Second-hand machinery for sale (2,371)

Condition: good (used), Year of construction: 2008, operating hours: 25,662 h, Functionality: fully functional, machine/vehicle number: 17951, TECHNICAL DETAILS Control: MATSUURA G-Tech 30i (FANUC 30i MA) for 3-axis simultaneous machining X-axis travel: 660 mm Y-axis travel: 660 mm Z-axis travel: 660 mm Speed range: 40 - 12,000 rpm B-axis: 360° Dueln Hstwcvzsk Rrst Indexing increment: 0.001° Distance table surface - spindle nose: 80 to 680 mm Distance pallet surface - spindle center: 80 - 680 mm Distance pallet table center - spindle head: 120 - 720 mm Pallet size: 500 x 500 mm max. table load: 400 kg Max. workpiece size: Ø 650 mm x 750 mm Table surface: 40 holes â M16 x 2 mm pitch Pallet change time: 7.5 s Pallet change time (pallet to pallet): 15 s Number of pallets: 2 Number of magazine positions: 120 Tool diameter: with full occupancy Ø90 mm Tool diameter: with free neighboring stations Ø150 mm Tool length: 350 mm Tool change time (tool weight < 5 kg): 1.3 s Tool change time (tool weight > 5 kg): 2 s Chip-to-chip time (tool weight < 5 kg): 2.9 s Spindle holder with face contact: BT 40 JIS B 6339 Big+ Pull stud: BT 40 JIS B 6339 40P Inner diameter of the spindle bearing: 80 mm Spindle motor power (30%/100% ED): 22 / 15 kW Max. Torque (FANUC motor): 187 Nm up to 1,120 rpm Rapid traverse X-, Y- and Z-axis: 50 m/min Feed X-, Y- and Z-axis: 1 - 50,000 mm/min Stepless manual feed: 0 - 4,000 mm/min Positioning accuracy over the entire X-, Y- and Z-axis travel: ± 0.006 mm Repeat accuracy X-, Y- and Z-axis: ± 0.001 mm Changeover accuracy of different pallets in Y-axis: 0.01 mm Repeat accuracy of pallet clamping in X, Y and Z direction: 0.003 mm Indexing accuracy: 5" Repeatability of indexing: ± 2" Torque on table with FANUC drive: 380 Nm MACHINE DETAILS Dimensions: 3,340 x 6,740 x 2,533 mm Machine weight: 7,500 kg Total connected load: 51 kVA Supply voltage: 3 x 400V, 50 Hz Compressed air connection: 5.5 - 9.5 bar Compressed air consumption: max. 400 l/min Axle guides: Roller guides Lubrication: permanent grease lubrication X-, Y- and Z-axis power: 5.5/5.5/4.5 kW Axial force X-, Y- and Z-axis: FANUC motor 9.1/5.0/6.0 kN Acceleration/deceleration: 0.7 G EQUIPMENT - Preparation for magazine with 240 slots - Optical measuring system - Renishaw NC4 - RENISHAW OMP 60 measuring probe (EASY PROBE SOFTWARE included) - Measuring probe - Chip conveyor - Knoll high-pressure system - Extraction unit

Year of construction: 1998, Condition: good (used), Functionality: fully functional, TECHNICAL DETAILS x-way: 630 mm y-way: 630 mm z-way: 500 mm number of spindle revolutions: 0 - 15000 rpm pallet size: 500 x 500 mm b-axis: 360.000 x 0,001 ° tool holder: HSK 63 tool magazine: 41 MACHINE DETAILS machine weight: approx. 15 t spindle drive: 32 kW Duoloi T Ea Ren Hk Rrjt

Condition: ready for operation (used), Year of construction: 2005, Functionality: fully functional, machine/vehicle number: 97199/15202, spindle speed (max.): 7,000 rpm, spindle speed (min.): 2,000 rpm, grinding wheel diameter: 400 mm, grinding length: 20 mm, grinding diameter: 20 mm, TECHNICAL DETAILS Collet chuck holder: 1 - 10 mm Max. Workpiece diameter: 20 mm Min. workpiece diameter: 1 mm Dsln Heuyh Sysk Rrjut Grinding capacities Max. Sanding diameter: 20 mm Max. sanding length: 20 mm Grinding wheel Grinding wheel diameter (min.): 300 mm Grinding wheel diameter (max.): 400 mm Grinding wheel speed: 2,000 - 7,000 rpm MACHINE DETAILS Weight of the machine: 950 kg Dimensions: 1,200 x 2,100 mm Drive power Drive power grinding spindle: 1.2 - 5 kW Main spindle drive motor: 1.1 kW Hydraulic drive motor: 0.18 kW Coolant drive motor: 0.30 kW Total power consumption: 3 - 6.5 kW Note: Machine is set up but not connected & can be inspected under power on request

