Condition: ready for operation (used), Year of construction: 1986, functionality: fully functional, machine/vehicle number: 97862034, installation height: 255 mm, sheet thickness (max.): 5 mm, working width: 180 mm, pressing force: 100 t, stroke length: 50 mm, TECHNICAL DETAILS Pressing force: 100 t Total force: 1,000 kN Ring serration force: 40 - 310 kN Counter-holder force: 10 - 270 kN Maximum material width: 180 mm Maximum material thickness: 5 mm Hodpfsytcd Rex Ab Toni Strokes per minute (min.): 20 rpm Strokes per minute (max.): 80 rpm Stroke: 50 mm Feed unit Maximum strip thickness: 5 mm Maximum strip width: 180 mm Maximum feed length per ram stroke: 999.9 mm Tensile force per feed (starting force): 6 kN Clamping force: max. 19 kN Maximum feed height adjustment: +40 mm Maximum distance between feed rollers: 20 mm Resolution (per rollers): 0.1 mm MACHINE DETAILS Input voltage: 400 V Input frequency: 50 Hz Connected load: 13.5 kW Pump power: 3 kW Motor power: 3 kW Air connection: 6 bar Height adjustment type: hydraulic Dimensions & Weight Dimensions (H x W x D): 2,420 x 2,325 x 1,665 mm Installation height: 255 mm Weight: approx. 6 t Year of last overhaul: 1997 EQUIPMENT Decoiler unit Two tool sets Note: Further technical details on the machine can be found in the attached operating manual.

Condition: used, Year of construction: 1992, pressure 80 t stroke 40 mm no. of strokes 60-300 Hub/min table surface area 730x750 mm weight of the machine ca. 14 t Hsdpfx Abswz Rv Ej Toni

Condition: ready for operation (used), total height: 4,900 mm, total width: 5,900 mm, total length: 8,500 mm, passage width: 3,900 mm, power: 11 kW (14.96 HP), empty load weight: 85,000 kg, load capacity: 400,000 kg, Portaalrichtpers 400 ton Model: GANTRY-400T Voor het gericht van assen, gietstalen producten, gewalste producten, smeedstukken met vrije matrijs, vlak staal maar ook voor het in- en uitpersen van lagers, bussen, krimpringen,... 14 individuele tegendrukcilinders in de tabel - 3 ton dop per cilinder - 100 mm slak per cilinder - Druk 300 kg/cm² - Doorgang tussen de staanders: 3990 mm Werksnelheid – bij max. druk: 2 mm/sec Terugloopsnelheid: 50 mm/sec Sluitsnelheid: 30 mm/sec Max ram adjustment: 1550 mm Drawningspeed: 30 mm/sec Workingspeed: 2 mm/sec Returningspeed: 50 mm/sec Max distance between table - ram: 1550 mm Hedpfsyt S Uxsx Ab Toni Dimensions of the table: 7000 x 3200 mm

Condition: ready for operation (used), total width: 2,600 mm, total length: 3,100 mm, passage width: 1,250 mm, empty load weight: 25,000 kg, Model: HZPUX 150/100-1250/1000 Capacity: 230T Max ram adjustment: 1100 mm Max distance between table - ram: 2250 mm Dimensions of the table: 1000 x 1250 mm dimensions stamp: 1000 x 770 mm Hnjdpjyt S U Ejfx Ab Tji Electric motor (power): 70 CV Courant needed: 380 V Height: 6200 + 1250 mm

