Used Automatic Creaser for sale (23,250)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding. Chsdozuzw Djpfx Afxeb

Condition: used, Year of construction: 2021, - Working width 1,350 mm - Belt feed speed 2 to 16 m/min - PRO SAND electronic control Automatically Calibrating Sanding Machine Manufacturer: SCM Type: DMC system Year of manufacture: 2021 Technical data - Working width 1,350 mm - Belt feed speed 2 to 16 m/min - PRO SAND electronic control - PLC terminal with 10.4" LCD color display Unit 1 TIE 5000 working unit for additional table, internal cross-padding - Sequencing system of the unit for belt change by only one machine operator - Automatic brake - Linear blower with timed activation for belt cleaning - Belt dimensions: 150 x 5,000 mm - Chevron belt dimensions: 140 x 4,710 mm PE16T EPICS electronic sector sanding, pitch 16 mm - 16 mm distance between sectors from center to center - Double-acting pneumatic cylinders with adjustable feed/counter feed - Graphite cloth with quick extraction device - Complete management of functions via the electronic Pro Sand control - Motor with inverter power up to 15 kW Unit 2 DO19 orbital unit for 19 rotating disc brushes - Manual adjustment of the unit's working position - 1.1 kW main motor with inverter drive - Independent motor for controlling the orbital movement - Diameter of the rotating disc: 125 mm FT/19/125 Set with 19 rotating discs, diameter 125 mm Unit 3 BF300 working unit for brush roller, diameter 300 mm - Manual adjustment of the roller's working position - 4 kW main motor with inverter drive FT 300 brush roller, diameter 300 mm Unit 4 BF300 working unit for brush roller, diameter 300 mm - Manual adjustment of the roller's working position - 4 kW main motor with inverter drive FT 300 brush roller, diameter 300 mm Unit 5 SC 2620 working unit for super finish pad - Rotation of the belt in the opposite direction of the conveyor belt - Electronic belt swiveling control - Disc brake - Chevron belt dimensions: 1,370 x 2,186 mm - Belt dimensions: 1,370 x 2,620 mm PE16/C EPICS electronic sanding block with sector pitch 16 mm - 16 mm distance between sectors from center to center - Double-acting pneumatic cylinders with adjustable feed/counter feed - Graphite cloth with quick extraction device - Complete management of functions via the electronic Pro Sand control - Inverter motor with a power of up to 15 kW Inverter-controlled vacuum motor integrated into the machine frame, up to 7.5 kW - Rubber-coated conveyor belt, 50 Shore - 4 kW conveyor belt motor with inverter drive Chsdpfxjzuzbco Afxjb Console with integrated PC eye-M and electronic Maestro Pro Sand control with tele service system Device connected to the machine that enables the use of the Maestro Pro Sand software. The integrated LED light strip enables the operator to monitor the machine's status in real time (emergency, operation, etc.) without having to be near the machine itself. It is equipped with a fanless industrial PC with protection class IP53 (IP65 on the front). This robust solution guarantees the highest level of resistance even under the most adverse environmental conditions that an industrial site can offer. The 21.5" LCD color display with a large 16/9 touchscreen enables particularly easy and efficient control of the machine's most important functions: - Full HD display resolution 1920x1080 - LED backlight - Capacitive

Condition: used, Year of construction: 2008, Automatic circular saw machine Manufacturer: Kasto Type: KASTOspeed C9 Year of manufacture: 2008 Technical data - For sawing steel and non-ferrous metals - Test machine, used very little. - Cutting direction 90°. - Saw blade diameter 250, 285 and 315 mm. - Cutting range approximately 15-90 mm or 15x15-80x80. - Power of drive motor for saw unit 11 kW (special equipment). This enables cutting speeds of 50-700 m/min, among other things. - 2 separate and independently selectable tanks for minimal lubrication. Accessories: - Angle magazine, loading length 6000 mm. - Material trolley with drawbar. - Portal crane, maximum load 1000 kg. - Oil mist extraction system. - Chip conveyor. - Chip tipping container with rollers. Note: Chodpfx Afozuymkjxob The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, machine/vehicle number: 007400, Max. panel width: 800 mm Max. panel length: 1250 mm No of injectors: 1 Positioning of Units by NC: yes Lateral horizontal groups: yes Chodpfx Afot Hmt Ioxob