Condition: ready for operation (used), Year of construction: 2003, Functionality: fully functional, machine/vehicle number: 14400/02, center height: 200 mm, grinding length: 500 mm, grinding diameter: 600 mm, grinding wheel width: 30 mm, Application: Fully automated external and face grinding of synchronizer rings TECHNICAL DETAILS Control name: SIEMENS 840D Grinding length: 500 mm Center height: 200 mm Grinding wheel Grinding wheel arrangement: right, 30° inclined Grinding wheel dimensions: 600 x 30 x 203.2 mm Drive power: 7 kW Drive and movement X/Z-axis drive: ball screw drive Traversing speed: 0.01 - 10,000 mm/min Resolution: 1 µm Concentricity Workpiece spindle concentricity: < 1 µm MACHINE DETAILS Total power requirement: 7 kW Machine weight: approx. 7 t Workpiece changing system: Fanuc robot EQUIPMENT - Fanuc robot for workpiece change - Ball screw drive for X/Z axis Dueln Hkeuyh Ine Rrot Note: Machine is set up but not connected & can be inspected under power on request

Condition: ready for operation (used), Year of construction: 2005, Functionality: fully functional, machine/vehicle number: 0250164, grinding length: 400 mm, workpiece weight between centers: 250 g, spindle speed (max.): 2,938 rpm, TECHNICAL DETAILS Sanding capacities Swing diameter: 250 mm Rotation diameter in open setting block: 5 - 80 mm Orbital diameter in closed setting block: 10 - 80 mm Center width: 400 mm Minimum diameter, machinable with worn grinding wheel (Ø 280 mm): with orbital diameter of 250 mm: 0 mm Workhead and tailstock Workhead swivel: 90° Chuck diameter: 80, 125, 160, 200 mm Front work spindle end: ISO 702/1-1992 A2-3 Taper in the work spindle: ISO 296-1991 Morse 5 Taper in the tailstock quill: ISO 296-1991 Morse 4 Stroke of the tailstock quill: 50 mm Tailstock clamping force: 0 - 1,300 ± 85 N Grinding headstock Headstock swivel: +45° / -15° Total adjustability: 300 mm Rapid feed speed: 2,000 - 7,000 mm/min Grinding wheel Dimensions (diameter x width x hole): 450 x 66 x 127 mm Diameter after wear: 280 mm Maximum wheel width: 66 mm Table Table feed per 1 handwheel rotation: 1 mm Minimum feed: 0.001 mm Maximum feed with a center distance of 400 mm: 750 mm Work feed speed (selectable): 0.01 - 3,000 mm/min Rapid feed speed: 2,000 - 7,000 mm/min Weight of the workpiece Maximum weight in tips: 250 kg Flying incl. tool clamp: 50 kg Speed Grinding spindle speed levels: 2 Grinding spindle speed: 2,387 / 2,938 rpm Maximum peripheral speed of the grinding wheel: 50 m/s Grinding spindle speed at 33 m/s: 1,630 rpm Doln Hkouyh Afs Rrjut Machine weight: approx. 4.1 t Note: Machine is set up but not connected & can be inspected under power on request

Condition: ready for operation (used), Year of construction: 1999, Functionality: fully functional, machine/vehicle number: 28634, wheel diameter: 200 mm, controller manufacturer: Siemens, controller model: Sinumeric 840 C, module thread tooth pitch (max.): 3, module thread tooth pitch (min.): 0.5, Machine from prototype production - without automation TECHNICAL DETAILS Control: Siemens Sinumeric 840 C Wheel diameter: max.200 mm Wheel width: 250 mm Duelet Hkk Rsn Hk Rrst Module: 0.5 - 3 MACHINE DETAILS Total power requirement: 45 kW Supply voltage: 400 V / 50 Hz Machine weight: approx. 8.5 t Space requirement: approx. 4.4 x 2.4 x 2.7 m