Year of construction: 2003, condition: ready for operation (used), overall weight: 16,300 kg, total width: 3,110 mm, total height: 1,855 mm, pressing force: 23 t, product length (max.): 3,735 mm, stroke length: 275 mm, Hydraulic press manufactured in 2003. This Darley EHP-LS 230.31/25 features a press force of 230 tons and a maximum bending length of 3100 mm. It includes a throat depth of 400 mm and a stroke of 275 mm. The machine is equipped with CNC control and independent hydraulic axes for enhanced precision. If you are looking to get high-quality bending capabilities, consider the Darley EHP-LS 230.31/25 hydraulic press we have for sale. Contact us for further details. • Technical specifications • Max hydraulic pressure: 250–300 bar Hedeyuya Sopfx Ab Tsni • Distance between columns: 2550 mm • Throat depth: 400 mm • Table width: 170 mm • Table height: 900 mm • Max opening: 500 mm • Rapid approach speed: 120 / 140 mm/s • Working speed: 10 mm/s • Oil tank capacity: 200 L • Main drive power: 24.5 kW • Max power consumption: approx. 27–32 kW • Noise level: 72–78 dB(A) • Backgauge • X-axis range: 0–800 mm • Z-axis range: 80–2150 mm • R-axis height adjustment: 190 mm • Accuracy: ±0.05 mm (X/Z), 0.1 mm (R) • Positioning speed: • X axis: up to 400 mm/s • Z axis: up to 250 mm/s • R axis: up to 100 mm/s • Number of backgauge fingers: 2 (expandable) • Axes configuration: 6 axes (X1, X2, Z1, Z2, R1, R2) • Equipment / Features • CNC control (commonly Delem DA series) • CNC crowning (table compensation) • Independent Y1/Y2 hydraulic axes • Backgauge with X, R, Z axes • WILA hydraulic upper clamping • Pneumatic lower clamping • Optional front laser safety system Technical Specification Bending Length 3100 mm

Condition: good (used), Year of construction: 2002, overall weight: 5,900 kg, pressing force: 63 t, Model: PREN-63 Year: 2002 Weight: 5900 Kg Nominal force: 63Tn Type: Pneumatic clutch eccentric Normal stop position (PMS): 650mm Closing height (PMI): 350 mm Travel: 10-100 mm Motor: 5,5Kw 380V 50Hz Max. carriage adjustment: 65mm Hnsdpfxsuifr Hj Ab Toi Air pressure: min. 3,5 max. 6 bars Total stopping time: 278ms Safety distance: 445 mm Maximum RPM at flywheel: 600

Condition: used, pressing force: 100 t, input voltage: 380 V, Hydraulic press Brand: Francisco CAMP Force: 100 tons Maximum piston stroke: 150 mm Hodpox Syc Nefx Ab Toni Motor: 2 HP Power: Three-phase 380V Operation by pedal/control panel Table dimensions: 780 x 330 mm Clear press width: 780 mm Clear height from table to piston base: 400 mm

Year of construction: 2020, condition: as good as new (ex-display), Hydraulic press for tests and retouching of dies Brand: MHG Model: ER.2S.DM-300/2100 Serial number: 927 Year: 2020 Required power: 40kw Hydraulic oil: 1000Ltrs. deposit + 200 liters. circuit filling Total number of cycles: 403 (NEW MACHINE, PRACTICALLY UNUSED) Maximum force: 300t Number of cylinders: 3 Hjdpfxjk Sgvye Ab Toni Maximum tooling dimensions: 1400x1400mm Maximum tooling mass: 16,000kg Maximum working table and mobile table opening: 1690mm Minimum opening of work table and mobile table: 960mm Maximum mobile table travel: 730mm Approach speed: 92 mm/s Recoil speed: 93mm/s Stop time: 0.2s Safety distance: 500mm Weight with empty tank: 35.000kg

Condition: good (used), Year of construction: 1991, operating speed: 8 mm/s, column diameter: 200 mm, retraction force: 30 t, reverse speed: 40 mm/s, Brand: LoireSafe Year: 1991 Type: Hydraulic Maximum Force: 15-150Tn Return force: 30Tn Movable platen stroke: 1200mm Table dimensions: 2800x1500mm Moving platen dimensions: 2800x1500mm Table displacement stroke: 1500mm Guided height: 800mm Diameter of columns: 200 mm Hnsdpfxoudv D No Ab Tei Height of the table to the floor: 700 mm Power: 11Kw Approach speed: 50 mm/sec. Working speed: 8 to 2mm/sec. Return speed: 40 mm/sec

Condition: used, pressing force: 150 t, Eccentric Press Brand: ULECIA Serial No.: 1877 Type: Pneumatic Clutch Force: 150 t Strokes per minute: 40 Stroke (Max / Min): 160 / 24 mm Power: 10 HP Hnsdpfjylzcvsx Ab Tsi *The press is delivered as is, without any type of warranty.

