3d metal printer

GE Additive Arcam EBM Q20plus

Year of construction: 1998, condition: like new (used), 65 Watt YAG laser Lrsdpfed Dhw Njx Akqok

Condition: good (used), Year of construction: 2000, table width: 1,000 mm, table length: 1,800 mm, ram plate width: 600 mm, total length: 25,000 mm, total width: 27,000 mm, total height: 47,000 mm, overall weight: 43,000 kg, die cushion stroke: 200 mm, Siemens Simatic OP 27 control system Lsdpfxstiwgis Akqerk Light barrier Sick Separate control cabinet Ritta Side passages Ground level installation

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: Lredpfswp Rqfjx Akqek • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: excellent (used), Year of construction: 2016, Inca Onset X2, 3/4 automized Color configuration: 8 channel printer with four colours (CMYK) 1/12th of the new price !!!!! Printhead status allowing to print at maximum speed with outstanding quality, up to 140 beds per hour/700m² per hour, needs replacement of 60 heads (circa 45.000€) The machine is in excellent shape, serviced by manufacturer since day number one. Annual maintenance done in May 2025. Available: January 2026 As the business expands, Onset X2 provides the capacity to extend the range of jobs companies can handle. The addition of a second set of CMYK delivers even higher productivity - up to 707m²/hr* (equivalent to 138 full-bed sheets/hr) - while an optional six channels can be populated with light cyan (Lc), light magenta (Lm), white (W) and orange (O) to add versatility and superb quality. A choice of uni-directional, bi-directional and super high-quality print modes can be selected depending on the specific job requirements. * Based on an approximate 6 second material handling time. Decomissioning, transport, installation, training and warranty are included (in Europe) For further technical details please refer to enclosed data sheet. Ljdpfx Asun Swbokqerk

Condition: new, Year of construction: 2025, Entry-level sheet fiber laser metal cutting machine Lrodpfxshwrgto Akqok Lower laser cutting cost and easy operation The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Laser Power: 1000W, 1500W, 2000W, 3000W Cutting Area: 3000*1524mm Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Cutting Speed: 0-100m/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: used, Year of construction: 2026, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 204065, Used machine CNC cutter/plotter Cutting area in X and Y: 3,500 x 2,100 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials Equipment of the used machine • 1 cutting bridge and 1 multifunctional tool head The machine is sold with one driven circular knife, electric oscillating knife and one Milling Head + exhaust • Multifunctional tool head to hold max. 2 interchangeable tools • powerful vacuum blower for fixing the material Lrsdpfxeif Ek Ro Akqsk • Standard equipped with gray conveyor table (Conveyor). Green-blue exchange conveyor possible (offers high contrast for dark materials) Can be extended with other tools (on request): • EOT electric oscillating blade • POT pneumatic oscillating knife • PRT rotating blade • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) (Product photo as example) The machine is CE certified.

Year of construction: 2026, condition: new, functionality: fully functional, Complete plastics recycling line for films and fibre materials from Taiwan leading Plastics Recycling Machinery manufacturer. GENIUS Machinery Co who have more than 30 years of recycling extruder production and experience. Extruder can be fed without size reduction or shredding.. Materials in baled, loose or reel form can be fed. Line can be supplied complete with Belt conveyor, Cutter compactor, Main extruder, Filtration system, (variety of types to suit requirements), Hot pellet die-face cutting device, Centrifugal pellet dryer, Vibrating screener, Storage silo for pellets. Additional ancillary equipment can be supplied . A two stage " Cascade" version is also available for heavily printed films, or very dirty films requiring double filtration. Alternative sizes from 100 kgs per hr up to 1200 kgs per hr can be offered. Full sales and support and training is available in UK and Europe for these extremely modern and economic machines. Lodpfx Akswg R Rtsqork

Condition: used, Year of construction: 2015, Vertical CNC machining center with 3 controlled axes and exceptional Y-axis machining capacity. It is equipped with a vacuum table clamping system that holds plates and sheets with the help of vacuum. This solution is particularly effective when machining thin parts that are difficult to fix using conventional clamping systems. The machining center is equipped with a set of valves that allow you to turn on or off different table zones, thus concentrating the vacuum in a specific area and optimizing the clamping of small components. Possibility of performing interpolated milling and drilling in composite panels, aluminum, steel or titanium sheets and aluminum profiles. Tekna provides user-friendly software that can be operated by both experienced CNC programmers and less experienced users. The TKE 783 is a machining center with 3 controlled axes for interpolated drilling and milling in composite panels, aluminum, steel or titanium sheets and aluminum profiles. Technical specifications: Model: Tekna TKE783 Year of manufacture: 2015 Power: 29 kW Dimensions of the machining table: 2010 x 6300 mm Weight: 4842 kg Ledpfx Asv D A Imskqsrk Speed: X axis 70 m/min; Y axis 55 m/min; Z axis 30 m/min Software: Windows, Embedded, Teach-in software CAD/CAM 2D NC TOOL Made in: Italy Other: aluminum milling up to 4 mm was worked on. The machine is connected, you can see how it works and test it in Estonia. It will be ready for transportation in April-May. If you have any additional questions, we will be happy to answer them.

Condition: like new (used), Year of construction: 2004, AMADA MODEL HFT 8025 80 tons capacity x 2500 bending length hydraulic downstroking press brake complete with CD 2000 4 AXIS colour graphic cnc control, ERWIN SICK machine mounted electronic guards , side and rear interlocked fencing Model Amada HFT 8025 downstoke CNC Press brake Year 2004 Tonnage 100 KN Type CD 2000 CNC Controlled Axis Y1, Y2, X, R Max. Bend Length 2500 mm Open height 470 mm Lrjdpou A Dgrjfx Akqjk Stroke Length 350 mm Approach Speed 100 mm/sec Bending Speed 1 - 10 mm/sec Return Speed 1-100 mm/sec Oil Capacity Motor Power 7.5kw Weight 6100 kg Bed Length 2500 mm Bed Width 60 mm Open Height 470 mm Throat Depth 420 mm CNC Control Backguage Stoke (X axis) 700 mm/s Max gauge 1000mm R axis 250mm can be demonstrated under power BROCHURE AND FURTHER INFORATION AVAILABLE UPON REQUEST

Condition: as good as new (ex-display), Various designs such as round, hexagonal or square and in smooth smooth version, cross-grooved version or with longitudinal and transverse grooves. Ljdsh Dmamjpfx Akqork A current list of available new and as-new SK32/SK42/SK52/SK65/SK80/SK100 expansion chucks can be found on our homepage. We look forward to your inquiry. STALEX Machine Tools GmbH