Used Mechanical Press for sale (17,536)

Condition: repair required (used), Year of construction: 1990, functionality: not functional, power: 45 kW (61.18 HP), Briquetting machine, with some spareparts and 45kw motor. Dedpfxstur Ewe Afnokh

Condition: used, Year of construction: 1985, Technical details: Punching capacity: 40 kN air pressure - required: 8 bar ram stroke - adjustable min/max: 6 - 50 mm ram adjustment: 50 mm no. of strokes: 70 - 400 Hub/min Table dimensions: LxB: 480 x 445 mm hole in table: LxB: 250 x 112 mm slowing-down time: 80 ms bei 450 U/min. clamping surface ram: LxB: 420 x 345 mm ram hole: Ø 40 x 230 mm voltage: 380 V Dodpju Icwgsfx Afnokh control voltage: 220 V frequency: 50 Hz total power requirement: ca. 19 kVA (ca. 7,5 KW) weight of switch cabinet: 0,3 t machine weight ab.: 4000 kg 40t punching press without roll feed/conveyor belt system Operation via control panel / two-hand operation Operation: manual / automatic *

Condition: good (used), Year of construction: 2000, Capacity Kg Djdpfx Afsyc R Uijnokh 15000 Table Length 400 mm Table Width 300 mm Hole in table 150 mm Working height 280 mm Throat 2170 mm Stroke 50 mm Ram adjustment 4 - 80 mm Hydraulic Clutch CE-Safety 2e hand opperator system Adjustable stroke / ram  Full set books / drawing / CE-Mark Length:1500mm Width:1500mm Height:2100mm Weight:1500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 2000, table width: 300 mm, table length: 400 mm, pressing force: 15 t, Hydraulic clutch CE-Safety 2e hand opperator system Adjustable stroke / ram  Full set books / drawing / CE-Mark Note in the Neck / Throath machine is repaired ! Only EUR 5500 Dksdjyc R Nmopfx Afnsh Capacity Kg: 15000 Table Length: 400mm Table Width: 300mm Hole in table:150mm Working height:280mm Throat: 2170mm Stroke: 50mm Ram adjustment:4 - 80mm Length: 1500mm Width: 1500mm Height: 2100mm Weight: 1200kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1987, fabric-no. 202 395 working length 2550 mm output 2000 KN tracking travel 13 mm safety distance 176 mm Dsdpfxjq Awh Ro Afnskh

Condition: excellent (used), Year of construction: 1995, Decoiler Max. width 350 mm Dkedpfx Afsx Sx Spjnoh Clamping area coil internal 470 - 530 mm Coil diameter 1500 mm Work load 2000 Kg Straigtner Width 350 mm Roll diameter 30 mm Number off rolls 9 units In feed rolls 2 units In feed roll diameter 90 mm Working speed 40 M/Min Max. thickness 6 mm at 240 N/mm2 Max. Thickness 5 mm at 400 N/mm2 Length:3200mm Width:1500mm Height:2200mm Weight:3700kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Crimping pliers, crimping pliers, cable lug pliers, mechanical crimping pliers, pressing jaws, pressing tool for cable end sleeves, wire end sleeves, cable lugs, hand crimping pliers, sleeve pliers, clamp sleeve pliers -Manufacturer: WMW, hand crimping pliers type PH 2.5C -Crimping: of cable lugs and cable connectors -Pressing force: 25.0 N -Pressing stroke: 15 mm Dedpeb A S Uvsfx Afnskh -Transport case: incl. accessories, see photo -Quantity: 1x crimping pliers available -Price: per piece -Dimensions of pliers: 600/180/H25 mm -Total weight: 3.2 kg

Condition: good (used), Crimping pliers, crimping pliers, cable lug pliers, mechanical crimping pliers, pressing jaws, pressing tool for cable end sleeves, wire end sleeves, cable lugs, hand crimping pliers, sleeve pliers, clamp sleeve pliers Dsdpfx Afjwup Efenekh -Manufacturer: Klauke, hand crimping pliers type K05 -Crimping: of cable lugs and cable connectors -Standard version: 6 - 50 mm -Dimensions: 390/140/H50 mm -Weight: 1.1 kg

