Hydraulic unit

ORSTA-Hydraulik Typ 6l/200 bar

Condition: ready for operation (used), Year of construction: 2012, A stationary Putzmeister concrete pump in trailer design is available. Motor power: 7.5kW, max. delivery pressure: 40bar, delivery capacity range: 30l-90l/min, max. aggregate size: 8mm, piston stroke: 130mm, piston diameter: 100mm, mixing hopper volume: 170l, feed hopper volume: 200l, filling height: 1300mm. Machine dimensions X/Y/Z: approx. 3650mm/1600mm/1600mm, weight: approx. 1200kg. Documentation available. An on-site inspection is possible. Kjdpfx Aeycigdeb Todi

Condition: new, Year of construction: 2025, 2-roll driven profile bending machine Hydraulically adjustable top roller Shaft diameter: 40 mm Roller diameter: 152-162 mm Revolutions: 8.5 per min. Top roll adjustment: 120 mm Capacity table: in the attachment Machine available in various versions: Kjdpfxjhgiuhs Ab Tsdi Manual adjustment, 3-roll driven etc.

Condition: new, Year of construction: 2025, An active lime production line is a set of equipment designed to produce high-quality lime from limestone, with the aim of meeting various industrial applications, such as in the production of steel, environmental desulfurization, and other processes. The process typically involves several stages, including limestone crushing, calcination, hydration, and finally, the production of active lime. Here is a general overview of the main steps involved in an active lime production line: 1. Limestone Quarrying: - Raw limestone is extracted from quarries and transported to the lime plant. The limestone may undergo crushing and sizing processes to achieve the desired particle size. 2. Limestone Preheating: - The raw limestone is typically preheated in a preheater or precalciner before entering the rotary kiln. This preheating step helps to reduce the energy consumption in the kiln by partially decarbonizing the limestone. 3. Loading into the Rotary Kiln: - The preheated limestone is loaded into the rotary kiln, a large, rotating cylindrical furnace. The kiln is inclined at a slight angle to facilitate the movement of materials through the kiln. 4. Calcination: - In the rotary kiln, the limestone undergoes high-temperature calcination (typically in the range of 900 to 1,450 degrees Celsius). This process causes the limestone to undergo chemical and physical changes, converting it into lime (calcium oxide). 5. Cooling: - After calcination, the lime moves through the cooling zone of the kiln, where it is cooled down. This cooling step is essential to stabilize the lime and prepare it for further processing. 6. Hydration: - The quicklime produced in the kiln is then slaked with water in a hydration process to produce slaked lime (calcium hydroxide). This is typically done in a separate hydrator. 7. Separation of Unreacted Lime: - The slaked lime is separated from any unreacted quicklime or impurities. This step ensures that the final product is of high quality. 8. Filtering and Drying: Kedpfsq Nyzbsx Ab Todi - The separated slaked lime is filtered to remove excess water, and the resulting product is dried to achieve the desired moisture content. 9. Storage and Packaging: - The final product, active lime (calcium oxide), is stored in silos or other storage facilities. It can then be packaged for sale or transported to end-users. 10. Environmental Considerations: - Dust collection systems and other environmental control measures are often implemented to minimize emissions and ensure compliance with environmental regulations. The design and configuration of an active lime production line can vary based on factors such as the type of limestone used, production capacity requirements, and specific industrial applications. Modern production lines often incorporate advanced technologies to optimize energy efficiency, minimize environmental impact, and ensure high-quality active lime production.

Condition: good (used), Year of construction: 1990, machine/vehicle number: 5211, Offer 24289 Technical data: - max. cutting width 3060 mm - max. cutting capacity at 45 Kp/mm² 4 mm - Cutting angle 1.50 ° - Cutting gap - adjustment via adjusting screws - Number of hold-down devices 15 pcs - Stroke rate 23 to 43 /min - Front angle stop - Motorized backgauge position-controlled 15 - 850 mm - Cutting line lighting - E - foot switch Ksdpot Ucgajfx Ab Tsdi - Drive 400 V / 7.5 kW - Space requirement approx. W 3900 x H 1600 x D 2400 mm - Weight approx. 4.5 t

Year of construction: 1965, condition: used, machine/vehicle number: 4447, working width: 2500 mm metal sheet thickness: 4 mm throat: 70 mm rear stop: 520 mm power: 380 V, 6,3 kW space needed: 3200 x 2300 x 1270 mm weight: 4600 kg Kdsdpeb H Ibujfx Ab Tji

Condition: good (used), Year of construction: 1998, machine/vehicle number: 0618012, Offer 24604 Kjdpfx Abjvncubs Todi Technical data: - suitable for welding steel, aluminum, special metals, Cr Ni, etc. - welding current 450 A 60% ED - 360 A 100% ED - welding current adjustable from 3 A - 450 A - Synergic setting control FRONIUS - water cooling device FRONIUS - separate wire feed case - intermediate package device - wire feed case 1 linear meter - 4 rollers wire feed continuously adjustable - MIG - MAG hose package water-cooled approx. 4 linear meters - ground cable - pressure reducer - mobile base frame - connection 400 V / 6.6 A / 8.7 kVA space requirement approx. W 650 x H 900 + 450 x D 1100 mm - weight approx. 200 kg

Condition: used, Year of construction: 1978, sheet width 3100 mm plate thickness 2 mm rear stop 1000 mm cutting angle 1°06 ° no. of strokes 45 Hub/min total power requirement 3,0 kW dimensions of the machine ca. 3600 x 2200 x 1600 mm weight 4500 kg Equipment: - Electric motorized backgauge - With digital ELGO position display - Manual cutting gap adjustment - 1x side stop with mm scale - 2x support arms Kodpjuagxpjfx Ab Tjdi - 1x freely movable double foot switch - Front finger guard Special accessories included: - Pneumatic sheet metal holding device for thin sheet metal cuts

Condition: new, - Shaft diameter 50 mm - The upper roller is hydraulically moved - Three rollers are driven - Digital display Kodpfxsgg N Two Ab Tsdi - Can be used horizontally/vertically - Foot switch - Emergency stop - Documentation - 400 V

Condition: refurbished (used), functionality: fully functional, Extrusion Screen Changers - Continuous Screen Changers Double Piston Filter - - Immediately available, on request also with control, hydraulic unit. When making your request, please let us know your desired capacity and the material so that we can offer you the right filter. Kdjdpfoh Itl Sex Ab Toi

Year of construction: 1972, condition: used, machine/vehicle number: 32 416, max. working width: 1530 mm for metal sheets up to: 2,5 mm opening width top clamping bar: 290 mm adjustment bending cheek: 90 mm clamping bar drive: 1,1 kW below cheek drive: 3 kW rear stop: ja mm weight: 2200 kg Ksdpfx Ajy Np Aob Todi space needed: 800x3000x1380 mm