975 net * Options depending on effort

Condition: as good as new (ex-display), Year of construction: 2024, Primary crusher Basic machine starting from € 29,950 net *Options against surcharge Ideal for pre-crushing bulky materials such as pallets, boards, beams, fruit crates, polystyrene, plastics and much more. For the production of wood chips, the primary crusher can also be installed directly above a single-shaft shredder Machine in pre-production * Special options available at extra cost Your advantages: + Volume reduction of up to 70 Bsdpfx Aofd Iciogzoct + Significantly lower transportation costs + Low disposal costs + Production of fuel material + Also ideal upstream of a single-shaft shredder for the production of wood chips Weight: 1,200 kg Dimensions 2050x850x1600 mm Cutting unit opening 1300x700 mm *Optionally also available in 1600x700 mm (motor then 11 kW) (surcharge + 4.995 € net) Throughput: up to 50 pallets/pieces per hour *depending on material Motor: 7.5 kW Options: Industrial top hopper (closed on 3 sides) + € 4,950 net Extra emergency / off button + 495 € net 200 mm extension + 497 € net Requirements for the raw material: - Moisture content less than 30 % ATRO - The machine must be installed in accordance with CE guidelines or secured on site against access from below (into the cutting unit) - Pallets up to a dimension of 1200x800 mm can be processed Longer parts also work on edge

Condition: as good as new (ex-display), Year of construction: 2025, Demo unit with approx. 9 operating hours Another machine available immediately (ex works Neckartailfingen) *Options at extra charge – see below Included: + Profile rotor for higher throughput performance We are happy to provide a free trial with your material. You are invited to visit us in Neckartailfingen for this purpose. Alternatively, you can send your material to us by freight and we will document the test with photos and videos. Motor: 18.5 kW; 400 V - 50 Hz - 3 ph Blades: 15 pieces, multiple re-usable edges Double blade row option: + €995 net Rotor diameter: 260 mm Control system: Siemens S7-1200 PLC Cutting chamber opening: 630 x 820 mm Hopper volume: approx. 0.6 m³ Hydraulically operated ram Screen perforation as required (10–40 mm) Extraction nozzle Ø 160 mm Weight: approx. 1,300 kg Dimensions (LxWxH): approx. 1,737 x 1,167 x 1,650 mm Moisture content: 20% hardwood content) Bsdeb Ny Eyopfx Agzsct - Double blade row + €995 net - Special scraper + €990 net (recommended for shredding veneer, paper, or material thickness

Condition: new, Year of construction: 2025, Little used machine with appr. 275 working hours Your advantages: + extremely large cutting unit opening with 1300x1200mm + special rotor suitable for hardwood and softwood + Energy-efficient and powerful with 37 kW at start-up Technical specifications: Colour: grey / blue Feed opening (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen perforation (mm): 30 - 50 mm - selectable Tools: 37/70 knives Bcsdpfx Asgbkkregzjt Extraction nozzle Ø (mm): 200 mm Dimensions: 2430x2410x1735 mm (lxwxh) Weight (approx. Kg): 3,920 Optional for a surcharge: * to shred veneer or paper (anything thinner than 3 mm) - we recommend a segment floor. The machine in preproduction has not yet installed this. Special option at an additional cost. - 2nd row of knives, for up to 30% more throughput - Fast hydraulics, for increased throughput - Preparation for conveyor belt removal - conveyor belt - HAWK-EYE overbelt magnet --- Optimal pallet size with the option slide extension = 1200x1400 (option slide extension, the cutting unit opening 1300x1700 surcharge + 12,975.00) * is associated with significantly longer production time. * larger machines on request --- Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: new, Year of construction: 2026, Briquetting press NEM 900: production time appr. 5 months for briquetting aluminum chips Throughput: up to maximum 320 kg / h * more details after a free test with heard material . Briquette diameter: Ø 70 mm Optimal briquette length: 70 mm . Technical specifications: Total connection: approx. 31 kW In continuous operation approx. 22 kW 400 volts / 50 Hz / 3 phases Pump: 120 + 60 liters per minute Silo: 1 m³ Silo rollers: 1200 mm Including agitator Oil tank: 600 liters Dimensions: 2500 x 1700 x 1730 mm lxwxh Weight: 2250 kg. Hydraulic pre-compression via slide Main press cylinder Vertical cylinder Above for connecting a cooling unit . One and the source material - max.span: 18 mm Bcjdpjgfm Ryjfx Agzet - Excessive temperature: temperate room at at least + 5 ° C. - max.weight on agitator: 200kg. - The loading must be free of metals and mineral impurities such as sand, stones, etc. This on the pressing tools and / or responsible wear can result

