SEMI AUTOMATIC PASTING MACHINE

MAGRAF KA-100

Condition: used, Year of construction: 2016, Year: 2016 Condition: refurbished - very good condition - new steel roller + heating - new pressure roller with Teflon treatment - new bearings on main rollers - refurbished extraction and separation rollers - new suction cups Njdpfxsxvbgne Akcjwf - new perforation and deflection wheel Configuration - automatic loading - suction loading head - automatic separation - unloader - Jogger Technical specifications: - maximum lamination speed - 20 m / min. - sheet loading - automatic - loading system - Heidelberg suction loader - loading table capacity - 54 cm - sheet overlap regulation - automatic PLC controlled - overlap accuracy - + / - 2 mm - separation of laminated sheets - automatic, by cycling rollers - paper thickness - 115 - 500 gsm - main roller pressure - pneumatic - external compressor - 150 l / min, 6-8 bar - min. sheet size (w x d) - 20x 30 cm - max. sheet size (w x d) - 53 x 74 cm - max. output - 1650 B2 / hour - roller heating time - 8 min - temperature control - 80 - 140°C -

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Nedpfx Aewp Rqfjkcswf Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Year of construction: 1998, condition: like new (used), 65 Watt YAG laser Nedpfsd Dhw Nox Akcswf

Year of construction: 2026, condition: new, functionality: fully functional, Complete plastics recycling line for films and fibre materials from Taiwan leading Plastics Recycling Machinery manufacturer. GENIUS Machinery Co who have more than 30 years of recycling extruder production and experience. Extruder can be fed without size reduction or shredding.. Materials in baled, loose or reel form can be fed. Line can be supplied complete with Belt conveyor, Cutter compactor, Main extruder, Filtration system, (variety of types to suit requirements), Hot pellet die-face cutting device, Centrifugal pellet dryer, Vibrating screener, Storage silo for pellets. Additional ancillary equipment can be supplied . A two stage " Cascade" version is also available for heavily printed films, or very dirty films requiring double filtration. Alternative sizes from 100 kgs per hr up to 1200 kgs per hr can be offered. Full sales and support and training is available in UK and Europe for these extremely modern and economic machines. Nwedpfowg R Rtjx Akcjf

Condition: new, Year of construction: 2025, Cardboard Core winder maschine for Toilet Tissue paper rolls Specifications • Carton web width 60 - 76 mm • Production speed 35 - 40 m / min Nwjdpeit N Rvefx Akcef • Core i. diameter 40 mm - 80mm • No. of plies 2 , 3, 4 plies. (more optional) • Cut off length 600-2900 mm Features • Operation with either hot or cold glue. • Exchangeable mandrels. (for different core size) • Crush cutting by two or three circular cutters with synchronized movement. • Variable speed – electronic. (three phase)

Condition: excellent (used), Year of construction: 2012, Ref:11057 . 2012 Autobond Mini 105 TPHS-FL B1, double sided, fully automatic thermal laminator. Equipped with; Heidelberg deep pile suction feeder with back separation 250mm (10) diameter highly polished chrome laminating rollers Laminating nip pressure up to 6 metric tonnes 2 x Twin Tool Temperature Controllers Sheets are laminated top and bottom in one pass Rubber counter-pressure roller becomes water heated Additional heated roller, quick-change inflatable air-shaft, and perforating mechanism for 2nd roll of film Film is mounted on a quick-change air shaft Trim slitter and perforating mechanism Pneumatic clutch ensures precise film tension Swiss made temperature control unit Sheeter - Integral bump roller separator with anti-curl bar Pallet delivery table Specification: Max sheet size: 106 x 106 cm (41.73” x 41.73”) Min sheet size: 28.5 cm x 32 cm (11.5” x 12.5”) 115 gsm (80 lb text) to 650 gsm (24 pt) Max speed: 60 m/min (200 ft/min) Nwedpox U A D Ujfx Akcjf B1 sheets up to 5,000 SPH.