Condition: ready for operation (used), Year of construction: 1998, Functionality: fully functional, machine/vehicle number: 1924, grinding wheel diameter: 450 mm, rotational speed (max.): 3,000 rpm, controller manufacturer: OSAI, controller model: 10 Series, grinding length: 2,710 mm, TECHNICAL DETAILS Control unit: OSAI 10 Series Sanding diameter: 250 mm Sanding length: 2710 mm Wheel diameter: max. 450 mm Spindle drives: Arena Siemens Programming distance: 0.001 - 500 mm Spindle speed: 3,000 rpm X-axis: workpiece rotation 0 - 360° Y-axis: bed slide -180 mm a + 2 mm Z-axis: longitudinal slide -10 mm a + 2390 mm W-axis: Grinding wheel cleaning -90° a + 90° MACHINE DETAILS Total power requirement: 45 kW Supply voltage: 3x400 V, 50 Hz Machine weight: approx. 15 t Space requirement L x W x H: 7.1 x 4.7 x 2.7 m Air pressure: 6 bar Air consumption: 30 l/h Duoln Hk Ret Hhhasrot Control cabinet dimensions: 1800 x 800 x 2000 mm Switch cabinet weight: approx. 1.5 t The machine does not have a module for worm grinding, but an incline.

Condition: ready for operation (used), Year of construction: 2003, Functionality: fully functional, machine/vehicle number: 76003, grinding wheel diameter: 275 mm, gear diameter: 150 mm, module thread tooth pitch (max.): 3, module thread tooth pitch (min.): 1, With automated loading of the Felsomat machine TECHNICAL DETAILS Control system: Siemens 840D / Reishauer VM24RZ Wheel diameter: max. 150 mm Module: 1 - 3 pieces grinding wheel diameter: 206 - 275 mm MACHINE DETAILS Machine weight: approx. 7.2 t Space requirement: approx. 2.44 x 1.43 x 2.46 m Rated power: 36 kVA Duoln Hjt Hg Dyok Rrst Mains voltage: 3x400 V, 50 Hz No twist control grinding option

Condition: ready for operation (used), Year of construction: 2002, Functionality: fully functional, machine/vehicle number: 11045534554, travel distance X-axis: 500 mm, travel distance Y-axis: 420 mm, travel distance Z-axis: 380 mm, controller manufacturer: Siemens, controller model: Sinumerik 840 D, spindle speed (max.): 18,000 rpm, TECHNICAL DETAILS x-path: 500 mm y-path: 420 mm z-path: 380 mm Control system: Siemens 840 D Tool holder: HSK 63 Spindle speed: 18,000 rpm Magazine places: 32 pieces Tool length: 280 mm Djlnot Hgyuj Hk Rrjut Tool weight: max. 6 kg Feed rate: 20,000 mm/min Rapid traverse: 50 m/min Input unit: 0.01 mm Position measuring system Resolution: 0.001 mm Position tolerance: 0.010 mm MACHINE DETAILS Machine weight: approx. 5.5 t Installation dimensions: 5400 x 6800 x 2584 mm Transport dimensions: 2295 x 2683 x 2436 mm

Condition: ready for operation (used), Year of construction: 2002, Functionality: fully functional, travel distance X-axis: 630 mm, travel distance Y-axis: 560 mm, travel distance Z-axis: 560 mm, spindle speed (max.): 18,000 rpm, number of slots in tool magazine: 24, TECHNICAL DETAILS Control name: Heidenhain TNC 426/430 X-path: 630 mm Y-path: 560 mm Z-path: 560 mm Number of axes: 5 Spindle and tool Spindle speed: 18,000 rpm Tool holder: SK 40 Number of tool positions in the magazine: 24 Tool diameter magazine 1/2: 130 mm / 80 mm Max. Tool length: 315 mm Max. Tool weight: 8 kg Feed and rapid traverse Rapid traverse X/Y: 26 m/min Rapid traverse Z: 20 m/min Feed XYZ: 10,000 mm/min Table Table dimensions: 1,000 x 600 mm Distance T-slots: 63 mm Number / size of T-slots: 9 / 14H7 MACHINE DETAILS Duelsuyizvon Hk Rret Machine weight: approx. 6.5 t Installation dimensions: 5,400 x 4,400 x 2,847 mm Installation weight: 7.6 t Transport dimensions: 3,500 x 2,700 x 2,220 mm Transport weight: 6.7 t Additional equipment Rotary table and B-axis Note: Machine is set up but not connected & can be inspected under power on request

