Used Stamping Press for sale (12,691)

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Ksdpodzqltsfx Ab Tsln Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. Kodpfx Abou Rwa Is Tsln throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, Single-column Eccentric Press MÜLLER GEFREES Type 60 SV DK (Identical to ExP60) Very lightly used eccentric press in original condition Machine No. 5250686 Year of manufacture: 1986 Nearly new condition Press force: 60 tons Throat depth: 280 mm Table surface: 740 x 560 mm Ram surface: 385 x 200 mm Through-hole in table: 300 x 200 mm Table surface (intermediate plate): 740 x 560 mm Through-hole in intermediate plate: Ø 103 mm Intermediate plate thickness: 70 mm Clamping pin bore: 40 mm Table height above floor: 815 mm (with intermediate plate) Installation height, max.: 275 mm (with intermediate plate) Installation height, max.: 345 mm (without intermediate plate) Stroke adjustment: 10–90 mm Ksdpfoi A A Tbsx Ab Teln Ram adjustment: 60 mm Strokes per minute: 100 Motor power: 3 kW Drive: 380 Volt, 50 Hz - Mechanical rotary wedge clutch with pneumatic actuation - Spring-loaded single-jaw brake, controlled by cam disc - Stroke release via pneumatic footswitch - Overload protection with breaking plate in the ram - Table height adjustment via 2 threaded spindles - Manual central lubrication system by BEKA Schmiertechnik - Operating manual and pneumatic diagram included Space requirement (L x W x H): 1400 x 1100 x 2200 mm Weight: 3.4 tons In very good, almost new condition

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Pressure capacity 40 ton. Kodpjtx E Rqefx Ab Toln throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm ram surface 250 x 200 mm Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: used, Single-column eccentric press WEINGARTEN type ER 63 Machine. No. 52A / 63 Year of construction 1963 Kjdpfolb I Dzox Ab Tjln Pressure capacity 63 ton. throat 280 mm Table surface 630 x 530 mm ram stroke adjustable 8-100 mm ram adjustment 63 mm Stroke rate 65 strokes / min. Motor power 4 kW Mains connection 380 Volt, 50 Hz - Clutch/brake combination with WEINGARTEN friction threaded clutch - Electric lift release via foot switch - Wheel reduction gear - Overload protection by breaker plate - Front crankshaft support bearing Space requirement L x W x H 1500 x 1100 x 2500 mm Weight 4.5 tons good condition

Condition: used, Year of construction: 2001, functionality: fully functional, Technical Specifications Press capacity: 800 kN (80 tons) Stroke rate: 60 – 320 strokes per minute (SPM) Stroke adjustment: 8 – 80 mm Ram adjustment (shut height adjustment): 80 mm Table size: 830 × 700 mm Bolster plate thickness: 80 mm Table opening: 500 × 200 mm Strip feed height over table: 120 mm Ram area: 500 × 400 mm Kodpfxeyidnye Ab Tsln Ram bore: Ø 50 × 90 mm Ram centering bore tolerance: 30 H7 mm Precision guided ram, multi-roller guidance system. Main motor power: 23 kW Drive system: Flywheel drive with planetary gearbox and pneumatic clutch/brake combination. Machine weight: approx. 8000 kg Gripper Feed Schaal SZV 3: Feed length: 4 – 150 mm Strip width: 10 – 270 mm Strip thickness: 0.1 – 4 mm We also have on stock Schaal SEP 80 with SWV3E 300 mm wide Servo Feeder. Unidor Control, Machine and Operator Safety. Full Technical Documentation in German including Parts list and Technical drawings.

Condition: good (used), Baier Geba Hot Stamping Press This machine is in very good condition and ready to use. This machine is from the popular hot stamping manufacturer Gebrüder Baier KG, manufactured in Germany. Description The Baier Geba hot stamping press is a press for hot stamping, embossing, and die-cutting paper and plastics. It’s a useful device in any advertising agency or digital printing house. The manually operated pressure is powered by only 230V. A powerful pressure with adjustable pressure ensures repeatability and very high pressure of the die against the material. The machine features a worktop with a slide-out function, adjustable embossing depth, and a heating plate with a thermostat. Specifications: Heating temperature control Heating plate pressure mechanism: mechanical Press force: 5000 kg Power consumption: 9000 W Kodpfxoyi Dcto Ab Tjln Power supply: 230 V Machine weight: 300 kg Plate size: 32 x 21 cm.

