Water filling machine

Krones

Condition: used, Year of construction: 2007, Overview This Krones Variojet is a rotary rinser for glass bottles, built in 2007 and still running in production at a large brewery. The bottles are held in grippers on the carousel and pass three treatment stages before filling: rinsing with water, blowing out with air and gravity drainage. The machine runs at up to 48,000 bottles per hour; this output was achieved in production on the 330, 400 and 500 ml formats, while on the larger formats the filler set the line speed. It has been run on 330, 400, 500, 580 and 650 ml glass bottles, and the change parts for these formats are included. The rinser is fully enclosed by transparent safety doors and is operated from a Krones iPanel. The universal format parts visible in the video are not included in the offer. Technical data - Manufacturer: Krones - Model: Variojet - Year of manufacture: 2007 - Machine type: rotary rinser for glass bottles - Output: up to 48,000 bottles per hour - Bottle formats: 330, 400, 500, 580 and 650 ml glass - Rinsing positions: 110 - Treatment stages: water rinsing, air blowing, gravity drainage - Control: Siemens S7-300 PLC, Krones iPanel (B&R) with zenon V6.20 - Electrical supply: 400/230 V, 50 Hz, 3/N/PE, full-load current 18 A - Operating hours: 44,485 h - Dimensions: approx. 4.5 m across the carousel including the safety guarding Equipment - Rinser with carousel, bottle grippers and transparent safety doors Hedpfoz Hai Tsx Afusu - Front table with infeed screw and starwheels - Control panel with Krones iPanel - Water and air supply manifold - Domnick Hunter compressed-air dryer - Change parts for 330, 400, 500, 580 and 650 ml bottles - Water drip trays Condition Used, in good condition with no known defects. The machine is still installed and in production and can be inspected in operation by arrangement. Maintenance: the drive train is overhauled every two years (last in 2025), the rinsing nozzle system every two years (last in January 2026) and the water and air distributor every two years (last in 2024); suspension and format components are inspected monthly and repaired as needed. Availability Available from late February / March 2027, after removal from the production line. Location: Poland.

Condition: used, Glass bottle filling system for hot filling smoothies. Consisting of the following components: - Unpacking table - bottle rinser - Vacuum filler (with 24 filling valves, Nagema, 1984, type ‘VW 24/1’) - Flash pasteuriser (KZE) - Pressure tank - Capper (Marchesini, type "ML667") - Lid sorter - Tunnel cooler - Blower - Lid inspection (BBull CIS) - Labeller (Anker, 1999, type ‘Roland 10/4’) - Packing table - Conveyors - Control panel - Cooling tower - Steam boiler - Water softening (Lohbeck GmbH, Softtrol CD double system) Additional title: hot filling, with pasteurisation Hedpfx Afowgc R Eoueu Capacity: 5000 bo/h Formats: 0.25 liter bottles, twist off caps Features: Unpacking table, rinser, vacuum filler, flash pasteuriser, pressure tank, capper, lid sorter, tunnel cooler, lid blow-off, lid inspection, labeller, packing table, conveyors, control panel, cooling tower, steam boiler

Condition: used, Year of construction: 2019, Overview This Krones VarioFlash B is a flash pasteurization system for beer and beer mix beverages, built in 2019 by Krones AG at its Steinecker plant in Freising, Germany. It pasteurizes 20 - 45 hl/h in a three-stage plate heat exchanger with energy recovery, a heat retention tube and a cooling stage. Everything is mounted on a stainless steel skid with a horizontal 2,100 l buffer tank, and a freestanding stainless steel control cabinet with touchscreen HMI completes the system. Technical data - Manufacturer: Krones AG (Werk Steinecker, Freising, Germany) - Model: VarioFlash B with cooling stage - Year of manufacture: 2019 - Machine type: flash pasteurizer with plate heat exchanger - Products: beer, beer mix beverages - Capacity: 20 - 45 hl/h - Pasteurization temperature: 71 - 85 °C - Holding time: 30 s at 45 hl/h - Max. CO₂ content: 6.5 g/l - Product inlet temperature: 5 - 15 °C; product outlet temperature: 16 °C - Energy recovery: approx. 91 % - Heating requirement at 85 °C: approx. 51 kW (approx. 90 kg/h steam at 6 bar(g), 165 °C) - Cooling requirement with water circulation at 5 °C: approx. 38 kW (5 m³/h glycol water, 2 - 10 °C) - Process water: inlet pressure 4.0 bar(g), inlet temperature 6 - 15 °C - Buffer tank: 2,100 l, max. allowable pressure -1.0 / +7.0 bar, allowable temperature -4 to +98 °C, CE marked Equipment - Plate heat exchanger with 3 stages: energy recovery, pasteurization with temperature control, cooling with temperature control - Heat retention tube with fixed length; PU control depending on temperature and flow rate - Hot water circuit with separate brazed plate heat exchanger, temperature control, circulation pump and expansion vessel - Sanitary product pumps: frequency-controlled product feed pump, booster pump for a positive pressure difference towards the unpasteurized product, frequency-controlled product pump to the filler Hsdpoz Ekdxefx Afuou - Horizontal stainless steel buffer tank, pneumatic valves, inline instrumentation and sanitary pipework on a tubular stainless steel frame - Freestanding stainless steel control cabinet with touchscreen HMI and main switch Condition Used. The system has been removed from production and is stored indoors. It can be inspected by appointment. Availability Immediately. Location: Germany.

