Storage tank

Wedholms T50

Condition: reconditioned (used), Year of construction: 2002, Multicomponent Arburg IMM (Horizontal & Vertical) Clamping force 100 tons. Year 2002. Machine will be delivered RE-Conditioned (full checked tested and operate) Ask us for our service of Start Up with Warranty of working condition. Technical details Hodpfxop Audqj Ai Njfi CLAMPING FORCE 1000 kN SCREW DIAMETER Horizontal bimetalic 25mm SCREW DIAMETER Vertical 18mm INJECTION PRESSURE 2500 BAR INJECTION VOLUMEN horizontal 54gr INJECTION VOLUMEN Vertical 20gr DISTANCE BETWEEN TIE BARS (h x v) 420x420mm MIN. MOULD HIGHT 250mm DAYLIGHT MAX 750mm WORKING HOURS 79.115 YEAR OF BUILDING 2002

Condition: used, Year of construction: 2006, First registration: 11.04.2006 Fendt 307 CI Hfjdoyv S Ulspfx Ai Nei Year of manufacture: 2006 Operating hours: 3,445 Engine: Deutz 4-cylinder turbocharger Displacement: 4,038 cm³ Rated power: 80 HP Max. torque: 423 Nm at 1500 rpm Tank capacity: 108 l Transmission: 40 km/h, 21/21 overdrive, shuttle transmission PTO: Powershiftable 540 / 750 / 1000 Hydraulics: tandem pump 70 l/min at 200 bar Rear lift capacity: 48.9 kN 2 double-acting spool valves, cross control lever Brakes: hydraulic brakes Cabin: air-suspended driver's seat, roof hatch, height and tilt-adjustable steering column, heater (no air conditioning) Front loader with parallel guidance, without third control circuit Sale subject to margin taxation in accordance with § 25a UStG Location: not specified

Condition: as good as new (ex-display), Year of construction: 2011, Used steel storage tank according to EN 12285-1 (with test certificate), double-walled, for underground storage of heating oil and diesel fuel, 1 dome (2 domes also possible as an alternative). Capacity: 100,000 liters Diameter: 2,900 mm Length: approx. 15,750 mm Weight: approx. 18,800 kg In addition, we can equip our tanks with the following accessories: - Leakage monitoring with under- and overpressure leak detectors - Dome shaft with shaft cover in a walkable or drive-over design - Partition walls (as a multi-chamber tank) - Internal coatings (e.g., 2K epoxy resin), partial or full linings - Content and level measuring devices, as well as control and regulation technology - Electric tank heaters - Pumps for heating oil, diesel, biodiesel or gasoline - Fuel dispensers for diesel, biodiesel and gasoline – with complete tank data recording on request - External tank insulation with PU foam Hfsdpfx Aoi Enxdji Nji The tank is cleaned internally, and the external coating has been fully refurbished and tested at 14 kV. Cost-effective delivery with our own truck is possible. Simply let us know the delivery address, and we will provide you with the exact shipping costs immediately. If you require any further information, please call us or send us an email. Trade-in and purchase of tanks/containers is possible; please contact us for details. Delivery time upon agreement! We also have the following sizes of these tanks in stock: - 10,000, 13,000, 16,000, 20,000, 25,000, 30,000, 40,000, 50,000, 60,000, 80,000 liters

Condition: as good as new (ex-display), Year of construction: 2026, SRF Master, illustration on the left 2 m extraction arm Application area Low amounts of smoke/dust Occasional use Benefits Requires little readjustment of the extraction hood More flexible due to the additional hose connection at the rear Features Safe operation thanks to filter monitoring Extraction hood can be rotated and swiveled 360 degrees Sliding handle and cable holder Process: 3-stage Filter type: Disposable filter Filter area: approx. 12 m² Separation rate: > 99% Filter material: Glass fiber fleece Hodpfxodqzbre Ai Nefi Welding fume separation class: W3 Additional filters: Two pre-filters Basic data Extraction capacity: max. 950 m³/h Diameter of extraction arm: Ø 150 mm Length of extraction arm: 2 m Diameter of suction connection: Ø 150 mm Power connection: 230 V / 50 Hz Motor power: 1.1 kW Sound pressure level: 72 dB(A) Dimensions (W x D x H): 705 x 655 x 900 mm Weight: approx. 71 kg