Condition: good (used), Good, used condition Main motor: 11 kW Maximum throughput: 200 kg/h Year of manufacture: 12/2008 / Technically tested: 01/2025 Briquettes: 150x60 mm . *Used machine, purchased as is Functional guarantee upon delivery Bedpfx Aet Hxudogzect

Condition: good (used), Technical data: Briquetting press RUF RB 440 Press capacity when pressing wood: up to a maximum of 440 kg/hour Material moisture: maximum 15 % Bcodpfx Ast H D Ezjgzjt Motor power: approx. 30 kW Briquette size; rectangular: 150 x 60 mm Length: 40 - 110 mm Dimensions approx. 1680 x 1800 x 2000 mm Weight: 3000 kg

Condition: as good as new (ex-display), Year of construction: 2023, Machine for sale at a special price Another machine, available immediately (ex works Neckartailfingen) Demonstration machine with approx. 10 operating hours Your advantages: + Very robust, simple technology + Top price-performance ratio + Suitable for continuous operation + Long-standing, well-functioning / established machine Including control cabinet with timer operation Press is switched on manually and then runs until the time set on the timer (e.g. 4 hours) has elapsed. Then the press switches off. Technical data: Briquette dimensions: approx. 35 x 35 mm (square), Briquette length: 5-40 mm *depending on material Throughput capacity up to 25 kg / h *depending on material Machine dimensions approx. 137 x 75 x 148 cm (length x width x height), Weight of the machine: approx. 250 kg, Capacity of the silo: approx. 250 liters, Motor: 2.2 kW, 400 V - 50 Hz, Noise emission: 62 dB, Raw material requirements: -Wood chips and dust smaller than 15 mm in length -Moisture content less than 18 % ATRO -Sand, stones, metals and minerals increase wear --- Options at extra charge: -Timer function + 490 € net Machine is started manually and switches off automatically after a set time X. Bjdpfxofci D Ao Agzoct -Level indicator for automatic operation + 1450 € net Press starts and then stops automatically * NEW !!! Also available in 230 Volt, Motor then 3 kW instead of 2.2 kW, C7m2mgj Surcharge + 690 € net (delivery time then approx. 8 weeks) ---

Year of construction: 2025, condition: new, *Only the neodymium overbelt magnet is offered, not the conveyor belt underneath. *Neodymium magnets are among the strongest magnets in the world. They have an extreme pulling power and cannot be compared to ferrite magnets. Extremely high degree of separation, depending on the bulk height and the starting material. Bsdsdubpujpfx Agzoct Probably the most compact overband magnet on the market. The competition often uses the less powerful ferrite magnets to save costs. dimensions approx. Length: 104cm Width: 22cm Height: 28 cm (at the motor) *Without controller Surcharge for simple manual start/stop control + 495 € A high-performance industrial neodymium magnet is installed. High-performance neodymium magnet approx. 600x68x36.5 mm * So nails are attracted to a length of 600 mm and thrown off to the side, in the area that is no longer magnetic. This overbelt magnet should be mounted approx. 5 - 9 cm above the material flow. *Assembly/suspension on site Ideal for separating nails from wood chips. Optionally also in a single-shaft shredder that is sucked off Requirements: *Your belt width or useful width inside (of the existing conveyor belt) should ideally be narrower than 55 cm *Suitable for separating nails from material flows that are less than 12 mm high and with a chip length of less than 25 mm. ----- Optional at extra charge: Cross and ascending belt demonstrators from € 7,995 net

