Used Sheet Rolling Machine for sale (69,155)

Condition: new, Year of construction: 2023, functionality: fully functional, working width: 1,500 mm, feed rate X-axis: 4 m/min, type of input current: three-phase, sheet thickness (max.): 102 mm, total length: 2,300 mm, total width: 2,600 mm, total height: 2,500 mm, overall weight: 4,000 kg, working height: 950 mm, workpiece length (max.): 102 mm, Deburring on both sides in just one pass - of course with 100% reproducible results and precise processing of the inside and outside edges - only the EdgeRacer 1500 D offers you this. The double-sided deburring EdgeRacer 1500 D is the right choice for precise double-sided deburring and edge rounding. In addition to flat sheets, it can also process sheets with beads, notches, thread pull-throughs and the like. The maximum component height is 102 mm. The infeed of the brushes working from above and below can be set independently of each other. Thanks to the roller conveyor, the infeed can also be below or above roller table level. Gjdpfx Aajucw Rbj Ajbk

Condition: used, CNC press brake FASTI type 904-125/30 serial no. 95-904-5775 year of construction 1995 Pressure capacity 125 ton. Working length 3050 mm Stroke approx. 335 mm Stand projection 300 mm Clearance between the side uprights 2550 mm Tool installation height max. 465 mm (opening width between the tool holders) Table width 90 mm (the clamping system is mounted on the table) Table height above floor 875 mm (910 mm with clamping system) Backgauge X-axis 500 mm Backgauge R-axis 115 mm Backgauge Z-axis approx. 1950 mm Lowering speed Y rapid traverse 90 mm/s Lowering speed Y-operation 8.9 mm/s Return stroke speed Y-retraction 75 mm/s Oil filling approx. 160 liters Motor power 18.5 kW Mains connection 400 Volt, 50 Hz, 20 Amp. - 7-axis CNC control DELEM type DA 58 with LCD screen - 1 axis for back gauge - stop depth (X-axis) - 2 axes for back gauge - fence height (finger R1 + finger R2) - 2 axes for back gauge - stop finger, laterally movable (finger Z1 + finger Z2) - 2 axes for press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and 2-hand control panel or 2-hand control panel only - Hydraulic tool clamping for the TRUMPF upper tool system, with 20 mm clamping groove - Hydraulic tool clamping for the lower tool with 13 mm table groove, depth 21 mm (tool pin 13 x 20 mm) - FIESSLER safety light barrier, type AKAS - 2 material support arms at the front, manually movable to the side and height-adjustable Gedpfx Ajhmmfkja Asbk - Electrical diagram, hydraulic diagram, user manual for control available - Control cabinet on the machine - without tools Space requirement L x W x H 5000 x 2500 x 3050 mm Transport dimensions L x W x H 5200 x 1900 x 2950 mm Weight 8.5 tons. Good condition

Year of construction: 2001, condition: used, Erichsen Universal Sheet and Strip Testing Machine Model 145-60 Condition: Used Year of manufacture: 2001 Technical Specifications Hydraulic drive Motor power max.: 11.5 kW / 1500 rpm Pump output (small pump circuit): 12.3 dm³/min Pump output (large pump circuit): 31 dm³/min Gedoyr R Uhepfx Aa Aobk Test cylinder Punching force: 665 kN / 160 bar Hydraulic test head opening Max. operating pressure: 95 bar Holding pressure: 50 bar Drawing force ranges, switchable Small drawing force range: 37 kN / 10 bar Medium drawing force range: 225 kN / 60 bar Large drawing force range: 600 kN / 160 bar Max. drawing stroke: 150 mm Max. drawing speed: 750 mm/min Drawing ram stroke display: Resolution 0.1 mm Electrical connection values Power supply: 400 V three-phase, 50 Hz Fuses: 25 AT and 35 AT Ambient operating temperature: between +5° and +50° C Dimensions, weight Dimensions (L/W/H): 1800 mm / 1320 mm / 1400 mm Net weight: approx. 2400 kg

