Used End Fitting for sale (8,568)

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Kedpfxoh U Rzgo Aiiodr Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: excellent (used), functionality: fully functional, tank capacity: 120,500 l, total height: 20,000 mm, inner diameter: 3,000 mm, outer diameter: 3,300 mm, wall material: stainless steel, wall structure: single-walled, number of chambers: 1, operating temperature: 20 °C, operating pressure: 3 bar, Stainless steel pressure vessel, vertical, insulated Technical data / Dimensions Available quantity: 8 Volume: approx. 120,000 liters Vessel type: Pressure vessel Condition: used Food-grade: yes Design: vertical Internal diameter: approx. 3,000 mm External diameter: approx. 3,300 mm Overall height: approx. 20,000 mm Specific gravity of the medium: 10.00 t/m³ Operating pressure: Overpressure Operating overpressure: 3.00 bar Wall thickness, bottom: approx. 6.0 mm Wall thickness, top: approx. 4.5 mm Wall thickness, shell / cylinder: approx. 3.5-5 mm Operating temperature: 20°C Material / Properties Material, inner shell: Stainless steel Material grade: V2A-1.4301 (AISI 304) External surface: Ground, welded seams passivated Welded seams, internally ground: Yes Insulation Insulation present Insulation thickness: approx. 120 mm Insulation material: Mineral wool Material, insulation jacket: Aluminum Insulation jacket: Trapezoidal sheet Equipment Base type: Foot ring / base ring Quantity: 1 Mounting: fixed Bottom type, top: Dished end Bottom type, bottom: Dished end Kdjdpfx Aiszvh Dtoior Top: 1 x Insulated dome DN 900 1 x Access opening with dome cover DN600 1 x Valve dome cover with the following connections: 1 x Cleaning-ventilation-valve combination (RLV) DN 50 1 x Vacuum valve, spring-loaded with 2 heating elements and thermostat 1 x Safety valve 1 x Burst disc 1 x Thread DN 50 for probe Shell: 1 x Condensate pipe DN 25 1 x Cable protection pipe DN 32 1 x CIP pipe DN 50 1 x Base ring made of Cr-Ni steel (1.4301) with access opening 600 x 600 1 x Spray pipe with protruding ball head Bottom: 1 x Outlet cup DN 300 1 x Outlet with cover cap, chain, and eyelet DN 80 1 x Connection fitting for sampling tap DN10 Documentation Drawing Inspection log Inspection certificate

Condition: new, Year of construction: 2022, color: grey, overall weight: 10,000 kg, empty load weight: 870 kg, loading space volume: 3 m³, loading space width: 2,150 mm, loading space length: 3,500 mm, loading space height: 500 mm, gearing type: other, driver cabin: other, Vehicle location: Bovenden, steel superstructure, doors Body: City roll-off container with hinged doors, approx. 3.8m³ - Mounting fittings for CITY hook systems to DIN 30722-3, with lubricatable and replaceable outer rollers at the rear, and UNP-140 subframe - Mounting bracket hook height 900 mm - Floor pan made of 3 mm St 37.2 (S235JR) - Side walls made of 3 mm St 37.2 (S235JR) - Rounded base tray, with 250 mm radius to the side wall - End profile made of sturdy round tube - Frame spacing 1,500 mm - Frame profile U 80 x 50 mm - Double-wing door at the rear with sturdy espagnolette lock and side central safety lock (ZV) in accordance with UVV - Door lock with container door opening aid - All-round tarpaulin and net hooks ACCESSORY INFORMATION WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! Kdsdpfx Aovhkuijiier - .

Condition: used, Year of construction: 2003, functionality: limited functionality, machine/vehicle number: 3458 F, working width: 2,500 mm, Double tenoner FRIULMAC 2003, 3+3 heads Kedpfx Ajx Rdrfsiisdr

Condition: as good as new (ex-display), functionality: fully functional, The Format4 creator 950 in a wide range of equipment variants - your CNC machine for individual woodworking challenges. Efficient CNC processing at a fair price - this principle is at the heart of the creator machine series. All models are attractively equipped with the latest CNC technology and can be customized to meet specific requirements. The creator 950 is not only an easy and safe entry into the CNC world, but also serves to relieve your CNC machining centers. Your advantages at a glance: Concentrated CNC technology on a footprint of just 5 m² All-inclusive: 4-sided formatting as standard Get started right away: Maximum productivity without set-up times No suction cup and console positioning Use from interior fittings to room doors Traditional processing from above - extremely simple loading Intuitive control via control panel Kdsdpfx Aou Eg A Uoiijr Easy to understand software Best suction result High-end at the best price in every configuration Carcass processing with Lamello Clamex-P Additional equipment: C19 2nd stop reference cylinder for long workpieces C71 Folding support tables front+rear - roller table C198 Pick-up space for tool and unit change C200 4-fold linear changer for use of units C233 Holder for crane transport C490 F4design (incl. 3-axis PP) 800 E-Learning F4Design Creator processing field: Travel of the axis X= 1475mm (bracket) Y=1550mm Z= 225 mm Working field X= 3500 mm (infinite) or 130 kg maximum load Y= 950 mm Z= 80 mm Machinable workpiece Equipped with: High-performance PC 24" LED color display Keyboard, mouse and mouse pad 1 USB interface