Condition: like new (used), functionality: fully functional, Year of construction: 2025, operating hours: 55 h, Machine with special rotor Available immediately Advantages: + Special rotor, with reduced knife protrusion, suitable for both hard and soft materials + 22 kW motor + Efficient square blades *For pallets: up to 10 pallets per hour max. *Depending on screen and material. Significantly higher throughput with smaller wood waste. Motor: 22 kW; 400 V - 50 Hz - 3 ph, Screen: 15/20 mm or as agreed (10 to 40 mm possible) Hydraulically operated pusher Current screen perforation (15/20 mm) *can be changed Extraction nozzle Ø 200 mm Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Sample image above: color of the unit may vary Weight: 1,920 kg Standard equipment included: - Control cabinet with PLC control - Automatic star/delta starter - Fast hydraulic system - Automatic shutdown in rotor idle mode - Speed: 70–90 rpm for high throughput - Cycle control to minimize idle times - Performance-enhancing step control of hydraulic pusher - Pertinax guides for hydraulic pusher - Vibration-damping machine feet - CE compliant The following options are available at extra cost: *Visible in the last 2 images. - Additional blade row + €2,790 - Segmented bottom + €6,890 (recommended for materials with wall thickness less than 3 mm) - Special K-rotor bearing + €3,480 (Recommended for shredding plastics with screens under 15 mm or with a high fine fraction. Not necessary if bearings are lubricated about every 4 weeks of operation) Bcodpsx Af Rdjfx Agzjt - Raise shredder by 30 cm (preparation for conveyor belt) + €2,480 net - Angled conveyor belt (discharge height approx. 220 cm) + €12,980 net - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (Synchronous start-stop with shredder) - Enlarged feed hopper 1500x1500 mm + €3,480 net Raw material requirements: - Moisture content (atro) must be below 25% - The infeed material must be free of metals and mineral impurities. Damage to the tools and/or increased wear may result otherwise.

Condition: new, Year of construction: 2024, Consisting of large bale breaker Type MHB and straw shredder Type MHZ 1) Bale Breaker MHB: Special price from €22,975 net (lead time approx. 15 weeks) Suitable for round or square bales. Includes frequency converter (FU) – regulates the speed of the chain conveyor. The bales are placed on the chain conveyor, and the milling advance is activated. The milling tines tear the straw from the bale and hurl it into the hopper. Ideally, the combination of bale breaker and straw shredder is recommended here. Technical data – Bale Breaker: Performance: 1–2 bales per hour Up to max. 600 kg per hour (depending on screen size used in the straw mill and kW rating of the straw mill). Without straw mill, the bale breaker can process up to max. 900 kg/h straw. Max. square bale size: 2400 x 1200 x 800 mm (L x W x H) Milling motor: 5.5 kW, 380 Volt Chain conveyor feed: 0.75 kW, 380 Volt Dimensions: 3750 x 1730 x 2460 mm (L x W x H) Weight: 400 kg 2) Straw Shredder MHZ 600 – 11/15 kW; available immediately Special price from €6,995 net Surcharge for even larger straw shredder (18.5 kW): + €3,940 net Technical data, MHZ with special hopper: Motor: 15 kW, 380 Volt electric motor Diameter: 600 mm Hardened cutting knives Screen with interchangeable inserts; selectable perforations (10, 12, 15, 22, 30, 45 mm) With star-delta switch, phase protection, and 8 m power cable, plug-in ready Discharge nozzle: 160 mm Blowing distance approx. 12 m Dimensions: approx. 1600 x 1020 x 1360 mm (L x W x H) Weight: approx. 240 kg --- Optional extras for a surcharge: Feed auger: + €970 net Cyclone (suspension by customer on site; should be no more than 10 m away): + €2,970 net Simple filter: €1,750 net --- Bcjdpsb Nulhjfx Agzjt Further options: Industrial extraction system (demonstrator): + from €9,950 net Optional rotary valve (renders material pressureless): + €5,750 net Control panel: from €1,620 net Special breaker extension 3 m (other sizes on request): + €9,750 net Briquetting press MPP 180 S; little used demonstrator 70 mm briquette – up to max. 100 kg/h from €39,700 net * Larger machines available on request --- Description: muetek bale breakers are designed for breaking up round and square bales of hay and straw. The shredder flanged to the bale breaker shreds straw from all types of cereals, hay, maize, and miscanthus. muetek machines of the MHZ / MHB series are characterized by robust construction and heavy-duty build quality. muetek MHB series bale breakers feature a chain conveyor onto which the straw bale can be placed using a front loader. The support surface is adjustable depending on bale type. The chain conveyor pushes the bale against the milling rotor. The feed speed is adjustable. The milling rotor is equipped with several teeth that tear open the straw bale. The separated straw is discharged. --- The machines are generally suitable for dry input material: - Straw - Hay --- Breaking up hemp bales is possible only with a special breaker (surcharge approx. €9,720 net, depending on configuration). Straw mill is not suitable for hemp processing. Requirements for input material: Max. moisture content 12%