Condition: used, 3-roll plate bending machine Manufacturer: Luna Model: 8266 20/25 Machine No.: 2202 Gedpoyw S N Ssfx Aa Asbk Working range: 2000 x 2.5 mm sheet thickness Swing-out top roll Power supply: 3-phase, 16 amps

Condition: ready for operation (used), functionality: fully functional, control type: PLC-controlled, 3-roll plate bending machine Manufacturer: FERRO S.R.L. Model: CIT - 1 with 3-axis digital readout Working range: 2000 x 6 mm Hydraulic swing-arm bearing for workpiece change Control panel Gjdsyw S E Hepfx Aa Aobk Emergency stop via cable pull Condition: good / immediately ready for operation

Condition: good (used), functionality: fully functional, type of input current: AC, Pee-Wee Model P24US Hydraulic Thread Rolling Machine for in-feed or thru-feed rolling with helical thru-feed dies Gjdpfxexl Ebhj Aa Aebk Max. rolling pressure: 24 tons Max rolling diameter: 75mm Min rolling diameter: 5mm Max rolling width: 200mm Diameter of rolling spindles: 69.85mm Max thread die diameter:210mm Variable spindle speeds: 20 -90 rpm

Condition: excellent (used), Used Gecam - Euro Fintec 128 steel tube linisher / sander / polishing machine for sale Fintec 128 Tube finishing machine for sale Gbsdpewbh Dyefx Aa Aek Can be viewed under power with your steel tubes

Condition: new, Year of construction: 2025, -TFON Lite SURFACER® Series. The TFON Lite SURFACER® Series enables simultaneous processing of multiple parts, offering unmatched versatility through a range of consumable options and an efficient vacuum table system. Designed for ease of use, it features quick brush changes and the capability to mount two different brushes tailored to your specific applications. -With brushes mounted parallel to the table, the system guarantees flawless grinding performance with every use. Ergonomically engineered, the motor weight is supported by the machine frame itself, significantly reducing operator fatigue and improving workplace safety. -Backed by TFON’s trusted guarantee, the SURFACER® Series strikes the perfect balance between minimizing operational costs and maximizing finish quality. Key Specifications: -Minimum Material Size: 80 × 80 mm. Material Thickness: 3 – 200 mm. Maximum Material Width: 800 mm. Maximum Material Length: 500 mm. Gbedpoqzxhyofx Aa Ajk

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, machine/vehicle number: 630056, overall weight: 5,200 kg, input current: 95 A, ERNST Neptun EBB 1500 is a deburring machine designed for sheet metal processing, used for cleaning and rounding the edges of parts cut by laser, punching, or flame cutting. This machine enables alternating processing of various materials such as steel sheets, aluminum, galvanized steel, or materials with protective film, thanks to its flexible deburring roller and brush set. Key features of the ERNST Neptun EBB 1500: • Versatility: Processes parts made from different materials without the need for constant abrasive changes. • Functionality: Uses a flexible deburring roller and a set of brushes (steel or flap brushes) for deburring or edge rounding. • Precision: Allows for the achievement of an identical and uniform radius on all edges. • Ideal solution for: Companies working with diverse materials where edge processing after cutting is required. Gedpjxmhxxofx Aa Aobk

Condition: used, Year of construction: 1953, working width: 2,040 mm, sheet thickness (max.): 1 mm, sheet thickness steel (max.): 1 mm, We offer this used plate rolling machine C.A. Fastenrath 1906/8, year of manufacture 1953. Year of manufacture: 1953 Gsdsyxy Thspfx Aa Asbk Serial number: A533 Type: 1906/8 Maximum working width: 2040 mm Maximum material thickness: 1.5 mm For any questions or further information, please send us a message or contact us by phone.