Condition: excellent (used), functionality: fully functional, total height: 16,250 mm, outer diameter: 3,550 mm, 5 x 125 m³ aluminum storage silo with a wide base (plastic granulate silo) Technical data / Dimensions Available quantity: 5 Volume: approx. 125,000 liters Container type: Silo Condition: used Food grade: no Design: vertical Internal diameter: approx. 3,500 mm External diameter: approx. 3,550 mm Cylindrical height: approx. 15,000 mm Kdjdpfx Aeznn Nteiisr Overall height: approx. 16,250 mm Weight: approx. 2,500 kg Specific gravity of the medium: 1 ton/m³ Operating pressure: non-pressurized Wall thickness, bottom: approx. 5.5 mm Wall thickness, top: approx. 5.0 mm Wall thickness, shell / cylinder: approx. 3.5 - 5.5 mm Ground clearance: approx. 500 mm Material / Properties Material, inner shell: Aluminum Internal welds ground smooth Notes: Material: AlMg3 / AlSi Equipment Base design: base ring/wide base Quantity: 1 Mounting: fixed Bottom type, top: conical bottom Bottom type, bottom: cone Cone angle: 90 degrees Top: 1 x roof edge railing, height: approx. 1,200 mm 1 x walkway with platform 2 x crane eye 1 x manhole DN 500 with safety grid 1 x flange DN 100 (filling line) 1 x flange DN 300 (level measurement) 1 x threaded socket for Max sensor 1 x flange DN 100 (filling) 1 x vent DN 200 with hood Shell: 1 x service access door (approx. 1,800 x 850 mm) 1 x cable protection conduit 1 x filling line DN 100, ending in a TW connection 1 x threaded socket 1 1/2" for empty indicator Bottom: The silos end at the bottom in a 90° cone with a flange DN 150 with emergency shut-off valve and suction box. Fittings available Notes: A matching access ladder (two-section) can be optionally purchased (additional cost: €1,500 plus VAT). The measuring and control technology installed on the silo will be supplied free of charge. However, no guarantee can be given for its perfect functioning.

Condition: ready for operation (used), functionality: fully functional, 🏢 20-Foot Office Container – Versatile | Robust | Immediately Available 🚛 For sale is a 20-foot office container in good, well-maintained condition. Ideal as a construction site office, storage unit, sales container, workshop, break room, or office – versatile and ready for immediate use. ✨ Features & Highlights ✅ 2 office windows on the end walls with tilt-and-turn fittings, including roller shutters ✅ 1 steel exterior door on the end wall ✅ 2 light fixtures for optimal illumination ✅ 1 electric heater – ideal for year-round use ✅ Robust steel construction ✅ Weatherproof and durable ✅ Immediately available ✅ Standard dimensions: 20 feet (approx. 6m long - 2.50m wide - 2.80m high) 📸 Condition: The container is in used, well-maintained condition with typical signs of wear and tear. The construction is stable and perfectly suitable for immediate use. Kdjdpfxsg S Alwe Aiijr 🚛 Transport: Transport can be arranged upon request or will be handled by the buyer. 📩 If you are interested or have any questions, please do not hesitate to contact us! Viewings are possible at any time by appointment.

Condition: new, Year of construction: 2020, functionality: fully functional, tank capacity: 1,500 l, Equipment: documentation/manual, BRINOX 1,500 L Process Vessel – 1.4435 – Jacketed – PED Module G – TÜV – FAT – 2020 – As New Manufacturer: BRINOX d.o.o. Tag No.: BH6722-BH1001 Year of manufacture: 2020 Condition: As new / unused CE Marking: CE 0036 TECHNICAL DATA Product type: Main/process vessel Design: Cylindrical with dished ends Working volume: 94 – 1,500 liters Empty weight: 866 kg Product contact material: 1.4435 Jacket material: 1.4307 Insulation: yes Operating pressure (vessel): -1 / +3 barg Permissible pressure (PS): -1 / +3 barg Test pressure (PT): 5.4 bar Permissible temperature (TS): -10 °C / +150 °C Date of pressure test: 2020/04 Pressure vessel according to PED 2014/68/EU Category IV Assessment procedure: Module G Notified body: TÜV SÜD Industrie Service GmbH Design code: AD 2000 SURFACES & WELDS Internal surface: Electropolished and passivated Pharmaceutical grade External surface: Industrial ground finish NDT / Inspections: RT (radiographic testing) PT (penetrant testing) Pressure testing documented 2020 EQUIPMENT • Double jacket for heating/cooling • Large frontal manway • Multiple process nozzles • CIP connections • Temperature and pressure ports • Safety fittings • Agitator mount • FDA-compliant seals • Complete piping module CONDITION • Never used in production • Stock item • Internal surface absolutely as new • No corrosion • No signs of use • Available immediately DOCUMENTATION – fully available • EU Declaration of Conformity • TÜV certificates and inspection reports • PED Module G documentation Kodpfsykuc Tex Aiijdr • Material certificates 3.1 (EN 10204) • Welding logs • NDT reports (RT / PT) • 2020 pressure test report • Surface reports • Detail and assembly drawings • FAT documents • Operating and maintenance manuals SPECIAL FEATURE BRINOX pharma process vessel in 1.4435 with electropolished internal surface, AD2000 design, PED Category IV Module G, full TÜV inspection 2020, and complete technical documentation. Project quality for sterile applications – immediately available.