Condition: ready for operation (used), Year of construction: 2019, operating hours: 9,680 h, Functionality: fully functional, turning diameter: 170 mm, travel distance X-axis: 160 mm, travel distance Z-axis: 310 mm, rotational speed (max.): 6,300 rpm, center width: 600 mm, TECHNICAL DETAILS Travel in X/Y/Z: 160 mm / - / 310 mm max. rod passage: DN 45 mm max. turning diameter: 170 mm Swing diameter over bed: 430 mm Center distance: 600 mm (spindle nose - center point) Main spindle max. speed: 0 - 6,300 rpm max. drive power: 11 kW max. torque: 70 Nm C-axis: available Tool turret Number of tool positions: 12 Driven tools: 6 max. speed: 0 - 5,000 rpm max. drive power: 4 kW Deln Hkovbzr Eo Rrsut max. torque: 16 Nm MACHINE DETAILS Machine switched on: 33,250 h Ready for operation / automatic: 30,652 h Production mode: 9,680 h Workpiece counter: 400,014 pieces Machine dimensions: 2,250 x 1,675 x 1,940 mm Bar feeder dimensions: 5,800 x 550 x 1,500 mm Weight: 3,300 kg EQUIPMENT - C-axis and tailstock - Tool turret with 12 positions, 6 of which are driven - Bar loader LNS 6.26 HS 4.4 (year of manufacture 2019) - Large tool package

Condition: excellent (used), Year of construction: 2004, Functionality: fully functional, machine/vehicle number: 34938, cutting length (max.): 4,300 mm, cutting height (max.): 2,200 mm, cutting depth: 80 mm, rotational speed (max.): 4,750 rpm, TECHNICAL DETAILS Swivel adjustment: 0 - 90° (manual) Cutting area: 4300 x 2200 x 80 mm Speed: 4750 rpm Feed: manual Design: automatically deflecting slatted frame Saw carriage lock: manual Saw unit immersion: manual MACHINE DETAILS Motor power : 4,4 kW Delnsub Tr Ej Hk Rrsut Space requirement L x H x W: 5400 x 2900 x 1600 mm Type of installation: wall-mounted or free-standing

Condition: ready for operation (used), Year of construction: 2013, Functionality: fully functional, machine/vehicle number: 97128, travel distance X-axis: 625 mm, travel distance Y-axis: 100 mm, travel distance Z-axis: 250 mm, spindle speed (max.): 5,500 rpm, turning diameter: 250 mm, turning height: 200 mm, clamping diameter: 315 mm, TECHNICAL DETAILS Control: Siemens 840 D turning diameter: 250 mm Rotation diameter: 250 mm Turning height: 200 mm Chuck diameter: 315 mm Dsln Hk Rsuyi Icsreut Travel distance X-travel: 625 mm Y-travel: +100 / -80 mm Z-travel: 250 mm Spindle Spindle speed (max.): 5,500 rpm Drive power of the synchronous spindle: 37.7 kW Max. Torque: 300 Nm Tool system Tool system: VDI 30 + 40 Machine bed Material: Hydropol (special concrete and steel) Typical components: Ball cages, ball hubs, gear wheels, sliding sleeves, pump wheels, flanges, synchronizer rings, bearing rings, joint journals, MACHINE DETAILS Machine weight: approx. 8 tons Total power requirement: 37.7 kW Note: Machine is set up but not connected & can be inspected under power on request

