Cone crusher

KHD Calibrator 1300H

Year of construction: 1990, condition: repair required (used), Mobile jaw crushing system, operating hours approx. 10.000, engine Caterpillar 6 cylinders with generator set approx. 35 KVA, year of construction approx. 1990, jaw crusher KUE-KEN (KK114 inlet 1140 x 750 mm) incl. magnetic tape (iron separator), total weight 48 tons on semi-trailer chassis. Hsdpfx Agehz Dmgezsg Condition: Motor and conveyor systems run perfectly, only the drive shaft of the crusher is defective (damage approx. € 17.000)

Condition: new, functionality: fully functional, fuel type: gasoline, overall weight: 2,700 kg, Year of construction: 2025, operating hours: 1 h, PROMAX SCREEN DRUM T 2000 SPECIFICATION OF THE MACHINE General dimensions Transport length: 5.92 m Operating length: 8.1 m Width: 2.185 m Height: 2.65 m Weight: 2850kg capacity Hopper: 1.4 m3 Fuel tank: 18 liters Engine: Mosa Type: GE13000 Power: 13KVA fuel: Gas Fuel consumption: 2.5L - 3.9L per hour TASK BUNKER Gearbox: Motovario B083 R105-1 90B5 Electric motor: Hansler 0.75 kW, 6-pole, B5 IE3 Belt width: 450 mm Band length (drum center): 2.28 m Band: EP250 2-layer C15 Chevron 3+1.5mm Variable speed drive Hederhzmtepfx Agzog Fines conveyor Transmission: Motovario NMRV 90 R7.5-1 100B14 Electric motor: Hansler 2.2 kW, 4-pole, B14 IE3 Band width: 1600 mm Belt length (drum center): 2.26 m: Belt: EP250 2-ply 3+1.5 mm Oversized conveyor belt Transmission: Motovario NMRV 90 R7.5-1 90B14 Electric motor: Hansler 1.5 kW 4-pole B14 IE3 Belt width: 450 mm Band length (drum center): 2.26 m Band: EP250 2-layer C15 Chevron 3+1.5mm Drum diameter: 1.0 m. Length: 2.0 m Gearbox: Motovario H042 R10-1 90B5 Electric motor: Hansler 2.2kW 5-pole B5 IE3 motor Variable speed drive

Condition: ready for operation (used), Cone Crusher Svedala Hjdpfxspn I H Ts Agzsg Brand: Svedala Type: 36/H/MC Incl.: basic chasis and oil unit

Year of construction: 1982, condition: good (used), machine/vehicle number: 14320, Vertical Baling Press Hsdpfx Ageiuky Ijzjg

Year of construction: 1986, condition: good (used), machine/vehicle number: 2057, Hosokawa Alpine ZPS 315 classifier mill Universally applicable for materials up to a Mohs hardness of approx. 3.5 with requirements for very high final fineness with the lowest possible energy input. Classifier mill for high finenesses, cool grinding and flexible production parameters in the fineness range from less than 5 µm to 200 µm Hsdpfx Ajqi Hhpegzjg Impact beater mill with Turboplex classifier integrated in the upper section for precise particle size limitation Welded construction, grinding tools made of special steel The mill is available complete with accessories, such as: suction filter, rotary valves, cyclone, filter, fan, piping, control cabinet

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Hodpfjvwlqqsx Agzsg

Condition: ready for operation (used), Year of construction: 1989, Used single-toggle jaw crusher 1300 x 900 mm, including spare shaft and FAG 23152 K MB C3 bearings. Year of manufacture and make are unknown. The crusher operated reliably until 2023 and was then replaced with a mobile plant. Hsdpowmgw Njfx Agzog

Condition: good (used), Year of construction: 2002, operating hours: 11,245 h, machine/vehicle number: CCC00513, 239 kW weight: 50,5 t engine complete overhauled tracks as new new cylinder-sealing Hsdelhqhmepfx Agzog

Condition: not inspected (used), Hydraulic press for pressing paper etc. materials. The device was operational before disassembly. Press dimensions: length 4850 mm, width 1370 mm, height 3000 mm (possibility of reduction 2300 mm). Weight 3500 - 4000 kg. Hjdpfx Ajh Nyfysgzjg If you have any questions, please contact us at 539 660 495.

Condition: used, functionality: fully functional, color: yellow, overall weight: 8,680 kg, Year of construction: 1990, Hazemag impact mill APS 1013, used condition, functional, year of manufacture: 1990 Hjdpfow Swg Rox Agzsg