Condition: used, Year of construction: 2016, pressure 20.0 t chamfer lenght 850 mm distance between columns 850 mm back stop - adjustable 375 + 400 mm stroke of upper beam 196 mm dayligth 470 mm ajustment speed 200 mm/sec table height ca. 900 mm total power requirement 5.0 kW weight of the machine ca. 2500 kg New price ~ 85.000 euros well-kept / very good condition (!!) with electromechanical direct drive (servo motor + ball screws) Machine is operated without hydraulic oil - in checked condition - machine video - ?v=foxzKIA7vX8 Description : High performance, fast travel speeds and the best ergonomics this bending machine to a perfect tool in terms of productivity and Accuracy. This allows an unrivaled high productivity in the field of small and middle bending parts can be achieved, since even complicated bending sequences several stations can be processed very quickly. A large number of different and universally divided tools are possible an almost unlimited variety of areas of application. Furnishing : - Stable machine frame for standing and seated operation - Deformation-optimized press beam - Highly dynamic, electromechanical. Direct drive (servo motor + ball screws) - CNC control Panasonic Toughbook incl. USB and WIFI connection - CNC controlled axes : Y + X + R + Z1 + Z2 - CNC control unit in front right, swivelling - Inductive length measuring system with temperature compensation - Ergonomic machine design - AMADA system upper tool holder - AMADA system lower tool holder - 1x brand new universal tool set (complete) - front safety device (DUAL Laser/Iris Rapid Bend) - Rear security cover - Laterally pivoting protective doors - 2x foot switch, for standing and sitting operation - Support tables comfort (front) - User manual (original) Dsdpfxoxacifj Afnekh * Special accessories included: - 4-axis backgauge (axes X+R+Z1+Z2) * Speed X axis .. 250 mm/sec * Speed R axis .. 600 mm/sec * Z axis speed .. 1100 mm/sec * Positioning accuracy X axis .. 0.04 mm * Positioning accuracy R axis .. 0.06 mm * Travel X axis .. 375 + 400 mm * Travel R axis .. 180.0 mm

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, ram adjustment: 100 mm, table length: 600 mm, installation height: 1,900 mm, stroke adjustment: 130 mm, overall weight: 19,000 kg, pressing force: 160 t, height adjustment type: electric, power: 11 kW (14.96 HP), punching force: 160 t, input voltage: 200 V, Equipment: documentation/manual, safety light barrier, Manufacturer: AIDA Type: NC2-160 Push force: 160t Year of manufacture: approx. 1991 Stroke length: 130mm Distance above table: (adjustable) 285-335mm Table size: 1900x600mm Bear size: 1360x585mm Electric power: 3x200V(!!), 15kW - Japanese standard Net weight: 19000kg Size: 2140x2210x3175mm Dedpju D Dhxefx Afnokh Automatic greasing system. Optionally sheet feeder winder and straightener.

Condition: like new (used), Year of construction: 2002, functionality: fully functional, Manufacturer: NAVA Model: 2MI1600DE/SE Year: 1998 Condition: Used Stock number: 0367 Pressing force: 1,600 tons Number of pressing points: 4 Ram stroke: 1,200 mm Upper punch stroke: 1,500 mm Ram size: 4,500 x 2,500 mm Table size: 4,500 x 2,500 mm Blankholder cushion – total force: 400 tons Lower blankholder cushion stroke: 500 mm Dsdpex R U Nuefx Afnokh Withdrawable carriage: Present, front side