Condition: used, Year of construction: 2003, pressing force: 120 t, overall weight: 12,000 kg, Hydraulic Press Brake Brand: Hidrogarne / Ermaksan Model: AP 4100-120 Year: 2003 Power: 11KW Weight: 12,000kg Bending length: 4100mm Force: 120t Approach speed: 80mm/s Hjdjx Tp Auopfx Ab Teni Working speed: 8mm/s Y-axis and X-axis back gauge control with ELGO control system. PROMECAM punch holder. Supplied with: - 4m one-piece die, 90x90mm with several V openings - 4m gooseneck punch, 90mm height, in 835mm sections and some additional smaller pieces - Also comes with sets of straight and 30-degree punches (see pallet photos of punches)

Condition: used, pressing force: 160 t, Eccentric Press Hsdpfxoyl Tuwj Ab Tjni Brand: AITOR Model: ARMM/EF Type: Pneumatic clutch Year: 1992 Force: 160 t Strokes per minute: 50 Stroke (Max / Min): 180 / 5 mm Maximum connecting rod extension: 120 mm Weight: 13,000 kg *The press is delivered as is, without any kind of warranty.

Condition: good (used), Year of construction: 1974, pressing force: 100 t, Model: OB1 Pressing force: 100Tm Torque: 3500kg Plate thickness: 10mm Pusher slider: 5-159mm Distance between table and spindle/pusher: 530mm Max. spindle/pusher travel: 130mm Hnodjudwr Ujpfx Ab Toi Strokes per minute: 53

Condition: good (used), Used hose crimping machine from Finn Power Lillbackan Konepaja Type: P 32 RAE Hnsdpfx Ajytb D Aeb Tsi Including various dies up to 52 mm diameter Capacity up to 78 mm (excluding dies)

Condition: used, Single-column hydraulic press with draw cushion RÖCHER Type REP 100.01 SZ Hydraulic deep-drawing press Machine No. 15.499 Year of manufacture 2003 Pressing force: 100 tons Ram stroke: 500 mm Throat depth: 370 mm Installation height: 600 mm Table surface: 850 x 700 mm with a drop-through hole Ø 150 mm Ram surface: 700 x 600 mm Ram ejector force: 16 tons (160 kN) Ram ejector stroke: 100 mm Ram ejector with internal thread M24 x 1.5 mm Hnsdpfx Absyupulj Toi Draw cushion force: 40 tons (400 kN) Draw cushion stroke: 200 mm Draw cushion area: 530 x 530 mm Pressure holding time: 0 to 90 sec. Table height above floor: 910 mm Hydraulic operating pressure: max. 300 bar Hydraulic tank capacity: 700 liters Approach speed (rapid traverse): approx. 400 mm/sec. Pressing speed up to 23.8 tons (238 kN): 5 to 68 mm/sec. Pressing speed up to 100 tons (1000 kN): 5 to 16 mm/sec. Return speed: 50 to 400 mm/sec. Main pump drive power: 18.5 kW Auxiliary pump drive power: 4 kW Power supply: 400 Volt, 50 Hz (63 Amps) - Operation and programming via PC 670 touch panel, keyboard and mouse - Machine control via SIEMENS S7-300 PLC system - Ram stroke and press force programmable via control system - Draw cushion with drawing and ejector function - Draw cushion force infinitely adjustable - Ram and draw cushion equipped with direct linear measurement system - Draw cushion can be moved in and out under the press area, for punching work using the drop-through hole - Floor-level installation, draw cushion does not penetrate the floor - Pressure and stroke cutoff - Fixed stop with indirect measurement system - Pressure holding time infinitely programmable - Table with holes for the draw cushion ram rods - Ram with ejector - Knock-out damping - Stroke triggering via two-hand operation, foot switch, hand lever and push button on the control panel - LEUZE light barrier as reach-in protection for safety operation - Front mirror columns on the press table can be shifted laterally - Electrical control cabinet mounted on machine frame - Hydraulic oil cooler with fan motor (oil-air cooling) - Manual central lubrication pump - 2x hose connections for tool tempering or cooling at the ram - Piece counter in the control system - 306 read operating hours - Operating manual, hydraulic diagram, and electrical diagram available Space requirements (L x W x H): 3100 x 1800 x 4160 mm Weight: approx. 13 tons Very good condition, as new

