Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm Gtodpfehlnzkex Ahyow table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: used, Single-Column Eccentric Press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture: 1962 Pressing force: 63 tons Throat depth: 260 mm Table size: 630 x 530 mm Table opening: Ø 210 mm Ram area: 315 x 260 mm Gjdpfx Ask S Htxohyjtw Adjustable ram stroke: 8–100 mm Ram adjustment: 63 mm Ram shank bore: Ø 40 mm, with clamping piece Installation height: max. 450 mm Strokes per minute: 115 spm Air requirement: min. 4.5 bar Motor power: 4 kW Electrical connection: 380 Volt, 50 Hz Table height above floor: approx. 750 to 900 mm - Electric stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination via WEINGARTEN friction-threaded clutch with TDC safety - Front crankshaft support bearing - Press table height adjustable via 2 threaded spindles - Manual central lubrication system - Free-standing electrical cabinet - UVV (accident prevention regulations) for manual loading operations Space requirements (L x W x H): 1750 x 1600 x 2430 mm Weight: 4.5 tons In good condition

Condition: used, Hydraulic workshop press, broaching press, keyway broaching press MaVo Type 5t-20 hydraulic workshop press Used for broaching keyways in through holes. Press force 5 tons (at 100 bar hydraulic pressure) Column width 770 mm Cylinder stroke 220 mm Distance from threaded piston rod to table crosshead max. 900 mm Pressing speed (downward ram): approx. 11.5 mm/sec. = 220 mm in 19 seconds Pressing speed (upward ram): approx. 24.5 mm/sec. = 220 mm in 9 seconds. Gtodpfx Ahewki Apjyow Motor power 5.5 kW Power supply 400 volts, 50 Hz - 2-hand control (2 buttons for down, 1 button for up) - HAWE hydraulic pump, type K5/3 (also delivers 400 bar, but the pump is very, very loud) - Threaded connection on the piston rod: M42 x 1.5 mm external thread - 1 screw-in extension, approx. 290 mm, for the piston rod with M42 x 1.5 mm internal thread - 1 screw-in extension, approx. 250 mm, for the piston rod with M42 x 1.5 mm internal thread - 2 ram extensions for insertion into the screw-in extension, 110 and 130 mm long - 2 support plates - Very sturdy steel construction made of 140 mm double I-beam - Durability of the steel construction probably 40 tons. or more - Mobile with pallet truck Space requirement: L x W x H 1200 x 930 x 2280 mm Weight: 485 kg

Condition: excellent (used), Year of construction: 1997, Manufacturer: AMADA Europe S.A. Model: HFB 80 Year of manufacture: 1997 Serial number: HFB0 80 25 R970112 Pressing force: 800 kN Maximum stroke: 200 mm Gtedpfxox H Sl Ss Ahyjw Power supply: 415 V / 50 Hz Number of phases: 3 Rated current: 171 A Machine weight: 5750 kg

Year of construction: 2021, condition: like new (used), Type: PX 30530 Serial number: 12932 Year of manufacture: 2021 Bending length: 3050 mm Pressing force: 320 t Maximum pressure: 280 bar Gedpfoyhdrrjx Ahyjtw Motor power: 18.5 kW Oil tank capacity: 400 l Weight: 14,700 kg

Condition: excellent (used), selection of AMADA PROMECAM press brakes for sale ranging from 50 tonne plus call or email for inquiries Gtsdpfx Ahsyryqljyew

Condition: good (used), Year of construction: 1990, Hydraulic press Manufacturer: JOSSI Type: HP 5N Year approx. 1990 Press force max: 5 t (50 kN) Pressure: 200 bar Installation height: 120 mm Throat depth: 105 mm Max. piston stroke: 90 mm Ram mounting: 14 mm. Two-hand and foot operation. Total weight incl. hydraulic tank: 150 kg. In good condition. Gtjdpfjyn Euuex Ahysw

Year of construction: 2023, condition: used, machine/vehicle number: B1703I0727, Press force: 500 kN, stroke: max. 215 mm, overrun time: max. 117 ms, overrun distance: max. 15 mm, machine weight: 5,500 kg Gjdpeyn Nh Ssfx Ahyetw

Condition: good (used), Year of construction: 1980, In good technical condition. Year of manufacture: 1980 Gtodpfx Ajytb Dpshysw