Condition: used, Year of construction: 1979, Technical details: pressure: 250 t slide stroke: 40-160 mm throat: 545 mm ram adjustment: 110 mm Table dimensions: 1250x800x100 mm biggest distance between table & ram: 670 mm drawing capacity: 16 to table height over floor: 1000 mm Dsdpfeu Nfinox Afnekh surface area of ram: 900x670x100 mm distance between columns: 500x400 mm total power requirement: 23 kW weight of the machine ca.: 16,6 t dimensions of machine: 2,8x1,4x3,7 m dimensions electric cabinet LxWxH: 1,15x0,6x2,1 m Ejector and counter holder force: 16t Table size with 4x T-slots parallel running (1250x800x100mm) Ram plate with 4x T-slots radially running Data at bottom dead center UT: largest stroke: 510mm smallest stroke: 570mm Accessories: - Steel plate 1170x860x80mm *

Condition: used, Manzoni 40 Ton high speed press 150/300 strokes Dsdpokn Hk Tjfx Afnskh Used - bargain

Condition: used, Manzoni 60 Ton high speed press 110/308 strokes Used - Bargain Djdpokn Hqgjfx Afnekh

Condition: good (used), Year of construction: 1984, Automatic Press Factory Warszawa-Włochy Dksdpfow Uaxzex Afnoh TYPE PXS 100 Eccentric Press, pressure 100 t Year of manufacture: 1984

Condition: ready for operation (used), For sale: a very solid and fully operational Constantin Hang 150-06, the industry standard for press-fitting and crimping ring binder mechanisms onto folders, binders, and covers. Specifications and features: • Suitable for 2-ring and 4-ring mechanisms • Powerful mechanical eccentric press • Very robust German construction (cast iron) • Foot pedal operation for safe and fast working • Complete and ready for immediate use • Machine presses and crimps the legs of the ring mechanism in a single operation • Ideal for binderies, file manufacturers, and office supply production Currently set up for 2-ring mechanisms (80 mm), but can be easily adjusted for other mechanisms. Dodpfx Afox A Ivvonskh Technical data: • Manufacturer: Constantin Hang • Model: 150-06 • Serial number: 102160 • Country of origin: Germany Condition: Good, clean, and working condition. Can be demonstrated immediately.

Condition: used, Punching Machine MUHR & BENDER - MUBEA Model KL 350 / 203 Machine No. KL3509864 Year of manufacture: 1998 Punching force: 35 tons Throat depth: 200 mm Ram stroke: 22 mm Capacity: Ø 28 mm in 10 mm sheet (at 450 N/mm²) Ø 23 mm in 12 mm sheet (at 450 N/mm²) Ram plate: 265 x 70 mm Ram plate thickness: 25 mm outside / 50 mm in the center Table plate: 285 x 250 mm, thickness 40 mm Table cutout: 115 x 85 mm Drop-through opening in table cutout: 115 x 25 mm Dsdpoxf Utajfx Afnokh Installation height: 125 mm (with table and ram plate) Number of strokes: single stroke via foot switch Motor power: 1.5 kW Power supply: 400 Volt, 50 Hz - Electric foot switch for stroke activation - Manual lever search device for punch movement - Special tool as punching tool Space required (L x W x H): 800 x 800 x 400 mm Weight without tool: 340 kg Weight with tool: 370 kg Good condition

Condition: used, Single column eccentric press PELS - RICHTER type PEKR 125 Machine. No. 20684 Year of construction 1967 pressure force 125 ton. throat 430 mm table size 1100 x 750 mm ram area 890 x 650 mm table opening Ø 400 mm stroke adjustment 6 to 115 mm ram adjustment 100 mm installation height largest stroke top max. 450 mm Clamping spigot bore Ø 50 mm Stroke rate 60 strokes/min. Table height above floor 900 mm motor power 7,5 kW Mains connection 380 Volt, 50 Hz - Overload protection by crushing plate in ram - Compressed air clutch-brake combination DESCH - ram weight balancing cylinder - manual ram adjustment - two-hand operation - cam gear Dedpfx Afefim Thenokh - Grease central lubrication Vögele - stroke counter Space requirement L x W x H 2300 x 1450 x 3030 mm weight approx. 10 ton. good condition

