LPG Forklifts

HC Hangcha CPYD35–XW22F

Condition: used, functionality: fully functional, Year of construction: 2020, operating hours: 1,815 h, load capacity: 3,500 kg, lifting height: 4,500 mm, free lift: 1,410 mm, mast type: triplex, construction height: 2,240 mm, fork carriage width: 1,100 mm, fork length: 1,500 mm, empty load weight: 4,995 kg, drive type: Treibgas, construction width: 1,235 mm, LPG forklift Load center of gravity: 500 Fork width: 120 mm Fork thickness: 50 mm ISO class: ISO class 3 = 2,500 - 4,999 kg Mast type: Triplex Transmission: Hydrodynamic Condition: Ready for use and fully functional Technical condition: Very good Front tires Type: Superelastic Front tires Size: 8.15-15 Front tires Condition: 20 - 40% Rear tires Type: Superelastic Rear tires Size: 6.50-10 Hfedpfxst Dd Azj Ad Dsp Rear tires Condition: 60 - 80% Description: Half cab with PVC side panels, lighting similar to STVO, 3rd + 4th valve up to fork carriage, rotating beacon, hand lever, interior mirror sideshift, fork positioner, ATIB fork positioner with sideshift, opening range: IK- IK 145- 850 mm 3rd valve, 4th valve, rear working lights, front working lights, half cab, interior mirror, rotating beacon, windshield wiper, LED, seat,

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. Hfodpfx Aokcgf Hed Dop The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: used, Year of construction: 2020, operating hours: 1,203 h, load capacity: 3,500 kg, lifting height: 4,500 mm, free lift: 1,410 mm, mast type: triplex, construction height: 2,240 mm, fork carriage width: 1,100 mm, fork length: 1,500 mm, empty load weight: 4,995 kg, drive type: Treibgas, construction width: 1,245 mm, LPG forklift Load center of gravity: 500 Fork width: 120 mm Fork thickness: 50 mm ISO class: ISO class 3 = 2,500 - 4,999 kg Mast type: Triplex Transmission: Hydrodynamic Condition: Ready for use and fully functional Technical condition: Very good Front tires Type: Superelastic Hfodpfjt Dd Abox Ad Dsp Front tires Size: 8.15-15 Front tires Condition: 40 - 60% Rear tires Type: Superelastic Rear tires Size: 6.50-10 Rear tires Condition: 60 - 80% Description: Half cab with PVC side panels, lighting similar to STVO, 3rd + 4th valve up to fork carriage, rear work lights, rotating beacon, hand lever sideshift, fork positioner, Fork positioner with sideshift, opening range: IK- IK 145- 860 mm 3rd valve, 4th valve, rear work lights, front work lights, half cab, interior mirror, rotating beacon, windshield wiper, LED, seat,

Year of construction: 2023, condition: new, functionality: fully functional, New Astronergy 420W TopCon Photovoltaic Panels, maximum efficiency, 12-year product warranty and 30-year production warranty (87% after 30 years). 20 pallets of 36 panels available: -17 pallets (36 panels per pallet) in the San Pietro Mosezzo (Novara) warehouse -3 pallets in the warehouse in Nereto (Teramo) Hfodpfxjupvxxs Ad Dep

Condition: used, Year of construction: 2009, operating hours: 20,536 h, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, empty load weight: 16,000 kg, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 20,536 hours, as of September 2024 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Hfedpfx Aeu Thypod Djp Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine is currently in our workshop undergoing partial refurbishment. We expect the refurbishment work on the machine to be completed by the end of October, after which the machine will be tested and released for sale.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: Hfodjvwlqqjpfx Ad Djp The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Hours 43.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Hjdpfx Adokcgyns Djfp Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Hfjdpfotvat Tox Ad Dsp After refurbishment, this baler is sold with a 2-year warranty.

Condition: new, functionality: fully functional, Year of construction: 2025, bending force (max.): 1,000 t, stroke length: 200 mm, operating speed: 50 mm/s, reverse speed: 180 mm/s, overall weight: 8,000 kg, total length: 3,915 mm, total width: 1,605 mm, total height: 2,655 mm, input voltage: 380 V, input frequency: 50 Hz, warranty duration: 24 months, bending angle (max.): 90 °, table length: 3,200 mm, working height: 450 mm, All-Electric Servo Bending Machine Nominal force(KN): 1000 Slider stroke(mm): 200 Throat depth (mm): 360 X-axistravel(mm): 600 R-axistravel(mm): 200 Z-axistravel(mm): 2500 🔹 Smart CNC System – SL100-P with high-end algorithms and 12-inch touchscreen for intuitive operation. Hfjdpfxov Hchls Ad Djp 🔹 High-Precision Structure – Finite element analysis (FEA), annealed, and one-time machining for long-term stability and accuracy. 🔹 4-Axis Intelligent Backgauge – AC servo-driven, high-speed positioning with automatic collision avoidance. 🔹 Precision Compensation System – Adjustable convex strips & fine-tuning mechanism for optimal bending accuracy. 🔹 Powerful & Durable Drive – High-torque servo motor, heavy-duty ball screws & sealed protection for longevity. 🔹 Fully Closed-Loop Control – Y1/Y2 magnetic scale feedback, positioning accuracy ±5μm. 🔹 Optimized Electrical System – Closed electrical box, heat dissipation, & neat wiring for reliability and easy maintenance. 🔹 Imported Precision Components – Ball screws & linear guides ensure accuracy without stroke compensation. 🔹 High precision, stability, and smart automation – designed for professional sheet metal bending!

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Hfedjtvau Ajpfx Ad Dep Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.