Condition: used, Year of construction: 2020, Technical details: cutting diameter: 27 mm saw band length: 2910 mm saw band width: 0,9 mm span width: 320 mm dimensions of saw-band: 2910 x 27 x 0,9 mm band speed: 20 - 120 m/min electrical connection: 400/50/60 V / Hz. total power requirement: 1,5 kW machine weight approx.: 390 kg dimension machine approx.LxWxH: 1480 x 1700 x 2000 m Cjdpfxoy E Hyne Afxehb Fully hydraulic lowering and lifting function of the saw frame Hydraulic opening and closing of the vise Automatic shut-off after completion of cut, return of the saw arm to starting position Torsion-resistant saw frame made of cast steel (multiple ribbed) Hydraulic short-stroke cylinder for vise Precisely ground carbide saw blade guides, adjustable Electric coolant pump Manual band tension with display, including electrical monitoring of saw band and cutting pressure Hydraulic vise (opening and closing) Chip removal brush, running synchronously Large, solid round support table, rotates during miter cuts with predefined cutting channel; miter adjustment manual, readable via scale Material stop 500 mm with scale Incl. saw blade with combi toothing 4/6 Roller conveyor sections: 2 pieces of 3 m and 1 piece of 2.55 m. *

Condition: used, Technical details: cutting diameter: 260 mm saw band length: 4310 mm saw band width: 27 mm cutting range 90 degrees: round: 260 mm cutting range 90 degrees: square: 400 mm band speed: 17 - 110 m/min electrical connection: 400/50 V / Hz. total power requirement: 4 kW machine weight approx.: 1,22 kg dimension machine approx.LxWxH: 2,4 x 1,0 x 2,0 m dimensions L x W x H: 3,0 x 0,4 x 0,8 m Codpoy Dc N Ajfx Afxohb SBA 260/400 U = Fully Automatic Version ·Fully automatic sawing operation ·Automatic shutdown after completion of the cut ·Various accessories included (saw blades) ·Roller conveyor included *

Condition: refurbished (used), Year of construction: 2026, - The Trepko XPG 40 is a high-performance butter packing machine designed for automated packing of butter into various sizes. Known for its robust construction and outstanding reliability, this machine features advanced technology to ensure precise filling and wrapping. - Key attributes include: - Versatility: Suitable for different butter formats and packaging styles. - Efficiency: High-speed operation reduces production time while maintaining top quality. - User-Friendly controls: Easy to operate, allowing for quick adjustments and setup. - Hygienic Design: Constructed with easy-to-clean materials, adhering to food safety standards. - Durability: Built to withstand the demands of a busy production environment. - The Trepko XPG 40 is a trusted solution for manufacturers looking to enhance their butter packaging processes, ensuring both efficiency and quality. Format: 100 x75 x 30 mm Chsdpfx Afszwli Aexjb Butter Infeed: Twin Screw Augers Packaging Material: Foil, Parchment Paper, Grease Proof Capacity: up to 90 packs/min Weight: 1600 kg Power: 2.2 kW Available: Immediately Condition Details: Fully overhauled and ready to be used Not used since renovation

Condition: used, saw blade diameter 370 mm capacity 90 degrees: round 120 mm capacity 90 degrees: square 100 mm 180 x 100 mm Working height 925 mm saw blade turning speeds 17 - 70 U/min total power requirement 3,0 kW dimensions of the machine ca. 1,8 x 1,1 x 2,0 m Automatic cold circular saw Chodjzlkvdopfx Afxeb - CNC control - Micro-lubrication system