Condition: ready for operation (used), Year of construction: 2004, Functionality: fully functional, spindle speed (min.): 120 rpm, spindle speed (max.): 1,275 rpm, lifting speed: 25 mm/s, feed length Z-axis: 500 mm, hone diameter: 56 mm, TECHNICAL DETAILS Control: Siemens PLC control S7, NAGEL honing spindle control MS-U3 Production capacity: 90 workpieces/h at 100 % capacity utilization Roundness: 0.006 mm / 0.012 mm Bore tolerance: 22.018 - 22.028 mm / 56.000 - 56.019 mm Surface roughness (Rz): 4 µm / 6.3 µm Honing time: 28 / 33 seconds Secondary time: 12 / 7 seconds Cycle time: 40 seconds Workpiece Type: Connecting rod, large and small eye Hardness: 100 - 130 HB Machining diameter: 22 - 26 mm Machining length: 20.8 - 20.23 mm Workpiece holder: clamped and held down Machining data Duelouyidksn Hk Rret Pre-machining: fine-turned Diameter: 21.99 - 22.01 mm / 55.95 - 55.99 mm Roundness: 0.007 mm / 0.01 mm Surface roughness (Ra): 6 - 8 / 8 - 12 µm Material allowance: 0.013 - 0.033 mm / 0.02 - 0.06 mm Tool type Tool type: Diamond, articulated rod Honing spindle Number of honing spindles: 2 Stroke length: 0 - 500 mm Stroke speed: 25 m/min (infinitely variable) Tool holder: top / bottom, infinitely adjustable Spindle speed: 425 - 1,275 rpm and 120 - 360 rpm Drive power Stroke drive power: 5.5 kW Spindle drive power: 3 kW / 4 kW Measuring technology Measuring system: electro-mechanical step expansion Air measuring device: 0.0005 - 0.08 mm MACHINE DETAILS Installation area / height: 6,200 x 3,900 / 4,300 mm Weight: approx. 8 t Color: machine light grey RAL 7035, control cabinet capri blue RAL 5019 Construction: Welded steel construction in panel construction. The uprights have been artificially aged to relieve stresses. Hydraulic equipment Hydraulic tank: 400 l Electrical equipment Operating voltage: 400 V, 50 Hz with neutral conductor Control voltage: DC 24 V Total connected load: 28 kW Standard: according to VDE 0113 Note: Machine is set up but not connected & can be inspected under power on request

Year of construction: 1996, operating hours: 91,897 h, Condition: ready for operation (used), Functionality: fully functional, machine/vehicle number: 288, TECHNICAL DETAILS x-way: 600 mm y-way: 560 mm z-way: 560 mm Djln Hslruxfjk Rrjut Control: Siemens MACHINE DETAILS supply voltage: 400 V / 3 phases / 50 Hz Connected load: 60 kVA total power requirement: 12 kW Machine weight: approx. 10 t EQUIPMENT - 2 machine pallets - 1 probe

Year of construction: 2003, operating hours: 33,792 h, Condition: good (used), Functionality: fully functional, machine/vehicle number: 28840003282, TECHNICAL DETAILS x-way: 800 mm y-way: 710 mm z-way: 710 mm B-axis: 360 Control: Siemens Sinumerik 840D number of pallets: 2 pallet size: 500 x 630 mm tool diameter: max. 120 mm tool holder: SK 50 Magazine: chain magazine with 62/90 places MACHINE DETAILS Dueln Holruquok Rret Machine weight: approx. 12.5 t (transport weight) height: 3,2 m space requirement: 6,0 x 6,5 m Rated power: 80 kVA Rated current: 120 A Operating voltage: 400 V / 50 Hz Compressed air: 6 bar

Year of construction: 2000, operating hours: 47,085 h, Condition: good (used), Functionality: fully functional, machine/vehicle number: 42272, Machining center with 5 pallets TECHNICAL DETAILS x-way: 600 mm y-way: 560 mm Duoln Hkjlrupas Rrot z-way: 560 mm B-axis (table): 360° tool holder: SK 40 pallet size: 5 x 500x400 mm Control: Siemens 840D MACHINE DETAILS supply voltage: 300 V / 3 phases / 50 Hz Power: 60 kVA

Year of construction: 1989, Condition: ready for operation (used), Functionality: fully functional, machine/vehicle number: 5117.19, TECHNICAL DETAILS grinding diameter: 450 mm grinding length: 1600 mm center height: 225 mm control name: Siemens Sinumerik System3 speed: max. 2440 rpm center distance: 1750 mm resolution: 0,001 mm speed: 0,06 - 10000 mm/min cross slide: 180 mm feed rate: 0,01 - 5000 mm/min resolution: 0,0005 mm workpiece weight: max. 500 kg quill travel: 40 mm Straightness of surface line over 650 mm: 0.004 mm Delnslnkfao Hk Rrout Roundness accuracy: 0.0005 mm MACHINE DETAILS Machine weight: approx. 7.3 t total connected load: max. 22 kVA

Year of construction: 1996, Condition: good (used), Functionality: fully functional, machine/vehicle number: 009005005, TECHNICAL DETAILS working range: 2 - 200 mm bar length: 500 mm dressing speed: 500 rpm control: Siemens 840 C control wheel width: 400 mm control wheel bore: 152 mm regulating wheel diameter: 350 mm control wheel speed: 10-150 rpm Control wheel drive: 11,3 kW grinding wheel width: max. 400 mm grinding wheel diameter: max. 660 mm grinding wheel bore diameter: 304.8 mm grinding wheel speed: 63 m/s Grinding wheel drive: 45 kW MACHINE DETAILS weight: 10 t Connection: 400 V / 50 Hz / 3 phases Duoln Hk Relmm Evjrst Rated power: 115 kW