Condition: new, Year of construction: 2025, Entry-level sheet fiber laser metal cutting machine Lower laser cutting cost and easy operation The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Nwjdpfxjhwrgts Akcof Applicable Material: metal Condition: New Laser Type: Fiber Laser Laser Power: 1000W, 1500W, 2000W, 3000W Cutting Area: 3000*1524mm Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Cutting Speed: 0-100m/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: excellent (used), Year of construction: 1988, functionality: limited functionality, machine/vehicle number: 25.05.004, total length: 9,500 mm, total width: 2,250 mm, total height: 2,300 mm, input voltage: 380 V, power: 50 kW (67.98 HP), overall weight: 21,000 kg, empty load weight: 18,000 kg, compressed air connection: 7 bar, Equipment: documentation/manual, Paper size: 730 x 1060 mm, printing area: 710 x 1040 mm Paper thickness: 0.05 mm – 0.5 mm Preset maximum speed (due to simulation of the throw-off time for high-speed presses) is 4,000 sheets per hour, but the machine can operate much faster for commercial jobs. Four-fold central impression cylinder that prints all 4 colors in one gripper closure. 1988 FAG Speedproof with operator console for ink duct and cylinder adjustments, enabling extremely accurate register printing. Attached is the original factory brochure. The machine has been fully dry ice cleaned, and the cylinders are in excellent condition. Offered strictly on an 'as is, where is' basis. Nwodpfsuf Sy Asx Akcsf Maximum width is 225 cm, maximum height is 230 cm; shipping in a High Cube container is possible. Price is absolutely fixed, based on the removal of easily separated parts which we could sell separately, such as the Mabeg feeder with vacuum belt delivery, and the four-fold Baldwin stainless steel unit—with each color having its own bath, a mixer, and adjustable temperature control, so all four baths can be set to different temperatures and alcohol concentrations. The machine was dry ice cleaned, and it was intended for prominent use in printing electronic paper. However, due to too many initial losses, the project was discontinued. The machine has been with us for 3 years and, due to its size, I want to sell it as quickly as possible. Hence this very low price. It is an excellent machine. If the machine needs to be set up for testing and sampling, this is possible at an additional cost of €10,000, of which €5,000 must be paid in advance as a deposit under agreed conditions. All relevant information can be found in the original FAG folder for the machine, available via this advertisement as a PDF. Technical Data - Printing size max.: 710 × 1040 mm (27.95 × 40.94 in.) - Paper size max.: 730 × 1060 mm (28.74 × 41.73 in.) - Paper size min.: 500 × 700 mm (19.68 × 27.56 in.) - Stock thickness: 0.05 – 0.5 mm (0.002 – 0.020 in.) - Plate size max.: 800 × 1080 mm (31.50 × 42.50 in.) - Plate thickness: 0.25 – 0.5 mm (0.010 – 0.020 in.) - Speed max.: 4,000 sheets/h - Floor space requirement (incl. access to feeder, delivery, and central control desk): 950 × 525 cm (374 × 206.69 in.) - Press height: 230 cm (90.55 in.) - Weight (including paper stacked in feeder and delivery): approx. 18,000 kg (approx. 39,690 lbs) - Total power requirements: approx. 50 kW - Compressed air supply: 6 – 7 bar

Condition: used, Year of construction: 2026, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 204065, Used machine CNC cutter/plotter Cutting area in X and Y: 3,500 x 2,100 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials Equipment of the used machine • 1 cutting bridge and 1 multifunctional tool head The machine is sold with one driven circular knife, electric oscillating knife and one Milling Head + exhaust • Multifunctional tool head to hold max. 2 interchangeable tools • powerful vacuum blower for fixing the material • Standard equipped with gray conveyor table (Conveyor). Green-blue exchange conveyor possible (offers high contrast for dark materials) Can be extended with other tools (on request): • EOT electric oscillating blade • POT pneumatic oscillating knife • PRT rotating blade Nwedjif Ek Ropfx Akcof • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) (Product photo as example) The machine is CE certified.

Condition: good (used), Size max 750 x 1.050 mm Stroke height 940 mm Nedpfjd Hp H Iox Akcswf Lifting capacity max 600 kg