Year of construction: 2019, condition: used, The Lemorau MEBR+ is a digital finishing machine based on a modular concept, allowing modules to be added according to customer requirements. The MEBR+ operates in full rotation and semi-rotation modes. The semi-rotation mode is suitable for small print runs, while the full rotation mode is ideal for large print runs at high speeds. Thanks to state-of-the-art servo technology, the registration tolerance remains consistent during acceleration and deceleration phases, as well as throughout the production process. The Lemorau MEBR+ is equipped with a servo-controlled compensation system, which ensures excellent web tension control when the machine operates in semi-rotative mode. Standard features: - Maximum rotation speed 200 m/min (656 ft/min) – label stock - Maximum rotation speed 120 m/min (394 ft/min) – die-cutting, precision fit - Maximum semi-rotation speed 40 m/min (131 ft/min), depending on the plate size – die-cutting, precision fit - Web width 250, 330, 400 mm (10, 13, 16 in) - Electronic counter (label/meter/roll counter, as well as total meter and label counter) - Adjustable splicing table with pneumatic clamps - Electronic web guiding system with ultrasonic sensor for guiding opaque and transparent materials Kdodpfxozqnxts Aiisr - Automatic web tension control via servo motors – constant and decreasing tension - Memory for 250 jobs for easy and quick job setup - 6 sets of rotary knives with lateral adjustment - 2 interchangeable pneumatic unwinders with a diameter of 25, 40, and 76 mm (1, 1.5, 3 in) - Detection of paper and matrix tears - Winding upon label entry/label exit - Remote support via internet connection - Automatic stop at the end of the parent roll with programmable end-of-roll function - Semi-automatic winding - Foot pedal for step-by-step machine operation - Multilingual touchscreen - Die-cutting repeats 203.20 – 431.80 mm (8 – 17 in) – rotation mode - Die-cutting repeats 41.30 – 371.00 mm (1.6 – 14.6 in) – semi-rotation mode - Maximum winding diameter: 600 mm (23.7 in) with 1 shaft / 350 mm (13.8 in) with 2 shafts - Maximum unwinding diameter: 700 mm (27.5 in) - CE conformity certificate Optional equipment: 1 anti-static bar 1 "Clear-on-Clear" sensor 1 corona treatment 1 speed package (80 m/min in semi-rotation mode) 1 revolver unwinder 2 flexo unit for spot coating with rotating register 1 web cleaner QRC (Quick Remote Connection) 1 new die-cutting forme with repeat lengths of 41.30 – 371.00 mm (1.6 – 14.6 in) – semi-rotary mode approx. 700 die-cutting sheets An MAHO extraction system for the trimming waste is available as an option at an additional cost!

Condition: not inspected (used), Type: 09 s mobile DC - BaA, as new, completely overhauled, air conditioning system refurbished with new compressors, hot-swap redundant UPS system, fully welded all-steel container, VdS-certified, raised flooring with cold air ducting, interior and ceiling walls clad with ISO F120 fire protection panels, three separate rooms, designed according to BSI with partitioning between technical and IT rooms, special doors (dimensions: 1,250 x 2,250 mm) with T90 fire protection, four rack systems, connection box with CEE 62 A plug, electrical sub-distribution up to 40 kW fitted with supply and return terminals, UPS system max. output: 20 kVA, high-performance air conditioning unit output: 2 x 4-14 kW, high-end racks (2 units: 600 x 1,000 x 2,000 mm; 2 units: 800 x 1,000 x 2,000 mm) with combined network/server rack systems, total rack units: 140 U, GSM messaging technology, extinguishing system: Novec I 230 fire suppression system, prepared for video surveillance installation, dimensions (L x W x H): 9,125 x 2,438 x 2,896 mm. Further detailed specifications available upon request. Located in Korschenbroich. Loading can be arranged, loading costs to be borne by the buyer. Kdjdpfx Ajy At Umeiijr