Year of construction: 1994, Condition: good (used), Functionality: fully functional, machine/vehicle number: 073000312, TECHNICAL DETAILS grinding diameter: max. 200 mm regulating wheel width: 400 mm grinding wheel width: max. 400 mm Control name: Siemens 840 C Profile depth: max. 15 mm Gr. workpiece length plunge grinding: 500 mm drive grinding spindle: 50 kW regulating wheel speed: 10 - 150 1/min regulating wheel drive: 3 kW regulating wheel inclination: +2° / -6 ° peripheral speed: 31,5 / 63 m/sec MACHINE DETAILS machine weight: approx.10 t operating voltage: 400 V / 3 phases / 50 Hz rated current: 160 A Deln Hkolmmy Uj Rrsut

Condition: ready for operation (used), Year of construction: 2007, Functionality: fully functional, machine/vehicle number: H-V12319, travel distance X-axis: 660 mm, travel distance Y-axis: 356 mm, travel distance Z-axis: 456 mm, spindle speed (max.): 10,000 rpm, number of slots in tool magazine: 20, TECHNICAL DETAILS Control system: ULTIMAX 4 X travel: 660 mm Y travel: 356 mm Z travel: 456 mm Spindle speed range: 10 - 10,000 rpm Table dimensions: 762 x 356 mm Tool changer: 20-fold Dujln Hk Rsuiytxorjt Spindle holder: SK40 Rapid traverse X/Y/Z: 28 m/min MACHINE DETAILS Drive power: 11 kW Space requirement (L x W x H): 2,000 x 1,800 x 2,600 mm Weight: approx. 2,900 kg

Year of construction: 2002, Condition: good (used), Functionality: fully functional, 3 Main spindle with 70mm bar passage FUNCTIONS The raw bar is machined in spindle 1 and 2 with a 12-position star turret. At the same time, a 2-station front turret can work on this spindle (for drilling or internal boring). After machining, the drum cycles. The pre-turned part is finished in spindle 3 with a 12-position star turret and tapped. The part is then finished in the counter spindle and unloaded by the unloading gripper (monitoring available). The bar is retracted and the drum cycles. TECHNICAL DETAILS Bar passage: 70 mm counter spindle tool turret: 5 pieces, VDI30 (CNC cross slide) High pressure internal cooling: two turrets Measuring system: direct, high resolution in all X-axes Control system: Siemens 840 D Powerline tool monitoring: Artis Collet chuck: 4x Hainbuch SK65 Number of parallel tools: 5 Main spindle 1: Roughing of the turned part Tool holder: star turret with 12 positions Other: Possibility for additional work by 2-fold frontal turret Main spindle 2: Finishing of the turned part Tool holder: 12-position star turret Other: Possibility for finishing by 2-fold frontal turret Main spindle 3: Finishing, parting and backworking of the turned part Tool holder: star turret with 12 positions Doljn Uum Hen Hk Rrout EQUIPMENT Bar feeder for 1500mm long bars