Condition: as good as new (ex-display), Year of construction: 2022, Briquetting press for aluminium or steel chips Extremely high pressing force of 3,700 kg/cm² Large storage silo Bjdew Ig Suepfx Agzsct Briquette size: 60 x 40 mm Throughput: Aluminium chips – up to approx. 70 kg/h Steel chips – up to approx. 100 kg/h Brass chips – up to approx. 100 kg/h *depending on feedstock Included: - Emulsion tray - Emulsion pump - Oil cooler

Condition: reconditioned (used), Year of construction: 2023, All wear parts new only 704 operating hours Special price for a low-hour demonstration unit Base machine: €29,990 net Optional extras (for an additional charge): - Cooling unit: €3,995 net Bcedod N Dnhepfx Agzjt - Emulsion tray: €3,990 net The hydraulic briquetting presses of the MPP NEM series compact materials such as aluminum, copper, brass, bronze, graphite, and other non-ferrous metals into dimensionally stable cylindrical briquettes. These machines are distinguished by their robust construction, ensuring consistent briquette quality during continuous operation. The pressing process does not require any binding agents – compaction is achieved solely through hydraulic pressing force. Depending on material, the feedstock volume can be reduced by up to 90%. Throughput capacity: maximum 70 kg/h (depending on material) Briquette diameter: Ø 50 mm Motor: 5.5 kW 400 Volt / 50 Hz / 3-phase Pump: 40 liters Maximum briquette length: 50 mm Optimal briquette length: 40 mm Silo diameter: 1,000 mm Oil tank: 110 liters Dimensions: 1750 x 1130 x 1100 mm (L x W x H) Weight: 950 kg Hydraulic pre-compaction via slide Main press cylinder Vertical cylinder Fill level sensor: yes Feed material requirements: - Max. chip length: 15 mm - Installation room temperature: heated space, at least +5°C - Max. load on agitator: 150 kg - Feed material must be free from magnetic metals and mineral contaminants such as sand, stones, etc. Damage to pressing tools and/or increased wear may otherwise occur.

Condition: good (used), Technical specifications: Briquetting press in good condition Year of manufacture: 2007 Technically inspected in 06 / 2025 Cylindrical briquette: 80 mm Throughput up to max. 150 kg/h *only approx. 3,949 operating hours Bedpfewtdk Tsx Agzjct - Hydraulic press: briquetting press with discharge chute - Hydraulic unit: 4 kW - Pressure: max. 300 bar - Transport dimensions: 1585/2140/H1940 mm - Weight: 1,370 kg Functional guarantee upon handover We are happy to arrange a free test run!

Condition: as good as new (ex-display), Year of construction: 2023, Ideal for shredding polystyrene or similar materials Throughput depends heavily on the sieve and source material: - up to 60 kg / h for EPS with a 15 mm sieve *the coarser the sieve, the higher the throughput Motor 9.2 / 11 KW - 400 volts, stable steel construction, hardened cutting blades, sieve with interchangeable inserts, optionally (8), (10), 15, 22, 26, 30, 40, or 60 mm perforation with electric drive with star-delta switch Ue protection and 8 m supply line ready to plug in, blow-out nozzle 150 mm, Bcedpjh S H T Uofx Agzot optionally for plastic or grain pipes, blow width approx. 12 m, chassis with 2 running wheels Ø 380 mm, and a swiveling support wheel Ø 125 mm, all Wheels with solid rubber tires, Dimensions approx. 1200 x 900 x 1270/1400 mm lxwxh Weight approx. 240 KG, Spare parts prices and options: 24 blades, hardened €9.90 each net 6 bolts €14.90 each net 1 sieve €475 each net Lid €290 each net