Condition: used, Year of construction: 1991, Complete mixing tank system comprising three vertical pressure tanks, each with two cooling zones, frame insulation, a bottom-entry agitator and various fittings. One of the tanks is also equipped with a CO₂ gas injection unit and a pump for tangential feed. A pipe fence, pipe panel, control cabinet and various measurement and control equipment and pumps complete the system. Additional title: Insulated, coolable stainless steel pressure tanks as a mixing system with proce Volume: 33000 l per tank Max. pressure: 2 bar Pump capacity: 28 m³/h Ksdozgcuzspfx Aiisdr Operating temperature: 40 °C Length: 2600 mm Width: 2600 mm Height: 8500 mm Weight: 3900 kg Operation / Control: Rush-Flow-Dosing: SPS-Typ = C7-633, HMI = ProTool Material: stainless steel 1.4301 Position: free standing Base construction: Cylindrical tank with dished ends and pipe feet on spherical caps Features: 2 zone frame cooling, insulation with stainless steel sheet panelling, agitator in the base, manhole at the side, tank fittings; 2 pumps; pipe fence; panel with CO2 fumigation; measurement and control technology; control cabinet with control panel; Other: Pipe fencing, pipe panels, measurement and control technology. Pumps, CO₂ injection unit

Condition: good (used), 1 x Carrot Line and Grader system Can also be used for potatoes, onions, beet root and brussel sprouts etc. System will be coming out of production end of May/early June. All equipment has had a full service and checked over during the spring period for the coming year. Haith Screen Bits Remover. The Screen Bit Remover continuously removes broken fragments of crop and debris from the produce flow. Carrots are transferred onto a traveling screen with a set size aperture. As the screen is conveyed forward, two full-width agitators gently move the crop causing any bits and debris to drop on to a waste conveyor below where the produce is taken over the end. The screen and agitator speeds are variably controlled individually to suit the various crop conditions. Grader / sorter Odenberg Titan 2 automatic camera grading system – installed in 2008. Titan 2 Sorter 6002.2, 3-way carrot sorter. The first sorter removes product that is not usable, damaged etc to the waste line. The second sorter removes short carrots, twisted and misshaped which are sent directly to the value tank. All the rejects go through the positive sorting area and the grading operative throws back any product that is fit for value sale. High capacity and low maintenance sorting machine Flexible sorting machine with gentle handling assured Quality control and feedback accessible through intuitive touch screen Consistent long-life accuracy. Grading Station. The grading operatives throw out any unusable product to the waste line via the positive grading area. Two to four graders can operate here depending on the quality of the produce. Wyma Lift Roller Sizing Grader – installed in 2019 The product is divided into five grades. 500g, 0-25mm, this goes to the value tank. 1kg, 25 – 42mm max. Loose min 30 – 45mm max. Kodpsv I S D Sofx Aiijdr Lumpers, min 45mm upwards. Oversize. The Wyma Lift Roller Sizer is a diameter grader suitable for a wide range of fruits and vegetables including carrots, potatoes, parsnips, beets, citrus, onions, bulbs, brussel sprouts, rutabaga and other round or tubular products. It is extremely versatile, offering multiple size outputs at high capacity in one machine. It can cater for a large range of product sizes and shapes through a selection of different roller options. Product size ranges, or size bands, are created by adjusting the spacing between the rollers, at defined locations, along the length of the machine. The Lift Roller Sizer is made from stainless steel and food-grade plastic materials. Five Lift Roller Conveyors. All supporting framework available. *Video available on request* Located in Wexford, Ireland. Buyer to collect – machinery will be dismantled and loaded to your vehicle. UKFM2-6653

Condition: used, This listing is for the Restek Single Position Base Plate Gas Filter Kit + SGT Gas Filter Kit The unit is in full working condition and is ready for immediate use The Restek Single Position Base Plate Gas Filter Kit is a modular system designed for gas purification in laboratory applications, particularly in gas chromatography (GC) and mass spectrometry (MS) systems. Key Features Baseplate Design: The single-position baseplate (catalogue number 22025) is constructed from brass and measures 10.2 × 10.2 × 4.8 cm. It is compatible with all standalone Super Clean gas filters Filter Cartridges: Restek offers various filter cartridges, such as the triple filter that removes oxygen, moisture, and hydrocarbon impurities, and the fuel gas filter designed for moisture and hydrocarbon removal. Fitting Compatibility: The baseplate accepts 1/8" tubing. To adapt to 1/4" tubing, 1/8" to 1/4" tube end reducers are available. Material Options: End fittings are available in brass or stainless steel, allowing for customization based on application requirements Restek SGT Superclean Gas Filter Kit The Restek SGT Superclean Gas Filter Kit is a high-purity gas purification system designed to remove contaminants such as moisture, oxygen, and hydrocarbons from carrier and fuel gases used in gas chromatography (GC) and mass spectrometry (MS). This kit is particularly beneficial for applications requiring ultra-pure gas supplies to ensure accurate and reliable analytical results. Key Features High-Purity Output: Delivers gas purity levels exceeding 99.9999%, depending on the incoming gas quality and flow rate. Versatile Compatibility: Compatible with various gas types, including inert carrier gases, air, hydrogen, and helium. Quick-Connect Design: Features a user-friendly quick-connect system for easy and leak-free filter cartridge changes. Durable Construction: Constructed with a glass interior to prevent diffusion and a polycarbonate exterior for safety. Kedpjxv Dk Nofx Aiijdr Visual Indicator: Each filter cartridge includes an easy-to-read color change indicator to signal when replacement is necessary.