Condition: used, Year of construction: 2012, Overview Complete Krones PET line from 2012 for carbonated water in non-returnable PET bottles of 0.5 L, 1.0 L and 1.5 L, rated at 16,000 bottles/h on the 1.5 L format. The line runs from preform feeding through a blow moulder-filler-capper bloc in a clean room, beverage treatment and CIP, inspection, drying, coding and wrap-around labelling, to shrink-film packing with handle application, palletizing and stretch wrapping. A separate sleeve section with sleeve labeller, steam shrink tunnel, inspection and two dryers is included. Technical data - Year of manufacture: 2012 - Output: 16,000 bottles/h (1.5 L) - Product: carbonated water - Bottles: PET, 0.5 L, 1.0 L and 1.5 L - Labeller: up to 20,000 bottles/h - Packer, palletizer and stretch wrapper: up to 24,000 bottles/h - Packs: shrink-film packs with carry handle, 3x2 and 4x3 - Pallets: 800 x 1200 mm and 1000 x 1200 mm - Electrical: 380/220 V, 3/N/PE, 50 Hz Scope of Delivery - Preform feed unit | Krones | CONTIFEED | with tilting device for the preform hopper | 2012 - Preform interior cleaning | Krones | PREJET | 2012 - Stretch blow moulder | Krones | CONTIFORM S8 | 16,000 bottles/h (1.5 L) | 2012 - Filler-capper | Krones | MODULFILL VFS | 60 filling valves, 16,000 bottles/h (1.5 L) | 2012 - Clean room | Krones | for the blow moulder-filler-capper bloc | 2012 - Closure conveyor | Krones | 2012 - Beverage treatment | Krones | CARBOFLOW | 2012 - CIP system | Krones | VARIOCLEAN | 30 m³/h | 2012 - Container conveyors | Krones | SYNCO | 2012 - Inspection machine | Krones | CHECKMAT 707 | 2012 - Container dryer | Krones | LINADRY | 2012 - Container coding | Videojet | inkjet coder | 2012 - Labelling machine | Krones | CONTIROLL COMBI | wrap-around OPP labels, up to 20,000 bottles/h | 2012 - Inspection machine | Krones | CHECKMAT 731 | 2012 - Sleeve labeller | Krones | SLEEVEMATIC | 2017 Hodpfez Dw Uusx Afusu - Steam shrink tunnel | Krones | SHRINKMAT - Inspection machine for the sleeve section | Krones | CHECKMAT - 2 container dryers for the sleeve section | Krones | LINADRY | 2017 - Pack conveyors | Krones | MULTICO | 2012 - Shrink-film packer | Krones | VARIOPAC PRO FS | 3x2 and 4x3 packs, up to 24,000 bottles/h | 2012 - Handle applicator | Krones | VARIOSTICK | 2012 - Palletizer | Krones | MODULPAL | 800 x 1200 and 1000 x 1200 mm pallets, up to 24,000 bottles/h | 2012 - Pallet conveyors | Krones | PALCO | 2012 - Stretch wrapper | Robopac | 2012 - Electrical power distribution for the line | Krones | 2012 Condition Dismantled and stored. Inspection on site by appointment. Availability Available immediately. Location: Georgia.