Condition: as good as new (ex-display), Year of construction: 2023, The ideal machine for shredding cables including optimized cutting geometry approx. 9 operating hours Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Blades: 14 pieces, 40x40mm, multi-rotatable, Rotor diameter: 260 mm, Control: Omron SPS, Cutting unit opening 600 x 800 mm, hopper volume approx. 0.6 qbm, hydraulically operated pusher Screen perforation of your choice (15 - 40 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm The following options are available at extra cost: - Double row of knives + 995 € net (28 instead of 14) - Surcharge for 4-sided segment base + € 3,750 net (prevents blocking of the pusher. Recommended for shredding plastics, paper, veneer with a thickness of less than 3 mm). - Raise shredder by 30 cm (preparation for conveyor belt) +1,980 € net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overbelt magnet + € 5,980 net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) Bea9ia3l27 Requirements for the raw material: - Mineral impurities such as sand, stones, etc. lead to increased wear. Bodpfxegmfa Ae Agzoct We are happy to carry out a free test with your material and invite you to visit us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos.

Condition: new, Year of construction: 2026, Single-shaft shredder MRZ 530 Included: + Profile rotor for increased throughput Options: Double knife row + €895 net Veneer and paper stripper + €970 net * recommended for extremely thin materials with a thickness less than 3 mm Our mütek single-shaft shredder MRZ 530 processes a wide variety of materials such as all types of wood residues, softwood, chipboard and MDF, pallets, construction timber, demolition wood, carpets, cables, paper, cardboard, and plastics. The machine is characterized by its robust design, ensuring consistent quality in continuous operation. We are pleased to offer you a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight and we will document the test with pictures and videos. Machine data: Motor: 15 kW; 400 V - 50 Hz - 3 phase Knives: multiple reversible Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Hopper (mm): 510 x 810 mm Hopper volume approx. 0.4 m³ Throughput: 1 - 5 hopper fillings/hour Hydraulically operated pusher Screen perforation as desired (10 - 40 mm) Extraction nozzle Ø 160 mm Weight approx. 1,000 kg Dimensions approx. 1550 x 1100 x 1640 mm Moisture content of raw material: must be below 30% a.d. Bcodpfx Agjd Db N Iezot Standard features included: • Fast hydraulics • Profile rotor • Control cabinet with Siemens PLC control • Automatic star-delta start • Automatic shut-off in case of rotor idle • Removable extraction channel • Speed 70 - 100 rpm for higher throughput • Cycle control to prevent idle time • Performance-enhancing step control for hydraulic pusher • Stable guides for hydraulic pusher Additional shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable 0-60 degrees Discharge height: approx. 2000 mm ± 100 mm - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) Requirements for input/raw material: - Moisture content (a.d.) must be below 30% - Metals and mineral impurities such as sand, stones, etc., lead to increased wear

Condition: new, Year of construction: 2025, Extremely strong industrial magnet for iron separation Special price 970 € net (shipping 14,90 € net) *the lengths can be seen in picture 2 The active side has a stainless steel end plate (material 1.4301). There are threaded holes on the back for mounting *handle available on request The block magnet systems can be used up to a maximum operating temperature of + 100 °C. The magnet surface should be regularly cleaned of any trapped iron parts. Starting heights for all types e.g. For a steel nut M5 approx. 60 mm For an M5 x 30 screw approx. 100 mm Installation example 1: Mounted above a conveyor belt, the iron parts "jump to the holding surface of the magnet". Installation example 2: Mounted in a piping system with direct contact to the material flow. For a high level of separation safety, it is possible to install several block magnets in a cascade, one behind the other. Installation and safety instructions: Bcsdpstqfhxofx Agzot When handling, unpacking and then installing, make sure that there are no loose iron parts such as tools or screws in the vicinity. The magnetic attraction is so strong that painful injuries can occur if fingers come between iron parts and the active surface. There should be no steel parts within a minimum distance of 400 mm below the active surface.

Condition: new, Year of construction: 2026, Another machine available immediately - December 2025 The ideal machine for shredding softwood. Bcodpfx Agewzarcjzot Motor: 11/15 kW; 400 V - 50 Hz - 3-phase Rotor diameter: 260 mm Hydraulically operated pusher Screen perforation as desired (12 - 40 mm) Extraction nozzle Ø 160 mm Weight approx. 1,100 kg Dimensions (LxWxH) approx. 1805 x 1118 x 1650 mm Colour: blue / grey Raw material requirements: - The moisture content (atro) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. will lead to increased wear. We would be pleased to offer you a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you may send us your material by forwarding agent, and we will document the test with photos and videos.