Year of construction: 2019, condition: like new (used), functionality: fully functional, Technical Specifications * Machine Type: Cortazar Press * Pressure: 5000 ton/m² * Useful Dimensions: 4700 × 1820 mm * Number of Cylinders: 10 * Plate Type: Pre-drilled stainless steel plates with vacuum system * Press Opening: 300 mm * Cylinder Diameter: 500 / 480 mm Gtjdpfxeyt Rf Aj Ahyow * Number of Plates: 2 * First Height: 1370 mm * Last Height: 1570 mm * Total Force: 5000 tons * Filter Belt: Yes * Integrated Water Tank: Yes * Loading and Unloading System: Automatic * Overall Dimensions: 5355 × 2500 mm * Usage: 546 pressing cycles

Condition: excellent (used), pressure 16 t Gtsdpsyrhmhsfx Ahyjw weight of the machine ca. 16 t

Condition: used, Year of construction: 1989, Make and model: Bruderer BSTA 25 EL Gedpfxjyrf Aaj Ahyotw Year of manufacture: 1989 Nominal capacity: 250 kN, 25 tons Max. number of strokes: 100/1350 Adjustable stroke: 13, 16, 19, 25, 32, 38 mm Table dimensions: 640 x 530 mm Passage between the supports: Longitudinal 640 mm; Lateral 220 mm Fitted with roll feeder BBV 190/85 on right hand side. Max width of strip: 160 mm Feed length: variable up to 85 mm max Optional: Sound insulating cabin Oil pump. Heat exchange oil cooler. Front and rear safety guards. Fitted on 4 spring feet. Slide/Ram adjustment: 51 mm Documentation included. Press weight cca. 5000 kg.

Condition: used, pressure 150 t Table dimensions 1000 x 360 mm Gtjdpfxeyuqk Uo Ahyjw voltage 400 V

Condition: used, pressure 150 t Table dimensions 1000 x 360 mm voltage 400 V Gtedoyuqdhjpfx Ahyew

Condition: used, Year of construction: 1962, pressure 080 t throat 300 mm stroke 8 - 112 mm no. of strokes 60 /min distance table/ram, max. stroke up, adjustment up 467 mm table surface area 710 x 560 mm hole in the table 240 x 115 mm table height over floor 800 mm ram surface 400 x 315 mm ram adjustment 80 mm power requirement 7,5 kW weight 5,1 t dimensions (WxDxH) 1,4 x 1,9 x 2,7 m SPECIAL DEAL as is where is, WITHOUT additional work free loaded to truck Gtodpfx Ahsyq Smioyow

Condition: used, Year of construction: 1966, pressure 035 t throat 225 mm stroke 8 - 100 mm no. of strokes 110 /min distance table/ram, max. stroke up, adjustment up 400 mm table surface area 580 x 460 mm hole in the table 250 x 150 mm table height over floor 700 mm table adjustable 230 mm ram surface 355 x 120 mm ram adjustment 70 mm power requirement 2,2 kW weight 1,5 t dimensions (WxDxH) 1,0 x 1,5 x 2,05 m SPECIAL DEAL Gtsdpfxeyq Smcj Ahyow as is where is WITHOUT putting into operation / WITHOUT additional work free loaded to truck

Condition: used, Year of construction: 1962, pressure 060 t throat 220 mm stroke 6 - 94 mm no. of strokes 115 /min distance table/ram, max. stroke up, adjustment up 340 mm table surface area 680 x 400 mm hole in the table 120 x 70 mm table height over floor 750 mm passage to the back 290 mm Gjdpsyq Sl Sofx Ahyotw ram surface 240 x 240 mm ram adjustment 57 mm power requirement 3,7 kW weight 2,8 t dimensions (WxDxH) 1,5 x 1,5 x 2,2 m SPECIAL DEAL as is where is, WITHOUT additional work free loaded to truck

Condition: used, Year of construction: 2005, pressure 30 t Stroke 190 mm distance between columns 440 mm side window 450 mm daylight (max. stroke up, adjustment up) 350 mm table surface area 595x450 / 440x595 mm table height over floor 725 - 900 mm table adjustment range 175 mm ram surface 90 mm power requirement 0,5 kW Weight 1,20 kg Gtodpeyfwvrefx Ahyow dimensions (WxDxH) 1,5 x 1,0 x 2,9 m SPECIAL DEAL as is where is, WITHOUT additional work free loaded to truck Basic unit power pack K 30.181-190.10 with stroke limitation, anti-rotation protection, universal underframe UUM 1-200.031, adjustable working height Total stroke 190 mm / power stroke 10 mm