Condition: used, Year of construction: 1992, Automatic PET bottle blowing machine Manufacturer: SIDEL Hjdpswa Rhrjfx Afuou Type: SBO 4 S1 Year of prod. 1992 Capacity: 4,000 for 1.5 L / 2 L bottles Installed power: 150 kW Includes 1.5 L molds Preform feeder Technical condition: used machine, starts up, program is functional

Condition: used, Year of construction: 2003, functionality: fully functional, machine/vehicle number: K787016, overall weight: 41,000 kg, input voltage: 400 V, input frequency: 50 Hz, input current: 800 A, operating pressure: 40 bar, control voltage: 24 V, type of input current: three-phase, Equipment: documentation/manual, Krones Contiform S20 PET stretch blow molding machine – 20 cavities, output up to 40,000 units per hour. Used Krones Contiform S20 machine for manufacturing PET bottles. The machine is completely disassembled and prepared for loading onto a truck. Due to its disassembled condition, it is not possible to perform a test run or functional tests – it is sold as a complete set of components for reassembly by the buyer. Hodoz Euubspfx Afueu Technical specifications: • Manufacturer: Krones • Model / Year: Contiform S20 / [2003] • Number of cavities: 20 • Nominal output (according to the manufacturer's specifications): up to 40,000 bottles/hour • Maximum container volume: up to 3 l (depending on the shape) • Oven: linear, with a 40 mm stroke • Neck size: 26/22 (PCO 1881) Scope of supply: [preform feeder, hopper/elevator and orienting device, chiller, molds, spare parts, etc.] Inspection possible by prior arrangement – the machine can be inspected in its disassembled state, with the components laid out in Kutno. Loading at the buyer's expense. Transport to be agreed. Price on request.

Condition: excellent (used), Year of construction: 2003, PET bottle blowing machine Manufacturer: KRONES Model: CONTIFORM K781 Efficiency: 12,000 bph Includes 1.5 L and 0.5 L bottle molds Power: 150 kW Air requirement: 10 bar - 1500 m3/h, 30 bar - 1000 m3/h Set dimensions (blow mold + preform feeder): 1100 x 340 cm, h: 450 cm Blow mold dimensions: 500 x 340 cm, h: 250 cm Feeder dimensions: 600 x 250 cm, h: 450 cm Air requirement: 10 bar - 1500 m3/h, 30 bar - 1000 m3/h Year of production: 2003 Hsdpjvddkvsfx Afusu Technical documentation of machine operation Very good condition

Condition: ready for operation (used), Year of construction: 2019, Complete cup filling and sealing machine (year of manufacture 2019) with inkjet encoding, conveyor belt extension and dosing bar (incl. perlator inserts, year of manufacture 2020) used in the cheese industry. Filling temperature: Cold filling, round plastic bucket/plastic bucket/plastic bucket 2: Diameter 175mm x height 131mm/diameter 104mm x height 55mm or 65mm/diameter 227mm x height 194mm. Dimensions X/Y/Z and weight, without outfeed conveyor belt and shifting shank: 2200mm/2200mm/3200mm and approx. 3500kg. Hedpfsr Dd H Sex Afuju

Condition: used, Year of construction: 2020, Overview Krones Ergomodul modular container labeller. Containers run anticlockwise after the infeed in a frontal arrangement with two discharge starwheels. Finish RAL 9018 papyrus white in the wet-line section. Two docking positions at the carrousel, both in operation, accept the four labelling stations without tools, so cold-glue and self-adhesive labelling run on the same carrousel; height adjustment of the top part and each station is motorised with container type preselection. Technical data - Manufacturer: Krones - Model: Ergomodul - Year of manufacture: 2020 - Table pitch diameter: 1,200 mm - Rotary plates: 30 - Machine pitch: 125.6 mm - Main drive: controlled servo motor; Danfoss servo motors, container table - Cold-glue stations (2x): ERGOMATIC-CL, 8-shaft glue pallet carrousel, 8-section gripper cylinder d = 350 mm, unwinding length 40-130 mm, steel glue roller, integrated glue pump, gluing height 5-215 mm, housing stainless steel, AISI 304-similar - Self-adhesive stations (2x): AUTOCOL-TS 120, web speed 120 m/min, supply tolerance +/- 0.5 mm, four-axis stand (application height, container diameter, conicity, sloping position), two-reel holder with automatic splicing and end-of-reel detection, driven carrier-film rewinder, ionisation unit, reels up to 390 mm outer diameter, carrier film up to 150 mm - Container infeed: worm with servo drive; detects damaged and fallen-over containers - Container orientation: prepared for camera orientation at the carrousel (360-degree monitoring, one camera); electrical interface prepared, mechanical adjustment unit not installed - Coding: prepared for a laser coder at the carrousel, with laser guarding, safety switch, clock pulse, oil-free air supply - Conveyors: flat-top chain, 83.8 mm wide, stainless steel (AISI 304-similar); servo-driven infeed, PM-motor discharge, centralised frequency inverter control - Machine guarding: lifting doors at the carrousel (polycarbonate), hinged doors at the front table (tempered safety glass) - Pneumatics: Festo; Bosch-Aventics, Norgren Herion, SMC, Bürkert components - Electrical: 400/230 V, AC 3/N/PE, 50 Hz, 28 A full load, 50 A back-up fuse; UPS 400/230 V, 17 A - Media: 92.4 m³/h oil-free compressed air, 0.009 m³/h process water - Weight: approx. 10,600 kg total (carrousel 3,200 kg, front table 3,000 kg, 1,100 kg per cold-glue station, control cabinet 1,000 kg) Hodpfozzz N Hox Afuju Equipment - 2x ERGOMATIC-CL cold-glue labelling stations, interchangeable - 2x AUTOCOL-TS self-adhesive labelling stations, interchangeable - Stand-alone control cabinet with Krones iPanel operator terminal - Central lubrication (Lincoln progressive distributor with motor pump) - Ecopush rejection module - Handling parts set on trolleys The inspection unit (Checkmat) and the container coding device used with this labeller are not part of this machine. Condition Used, still installed and under power in an operating line; on-site inspection possible before purchase. Availability Available now. The machine is in Belgium and will be dismantled and moved to our location in Germany; dismantling, loading and transport quoted on request.