Condition: new, functionality: fully functional, machine/vehicle number: WV1ZZZSYS9072213, mileage: 10 km, power: 130 kW (176.75 HP), fuel type: diesel, overall weight: 3,500 kg, fuel: diesel, color: red, gearing type: automatic, number of seats: 8, Equipment: ABS, Android Auto, Apple CarPlay, air conditioning, airbag, cruise control, electronic stability program (ESP), full service history, lane keeping assist, navigation system, non-smoking vehicle, parking heater, power assisted steering, tire pressure monitoring, traction control, Vehicle conversion to an MTW (multi-purpose vehicle): Aluminum multi-purpose floor with aluminum checkered plate 6 individual seats in the passenger compartment Front warning lights LED Digital radio antenna for Tetra/GPS Adjustable radio loudspeaker Paint finish: bumpers and side protection strips in white Warning bar LED 1600mm with 17-button control panel in the superstructure console, gooseneck microphone Reading light on the passenger side Central electrical system including ambient lighting left, right and rear 2 storage boxes under the seats including securing straps MTW cladding with checkered plate up to window height and including wheel arches Center console between driver and passenger LEAB PowerAirBox B (230V) including 4m charging cable, automatic ejection and charger Sliding partition grille in the cargo area Folding table between the seat rows 2x 230V sockets outside 2x USB A and USB C in the center RWS reversing warning system Tie-down rails for securing cargo Step including removable center section at the rear and more Optional equipment: 2nd battery with battery monitoring Trailer coupling: fixed ball head Trailer stabilization program Audio-navigation system Discover Media (touchscreen, color display) Optional infotainment system with touchscreen color display 26 cm (10.4"), navigation system Equipment package: combination preparation Vehicle without cargo area partition, child safety lock electrically operated, heated rear window with wiper, windows in the cargo/passenger compartment: - fixed, front left, window in the cargo/passenger compartment: - fixed, front right, window in the cargo/passenger compartment: - fixed, rear left, window in the cargo/passenger compartment: - fixed, rear right, entry handle on B-pillar, roof lining, additional heater, rear wing doors with glazing, interior mirror with anti-glare function Exterior mirrors electrically adjustable and heated Battery and generator reinforced Driving Assistance Package Basic Intelligent Speed Assist including speed limiter Driving Assistance System: High beam assist (Light Assist) Chassis: damping and stabilizers reinforced, front and rear Climatic air conditioning (cab) with 2nd evaporator Storage package, storage: DIN compartment in front under the headliner, interior lights in the cab: reading light in front, additional evaporator Chedpszynmcefx Afxjb Side marker lights Fog lights with integrated cornering light Smoker's package Rain sensor Rear view camera Hinges for rear doors with increased opening angle Heated windshield washer nozzles Headlights LED Daytime running lights LED Mud flaps front and rear Mud flaps front, mud flaps rear Seats in the cab: passenger seat comfort Seats in the cab: driver's seat comfort Auxiliary heater for continuous operation and fuel-powered auxiliary heating Sockets (12V connection) in the cab (4 pieces) Sockets (12V connection) in the cargo/passenger compartment (2 pieces) Tinted rear windows Preparation for all-round warning lights Additional heater and evaporator Additional heater

Year of construction: 2025, condition: used, functionality: unexamined, Complete Automatic Roll Forming Line (fully compatible with all Unistrut products) Year of manufacture: 2025 Model: CIRF-2019-2486 Unistrut 41 x 41 and 41 x 21 profile Approximately 15 meters per minute Chodpozc Hkgjfx Afxeb UK / Irish wiring standard (UK wiring schematics, safety pull cord system around main beds) with 2-ton de-coiler 3-stage, 3-ram punching unit (Hole Size: Approx 12mm × 25mm / Hole Spacing: Approx 50mm centers) Fully automatic upstroke shear Auto Hydraulic Logo printer/stamper Discharge table Overall Length: Approximately 30 meters

Year of construction: 2008, condition: good (used), Anko BFK-10 Automatic stir fryer Capacity 60l, gas LPG, with a scraper and stirrer to scrape liquid eggs and stir fry ingredients, automatic temp control, variable speed, automatic tip discharge, suitable for cooking fried rice, fried noodle, dried meat cracker, dried meat floss, jerky, fried ground meat, ham, dried squid, steak, coffee, peanut, powder, bean, sugar coating, tea leaf, sesame, tofu, sticky rice and more, 3Ph Chodoh N Slxspfx Afxob

