Chain link fance machine

WAFIOS AF 30

Condition: excellent (used), Year of construction: 1995, Combination Unit: Manufacturer: GSG Feeder: Type: 840.02-027 Crusher Descaler: Type: 663.02-017 Wire Range: Ø5.5-16mm For wire rod with approx. 40-60 daN/mm² strength Crushing and Bending Rollers: Carbide Inserts Adjustment with 0.37 kW - 1.15 A gear motor Brush Drive with 0.25 kW gear motor, n=293 rpm Connection Voltage: 380-420 V 50 Hz Dry Coating Unit: Type: BSG/T Filling: Calcium Stearate (e.g., Traxit Type: D S 51 E) Stearate Consumption: approx. 350 g per t of wire Drawing Speed: max. 15 m/s Electrical Power: 2x 0.55 kW gear motors Cassette: 2 slots (supplied with 1x roller block + 1x cassette) Type: PKG/T (TS) Cleaned rolled wire Wire strength approx. 40–60 daN/mm² Wire range max. inlet diameter 9.5mm, finished diameter 3.5–8.5mm Roll dimensions min. Ø115mm, max. Ø125mm, Bore diameter Ø82mm, width 15–25mm Cooling pin diameter 25mm Cooling water consumption approx. 600 l/h Drawing machine: Manufacturer: Koch Type: KHZ 5000 Year of manufacture: 1993 Serial number: 13.821 Number of draws: 1 draw per block Drawing drum: Ø700mm Tensile force: mechanical 5000 N Wire material: mild steel wires Run-in strength: approx. 40 – 45 daN/mm² Maximum drawing range: Inlet diameter 5.0 – 8.5mm Cross-section reduction: 20 x 25% (mechanical gradation) Drawing speed: up to max. 7.0 m/s Brake: Twiflex, type: MRB Drive: AC motor/frequency converter, Siemens PN=110 kW, n=1485 rpm Spooler: Manufacturer: Koch Ncsdpfx Alor Nfvmjajw Type: KHS 1250 Year of manufacture: 1993 Factory No.: 13741 Wire diameter: 5 – 8.5 mm Strength: approx. 55 – 70 daN/mm² Winding speed: V=7 m/s, adapted to the drawing machine Filling weight: approx. 3000 kg Spool drive motor: Three-phase motor with external fan Type: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000-2000 rpm, IP54, design B3 Laying drive motor: 66-671U, 1.5 kW, 170 V, 9.8 A, 1680 rpm, IP 44, B5-200 With Attached tachometer generator TG 20, 20 V / 1000 rpm With attached spur gear SK 32, i=57.53, design B6 Hydraulics: Hydraulic excavator type: H13 AK Pneumatics: Twiflex disc brake type: MRB Pneumatic cylinder type: SPWG 28032-25mm stroke Dimensions: 3100 x 3000 x 1700 mm (L x W x H) without counterweight

Year of construction: 2016, condition: excellent (used), functionality: fully functional, Make: Reifenhauser Model: Mirex-MT-V 1-RZE 120-1800 Year: 2016 Condition: Excellent Use: PET / PP / PS Foil or Sheet PET: Thickness Range: 0.25 - 2.2mm Output: 2,000 kg/h Max Sheet Width: 1600mm Extruder: RZE 120mm Electrical Supply: 3 x 480V 60Hz with N Calendar Roll Width: 1800mm Calendar Roll Diameters: 450 / 700 / 700mm Silicon Bath Max Sheet Width: 1600mm Silicon Bath Sheet Thickness Range: 0.15 - 1.5mm Nsdpfxovbcbue Alajcw 4 Position Winder WOB 1800 for double web winding included. All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale.