Condition: used, Year of construction: 1979, Roundo plate/pipe roller. In recent years, it has primarily been used for rolling smoke pipes with a diameter of 150–160 mm. Four pallets with rollers are included; they are used to determine the pipe diameter. Using a pneumatic cylinder, the end is opened to remove the rolled pipe. I have tested the machine, but the rollers do not run. There is probably a simple solution for this. Machine and rollers weigh approximately 3–4 tons. Godpfxsyvqc Us Aa Ajbk

Condition: new, Year of construction: 2026, number of rollers: 3, roller (bottom) diameter: 110 mm, roller (top) diameter: 110 mm, side roll diameter: 110 mm, roller length: 1,070 mm, sheet thickness steel (max.): 4 mm, Equipment: cone bending device, documentation/manual, emergency stop, foot remote control, hardened rollers, swiveling upper roller, – Capacity 1070 x 4 mm – Electrically adjustable rear roll – Digital display for rear roll movement – Hardened rolls – Conical rolling – Swing-out upper roll – Brake motor – Emergency stop – Documentation – 400V Gbsdpfxoyv R T To Aa Aek

Condition: new, Year of construction: 2026, number of rollers: 3, roller (bottom) diameter: 110 mm, roller (top) diameter: 110 mm, side roll diameter: 110 mm, roller diameter: 110 mm, roller length: 1,270 mm, sheet thickness steel (max.): 4 mm, Equipment: cone bending device, documentation/manual, emergency stop, foot remote control, hardened rollers, swiveling upper roller, – Capacity 1270 x 4 mm Gjdoyv R Tajpfx Aa Aebk – Electrically adjustable rear roll – Digital display for rear roll movement – Hardened rolls – Conical rolling – Swing-out upper roll – Brake motor – Emergency stop – Documentation – 400V

Year of construction: 1987, condition: good (used), Reform SPW 30 CNC high performance grinding machine (roll grinding machine) Machine number: 3728-87 Gsdebq A Huspfx Aa Asbk Year of manufacture: 1987 grinding length 2.000 mm

Condition: excellent (used), Beading machine / edge forming machine from the renowned German manufacturer Weberwerke Siegen. The machine is designed for beading, edging, and forming beads (sickening) on the edges of sheet metal panels. Its solid, heavy cast iron construction ensures stable and precise operation. The open "C"-frame allows for the processing of large sheets and long components. The electric drive with a large flywheel guarantees smooth operation and sufficient torque for sheet metal forming. Pressure and roller guidance are mechanically adjustable. Specification from the nameplate: • Type: BM 4 • Year of manufacture: 1952 • Working width: up to 1250 mm • Sheet thickness: up to approx. 4–5 mm (depending on material) • Material strength: Gb = 45 kg/mm² The machine is not a shear – it does not cut sheet metal, it is solely intended for forming operations. Used condition, complete, visible signs of use consistent with age. Gbedpfx Aaeyga T No Ajk Ideal for metal workshops, tool rooms, maintenance departments, as well as restoration tasks and small batch or bespoke production.

Condition: new, Year of construction: 2024, functionality: fully functional, total length: 3,100 mm, total width: 1,400 mm, total height: 1,800 mm, overall weight: 2,300 kg, nominal power: 23.5 kW (31.95 HP), 12 months warranty, 1800 operating hours Gedpfeyw Hhvjx Aa Aebk

Condition: used, Year of construction: 2022, machine/vehicle number: SN048183, total length: 2,170 mm, total width: 3,300 mm, total height: 2,260 mm, overall weight: 5,000 kg, nominal power: 26.9 kW (36.57 HP), pass-through width: 1,350 mm, Equipment: conveyor belt cleaning brush, magnetic track 400 mm Gbedpfx Aajyw Hg Ej Ajk

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, paper width (max.): 1,800 mm, Unwind diameter: 1,000 mm Rewind diameter: 800 mm Max. speed: 400 m/min Friction shafts for 3 and 6 inch Hydraulic lift at the unwind station Splicing table Gedpfeywl D Njx Aa Asbk Web edge control Tidland knife holders, 20 pieces Semi-automatic knife setting system from Tidland Recipe management Laser positioning We will also dismantle and load the machine onto a truck or sea container at our own expense.