Condition: used, mileage: 947,741 km, power: 243 kW (330.39 HP), first registration: 01/2011, fuel type: diesel, number of seats: 54, gearing type: automatic, emission class: euro5, color: other, brakes: retarder, total length: 1,000 mm, total height: 3,300 mm, Year of construction: 2011, Equipment: ABS, cruise control, = Additional Options and Accessories = Csdpezxhmmsfx Afxshb - Webasto = Further Information = Damage: none = Company Information = We are an international company based in Belgium, located in the Brussels area (approx. 20 km). Belgian Bus Sales is your ideal partner for the purchase and sale of used buses and offers a large premises serving as an exhibition area. We always have numerous buses of all brands, capacities, models, and price ranges in stock. We can find the right coach, school bus, or city bus for you, tailored to your needs and budget. All information is provided without guarantee. Errors, prior sale, and typographical mistakes excepted. Opening hours for viewing used buses: Mon.-Fri.: 08:30 - 12:00, 12:30 - 17:00. Mowimy po Polsku (Agata) We speak your language: Nederlands, Français, English, Español, Português, Italiano, Русский, Polski, and more.

Condition: good (used), Year of construction: 1991, operating hours: 49,637 h, functionality: fully functional, machine/vehicle number: 9666, ram adjustment: 64 mm, conveyor belt width: 203 mm, pressing force: 50 t, control cabinet length: 940 mm, control cabinet width: 760 mm, stroke length: 1,651 mm, input voltage: 380 V, overall weight: 9,000 kg, control voltage: 24 V, sheet thickness steel (max.): 4 mm, input frequency: 50 Hz, sheet thickness aluminum (max.): 4 mm, Technical Data Codpozuur Uofx Afxshb Manufacturer: BRUDERER AG Model: BSTA 50 EL CNC Machine Type: CNC High-Performance Punching Machine Year of Construction: 1991 Machine Number: 9666 Press Force: 500 kN (50 t) Connected Load: 40 kW Main Motor Power: 25 kW Supply Voltage: 380 V / 50 Hz Control Voltage: 24 V DC Compressed Air Connection: 6–10 bar Operating Hours: approx. 49,637 h Adjustable Stroke: 16–51 mm Mounting Space/Clamping Plate: 760 x 940 mm Main Drive: 22 kW Power Supply: 400 V / 50 Hz Table Area: 940 x 580 mm Strip Feed Height (adjustable): 50–140 mm Max. Strip Width: 203 mm Max. Material Thickness: 4 mm Dimensions of machine with BBV 202: 2390 x 1270 x 3090 mm Machine Weight: approx. 9000 kg Configuration 2 x BRUDERER BBV 202/120 DOUBLE strip feeder KOHLER leveling machine 100.180/2.500.2M, year of construction 1992 Unwinding reel / coil reel Soundproof cabin Conveyor belt for part removal Lifting and sorting device for containers Roller conveyors and stacking racks Technical documentation available Description Complete BRUDERER high-performance punching line consisting of a precision punching machine BSTA 50 EL, BRUDERER strip feeder BBV 202/120, KOHLER leveling machine, unwinding reel, soundproof cabin, and discharge and conveying equipment. The system is designed for the efficient processing of strip material in high-speed punching operations. Extensive technical documentation is available.

