Used Horizontal Baling Press for sale (4,176)

Condition: used, HORIZONTAL PRESS PRESSURE 80t Dsdpoihvnmsfx Ackjch

Condition: reconditioned (used), Year of construction: 2007, operating hours: 13,209 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,050 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 700 mm, bale weight: 500 kg, oil tank capacity: 400 l, power: 15 kW (20.39 HP), year of last overhaul: 2025, volume flow: 108 m³/h, Technical data baler: Manufacturer according to type plate BRAMIDAN (original manufacturer Presto GmbH & Co. KG) Type HC 50 (corresponds to the Presto HPK 50) Year of manufacture 2007 Operating hours 13,209 hours, as of March 2026 Number of bales pressed: 23,379 bales Pressing force 50 tonnes Specific pressing force 650 kN/m² Feed chute dimensions 1250 x 1050 mm (L x W) Filling volume 0.96 cm³ Theoretical cycle time 32 seconds Theoretical throughput capacity 108 m³/hour Bale dimensions 1100 x 700 mm (w x h) length variable Drive power 15 kW Power consumption, total in 50 A Tying 4-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm approx. 3.1 t/hour Bulk weight of 60 kg/cbm approx. 4.5 tonnes/hour Bulk weight of 100 kg/cbm approx. 7.2 tonnes/hour Bale weights with a bale length of approx. 1.2 m up to 500 kg, depending on material Hydraulic oil tank capacity 400 litres PLC control Siemens S7-200 Effective transport dimensions excluding baler 6850 x 1950 x 2650 mm (l x w x h) Transport weight of press 8.5 tonnes Condition of the baler: The press was used in a production facility exclusively for pressing cardboard and was regularly serviced. With only 13,209 operating hours, the machine has seen little use. The press was partially overhauled in our workshop and then tested. The following overhaul work was carried out: Machine cleaned Bale retainer made operational and lubricated Light barrier replaced Twisting unit completely dismantled, broken down into individual parts, all bearings replaced, all plastic glides replaced, lubricated, chain tension adjusted Knife and counter knife dismantled, sharpened, reassembled Knife gap readjusted General maintenance work carried out and lubricated Scope of delivery: 1 baler with wire coil boxes, without wire (6850 x 1950 x 2650 mm) 1 bale chute (5100 x 1150 x 450 mm) Dcjdpfjzbxyqex Ackoh 1 floor-mounted wire coil box (1450 x 380 x 360 mm) To transport the baler, you will need a tautliner with an effective internal height of 2700 mm. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, oil tank capacity: 600 l, power: 22 kW (29.91 HP), year of last overhaul: 2025, volume flow: 530 m³/h, For sale is a partially refurbished Presona baling press, with 50 t pressing force, 22 kW drive power, built in 2005 Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Dcjdpfx Ajzbxxaeckeh Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the whirling unit replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, For sale is a complete Bollegraaf baling system consisting of conveyor technology, baling press and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical Throughput rate at a bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Djdpfx Acszbxw Aokech Comments: The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Dcsdpfx Ajy S Rqwockeh Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: ready for operation (used), Year of construction: 2008, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Dsdpfx Aezaqymsckjch Pressing force: 532 kN Voltage: 400 Max. bale weight: up to 550 kg (depending on the material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Feed opening dimensions: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request. Transportation is also possible.

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced Dedpfxovq Rtkj Ackoch - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Dcodpfx Aey R Nnfjckjh Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: ready for operation (used), Year of construction: 1994, Brand: HSM Model: 155 VL Year of construction: 1994 Pressing force: 157 kN Voltage: 400 Max. bale weight: 250 kg Bale dimensions: 110 x 70 x 95 cm Machine weight: 950 kg Machine dimensions: 144 x 100 x 234 cm Dodsy Uwnnepfx Ackech Feed opening dimensions: 110 x 59 cm

Condition: ready for operation (used), Year of construction: 2012, pressing force: 40 t, Manufacturer: HSM Dcodpfox D U N Sjx Ackoh Model: HL 4010 Year of manufacture: 2012

Condition: good (used), Manufacturer: Comp Tip: SB5 Dsdpfoh Eic Ajx Ackjch Engine: 2,2 KW Cylinder stroke length: 500 mm Chamber size: 500 x 350 x 400 mm