Year of construction: 2021, condition: good (used), functionality: fully functional, machine/vehicle number: C28046-0000, Sheet Metal Tab Placement and Bonding Machine Gbodpfx Ajyw Ht Eoa Ajk In the sheet metal tab placement machine, metal tabs are automatically positioned onto the XPS/EPS core (sandwich panels) based on a laying pattern. The metal tabs are fixed in place using adhesive dots and flush-mounted. For functional details, see the product video. Current XPS/EPS panel sizes suitable for metal tab placement: min. 1,500 x 1,500 mm max. 8,000 x 2,500 mm

Year of construction: 1980, condition: good (used), with initial rounding Technische Daten:/ technical details Biegelänge / bending lenght 2000 mm max. Blechstärke / max. sheet thickness 20 mm Anbiegeleistung / initial rounding 15/11 mm Walzendurchmesser Unterwalzen / roll diameter below rolls 280 mm Oberwalzendurchmesser / diameter of the upper roll 300 mm Antriebsleistung Hauptantrieb / drive capacity main drive 16,2 kW Godpfekzg E Asx Aa Aebk Antriebsleistung Anstellantrieb Oberwalze / drive capacity upper roll 4,8 kW Antriebsleistung Anstellsntrien Unterwalze / drive capacity below roll 3,7 kW Gewicht ca. / weight ca. 14200 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: new, sheet width 1000 mm plate thickness 3,0 mm distance between columns 1050 mm diameter of upper rolls 90 mm Gedpfsyv I Izex Aa Aebk total power requirement 1,1 KW weight of the machine ca. 0,47 t dimensions of the machine ca. 1,7 x 0,8 x 1,35 mm Sheet metal bending machine with custom dimensions: - Capacity 1050 x 3.0 mm - Digital display - Hardened rollers - Conical bending - Swiveling top roller - Brake motor - Safety device: Emergency stop cord - Documentation in English - 400V

Condition: used, Technical data paper roll cutting machine. This machine can only be used for small residual rolls up to a maximum diameter of 400 mm in order to automatically unwind these residual rolls and cut the paper into strips so that it can be better pressed into bales. Manufacturer unknown Type unknown Year of manufacture unknown Dimensions feed table for rolls: Width inside of rolls 2.195 mm Height inside of castors 465 mm Godou Tg Spopfx Aa Aobk Transport dimensions Feed table over all: 2,650 x 1,300 x 2,150 mm (W x H x D) Dimensions roller cutter: Width cutting shaft inside 2.250 mm Transport dimensions of the roll slitter over all: 3,050 x 1,550 x 550 mm (W x H x D) Remarks: There are no further data or documents available. A viewing is possible by appointment. We assume no liability for the technical data and possible errors.

Condition: ready for operation (used), functionality: fully functional, 2500 mm roll length diameter approx. 280 mm Godpfjyw Sg Rsx Aa Ajbk

Condition: ready for operation (used), Manual sheel metal bending machine MSW Type MSW-PBR-1270 Manual box and pan brake Operation: manual clamping system (hand operated) Heavy duty welded steel frame Specifications Gbodpfx Aoyy Nxvsa Ask Max bending length 1250-1270 mm Max sheet thickness 1.5 mm (mild steel) 2.0 mm (aluminum/soft materials) Max clamping height, ca. 40-50 mm Bending angle (degrees) 0-155 Bending system: manual folding beam (lever operated) Clamping system: Hand lever activated upper beam Adjustable bending clearance for different sheet thicknesses Weight, ca. 300 kg

Year of construction: 1991, condition: ready for operation (used), A Krollmann pointing and rolling machine for pointing wire, round, and bar material in preparation for drawing processes is available. Machine body swivel: 90°, shear: available. Wire diameter range: 0.5mm-8mm. An on-site inspection is possible. Gsdpfxjyvuu Us Aa Ajbk