Condition: ready for operation (used), functionality: fully functional, The Lutetia T40 tumbler is designed for processing plants seeking to secure their mixing operations with proven equipment. It ensures consistent and controlled blending of mixtures, contributing to uniform quality across all productions. As a result, recipes remain consistent and batch-to-batch variations are minimized. Additionally, the design of the drum promotes continuous movement of the materials, which improves final product homogeneity. Kdedpjyfn Hbofx Aiisr This tumbler integrates easily into existing production lines due to its layout, which meets the demands of daily industrial use. The front discharge configuration simplifies end-of-cycle unloading and enhances process throughput. Furthermore, the overall ergonomics make it easy to load the machine, reducing unnecessary handling. This results in more efficient and consistent operator workflows. When Europ’Équipement refurbishes a Lutetia T40 tumbler, all mechanical and functional components are thoroughly checked. This ensures the user gets a reliable machine, ready for immediate integration into their facility. Refurbishment also represents a cost-effective alternative to new equipment, providing an industrial performance level while controlling budgets. Therefore, this solution fits within a sustainable and rational investment logic. The Lutetia T40 is suitable for meat processing and value-added food applications that require continuous and repeatable operation. Its capacity meets the needs of medium-sized productions, making it a logical choice for industrial operators aiming to strengthen their production tools and secure their processes. Technical specifications: - Meat and brine capacity: 2,000 – 2,200 kg - Usable volume: 3,675 L - Operating mode: rotating drum - Discharge: large-capacity front mouth - Dimensions (L × W × H): 3,250 × 1,550 × 1,990 mm - Drum diameter: 1,440 mm - Loading height: 1,110 mm - Machine weight: 1,500 kg

Year of construction: 2000, condition: excellent (used), functionality: fully functional, 2 x 50 m³ aluminium silos with long support ring, ø 3,000 mm (plastic granulate silo) Capacity: approx. 50,000 litres Manufacturer: Eichholz Year of manufacture: 2000 Quantity: 2 Diameter: approx. 3,000 mm Cylindrical height: approx. 10,000 mm Total height: approx. 11,250 mm Weight: approx. 1,400 kg Bulk density: 0.6 kg/dm³ Material: AlMg3 Connections and fittings: On the top deck: 1 x roof edge guard rail (ø 3,000 x 1,250 mm) 2 x crane eyes 1 x manhole DN 600 with vent nozzle 1 x flange DN 100 (filling) 1 x flange for level indicator 1 x threaded socket 1 1/2" (full indicator) On the shell: 1 x filling line with pipe supports 1 x access door (approx. 850 x 1,850 mm) Ksdexvtvzjpfx Aiijdr 1 x cable protection conduit 1 x threaded socket (1 1/2") for empty indicator Silo ends in a 60° cone with emergency shut-off slide valve. Otherwise as per photos

Condition: used, first registration: 12/2022, New overseas container with only one trip Steel container with rear doors. Wooden floor, etc... On request and for an additional charge also with interior fittings as an office, sanitary or residential container. Price is ex works. Rental period at least 1 month / 30 days Short-term rental up to 3 months 4.00¤ / day, rental period longer than months 3.00¤ / day Ksdevw Hmgspfx Aiijdr After the end of the minimum rental period, billing is done on a daily basis. Plus the costs for delivery and collection. Also available in 40ft 10ft or 8ft on request.

Condition: refurbished (used), Year of construction: 2015, functionality: fully functional, color channels: 8, Vutek GS 5000 LXpro LED 5 m UV roll printer with LED lamp Very low noise and quick start-up Resolution: 12pl-1000 dpi Colors: 8C CMYl + Light colors, white (over and under print) Speed up to 224 m²/h Mesh Kit - Fully refurbished with warranty by EFI dealer Available now, end of April. Kdodpfx Aieyzg Nbjijr

