Polyp grab

XYZ Machine Tools 3000/MMG

Condition: good (used), Year of construction: 1989, machine/vehicle number: AN-No.: 89.04.019 A, 5 pieces Jakob Müller Frick AG NF 42 in 5x 4/42mm with Müdata, Mütrans, without gate, super clean from Germany 2nd hand NF42 in 4/42mm from 1988-1990 Bedpfxer I Am He Ab Uelf AN. No.: 88.04.017 H ex.Alge, Müdata, 16 stocks very clean 7.000 Euro AN. No.: 88.04.169 D ex.Alge, Müdata, 16 stocks very clean 7.000 Euro No. 213 AN. No.: 89.04.019 B ex.Alge, Müdata, 16 shafts very clean 7.000 Euro No. 223 AN. No.: 89.04.046 B ex.Alge, Müdata, 16 shafts very clean 7.000 Euro AN. No.: 90.00.066 B ex.Alge, Müdata, 16 shafts very clean 7.000 Euro

Condition: excellent (used), Year of construction: 2023, operating hours: 1,500 h, functionality: fully functional, cutting force: 630 t, power: 90 kW (122.37 HP), empty load weight: 36,500 kg, total width: 2,400 mm, total length: 9,500 mm, overall weight: 40,000 kg, cutting length (max.): 1,600 mm, year of last overhaul: 2024, type of input current: three-phase, operating pressure: 220 bar, Scrap shear MS-6300e (scrap shear with electric motor) without operating materials. A 250kW diesel generator can be offered separately. Model: MS-6300e Cutting force: 630t Cutting length: 1600mm Discharge height: 500mm Power: 110 KW Capacity: 12-17 t/h Machine weight: 40 tons (+ diesel generator 4 tons) Hopper size: 3850mm x 2600mm x 1500mm Information: A scrap shear is used for economical scrap cutting: - simple automatic operation - Energy-saving - Cost-saving - No foundation required Function: Bjdpfxouu Upgj Ab Uelf Scrap is fed into the loading area with the aid of an excavator. Due to the horizontal filling area and the scrap's own weight, it falls down into the loading chamber and into the cutting area. The scrap is compacted at the front wall and cut by the horizontally moving tool pick-up side via the blades on the front wall. While the tool carrier carriage moves horizontally, the processed material is pushed out via the blades on the front wall of the container. When returning to the rear position, the loaded scrap moves into the interior of the shears under its own weight. The scrap shears are available in different versions depending on customer requirements and the output size can be selected (for new orders). Inspection and trial operation are possible.

Condition: good (used), Year of construction: 1994, functionality: fully functional, power: 75 kW (101.97 HP), Low-speed rotor with push floor Rotor width 2500 mm Rotor diameter approx. 400 mm Bjdpfxotgqlys Ab Ujlf Motor 75 kw Discharge via conveyor belt with magnetic roller

Year of construction: 1987, condition: used, Kehren rotary table type RS 7C, second-hand manufacturer: Kehren, Honneff Comm.: 4179 year of construction: 1987 Control: Siemens 3G SPS: Siemens S5 grinding motor: BBC QUB 200 rotary table ø: 750 mm Bodpfxohgmwgj Ab Uolf ø grinding head:460 mm Control panel with screen Coolant system Flushing pump Coolant pump Automatic paper belt filter system Control cabinet

Condition: good (used), Year of construction: 2002, Beringer BPx4 ergo Bsdpfotp Hnwox Ab Uslf Useful volume 6cbm tested, serviced, fully functional Can be painted in the desired RAL color. Noes3koku We would be happy to make you an offer including delivery.

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Blodpswp Rqfofx Ab Usf Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: ready for operation (used), functionality: limited functionality, disc diameter: 525 mm, Weight approx. 1,900 kg Dimensions (LxWxH) approx. 1,800x1,500x2,200 mm Working disc diameter 525 mm Largest disc ring width 175 mm Largest workpiece dimension 170 mm Bljdeh Invropfx Ab Uef Speed of the working disc 45/70/90/140 rpm Main drive performance 4.0 kW Connection 400V/50Hz Emergency stop switch Conventional control with control panel Full-fledged lapping machine, conventional control

Condition: used, Magnetic drill, hand drill -Magnetic base: Magnetor type PS 32 L -Drilling machine: AEG type HBE-IV - Recording: MK2 -Max. Drill: Ø 23 mm -Connection: 265V/200Hz Bodjfc R D Aspfx Ab Uslf -Dimensions: 700/300/H670 mm -Weight: 49 kg

Condition: good (used), functionality: fully functional, Conveyor belt length: approx. 28 m Discharge height: approx. 10 m Bsdpfjv Scaxox Ab Uelf Feed hopper capacity: approx. 10 m³ with adjustable dosing conveyor belt 2 transport conveyor belts (one flexible) on a 3-axle chassis Powered by an ENDRESS 45 kVA generator

Condition: good (used), power: 122 kW (165.87 HP), overall weight: 27,000 kg, Year of construction: 2001, operating hours: 21,200 h, For sale is a Sennebogen 825 Year of manufacture: 2001 Bledpfx Abeua At No Usf Operating hours: 21200 Total weight: 27000Kg