Condition: used, Year of construction: 2023, Overview This Krones Pressant Universal 1N is a container sweep-off depalletizer that lifts each container layer off the pallet stack and sweeps it onto the discharge table, while a separate handling module removes the layer pads and the empty pallets. The machine is built in Krones enviro design for reduced energy and media consumption. Operation is from a Krones touch terminal with a production dashboard and a separate control page for the pallet conveyor. Technical data - Manufacturer / model: Krones PRESSANT UNIVERSAL 1N - Machine type: container sweep-off depalletizer - Year of manufacture: 2023 - Application: depalletizing of glass bottles, several formats - Container throughput: 14,000 containers/h (machine setting) - Pallet format: flat pallets 1,200 x 1,000 mm - Container conveyor height: 1,300 mm - Sweep-off station: raised design for container heights above 320 mm, SEW servo drive - Discharge table: 90° connection, 3,600 mm table length, 15 steel conveyor chains, servo drive (SEW) - Lifting unit: servo drive (SEW), maintenance unit on the columns - Layer scanning: pneumatic - Layer centring: lateral and centring beam servo-motorised (SEW), pneumatic front flap Hjdpfx Aszzz Naofuju - Stack fixing: lateral, motor-driven; pneumatic transfer plate - Packing material handling: 1 module with pivoted arm, suction gripper for layer pads and complete layers, vacuum ejector, pallet gripper (1 DIN size), motorised gripper frame rotation - Magazines: two magazine and stacking areas, free-standing chute for inverted trays - Central lubrication: Lincoln Quicklub, automatic pump - Pneumatics: Festo, minimum operating air pressure 5 bar, air connection G 1/2" - Power supply: 400 / 230 V, 3 Ph, 50 Hz, 57 A - Overall dimensions: depalletizer approx. 6,000 x 3,500 x H 5,620 mm; complete installation approx. 15,900 x 9,600 x H 5,620 mm - Finish: RAL 5013 cobalt blue columns, RAL 9018 papyrus white and RAL 7037 dusty grey machine parts - CE marked Scope of delivery - Krones PRESSANT UNIVERSAL 1N sweep-off depalletizer - Infeed roller conveyor, stainless steel rollers, roller width 1,350 mm, approx. 1,820 x 1,450 x 1,030 mm - Stainless steel platform with chain conveyor, approx. 5,000 x 2,500 x 1,680 mm - Krones PALCO pallet conveyor and Krones SYNCO container transport - Outfeed conveyors, stainless steel belts, belt widths 1,280 mm and 250 mm, approx. 5,200 x 1,700 x 1,420 mm and 5,700 x 500 x 1,420 mm - Krones operator terminal with production dashboard - Control cabinets with SEW servo drives, safety technology and central lubrication - Machine guarding with safety gates and locking pawl on the sweep-off station - OEM machine data sheet and dimension drawing Condition Used, technically complete. The machine is still installed and under power at its production site; the photographs show it in the installed state. Availability Immediately. The machine will be dismantled and relocated to Germany. Viewing by arrangement; dismantling, loading and transport can be quoted on request.