Condition: used, Year of construction: 2010, machine/vehicle number: AT91, Used CIP Tetra Pak year 2010 15T/h The Used CIP Tetra Pak year 2010 15T/h, model Tetra Alcip 1, performs Cleaning in Place (CIP) to automate the cleaning process in bottling and food processing plants. Consequently, this system ensures an effective sanitation cycle without requiring production line disassembly, optimizing downtime and reducing water and detergent consumption. Tetra Pak built the Used CIP Tetra Pak year 2010 15T/h in 2010. Specifically, its 15-ton-per-hour operational capacity makes it suitable for high-productivity plants while ensuring hygiene standards that comply with food and beverage industry regulations. Technical Features of the Used CIP Tetra Pak year 2010 15T/h The Tetra Alcip 1 applies a controlled washing cycle to remove organic and inorganic residues from production circuits. In particular, the system integrates separate tanks for water, alkaline detergent, and acid, and it automatically regulates temperature, chemical concentration, and washing time based on plant requirements. As a result, it enhances the efficiency of cleaning operations. Moreover, the Used CIP Tetra Pak year 2010 15T/h automates the cleaning process, reducing cross-contamination risks and improving production efficiency. Additionally, the system allows operators to configure different washing parameters, which enables adaptation to specific production needs and ensures thorough cleaning of filling lines, pipelines, and heat exchangers. Safety and Process Control The system includes advanced safety features, such as: Sensors that continuously monitor detergent concentration. Temperature and pressure controls throughout the cleaning cycle, ensuring optimal performance. Alarm systems that detect and manage sanitation process anomalies, thereby preventing potential failures. As a result, these features ensure this Used CIP operates reliably, minimizing operational errors and optimizing water and chemical consumption. Furthermore, the system’s automated monitoring enhances safety while reducing maintenance requirements. Operational Advantages Using this Used CIP Tetra Pak  enhances plant productivity in multiple ways. First and foremost, it reduces downtime: the continuous washing system completes fast cleaning cycles without requiring component disassembly. Moreover, it optimizes resource usage: the automatic detergent dosing system prevents chemical waste. Additionally, it ensures regulatory compliance: the system meets high hygiene standards and complies with industry regulations. At the same time, the automated nature of this system helps manufacturers streamline their cleaning procedures. Consequently, businesses benefit from both improved production continuity and reduced operational costs. Likewise, the ability to customize cleaning parameters provides greater control over sanitization processes. Conclusion In summary, this Used CIP Tetra Pak provides an efficient and reliable solution for sanitizing bottling and food production plants. Since its design prioritizes automation, this system minimizes manual intervention while maximizing operational efficiency. Furthermore, its advanced safety features ensure maximum hygiene and productivity in the beverage and liquid food industry. Ultimately, adopting this system allows companies to maintain high sanit... Hfodpfx Aiewga Iuo Nji

Condition: ready for operation (used), Hello, we offer used Erowa Powerchuck with pallets. They have been cleaned and checked by us. Hfsdpfeiq Iy Iox Ai Noi In addition, a functional test was carried out. The chucks have the usual signs of wear, but are technically in good condition. Individual purchase also possible. Wide range of pallets available. Do you have any questions? Then we are at your disposal. Shipping is possible.

Condition: used, Good day, We are offering used clamping devices from Erowa. These are part of the Erowa UPC system and are suitable for die-sinking EDM and milling. The following parts are available: ER-048377 UPC Alignment pallet Erowa T-slot pallet 320x320 Base body made of aluminum, bars hardened and ground. Hfsdpfx Aiotk Hakj Nsi ER-016917 UPC Aluminum pallet 320 x 320 x 40 with clamping bar They have been cleaned and checked by us. A functional test was also carried out. The clamping devices have signs of use and are technically in very good condition. Individual acceptance also possible. Spare parts are available. Do you have any questions? Then please do not hesitate to contact us.

Year of construction: 1983, condition: ready for operation (used), Various mixing and storage silos are available. 1) Stainless steel silo. 2) Stainless steel silo Zeppelin, year of construction: 1983, capacity: 32m³, friction angle range: 25°-45°, overpressure range: 5mbar-45mbar, max operating temperature: 50°C, bulk density: 0.6kg/dm³, silo height: 11250mm, silo diameter: 3000mm. 3) Stainless steel silo. 4) 3x identical HD-PE mixing silos, total height: approx. 10500mm, diameter: 3000mm, volume: approx. 49.5m³, mixing pipes: NW 150, motor power: 15kW. 5) 2x identical storage silos Zeppelin, year of construction: 1980, volume: 127m³, capacity: 119m³, silo diameter: 3500mm, inclination angle: 15°, hopper height: 1680mm, support ring height: 3700mm, total height: 17500mm. Documentation available. An on-site inspection is possible. Individual sale possible. Hfedpfx Aoxxl I Uei Nji

Condition: excellent (used), Year of construction: 2022, IES screw compressed air units supply a continuous, reliable flow of compressed air directly to the point of use without requiring a dedicated room. The ECB – SCB range, made according to high quality standards, uses components by leading companies on the market, ensuring reliability and traceability. 7.5 KW 8 Bar Hjdpoxaxr Nsfx Ai Nofi 1000 lts/min Very low running hours - 1351 run hours Complete with three filter set

Condition: ready for operation (used), Year of construction: 2020, clamping force: 2,200 kN, screw diameter: 70 mm, injection weight: 172 g, This Arburg 570 S 2200-800/290 was manufactured in 2020. It features a hydraulic drive system and the Selogica control system for precise operations. With a clamping force of 2,200 kN and a screw diameter of 40 mm, it is ideal for detailed injection moulding tasks. Consider the opportunity to buy this Arburg 570 S 2200-800/290 hydraulic injection moulding machine. Contact us for more information. Clamping unit • Distance between tie bars: 570 × 570 mm • Opening stroke: 650 mm • Ejector force: 70 kN • Ejector stroke: 200 mmInjection unit • Injection unit size: 290 • Injection pressure: 2,500 bar • Shot volume: 188 cm³Drive & control • Drive system: Hydraulic • Control system: ARBURG Selogica Hfsdpfsx Nkp Iex Ai Nji