Condition: new, Year of construction: 2025, Metal picket fence roll forming machine MFP-1 was designed by our company to produce semi-round shape picket metal fence profile. This profile is widely used and popular among companies with business in manufacturing, installation and selling of metal fences. The production of the profile goes gradually, at first hemming forms on edges from the flat metal, and then the height of the profile and the semi-round shape are formed, at the last stage of rolling machine forms the rib in the profile center. Such number of forming stages makes it possible to ensure smooth sheet changes during rolling, as well as high quality of the final product. As a blank, you can use a strip of required width and length, to prepare it with pre-cut on other equipment – sheet metal slitting machine or guillotine shear. After roll forming, to make fence picket end look better, you can use special cutting press of our production. The working tools of such press have special round configuration and are the same as semi-round metal picket shape to make appropriate cutting. Those tools are made from special tool steel, and goes through process of hardening so ensure high requirements for the cutting tools of the equipment. Ncodpfx Alom Twnlsaew Our company can produce as semi-automatic rolling machine for the metal fence pickets manufacturing and a manual punching press for it, as well as a fully automatic line. Such metal fence automatic line can have following components: console metal decoiler, a rolling machine equipped with an automatization system with the ability to program the number of required pickets for rolling and their lengths, automatic electric shear for cutting metal at the end and stacker part. Thus, cooperating with us, our customers can choose the best option for their manufacturing process according to their planned production volumes, budget, etc. For more details about metal picket fence roll forming machine MFP-1 please contact our sales department

Condition: ready for operation (used), Year of construction: 2001, A complete 5-layer coextrusion blown film line with 5 extruders and all peripheral equipment is available. Total line dimensions X/Y/Z: 14m/22m/11m, blow head: Kiefel Worms FSBK 500 with IBC, die diameter: 500mm, film width range: 700mm-2000mm, haul-off width: 2000mm, winding width: 2000mm, line speed: 120m/min, melting capacity: 500kg/h, total power requirement: approx. 300kW. 1) Double winder Wintech, winding width: 2000mm, film thickness range: 35µm-150µm, max. roll diameter: 1000mm, max. roll weight: 1900kg, core inner diameter: 152mm/6inch. 2) Extruder Kiefel Worms 70.29D, power: 89kW, screw: 5-zone barrier screw, speed: 125rpm, renewed: 2010. 3) Adhesive extruder Kiefel Worms 50.25D, power: 34kW, screw: 3-zone barrier screw, speed: 200rpm. 4) Center extruder Kiefel Worms 50.25D, power: 34kW, screw: 3-zone core progressive screw, speed: 175rpm. 5) Adhesion promoting extruder Kiefel Worms 50.25D for the outer layer, power: 34kW, screw: 3-zone barrier screw, speed: 200rpm. 6) Kiefel Worms 80.25D outer layer extruder, power: 125kW, screw: 5-zone barrier screw, speed: 150rpm. 7) Reinhold SRK 200/9.6 film calibrating device. The entire line is controlled by a Plast Control system. Further components: integrated width measurement, C-scan for profile measurement, web center control, corona pre-treatment, film pre-draw. Including a replacement FSBK 5-layer blow head with IBC, replacement rollers, annular gap blower with filter, suction units, crane and external system terminal. Documentation available. On-site inspection is possible. Njdpfx Asv T An Selaecw

Year of construction: 2007, condition: excellent (used), EXTRUDEX EXTRUDER EN50-30D year 2007 no. 4101264, with melt pump, screen changer and 5 layer pipe head Year of manufacture 2007 As well as 4 co-extruders EXTRUDEX EN25-25D, year of manufacture 2007 APPLICATION: Production of PE 5 layer pipes Max diameter 32 mm INVENTORY: Nsdpfx Ajvyaxuslascw 1 single-screw main extruder EN 50 4 co-extruders single-screw auxiliary extruders The extrusion system is my property Location: D-26345 Bockhorn-Grabstede, Bahnhofstr 6, Germany