Condition: used, Automatic lathe Codpjyllr Ijfx Afxohb Manufacturer: STROHM Model: M125

Condition: used, Riveting machine, double riveting unit with rotary indexing table, DUNKES Type DN 4 Rotary table, rotary indexing table with SIEMENS control Machine No. P 81 - 5458, Year of manufacture 1982 / 2009 Clamping force 40 kN Rivet shank diameter max. 12 mm Tool shank diameter 16 mm Overhang 190 mm Rivet head stroke per riveting unit approx. 60 mm Rivet spindle speed approx. 1400 rpm Installation height, tool - counter-tool max. 80 mm Compressed air requirement 6 bar Motor power per riveting unit 1.1 kW Mains connection 380 Volt, 50 Hz - Rotary table, indexing table with servo drive, step size programmable via Siemens PLC control - Double riveting unit is adjustable within the machine frame in relation to the rotary table - Table size Ø 295 mm for holding round workpieces - Pneumatic riveting stroke movement - Riveting unit adjustment via geared motor with lead screw, positioning via adjustable microswitch - Modernization of the control system and conversion of the servo drive in the rotary table in 2009 - New electrical control cabinet with Siemens Simatic Panel - Year of manufacture 2009 - Riveting time continuously programmable Chodpfx Ajdzp T Njfxob - Riveting pressure adjustment continuously adjustable via pressure gauge - Micrometer stop for limiting the stroke of the counter-rotating riveting units, 0-60 mm Space requirement L x W x H 3200 x 1250 x 2400 mm Weight approx. 2500 kg Good condition The machine was used for riveting segment saw blades from Ø 400 to Ø 2000 mm. The segments were manually placed on the support disc and fixed with straight rivet pins. The counter-rotating riveting unit rivets the pin simultaneously from both sides. The controlled table automatically rotates to the next working position. Ideal for saw blade manufacturers and repair companies. Or for the construction of a special machine. The riveting unit can also be easily removed and used as a conventional riveting machine by creating a suitable counter-tool.

Condition: ready for operation (used), Year of construction: 2014, operating hours: 1,618 h, travel distance Z-axis: 430 mm, number of axes: 5, number of slots in tool magazine: 16, table length: 4,300 mm, table width: 2,205 mm, spindle motor power: 13,000 W, spindle speed (max.): 20,000 rpm, swivel angle B-axis (min.): -99 °, swivel angle B-axis (max.): 100 °, swivel angle C-axis (max.): 360 °, This 5-axis BIESSE Rover A FT 2243 including WINSTORE 3D K1 was manufactured in 2014. It operates on a 400 V power supply. With approximately 1,700 hours of axis movement, this CNC wood machining centre is designed for precision and efficiency. If you are looking to get high-quality wood machining capabilities, consider the BIESSE Rover A FT 2243 machine we have for sale. Contact us for further details. Technical Data • Working Table Dimensions: 4,300 × 2,205 mm • Maximum X-Axis Speed: 80 m/min • Maximum Y-Axis Speed: 60 m/min • Maximum Z-Axis Speed: 20 m/min • Z-Axis Travel (3-/4-Axis Version): 325 mm • Z-Axis Travel (5-Axis Version): 430 mm • Maximum Workpiece Clearance in Z: 170 mm • Maximum Workpiece Clearance with Sweeping Arm: 120 mm • X-/Y-Axis Drive: Rack and Pinion • Z-Axis Drive: Ball Screw Chodpfx Afjzuygqjxsb • Axis Guides: Linear Guides with Recirculating Ball Bearing Blocks • Vacuum Pump Capacity: 300 m³/h at 50 Hz • Vacuum System: 20 Independent CNC-Controlled Zones • Working Fields: 2 • Clamping Areas: 2 in X • Pneumatic Stops: 16 • Grid Table Pitch: 30 mm • Vacuum Module Dimensions: 132 × 146 mm • Vacuum Module Height: 29 mm • Vacuum Module Rotation Increment: 15° • Air Cushion Table Blower: Yes • Maximum Single Panel Thickness: 50 mm • Minimum Single Panel Thickness: 9 mm • Maximum Multiple-Panel Loading Thickness: 20 mm • Maximum Multiple-Panel Unloading Thickness: 60 mm • Protective Board Thickness: 8–25 mm • Maximum Panel Weight: 200 kg • Minimum Loadable Panel Size in Y: 800 mm • Unloading Conveyor Length: 4,800 mm • Maximum Unloadable Panel Length: 4,300 mm 5-Axis Machining Unit • Number of Axes: 5 Interpolating Axes • Tool Interface: HSK F63 • Cooling: Liquid-Cooled • Power S1: 11 kW / 15 HP at 12,000 rpm • Power S6: 13 kW / 17.4 HP at 12,000 rpm • Maximum Spindle Speed: 20,000 rpm • C-Axis Rotation: 360° Continuous • C-Axis Speed: 12.4 rpm • B-Axis Positioning Range: ±100° • B-Axis Speed: 12.4 rpm • Spindle Bearings: Ceramic • Drive Motor: Brushless, Digitally Controlled • Gearbox: Harmonic Reduction Gear • Lubrication: Lifetime Lubrication Drilling Head • Type: BH 26 2L • Maximum Number of Tools: 26 • Vertical Drilling Spindles: 16 • Vertical Spindle Arrangement: 8 in X / 8 in Y • Vertical Spindle Pitch: 32 mm • Horizontal Drilling Spindles: 4 with Double Output • Horizontal Spindle Axis Distance: 32 mm • Grooving Saws: 2 • Grooving Saw Directions: X / Y • Grooving Saw Diameter: 120 mm • Maximum Grooving Depth: 25 mm • Motor Power: 1.7 kW at 2,800 rpm / 3 kW at 6,000 rpm • Maximum Drilling Speed: 6,000 rpm Tool Magazine • Type: Turret Tool Magazine • Capacity: 16 Tools • Tool Position Spacing: 114 mm • Maximum Tool Diameter with Full Magazine: 110 mm • Maximum Individual Tool Weight: 7.5 kg • Maximum Total Tool Weight: 55 kg Automatic Loading / Unloading • Loading Direction: Front • Material Flow: Right to Left • Loading / Unloading System: Type B • Suction Cups: 5 • Automatic Loading Capacity: Up to 3 Panels • Sweeping Arm: Yes • Automatic Table Cleaning: Yes • Loading Table: Automatic X/Y Alignment • Unloading Conveyor: Motorized • Conveyor Control: CNC-Controlled • Conveyor End Detection: Photocell WINSTORE 3D • System: WINSTORE 3D K1 • System Length: 16,000 mm • Beam Length: 8,000 mm • Additional Modules: 3,000 / 6,000 / 8,000 mm • Maximum Suction Frame Length: 5,200 mm • Cross Conveyors: Belt Type, 5,200 mm • Panel Handling: Raw and Thin Panels • Panel Weight Detection: Load Cell