Condition: good (used), Year of construction: 2006, operating hours: 48,000 h, Functionality: fully functional, machine/vehicle number: A0230A1295, laser power: 5,000 W, sheet thickness aluminum (max.): 12 mm, sheet thickness steel (max.): 25 mm, No minimum selling price - guaranteed knockdown to the highest bid! TECHNICAL DETAILS Make: TRUMPF Type: Trumatic L 3050 - 5 kW Dolneu R Sa Ae Hk Rrsut Year of manufacture: 2006 Working range X-axis: 3,000 mm Y-axis: 1,500 mm Z-axis: 115 mm Control system Type: Siemens Sinumerik 840 D Laser power Laser power: 5,000 W Max. Sheet thickness: Mild steel 25 mm Max. Sheet thickness: Stainless steel 20 mm Max. Sheet thickness: aluminum 12 mm Operating hours Operating hours: approx. 48,000 hours EQUIPMENT Closed machine frame with integrated laser unit Laser unit: TLF 5000 CO₂ laser, high-frequency excited, cooling unit, logbook function Automatic pallet changer Longitudinal conveyor belt for small parts/waste Drives: Gantry drive in combination with linear direct drives Laser power control HI-LAS high-pressure cutting Plasma sensor system (PMS) Fast processing with SprintLas ContourLas for the production of small holes Programmable power cycles Microweld Programmable cutting gas pressure setting Laser cutting head with 5" lens and laser cutting head with 7.5" lens Quick-change cutting head device Automatic sheet outer edge detection Capacitive height control (DIAS) Process Control System (PCS) Position laser diode Automatic switch-off Work area lighting SIN 840D control system: Open control system on PC basis, simple operation, online help, diagnostic functions, maintenance logbook, technology data, teleservice Workshop programming ToPs 100 lite Safety and security Multi-beam light barriers Beam guidance completely encapsulated and ventilated with nitrogen Monitoring system Multi-chamber extraction and compact dust extractor Protective cabin Network connection BNC/RJ-45 network connection Electrical equipment Voltage: Three-phase current 400 V / 50 Hz EXTENDED EQUIPMENT Liftmaster included

Condition: good (used), Year of construction: 1998, Functionality: fully functional, machine/vehicle number: 700002, punching force: 18 t, sheet thickness (max.): 6 mm, travel distance X-axis: 1,275 mm, travel distance Y-axis: 2,030 mm, punching diameter: 76 mm, table load: 75 kg, No reserve price - guaranteed sale at the highest bid - Attractive price due to lack of space for new machine! Submitting a bid obliges you to pick up the machine on time in week 3 - 2025 (January 13th, 2025 - January 18th, 2025). TECHNICAL DETAILS Working area Working area (X x Y): 1,275 x 1,280 mm Extended working area with additional tables: 1,275 x 2,030 mm Performance Max. sheet thickness: 6.4 mm Max. punching force: 180 kN Max. workpiece weight: 75 kg Max. clearance height: 38 mm Programmable hold-down force: 400 - 1,700 kN Speeds X-axis: 90 m/min Y-axis: 60 m/min Simultaneous (X and Y): 108 m/min Punching stroke sequence (step width 1 mm): 900 1/min Punching stroke sequence (step width 25 mm): 420 1/min Signing and fast beading stroke sequence: 2,200 1/min C-axis: 3 revolutions/s Tools Linear magazine: 9 tools Number when using multitool (2 clamps): 9 - 90 tools Rotation of all tools: 360° Tool change time Single tool: approx. 3.5 s Multitool: approx. 0.9 s Max. stand diameter single stroke: 76 mm Max. stand diameter standard multicut: 200 mm Programmable part chute Max. part size: 200 x 200 mm Sortable in: 2 containers Accuracy Position deviation: ± 0.1 mm Average position spread: ± 0.03 mm TRUMPF CNC control Base: Bosch Type3 Color monitor: 10.4" Hard disk storage: 300 MB for NC programs Floppy disk drive: 3.5" Platform: PC Pentium with Windows NT Workshop programming: ToPs 2000 Safety Safety light barrier system: Two-beam light barrier MACHINE DETAILS Electrical connection: 17 kVA Electrical energy: approx. 8 kW Pneumatic connection: 7-14 bar Compressed air consumption: 8 Nm³/h Dimensions and weights Dslnsvl E Tne Hk Rrsut Space requirement (including light barrier): 410 x 5,700 mm Height: 2,255 mm Height with hood open: 2,505 mm Weight: 8,000 kg

Condition: ready for operation (used), Year of construction: 2007, operating hours: 26,073 h, Functionality: fully functional, laser power: 4,000 W, sheet thickness aluminum (max.): 10 mm, sheet thickness steel (max.): 20 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, TECHNICAL DETAILS Travel X / Y / Z: 3000 / 1500 / 115 mm Workpiece weight: max. 900 kg Control: Sinumerik 840 D SL Laser source: TruFlow 4000 Power range: max. 4,000 W Dueln Hk Reucu Ttoret Wavelength: 10.6 µm Sheet thickness Al / stainless steel / mild steel: 10 / 15 / 20 mm Simultaneous speeds: 140 m/min Position deviation Pa: ±0.05 mm Position spread Ps: ±0.03 mm MACHINE DETAILS Dimensions: 9.3 x 4.6 x 2.2 m Weight: 12.0 t Connected load: 88 kVA Switch-on time: 47,377 h Cutting time: 26,073 h