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 13-13, The BLOMAX 4 Blowmoulding machine is of the model 13-13. The machine has no defects and operates in excellent condition with full functionality. Power : 400V/150A/60000W Year of construction : 2000 Hedpfx Afot Akgwjuju

Condition: used, Year of construction: 2018, Overview This Krones Linatronic M is an empty bottle inspector for glass bottles, built in 2018. It inspects every empty container before filling and rejects any container that fails one of the inspection stages. The machine combines camera-based base, sealing surface, screw thread and sidewall inspection with high-frequency and infrared residual liquid and caustic detection. Two sidewall modules with four mirror assemblies and four cameras provide a compact full-front view of the container, and the DualFlash neck finish lighting inspects the outer and inner sealing surface separately using two minimally offset lighting angles. Foreign containers are identified at the machine infeed by height, contour and colour detection. Three Ecopush rejection points separate foreign, dirty and damaged containers. The machine is operated from a Krones iPanel CD terminal. Technical data - Manufacturer: Krones - Model: Linatronic M - Machine type: empty bottle inspector - Year of manufacture: 2018 - Application: inspection of empty bottles prior to filling; neck ring detection for returnable PET containers included - Inspection modules: base inspection, sealing surface inspection, screw thread inspection (cone optics), sidewall inspection - Sidewall inspection: 2 modules with 4 mirror assemblies and 4 cameras, two views per camera at 45° - Residual liquid and caustic detection: high frequency and infrared - Additional detection: polarising transparent films at container base and sidewall, glass fragments at the container base, scuffing via sidewall camera - Foreign bottle detection at the infeed: container height, contour and colour via camera - Rejection: 3 x Ecopush - foreign containers at the infeed, dirty containers and damaged containers at the discharge - Control: Krones iPanel CD operator terminal, prepared for data connection to a single-station PC (Datalyser) - Test bottle programme with 2D code - Conveyor height: 1,200 mm, adjustment range 1,155 - 1,315 mm - Minimum required room height: 2,810 mm - Overall dimensions: approx. 6,700 x 1,300 x H 2,800 mm - Direction of operation: right-left machine - Power supply: 400 / 230 V, 3/N/PE, 50 Hz, 6 A full load current, 20 A pre-fuse; auxiliary supply 230 V, 1/N/PE, 5 A Hsdpfxjzy Ud Ie Afusu - Standards: IEC 61439-1 / IEC 60204-1, CE marked - Machine base and housing: stainless steel (AISI 304 equivalent), clean design Equipment - DualFlash neck finish lighting, separate inspection of outer and inner sealing surface - Combined thread inspection via the sidewall mirror assembly - Fallen container detection in front of the machine (photoelectric sensors with infeed pusher) - Base blow-off unit with clocked air nozzle for foam and lubricant residues - Container blower at the infeed, conveyor dead plate (3-fold) - Servo-driven collection module for rejected containers at the discharge - Festo pneumatic system with maintenance unit, food-grade lubricants - Emergency mode: passage operation without inspection - OEM machine data sheet and dimension drawing Condition Used, technically complete. The machine is still installed and under power at its production site; the photographs show it in the installed state. Availability Immediately. The machine will be dismantled and relocated to Germany. Viewing by arrangement; dismantling, loading and transport can be quoted on request.

Condition: excellent (used), Year of construction: 2010, 200hl Steinecker Krones Brewhouse. Capable of 6 brews per day. Location: UK Available Immediately Including: • Steinecker Mill • Steinecker Cereal Cooker • Steinecker Mash Vessel • Steinecker Lauter Tun • Steinecker Holding Vessel Hodpsxb Uz Asfx Afueu • Steinecker Lauter Worth Heater • Steinecker Copper • Steinecker Whirlpool • Steinecker Wort Cooler • HLT & CLT • Hop Pellets Station • Vapour Condenser • Condensate Cooler • Spent Grain System Contact Indassol UK for Pricing and more details. We are at Drinktec - Please reply to set up a meeting to discuss further.

Condition: new, Year of construction: 2026, functionality: fully functional, input voltage: 220 V, warranty duration: 12 months, total height: 730 mm, total length: 1,115 mm, total width: 490 mm, overall weight: 50 kg, Machine for mini donuts, made of stainless steel materials according to AISI 304, according to the regulatory documents for the food industry. Hjdpfx Aswp Il Hofusu Automatic dosing, turning and removal of the donuts from the fryer. Electronic counter Easy to service.

Condition: used, Year of construction: 2000, machine/vehicle number: 690-264, Machine: KRONES KGW-65-S-E Crate washer Hodpfxjz Ablwe Afuju