Condition: used, Year of construction: 2012, pressing force: 4 t, HSM V-Press 504 waste paper baler - used The HSM V-Press 504 vertical baler is a compact yet extremely efficient device designed for pressing cardboard and plastic waste. Thanks to its robust construction, simple operation, and modern control system, this model is the ideal solution for manufacturing companies, warehouses, stores, and logistics centers where significant amounts of packaging waste are generated every day. The baler, manufactured by the German brand HSM, ensures reliable operation and a long service life. Key advantages of the waste paper baler: 40 kN crushing force – effective waste compression, reducing volume by up to 95%. Dodpfxeyim Ayj Ackjch Efficiency and ergonomics – the crushing process starts automatically when the door is closed, and the piston returns to its starting position automatically. Modern control system – a microprocessor with a membrane keyboard and graphic text display ensures easy monitoring of the work process. Double door with lever – safe and convenient operation even with intensive use. Compact bales up to 60 kg – facilitate transport and storage of processed waste. Integrated bale ejector – increases operator safety and comfort. Energy-efficient operation – 1.1 kW motor allows for full functionality with low energy consumption. Stable, durable construction – guarantees reliability over a long service life. The offer applies to the HSM V-Press 504 waste paper baler: • Product code: MTP006524 • Product condition: used • Year of manufacture: 2012 • Model: V-Press 504 • Width: 102 cm • Depth: 81.5 cm • Height: 193 cm • Weight: 290 kg • Power: 1100 W • Voltage: 230 V Net price: €2,859.00 per unit * I have large quantities available, with the possibility of negotiating the price for larger orders. * Transport possible throughout Europe. * The above offer does not include transport costs. * Location: Chmielów/Tarnobrzeg, Poland.

Condition: used, Year of construction: 1988, operating hours: 1 h, machine/vehicle number: V 516, total width: 2,000 mm, total length: 7,000 mm, total height: 1,800 mm, operating pressure: 300 bar, pressing force: 90 t, sheet thickness aluminum (max.): 5 mm, power: 11 kW (14.96 HP), empty load weight: 16,000 kg, cutting force: 90 t, year of last overhaul: 2025, Bale size 400x400 mm Dodpjlhqd Refx Acksch Force 1 Step 900 KN Force 2 Step 900 KN Steel max. 2500-3500 Kg/Std. Aluminium max. 2000 - 3000 Kg/Std. Driving Power 11 KW Arrangement Surface 7x2x2,5 m x m Machine weight 16 to Place: Austria Aviable: 30.01.2025

Condition: ready for operation (used), Year of construction: 2002, Extruders and oil screw presses for soybean processing, obtaining oil and soybean cake. There are two extruders and two presses. One extruder and one press work in tandem and form a pressing line. The motor power of the press is 22 kW and the power of the extruder is 55 kW. the capacity of one line is 500-800kg/h Dsdpfx Ajtxinaockoch The price refers to one line (exstruder+press)

Condition: used, Year of construction: 1988, pressure 400 t distance between columns 1100 mm stroke 250 mm no. of strokes 25 - 75 /min distance table/ram, max. stroke up, adjustment up 900 mm table surface area 1100 x 965 mm Djdpfxovuukno Ackjch capacity of ejector in table 30 t ejector stroke of ejector in table 80 mm capacity of ejector in ram 3 t stroke of ejector in ram 60 / 70 mm ram surface 980 x 800 mm column travel -side 800 mm ram adjustment 20 mm power capacity 80,0 + 5,5 kW weight 47,0 t Dimensions (WxDxH) 3,5 x 3,3 x 6,0 m weight of switch cabinet 1,4 t dimensions of electrical cabinet (WxDxH) 4,9 x 0,5 x 2,6 m Multi-station cold extrusion press with link drive with infinitely variable drive, hydraulic clutch-brake combination (Ortlinghaus), hydraulic overload protection in the slide, motorised slide adjustment, pneumatic counterbalance cylinder in press frame, cam-controlled ejector in table (30 t / 80 mm), pneumatic ejector in slide (3 t, 60 mm), motorised central lubrication

Condition: new, Year of construction: 2025, functionality: fully functional, input voltage: 380 V, input frequency: 50 Hz, stroke length: 200 mm, operating speed: 50 mm/s, reverse speed: 180 mm/s, table length: 3,200 mm, total length: 3,915 mm, total width: 1,605 mm, total height: 2,655 mm, overall weight: 8,000 kg, bending force (max.): 1,000 t, bending angle (max.): 90 °, warranty duration: 24 months, working height: 450 mm, All-Electric Servo Bending Machine Nominal force(KN): 1000 Slider stroke(mm): 200 Throat depth (mm): 360 X-axistravel(mm): 600 R-axistravel(mm): 200 Z-axistravel(mm): 2500 🔹 Smart CNC System – SL100-P with high-end algorithms and 12-inch touchscreen for intuitive operation. 🔹 High-Precision Structure – Finite element analysis (FEA), annealed, and one-time machining for long-term stability and accuracy. 🔹 4-Axis Intelligent Backgauge – AC servo-driven, high-speed positioning with automatic collision avoidance. 🔹 Precision Compensation System – Adjustable convex strips & fine-tuning mechanism for optimal bending accuracy. 🔹 Powerful & Durable Drive – High-torque servo motor, heavy-duty ball screws & sealed protection for longevity. 🔹 Fully Closed-Loop Control – Y1/Y2 magnetic scale feedback, positioning accuracy ±5μm. 🔹 Optimized Electrical System – Closed electrical box, heat dissipation, & neat wiring for reliability and easy maintenance. 🔹 Imported Precision Components – Ball screws & linear guides ensure accuracy without stroke compensation. Dcjdpfxov Hchlj Ackeh 🔹 High precision, stability, and smart automation – designed for professional sheet metal bending!