Condition: good (used), functionality: fully functional, Year of construction: 2007, operating hours: 1,153 h, DYNO-MILL KD 6 Agitator Bead Mill (2007) For sale is a DYNO-MILL KD 6 horizontal agitator bead mill, manufactured by Willy A. Bachofen AG (WAB). This machine is a premium Swiss-made unit designed for the continuous dispersion and wet-grinding of pumpable products, ranging from low to high viscosity. This unit was manufactured in 2007 and decommissioned in fully functional, running condition with no known faults. It is distinguished by its exceptionally low usage history, having logged only 1’153 operating hours. It comes equipped with a high-wear-resistant Silicon Carbide (SiSiC) inner cylinder and hardened stainless steel discs. It is sold as a complete bundle, including a peristaltic pump, a tool kit, the original electric cabinet and yttrium-stabilized zirconium balls (used). Highlights • Low Usage: Only 1'153 operating hours—internal mechanics are in excellent condition. • High-End configuration: Fitted with a ceramic Silicon Carbide (SiSiC) inner cylinder (6mm wall thickness) and hardened stainless steel discs for durability and contamination control. Sintered Silicon Carbide (SSiC) prevents product overheating significantly better than Zirconium or Steel liners. • Ready to Run: Sold as a complete package including the Electric Cabinet and a Peristaltic Product Pump. • Features the industry-standard WAB dynamic gap separator and pressure-balanced mechanical seal. • Voltage: Fitted with a modern Danfoss VLT frequency converter featuring wide-range input (380-480V, 50/60Hz), making the machine immediately compatible with both European (400V) and US (480V) power grids without modification Technical Specifications • Manufacturer: Willy A. Bachofen AG (WAB), Switzerland • Model: KD 6 Kdjdpfjx Tdyzsx Aiisr • Grinding Chamber Volume: 6.0 Liters (Net volume ~5.7 Liters) • Throughput: approx. 50 – 200 kg/h (dependent on product/viscosity) • Main Drive: 11 kW Motor (440V / 60Hz rated) • Separation System: Dynamic gap separator (Tungsten Carbide rotor/stator) with adjustable gap width (0.15–1.0 mm) • Shaft Seal: Double mechanical seal (DGD) with integrated pressure rinsing circuit • Cooling: Forced water cooling jacket for the grinding cylinder • Weight: 695 kg 
 Scope of Delivery • Mill: DYNO-MILL KD 6 base unit • Grinding System: Silicon Carbide (SiSiC) Inner Cylinder & Hardened Stainless Steel Discs • Feed Pump: Peristaltic Pump included • Controls: Original Electric Cabinet included • Grinding Media: Ceramic Beads, Zirconia Partially Stabilized with Yttria, four sizes, each approx. 25Kg (0.4 - 0.6 mm / 0.8 - 1.0 mm / 1.2 - 1.4 mm / 1.6 - 1.8mm) • Documentation: Operating instructions and wiring diagrams Condition • Mechanical: Excellent, running condition with no known faults at the time of decommissioning. • Cosmetic: The machine is clean but shows minor cosmetic wear (see pictures for visual details) • Last application: Food Typical Applications • Ideal for fine particle size reduction in industries such as: • Paints, Inks, and Coatings • Agrochemicals and Chemicals • Life Sciences and Microbiology • Food and cosmetics We ship worldwide. If you are interested or have any questions, please get in touch! Can be inspected in Liestal, Switzerland.

Condition: like new (used), functionality: fully functional, Year of construction: 2007, laser power: 4,400 W, Used Very Clean 4.4kw Bystronic Byspeed 3015 CNC laser for sale Used Bystronic 4.4kw lasers for sale VIDEO BELOW: Byspeed 3015 4.4kw – Loading system in the video not included Installed new/year: 2007 Manufacturer: Bystronic Model: Byspeed 3015 Sheet size: 3metre x 1.5metre / 3000mm x 1500mm Laser power: 4.4kw / 4400 watt Control: ByVision CNC02 Automation n/a Year: 2007 Condition: good working condition / service from new Byspeed 3015 4400w Turbo Blower Hours: 2,987 hrs – New turbo fitted end of 2023 under Bystronic warranty Good condition machine that has been covered from new by service contract with Bystronic UK Options Included: Kdodpfx Aijr Hcm Djisr Bypos automatic focus CutControl 2 cutting heads Tools and accessories Torit Dust collector