Condition: used, Single-column eccentric press WEINGARTEN type ER 63 Dkedpelb I Dzofx Afneh Machine. No. 52A / 63 Year of construction 1963 Pressure capacity 63 ton. throat 280 mm Table surface 630 x 530 mm ram stroke adjustable 8-100 mm ram adjustment 63 mm Stroke rate 65 strokes / min. Motor power 4 kW Mains connection 380 Volt, 50 Hz - Clutch/brake combination with WEINGARTEN friction threaded clutch - Electric lift release via foot switch - Wheel reduction gear - Overload protection by breaker plate - Front crankshaft support bearing Space requirement L x W x H 1500 x 1100 x 2500 mm Weight 4.5 tons good condition

Condition: used, Single column eccentric press WEINGARTEN type ERV 40 Machine No. 537 / 65 Year of construction 1965 Compressive force 40 ton. throat 230 mm table size 570 x 470 mm ram surface 250 x 200 mm clamping spigot bore Ø 40 mm installation height max. approx. 520 mm Dkodpfx Asffm Hhofnjh stroke adjustment 8 - 88 mm slide adjustment travel 63 mm Stroke rate 70 strokes per minute Drive power 3 kW Mains connection 380 Volt, 50 Hz - Table height adjustment - Overload protection by crushing plate - clutch-brake combination by WEINGARTEN friction thread clutch - electric 2-hand operation and foot switch - central lubrication via hand pump space requirement L x W x H 1600 x 1150 x 2300 mm weight approx. 2,6 ton.

Condition: used, TECHNICAL DETAILS - Pressure : 4 [t] - Execution : * number of mounts : 2 - Fix table : Djdpouhakbsfx Afnekh * length : 210 [mm] * width : 210 [mm] - Press frame : fix - Hole in the table : diameter 80 [mm] - Number of punches : from 50 to 150 [p/min] - Adjustable slide : 40 [mm] - Fix travel : 27 [mm] - Max height for tooling : 148 [mm] - Passage through mounts - Longitudinal : 230 [mm] - Electric connection : 380 [Volt] - Total installed power : 0.75 [CV] - Weight : 640 [kg] - Floor space (length x depth x height) : 1100 x 1000 x 1500 [mm]

Condition: used, TECHNICAL DETAILS - pressure : 4 [t] - number of supports : 2 - fixed table dimensions : 210 x 210 [mm] - fixed press assembly - hole Ø in table : 80 [mm] - number of strokes in sharpening / cutting : 50 - 150 [c/min] - adjustable slide : 40 [mm] - fixed travel : 27 [mm] - max. height for tooling : 148 [mm] - longitudinal clearance between supports : 230 [mm] Dedpfxsuhahme Afnokh - max. part diameter in sharpening : 30 [mm] - max. part thickness in sharpening / cutting : 1.5 / 2 [mm] - voltage : 380 [V] - installed power : 1.5 [kW] - floor space : 1100 x 1100 x 1650 [mm] - weight : 500 [kg]

Condition: used, TECHNICAL DETAILS - Pressure : 4 [t] - Max. part diameter : 30 [mm] - Max. part thickness : 2 [mm] - Shocks per minute : 150 Djdpouhahajfx Afnokh - Distance between mounts : 230 [mm] - Distance between table and slide : 148 [mm] - Table diameter : 220 [mm]

Condition: used, TECHNICAL DETAILS - pressure : 4 [t] - number of supports : 2 - fixed table dimensions : 210 x 210 [mm] - fixed press assembly - hole Ø in table : 80 [mm] - number of strokes in sharpening / cutting : 50 - 150 [c/min] - adjustable slide : 40 [mm] Dodpfjuhahgox Afnokh - fixed travel : 27 [mm] - max. height for tooling : 148 [mm] - longitudinal clearance between supports : 230 [mm] - max. part diameter in sharpening : 30 [mm] - max. part thickness in sharpening / cutting : 1.5 / 2 [mm] - voltage : 380 [V] - installed power : 1.5 [kW] - floor space : 1100 x 1100 x 1650 [mm] - weight : 500 [kg]

Condition: used, TECHNICAL DETAILS - See photos Dkjdpfxeuhakho Afnjh