Condition: used, Year of construction: 2025, total length: 1,450 mm, total width: 800 mm, total height: 2,200 mm, Empty weight: 970 kg Price: On request Movable Press-Cylinder - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Operating hours: 0 - Drive system: Conventional - Press model: C-Frame press - Press force [ton]: 100 - Max. stroke [mm]: 380 - Table length [mm]: 1500 - Table width [mm]: 300 - Ram length [mm]: 100 - Throat depth [mm]: 1100 Dsdsw N Su Depfx Acksch - Height adjustment [mm]: 750 - Motor power: 3.0kW - Transport dimensions: 1450mm x 800mm x 2200mm (l x w x h) - Transport weight [kg]: 970kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2025, total length: 1,100 mm, total width: 800 mm, total height: 2,200 mm, Empty weight: 540 kg Price: On request Movable pressing-cylinder - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Operating hours: 0 - Drive system: Conventional - Press model: C-Frame press - Press force [ton]: 60 - Max. stroke [mm]: 380 - Table length [mm]: 1000 - Table width [mm]: 260 - Ram length [mm]: 100 - Throat depth [mm]: 750 - Height adjustment [mm]: 750 - Motor power: 2.2kW - Transport dimensions: 1100mm x 800mm x 2200mm (l x w x h) - Transport weight [kg]: 540kg - Transport packages [pcs.]: 1 Dedpfxow N St He Ackech Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2025, total length: 1,300 mm, total height: 1,400 mm, total width: 800 mm, Empty weight: 800 kg Price: On request - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Serial number: HB10011N2025006 Dcedpfexixruox Ackeh - Operating hours: 0 - Control: Teach-in - Motor power: 4.0kW - Transport dimensions: 1300mm x 800mm x 1400mm (l x w x h) - Transport weight [kg]: 800kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2025, total length: 1,200 mm, total width: 800 mm, total height: 1,800 mm, Empty weight: 450 kg Price: On request - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Serial number: PB12093N2025005 - Operating hours: 0 - Drive system: Conventional Dsdpfx Acsxixrhjkjch - Number of rolls [pcs.]: 3 - Power [kW]: 1.5 - Shaft diameter [mm]: 155 - Capacity diameter round [mm]: 50 - Transport dimensions: 1200mm x 800mm x 1800mm (l x w x h) - Transport weight [kg]: 450kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2003, pressure 400 t distance between columns 1060 mm stroke 450 mm no. of strokes 15 - 30 /min distance table/ram, max. stroke up, adjustment up 1160 mm table surface area 1000 x 700 mm capacity of ejector in table 2 x 16 t ejector stroke of ejector in table 125 mm Die cushion pressure in table 120 t Die cushion stroke in table 2 mm capacity of ejector in ram 2 x 4 t stroke of ejector in ram 100 mm ram surface 1000 x 700 mm column travel -side 630 mm power capacity 55,0 kW weight 50,0 t year of manufacture 1986 - overhaul 2003 multi-station press with automatic parts feed, Transfer, drawing cushion in table (2. stage) as is where is, WITHOUT putting into operation, stored in dismantled condition Dcjdpfx Acjvzxpuokeh

Condition: used, With this offer, you are purchasing a used manual transfer press ‘Lotus LTS 150 B from 2023’. Dsdpfsx Eg Upsx Acksch Item for sale: 1 x Lotus LTS 150 B with the following equipment: Includes DTF gel oven Year of manufacture: 2023 Condition: This offer is for a used device, which may show signs of wear (minor scratches or yellowing). The device has been tested for functionality. Packaging and shipping: You are welcome to view the device during our business hours. Please make an appointment! Seaworthy packaging and worldwide shipping available on request! For more information, please feel free to contact us personally.

Year of construction: 2015, condition: new, Press the door lignum-EVERT JOHANSON TPBH 2300X1300 Press bonding framework of internal and external doors " Companies Lignum-Evert Johanson --- pneumatic-hydraulic press bonding size maximum dimensions: Length 2330 mm Width 1330 mm adjustable working pressure and the size of the door bonded Dodocczuqepfx Ackoch hardware give one year warranty

Condition: new, Year of construction: 2024, functionality: fully functional, operating hours: 1 h, type of input current: three-phase, table width: 1,000 mm, table length: 2,600 mm, total length: 2,000 mm, total width: 3,090 mm, total height: 3,600 mm, overall weight: 3,800 kg, workpiece height (max.): 60 mm, Wood gluing press 12 working fields main cylinders 12 x 3 =36 pieces ,cylinders 63 x 60 and 4 pressure side levelling 50 x 50 pieces 12 x 4 =48 pieces .Machine new invoice .Warranty one year .Press rotates with inverter controlled transmission .Press stop is on induction sensor .Or rotates smoothly .Actuation of cylinders with lever switches press field is one meter width 2,6 length 60 mm thickness . Djdpstx T Tyofx Ackech

Year of construction: 2003, condition: used, frame hydraulic press WEGOMA Workspace: width 3600 mm height 2500 mm the amount of lateral hydraulic cylinders 3 pieces top two pieces beam mechanically Move Mechanical compression setting Dcodpfx Acecmat Ujkeh more photos an questions