Condition: used, mileage: 153,000 km, power: 70 kW (95.17 HP), first registration: 12/1992, overall weight: 3,200 kg, fuel type: diesel, color: red, next inspection (TÜV): 12/2025, gearing type: mechanical, Year of construction: 1992, total length: 5,345 mm, total width: 1,975 mm, total height: 2,680 mm, number of seats: 9, Equipment: had accident, parking heater, Original German vehicle. In service with a small municipality until 2026, initially used by the fire brigade and then by the municipal works department. This vehicle has civilian truck registration as a "box body truck" and is officially rated for 9 seats in the registration papers. The vehicle was originally operated as a multi-purpose vehicle (MZF), and afterwards was used to transport the municipality’s lawn mower. Only 1 bench seat is permanently mounted. 2 of the 3 bench seats were not used in recent years and are included loose. The original seat belts and mounting bolts are also supplied. A fold-out table with a radio handset is still installed on the left side, and a genuine large fire brigade first aid kit is integrated into the fit-out. OM 602 engine, 5-cylinder naturally aspirated diesel with 2874 cc. The engine always starts perfectly and runs cleanly at first, but after about 20 seconds at idle the running characteristics at idle worsen significantly and smoke develops. Once warmed up, the smoke subsides and the engine runs cleanly again, almost normally. The engine is either heavily worn or there is engine damage. No precise diagnosis so far. The vehicle drives immediately and functions well; typical engine power was fully and consistently available during a brief test drive, but we do not guarantee roadworthiness. A repair is certainly necessary in the near term! Kodpoyx N Hqefx Aiisdr For driving short distances or boarding a RORO ship at port under its own power towards Africa, this 310 D appears completely unproblematic. 5-speed manual transmission. 127 km/h top speed. Tow hitch (ball head) with a braked trailer load of 2,000 kg or 750 kg unbraked. Power steering. Factory-installed auxiliary heater Mercedes/Eberspächer (working). Bodywork has isolated rust spots; overall, due to years of storage indoors, the vehicle is still in comparatively good condition. The passenger door window is broken and covered with a film. The paint below has previously been touched up in black. The vehicle clearly received very good maintenance while with the fire brigade—unfortunately, this was not maintained afterwards. Opening the sliding door mechanically deploys a large step. Unladen weight: 2,370 kg. Gross vehicle weight rating: 3,200 kg. External overall vehicle dimensions: Length 5,345 mm / Width 1,975 mm / Height 2,680 mm. The tires (205R14C) are from 2013 and not cracked, tread depth approx. 50-60%. The vehicle is primarily intended for export or for genuine fans of the Bremen transporter who are looking for a completely unvarnished basis for restoration. MOT expired 12/2025, will not be renewed. We do not have our own workshop. We have deliberately priced the vehicle attractively, as genuinely good comparable vehicles are now usually being traded for double or even higher prices. A personal inspection is highly recommended due to the defects and can be arranged by appointment. This offer is only valid for businesses, freelancers, and public authorities of any kind. Sale to private end users is strictly excluded. Subject to prior sale and errors. The purchase price is gross = net, with no VAT incurred (according to §25a of the German VAT Act / margin scheme).

Condition: refurbished (used), For Sale: Refurbished EOS M290 – Ready to Use This fully inspected and refurbished EOS M290 is in excellent condition! This setup is ready to use and ideal for expanding or starting a DMLS production line. Specifications: • Technology: DMLS (Direct Metal Laser Sintering) • Material Type: Metal • Compatible Materials: On Request Kdsdpfxewmq Dye Aiior • Build Volume: 250 x 250 x 325 mm • Laser Type: Yb-fiber laser; 1 x 400 W Consumables Featured We offer plug-and-play materials, fully tested and optimized for use with EOS machines. Our exclusive Inframotion PA12 is designed to perform at or above OEM powder levels, while significantly reducing costs. By switching to our materials, you will reduce your production costs without compromising on quality. Included Services: • Transport & Installation: We ensure safe delivery in original EOS packaging and professional installation. • Warranty & Maintenance Plans: Flexible options to fit your needs, for long-term reliability and peace of mind. About Inframotion 3D (IM3D) At Inframotion 3D B.V., we are the market leader in high-quality remanufactured EOS SLS and DMLS machines with comprehensive support services. We are the only provider to offer end-to-end solutions for used EOS equipment, with unmatched expertise and reliability. What we offer: • Expert maintenance: Installation, maintenance, repairs and upgrades performed by experienced ex-EOS technicians. • Exclusive materials: Cost-effective, high-quality consumables such as our plug-and-play PA12, specifically designed for EOS systems. • Unmatched support: From transportation to maintenance plans, we have it all covered. Trust IM3D for top performance, superior materials and the expertise to keep your SLS and DMLS production running smoothly. Please feel free to contact us for more information or questions!

Year of construction: 2023, condition: like new (used), functionality: fully functional, A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery Rental Multiprocess System in wear protected design. Stand-alone lab scale grinding and classifying plant. This compact plug-and-play system is perfect for Research and Development (R&D) and small-scale productions. It operates in small batches of a few kilos. The system can be fitted with different modules (one at a time) to either grind or classify different products, both coarse and super fine grinding are possible, providing a wide variety of end results. The exchange of the different modules is fast and easy, allowing to perform different tasks in a short time. *Jet mills are subject to export license depending on destination country ALPINE multi-process plant AFG 100 (MPS) The basis of this concept is the use of a basic module which combines all the additional components of a grinding/classifying plant (frame, dosing system, fittings, separator filter, control system etc.). In just a few simple steps, appropriate modules can be integrated to implement various grinding and classifying processes in this one machine: • ALPINE Fluidized Bed Opposed Jet Mill AFG 100 • ALPINE Turboplex Fine Classifier ATP 50 • Alpine Zirkoplex Classifier Mill ZPS 50 • Alpine Dry Agitated Media Classifier Mill Pulvis 150 PV • Alpine Aeroplex Spiral Jet Mill 100 AS Characteristics: • Multi-process plant offers maximum flexibility • Small-scale production on a qualified, GMP-compliant plant • Use of scale-up capable process technology • Short change-over and assembly times as well as easy cleaning due to optimized disassembly. • Compact plant design on a laboratory scale • Ready-to-use system on delivery Design: Design: Non Pressure Shock Resistant (NPSR), suitable for inert operation (N2) Kdsdpfx Aijr Iig Sjier ATEX - inside non ATEX - outside non ATEX Material of construction - product contacting parts: stainless steel and wear protection - non product contacting parts: stainless steel, plastic (PE-HM) Wear protection: ceramic and Vulkollan (Polyurethane) Batch operation, for a few kilos normally (product dependent) Scope: Hosokawa Alpine Multiprocess System in wear protected design. Complete system with feeding screw, grinding or classifying module, cyclone, filter, blower, control cabinet, motors Can be fitted with the following modules: 100 AFG, 50 ATP, 50 ZPS, 100 AS and 150 PV