Condition: used, Year of construction: 1997, pressure 1000 t distance between columns 1260 mm stroke 315 mm no. of strokes 10, 21 - 42 /min distance table/ram, max. stroke up, adjustment up 1295 mm table surface area 1250 x 800 mm table height over floor 670 mm side window 830 mm capacity of ejector in table 63 t ejector stroke of ejector in table 75 mm capacity of ejector in ram 16 t stroke of ejector in ram 23 mm ram surface 1250 x 800 mm ram adjustment 20 mm feeding length transfer 0 - 250 mm closing travel of each rail programmable 0 - 140 mm Hjdpfevuukuex Ab Tsni no. of strokes of the transfer 42 /min power requirement 135,0 kW weight 120,0 t Dimensions (WxDxH) 5,9 x 4,8 x 7,95 m height above floor 6,95 m height beneath floor 1,0 m with DC drive, pneumatic clutch, motoric ram adjustment, pneumatic counterbalance in ram, mechanical ejector in table (pneumatically controlled), mechanical ejector in ram, ram interlocking, die clamping system in table and ram, motoric oil circular lubrication, grease lubrication control of the press: Siemens S 5 - CNC 2-Achs-Transfer (Fabrikat Dreher, Type STV-D Modell 350/100-SO, Bj. 2008), Steuerung Siemens S 7 - cleaning system (make Beyss, yom. 1989) as is where is, WITHOUT putting into operation, stored in dismantled condition The press was previously installed in a soundproof enclosure, which is not part of the scope of delivery Video at seller's site before dismantling available

Condition: used, Year of construction: 2004, total height: 2,620 mm, total width: 1,450 mm, total length: 2,650 mm, Empty weight: 2.500 kg - Year: 2004 - Documentation available: No - CE marking present: Yes Hnodpfsytghtjx Ab Toi - CE certificate present: No - Serial number: 180253 - Drive system: Conventional - Press model: Workshop press - Press configuration: Single-acting - Press force [ton]: 150 - Max. stroke [mm]: 340 - Table width [mm]: 1570 - Ram length [mm]: 280 - Ram width [mm]: 200 - Height adjustment [mm]: 800 - Pressing speed [mm/s]: 5 - Column spacing width [mm]: 1570 - Transport dimensions: 2650mm x 1450mm x 2625mm (l x w x h) - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, This horizontal bender is being auctioned in our industrial/machinery auction for educational institutions – Making Room for New Equipment! (No VAT statement), online. Hsdpfxoyuvwyj Ab Toni

Year of construction: 2018, condition: ready for operation (used), This MILLUTENSIL MIL 163 was manufactured in 2018. A robust hydraulic press with a table size of 2000 mm by 1200 mm, it can handle a maximum load of 5000 kg and exerts up to 163 tons of pressure. Ideal for applications like mold adjustment, injection molding, and die casting. Control is manual or semi-automatic. Contact us for more information. Application Types Bending Hnedpox D Rlijfx Ab Toi

Condition: used, Year of construction: 2005, Pressure 1000 t distance between columns 4100 mm stroke 1200 mm Distance table/ram, stroke up 2100 mm Table surface area 4000 x 2200 mm pressure of drawing cushion in table 360 t Die cushion stroke in table 300 mm Die cushion area in table 3500 x 1600 mm Die cushion pressure in ram 100 t Die cushion stroke in ram 160 mm Die cushion area in ram 3250 x 1600 mm Ram surface 4000 x 2200 mm Side window 1300 mm Oil volume 8000 l Power capacity 300,0 kW Dimensions (WxDxH) 5,75 x 4,3 x 9,55 m Height above floor 7,7 m year of manufacture 1973 - modernization 2005 with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning stored in dismantled condition Video at seller’s site before dismantling available Hjdpfx Aevuubgob Tsni