Condition: used, Year of construction: 1978, pressure 050 t Gtsdpfxjvut E De Ahyow throat 250 mm stroke 8 - 120 mm no. of strokes 100 /min distance table/ram, max. stroke up, adjustment up 400 mm table surface area 650 x 515 mm hole in the table 115 mm table height over floor 790 - 1020 mm table adjustable 230 mm ram surface 390 x 180 mm ram adjustment 70 mm power requirement 2,0 kW weight 2,6 t dimensions (WxDxH) 1,1 x 1,4 x 2,2 m SPECIAL DEAL as is where is WITHOUT putting into operation / WITHOUT additional work free loaded to truck

Condition: good (used), Year of construction: 1985, Manufacturer: RADAELLI Model: 1000/S2 Year: 1985 Condition: Used Stock number: 0388 Gedpjyrigpofx Ahyetw Press force: 1000 tons Press points: 2 Ram dimensions: 2,820 x 2,200 mm Table size: 3,150 x 2,200 mm Ram stroke: 500 mm Die height at BDC: 1,000 mm Ram adjustment: 190 mm Strokes per minute: 15 spm Pneumatic cushion present

Condition: excellent (used), Year of construction: 2001, Manufacturer: ROVETTA Model: S4-800 Year: 2001 Condition: Used Stock number: 0392 Builder: Rovetta Gtedpfxoyq Tdpj Ahyew Slide force: 800 tons Number of driving points: 4 Slide stroke: 700 mm Slide adjustment: 350 mm Strokes per minute: 10-24 Die height (low stroke, high slide adjustment): 1,100 mm Usable distance between front posts: 4,200 mm Bolster table size: 4,000 x 2,000 mm Slide dimensions: 4,000 x 2,000 mm Movable table height: 600 mm Side window size: 3,400 x 1,900 mm Number of cushions: 1 Blankholder cushion - total force: 150 tons Lower blankholder cushion stroke: 250 mm Lower blankholder working area: 1,500 x 1,000 mm.

Condition: excellent (used), Year of construction: 2001, Manufacturer: ROVETTA Gtodpfoyq Tdiex Ahyjw Model: S4-1500 Link Drive Year: 2001 Condition: Used Stock number: 0391 Manufacturer: Rovetta Number of strokes: 4 Ram force: 1500 tons Ram stroke: 763 mm Ram adjustment: 400 mm Daylight (bottom dead center, ram up): 1,200 mm Distance between front uprights: 5,700 mm Die bed dimensions: 5,500 x 2,500 mm Ram dimensions: 5,500 x 2,500 mm Moving table height: 600 mm Side window size: 3,400 x 1,900 mm Main motor power: 319 kW Blankholder (total force): 150 tons Blankholder stroke: 250 mm Blankholder working area: 2,000 x 1,200 mm Strokes per minute: 8-24

Condition: new, Year of construction: 2025, pressing force: 100 t, stroke length: 400 mm, - Cylinder stroke 400 mm - Working width 1010 mm - Cylinder is movable - Can be operated electrically or manually Gtjdpsgp Dc Rsfx Ahyew - Pressure indicator - Emergency stop - 400V

Condition: like new (used), Year of construction: 2023, overall weight: 1,050 kg, working width: 1,000 mm, pressing force: 100 t, stroke length: 400 mm, Equipment: emergency stop, – Year of manufacture: 2023 (lightly used) – Capacity: 100 tons – Cylinder stroke: 400 mm – Working width: 1000 mm – 2 speeds – Pressure gauge Gsdjyupu Ejpfx Ahyjtw – Emergency stop – 400V

Year of construction: 2007, condition: ready for operation (used), overall weight: 11,000 kg, total height: 2,850 mm, product length (max.): 4,550 mm, number of axes: 4, General Data Machine weight 11000 kg Measurements height 2850 mm Dimensions Machine Length 4550 mm Gsdpjx D Diuofx Ahyotw Main Drive Number of axis 4 Bending length 3100 mm This 4-axis ERMAK CNC HAP 3100x200 was manufactured in 2007. A robust hydraulic press with a press capacity of 200 tons and a bending length of 3100 mm. It operates with an Ermak ER70 CNC control system and has a motor power of 15 kW. Ideal for heavy-duty bending tasks. Machine dimensions are 4550 × 2250 × 2850 mm, weighing 11,000 kg. Contact us for more information about this machine. Application Types Bending