Condition: new, We would like to offer shafts specifically designed for medium-sized shredders equipped with side combs, a breaking bar, and a cassette system. Suitable for models: LINDNER U75, ARJES VZ750, HAMMEL VB750OL, NOVA 75DK - 5-7-7 - 6-7-7 - 8-7-7 - 10-7-7 MRW 2.85: - 5-8-8 - 6-8-8 - 8-8-8 - 10-8-8 PROTECHNIKA is a company with a 21-year history, specializing from its inception in the manufacturing of spare parts and complete recycling systems. In recent years, we have expanded our product range to include grinding shafts for slow-speed shredders. Through the implementation of automated welding processes and proprietary production technologies, we have successfully reduced production lead times while maintaining consistently high quality standards. Grinding shafts are a serial product, which also allows us to collaborate with machine manufacturers on an OEM basis. Ncsdpfx Aljx Hhwdsajw What sets PROTECHNIKA apart from the competition? The answer is simple: - Certified 3.1 materials - TUV SUD Rheinland quality assurance - ISO 9001 certification - Automated welding processes / ISO 15613 / ISO 15614 - Welders certified to ISO 9606-1 - ISO 9001:2015 - ISO 14001 - Independent design department able to fulfil any customer-specific requirements - In-house Research and Development Centre Building long-term customer relationships is our top priority, as your satisfaction is our success!

Condition: used, Semi-automatic PET bottle blow molding machine Manufacturer: FERENC Nedjugu E Repfx Alaecw Model: F-1400 Year of manufacture: 2006 Output: approx. 800 pcs/h Number of molds in the machine: 2 x 5 L (48 mm cap) Oven dimensions: - Length: 900 mm - Width: 900 mm - Height: 1200 mm Blow molder dimensions: - Length: 1800 mm - Width: 750 mm - Height: 2000 mm Set weight: 1200 kg Technical condition: used machine

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: D12L/8263, Offer Number: D12L/8263 Machinetype: wire nail press Make: WAFIOS Type: N90 Ncodpewi Tg Aofx Alaew Constr. year: 1997 diameter range: 2,0-4,0 mm nail length: 50-100 mm output - pieces/min: 800 Location: In our warehouse

Condition: new, Year of construction: 2026, functionality: fully functional, total length: 30,000 mm, total height: 4,300 mm, total width: 6,500 mm, workpiece weight (max.): 100 kg, temperature: 220 °C, heating capacity: 80 kW (108.77 HP), workpiece height (max.): 1,200 mm, workpiece length (max.): 2,500 mm, insulation material: Mineralwolle 75 kg/m³, insulation thickness: 150 mm, workpiece width (max.): 800 mm, The continuous system consists of the following components: Chemical pre-treatment by spraying Dryer Powder coating system Powder curing oven Conveying technology (cycle process) Njdpfjum Ufljx Alaecw Electrical control system

Year of construction: 2007, condition: good (used), MAKE - LVD, Made in USA/BELGIUM MODEL - GLOBAL 20 1225 YEAR - 2007 CONTROL - FANUC 180I - PB CAPACITY - 20 Tons THROAT DEPTH - 1250.0 mm SHEET SIZE MAX. - 2500.0 x 1250.0 mm (1250.0 x 5000.0 mm) MAXIMUM WORK PIECE WEIGHT - 150 Kg MAXIMUM MATERIAL THICKNESS - 6.0 mm MAXIMUM TABLE SPEED - 0 – 4330.0 TURRET - 30 STATIONS, 4 AUTO-INDEXING MAXIMUM PUNCHING DIAMETER - 89.0 mm PUNCHING SPEED - 350 STROKES/MIN NIBBLING SPEED - 900 STROKES/MIN Ncedpfsiab Epox Alaew PRESS MOTOR POWER RATING - 460V 3 Phase Motor DIMENSIONS - 5560.0 x 5560.0 x 2400.0 mm WEIGHT - 16,000 Kg PLUS BRUSH TABLE VERY LOW HOURS GOOD RANGE OF TOOLING