Condition: used, Year of construction: 1977, pressure 050 t throat 255 mm stroke 8 - 120 mm no. of strokes 115 /min distance table/ram, max. stroke up, adjustment up 380 mm table surface area 640 x 500 mm hole in the table 250 x 180 mm table height over floor 710 - 930 mm table adjustable 220 mm ram surface 550 x 170 mm ram adjustment 70 mm power requirement 4,0 kW weight 3,1 t dimensions (WxDxH) 1,5 x 1,5 x 2,3 m year of manufacture 1951 - modernized 1977 permitted only for safe tools or fixed screen according to the German Safety Regulations (UVV) Hnodovzxr Aopfx Ab Tsi with motor, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, adjustable table, manual central lubrication, foot operation as is where is, WITHOUT putting into operation Price for commissioning (in given condition) on request

Condition: used, Year of construction: 1988, pressure 70 t distance between columns 750 mm stroke 900 mm Hsdpfx Absvuumpe Toni table surface area 700 x 1000 mm Distance table/ram, stroke up 900 mm table height over floor 680 mm ram surface 700 x 1000 mm side window 600 mm max. tool weight 5,0 t max. capacity of swivelling ram plate 2,0 t Speed down 0 - 50 mm/s Speed up 0 - 48 mm/s Working speed 0 - 8 mm/s oil volume 140 l power capacity 9,5 kW weight 8,0 t Dimensions (WxDxH) 2,2 x 1,2 x 3,7 m with swivelling ram, movable table, ejector in table can be inspected in running condition in our warehouse

Condition: used, Year of construction: 2004, pressure 80 t stroke 16 - 63 mm no. of strokes 100 - 750 /min distance between columns 970 mm dayligth (stroke and adjustment up) 380 mm column travel -side 380 mm Hnsdpjvuua Njfx Ab Toi table surface area 940 x 910 mm hole in the table 770 x 190 mm table height over floor 1180 mm ram surface 940 x 510 mm ram adjustment 76 mm material width 203 mm material thickness - 6,0 mm feed length 0 - 120 mm power requirement 37,0 kW Weight 14,50 t dimensions of the machine ca. 2,7 x 1,7 x 3,6 m permitted for automatic mode according to the CE-Norm with infinitely variable drive, pneumatic clutch/brake combination, semi-automatic stroke adjustment, motoric ram adjustment, fix table, circular oil lubrication mechanical roll feed Bruderer BBV 205/120 with drive via main shaft / pivot shaft of the press consoles Guethle CK A noise enclosure can be offered optionally - price on request

Condition: used, Year of construction: 1998, pressure 160 t stroke 30 - 90 mm no. of strokes 50 - 300 /min distance between columns 1270 mm dayligth (stroke and adjustment up) 590 mm column travel -side 440 mm table surface area 1250 x 900 mm hole in the table 950 x 300 mm Hnjdpfxjvut Uxe Ab Tsi ram surface 1250 x 800 mm ram adjustment 100 mm material width 200 mm material thickness - 6,0 mm feed length 0 - 120 mm power requirement 64,5 kW Weight 21,00 t dimensions of the machine ca. 3,0 x 2,2 x 3,9 mxmxm permitted for automatic mode according to the CE-Norm with infinitely variable drive, hydraulic clutch/brake combination (make Desch), automatic stroke adjustment, motoric ram adjustment, fix table, circular oil lubrication mechanical roll feed Bruderer BBV 205/120 with drive via main shaft / pivot shaft of the press consoles Guethle CK 01/0800

Condition: used, Year of construction: 1980, pressure 250 t distance between columns 2000 mm stroke 600 mm Distance table/ram, stroke up 1000 mm table surface area 1700 x 1300 mm table height over floor 800 mm die cushion pressure in table 100 t die cushion stroke in table 180 mm Die cushion area in table 1650 x 700 mm side window 1000 mm ram surface 1700 x 1400 mm weight 31,1 t dimensions (WxDxH) 3,3 x 1,9 x 4,85 m Height above floor 4,55 m Hsdpfsvut Tnsx Ab Teni permitted for manual loading according to the German Safety Regulations (UVV) with oil-hydraulic drive, hydraulic drawing cushion in table, hydraulic cutting impact No foundation pit necessary can be offered without putting into operation, with putting into operation in given condition or alternatively with new control Siemens S 7-1500 F