Condition: used, Prägepresse / Hot Foil Stamping Press Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Kljdpfx Abst Drnxj Ton Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, machine/vehicle number: 24118, Kniehebelprägepresse - Embossing Stamping Press Krause KHP Prägefläche / Stamping size: 350 x 400 mm Sehr guter Zustand / Beautiful condition Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect Ksdeut Tkgspfx Ab Teln On Stock Emskirchen / Nürnberg - Can be test

Condition: used, machine/vehicle number: 21035, Heißpräge - Kniehebelprägepresse - Embossing Hot Stamping Press Krause FNPSerial-No. 4798 Klsdpfx Aboh Ayg Us Tjn Stamping size: 550 x 400 mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, machine/vehicle number: 18040, Kniehebelprägepresse - Embossing hot stamping press Hans Schilling HSMSerial-No. 18040 Online-Video-Inspection by Skype-Video Kedpfeh Axf Hex Ab Tsln We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Antike Kniehebelprägepresse / Antique Embossing Hot Stamping Press Karl Krause KHP Baujahr / Year ca. 1930 - Serial-No. 48090 Prägefläche / Embossing Size max. 340 x 430mm Beheizung mit Gas / Heating with Gas Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test Kledpswtw E Dsfx Ab Tjn

Condition: used, Kniehebelprägepresse - Embossing Stamping Press Krause KHP Prägefläche / Stamping size: 350 x 400 mm Sehr guter Zustand / Beautiful condition Kjdpfxevi Hh Io Ab Toln Online-Video-Inspection...

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Kedpfx Abshlnzkj Teln Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: used, Single-Column - Eccentric Press AMBOLD Type PEEV 25.2 Machine No. 11734 / Year of manufacture: 20 Press force: 25 tons Throat depth: 200 mm Table size: 520 x 400 mm Ram area: 155 x 155 mm Through hole in table: 185 x 155 mm Stroke adjustment: 4–80 mm Ram adjustment distance: 40 mm Max. installation height: 270 mm (maximum stroke at BDC, table at lowest position) Clamping shank bore: Ø 32 mm Table height adjustment: approx. 150 mm Ram strokes: 160 strokes/min Motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - Pneumatic clutch-brake combination ORTLINGHAUS Kodetx E N Tjpfx Ab Tsln - Press safety valve HERION - Press control PILZ - Electric foot switch and two-hand control - Height-adjustable press table via 2 threaded spindles - Automatic central lubrication VOGEL - UVV according to VBG 7n 5.1 for manual loading - Free-standing control cabinet L x W x H = 600 x 310 x 1500 mm Required space L x W x H: 1450 x 1000 x 1850 mm Weight: 1.9 tons Very good condition

Condition: refurbished (used), Year of construction: 1992, functionality: fully functional, machine/vehicle number: 131 644, Attention: machine has been 2022 completely mechanically and electrically retrofitted before delivery press force: 1000kN stroke: 30 - 100mm slide adjustment: 80mm speed: 50 - 300/min shut height. 350mm table dimensions: 1080 x 800mm slide dimensions: 900 x 620mm new electrical controller SIEMENS S7 1500 Kledpfxefn Affo Ab Ten

Condition: ready for operation (used), Hertweck P4 hydraulic press stamp press You are welcome to come by for a viewing. We are happy to organize a cost-effective shipping company for you! You will receive a proper invoice. For foreign customers, a net invoice can also be issued. A valid VAT identification number is required. Subject to prior sale. Visit our shop and take a look at our other offers. Klsdpfsvux Spjx Ab Ten The company names and trademarks given are the property of their owners and are used only to identify and describe the products. Deviations from technical data and errors in the description of the article can occur and are reserved.

Condition: good (used), High-Speed punching press - BSTA 18 /600 Stroke power 180 KN (18 tons) Overhauled by Silicon in good working condition Adjustable speed 60 - 600 (strokes) per minute up to 10 strokes in one second Equipped with synchronized double rolls BBV120 feed for strips widths from max. 120 mm Klsdpfxj Udtye Ab Ten Feed pitch up to max. 60 mm adjustable, highly accurate With stroke counter with programmable auto stop and speed counter Machine complete weight approx 1.5 tons Maximum strip width 120 mm Maximum strip thickness 2.2 mm Maximum feed pitch 60 mm Indexing per minute, infinitely variable 60 - 600 strokes Automatic in feed Operators instruction manual More high speed presses on stock made by Bruderer models BSTA 18, 20, 30, 200, 50 and Schaal and Mabu presses

Condition: good (used), Karl Krause Hot Stamping press Klsdjx N Dxvspfx Ab Ten Manufactured by Karl Krause, Germany, The machine is fully operational, after modernization of the control system. The work table is moveable. The device was purchased from a school workshop and has not been used in production. Power supply: 230V Heating plate size: 400x275mm. Weight: approx. 600kg.