Condition: new, Year of construction: 2026, 10T Ramp, Usable Internal Width 1.7m – TM-GROUP, the Best Choice on the Market ✅ Specifications: - Manufacturer: TM-GROUP - Maximum Load Capacity: 10 tons - Internal Ramp Width: 1700 cm - Reinforced side railings on both sides - Ramp rollers for easy movement - Central ramp handle for forklift repositioning - Adjustable slope and flap height - Dual reinforced ramp supports - Moving parts equipped with grease fittings - Ramp also equipped with a winch - ELECTRIC and manual ramp height control ✅ Ramp Surface Grating: Grating with anti-slip grooves. Safe and secure surface. Both forklifts and pedestrian movement enjoy the best possible grip and solid support. Competitors typically offer ramps with a metal sheet covered with mesh. Our product features grooved grating – a much more durable solution that prevents dirt from staying on the ramp and ensures the forklift doesn't slip. ✅ Forklift Mount – Installable on Both Sides: Convenient and quick forklift attachment allows for ramp transport in all directions. The specially designed handle enables maneuvering the ramp even in tight spaces. ✅ Chain for Connecting to TIR Truck, Railway Car, or Fixed Warehouse Dock: A solid steel chain is another strength of our ramp, providing additional safety by preventing the ramp from shifting during loading operations. ✅ Sturdy Side Railings: Safety railing with the option to detach and install a frame/roof structure (roof is optional). ✅ Electric Height Adjustment Control: Smooth electro-hydraulic drive powered by a high-end pump. The pump requires only 230V, making it usable with a standard power outlet. ✅ Dual-Action Manual Pump: Hydraulic pump for height adjustment in case electro-hydraulic power is unavailable – dual lifting mechanism. This is an ideal solution for working in all conditions. ⭐️ We Offer the Following Variants: ⭐️ Driveway widths: 1700 cm, 2000 cm, and 2500 cm – Standard, Premium, and Premium Plus. Mobile ramps with load capacities of 10 tons, 15 tons, 20 tons, and 25 tons. Ramp grating thickness: 3–5 cm. Kodpfowa Nr Njx Aiiodr Colors: red, blue, black, and green (custom colors available on request) Mobile ramp with tarpaulin cover. As a manufacturer, we can produce ramps tailored to special, individual orders – in different sizes, load capacities, and configurations. Need a custom solution you can’t find anywhere else? Contact our specialist. Tags: Loading ramp, unloading ramp, loading dock, mobile ramp, loading bay, transfer dock, mobile loading dock, mobile loading ramp.

Year of construction: 2009, operating hours: 89,479 h, condition: good (used), functionality: fully functional, Grinding robot for machining forged or cast water fittings, operating air pressure 5.5-6 bar, operating voltage 400 V-50 Hz, rated current 13 A, Kdjdpfx Aiszvn Tzoier rated power 8 kW, ongoing maintenance until 2026, extensive range of accessories.

Year of construction: 1979, condition: good (used), 1 x 90 m³ aluminum silo with extended base and filter housing, ø 3,000 mm designed for a specific weight of 0.6 kg/dm³ (formerly used as a flour and starch silo) Manufacturer: Zeppelin Capacity: approx. 90,000 liters Diameter: approx. 3,000 mm Overall height: approx. 15,950 mm + 1,200 mm railing Ksdpfjgig D Dsx Aiiedr Weight: approx. 4,000 kg Specific weight: 0.6 kg/dm³ Material: Aluminum: AlMg3 Food grade: yes Insulation: approx. 100 mm mineral wool with screwed-on cover plate (cover plate partially damaged, but can be repaired by us). Connections and fittings: On the top: 1 x roof edge railing (ø 1,800 x 1,200 mm) with two access openings 1 x hinged dome with protective grid DN 600 1 x access ladder to the filter housing 2 x crane eyes In the filter housing: 1 x flange DN 100 for filling line 4 x ventilation opening DN 600 with filter bag 3 x connection for control/measuring technology In the shell: 1 x ventilation grid (filter housing) 1 x filling line 1 x access door (approx. 1,850 x 800 mm) The silo ends in a 60° cone NW 1500 with a manhole. The cone is equipped with a fluidized bed (compressed air) and a rotary valve. The silo does not have rupture discs or explosion protection devices. For further information: see technical drawing and images.