Condition: excellent (used), machine/vehicle number: 46131, Stamping surface with heating head: HKAC max. 100 x 125 mm // HKBC max. 140 x 230 mm Stamping pressure at 6,5 bar with: 1 Zylinder ca 400 daN (kp) // 2 Zylinder ca 800 daN (kp) Readjustable stroke, dep. on pressure producer: 0-40 mm / 0-100 mm Max. passage height without/with sliding table: 300 mm / 275 mm Readjustable foil advance: 0-230 mm Max. foil width: 140 mm Heating voltage: 220 V / 50 Hz Heating capacity with heating head: HKAC 540 W // HKBC 900 W Klsdsx I Nfrjpfx Ab Tsn Temperature measurement by means of: Fe-Ko Max. output, hourly cycles: ca 4000

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, Gietz FSA 790 EFF high speed foil stamping , embossing and die cutting machine Offered fully reconditioned by exclusive Gietz UK distributor Max format 790 x 560 mm : max speed 6,000 sheets / hr Top EFF specification Kjdpfx Abex Ezkuj Tsln High speed MABEG suction feeder : 6 heating zones : 3 x electronic servo longitudinal foil feeds : 3 x transverse foil feeds : 3 line hologram capability : non stop delivery

Condition: ready for operation (used), Met elektrische achteraanslag Ponscapaciteit: 70 ton Dia x plaatdikte: Ø 28 x 20 mm Maximale slag: 80 mm 40 str / min Keeldiepte: 300 mm Werkhoogte: 1065 mm Maximale snijdikte in plaat: 20 mm Bladlengte: 455 mm 90°-snede: 130 x 130 x 13 mm 45°-snede: 90 x 90 x 10 mm Op maat gesneden rond/vierkant: 45 mm Elektromotor (vermogen): 7,5 kW Lengte: 1800 mm Diepte: 1200 mm Hoogte: 2000 mm Gewicht: 1650 kg Kodpfx Abjxgv E To Teln

Condition: ready for operation (used), - invoersysteem voor plat- en hoekstaal - met toevoerwagen en materiaalklem - Vacon 110 software CNC-besturing Hydraulische schaar voor vlak staal VPS 2200 cap: 220 ton maximale lengte: 15 200 mm breedte/dikte: 500/25 mm hoek: +/- 45° Hydraulische hoekschaar voor staal VHS 2400 cap: 240 ton maximale lengte: 15 200 mm 200 x 200 mm / 16 mm Hydraulisch ponsen VPO 1000 cap: 100 ton ponsdiameter/dikte: 57/15 mm of 32/25 mm 4 ponsunits voor vlak staal (Verticale positie) 1 ponseenheid voor hoekstaal (horizontale positie) incl. gereedschap Hydraulische teller VNI 1/36 1 codeerschijf 36 tekens tekenhoogte x diepte: 10 x 1 mm Kodjwlkw Dspfx Ab Tsln Hydraulisch aggregaat VHA 37 37 kW - 250 bar

Condition: used, Year of construction: 2020, functionality: fully functional, For sale: Metal Stamping Press ALP-25C (25T, 2020) Condition: Virtually unused, like new. Manufacturer: JINAOLAN Machinery (China) Model: ALP-25C Year of manufacture: 2020-11 A compact and reliable mechanical eccentric stamping press designed for forming, punching, and stamping various metal parts. Technical specifications: Nominal capacity: 25 T Stroke: 45 mm Stroke rate: 145 strokes/min (SPM) Max. die height: 180 mm Height adjustment: 35 mm Ram working area: 170 × 150 mm Bolster area: 370 × 240 mm Country of origin: China Applications: The ALP-25C press is suitable for: Klsdpfxexmwnio Ab Tsn stamping, cutting, bending, and forming metal parts; small pressing operations in tool, metal structure, and automotive parts manufacturing; working with thin and medium-gauge sheet metal. If you have any further questions, please feel free to contact us.

Year of construction: 2021, condition: excellent (used), For sale: Metal Stamping Press ALP-25J (25T, 2021) Kljdpfx Asxm U S Sob Ton Condition: Virtually unused, like new. Manufacturer: JINAOLAN Machinery (China) Model: ALP-25J Year of manufacture: 2021-04 A compact and reliable mechanical eccentric stamping press designed for forming, punching, and stamping a wide range of metal components. Technical specifications: Nominal capacity: 25 T Stroke: 100 mm Stroke rate: 100 strokes/min (SPM) Max. die height: 260 mm Height adjustment: 55 mm Ram working area: 560 × 370 mm Bolster area: 250 × 220 mm Country of origin: China Applications: The ALP-25J press is suitable for: - Stamping, cutting, bending, and forming metal components - Small press operations in tool, metal structure, and automotive part manufacturing - Working with thin and medium-thickness sheet metal If you have any further questions, we will be happy to answer them.