Condition: used, Year of construction: 2004, Technical details: Basket size LxWxH: 530 x 320 x 200 mm Max. basket weight: 50 kg capacity: 4 Körbe/h; baskets/h No. of washing chambers: 1 No. Of tanks for washing: 1 No. Of tnks for conserving: 1 Cleaning medium: Tetrachlorethen Electrical heating power: 42 kW Csdpfx Aezu St Nefxjhb Machine size LxWxH: 4 x 3 x 2 m

Year of construction: 2016, condition: good (used), for sale: Complete Niverplast packaging line Year of manufacture: 2016 1. Manual infeed Niverplast 2. Depanner for baguettes from AUXPAMA 3. Metal detector 4. Reject system 5. Counter + speedbatcher Niverplast 6. Combiplast Niverplast 7. Boxloader Niverplast 8. Varioseal Niverplast 9. Metal detector 10. Pallet sealing device 11. Conveyor systems Niverplast Full documentation, layout, and specifications available. If you have any questions or comments, please feel free to contact me. Inspection on site is also possible. Dismantling and transport can be offered. Chodpfxjx Ari Hs Afxsb Kind regards, Leo Holland

Condition: used, Füller 4 Ventile motor für Vakuum Chsdszx Drxopfx Afxeb Edelstahlausführung

Condition: used, Year of construction: 2014, Candle Filter System – Automatic, 3 Filters Chedezx Dhmepfx Afxob 2x Filter housings 30" x 3 FBFM33 1x Candle filter FBT013GNW25J 1x Sepex pump 1x Pump for injection of oenological product after filtration or reinjection of wine 1x Mounted on skid, fully equipped with fixed piping

Condition: used, - Demonstration machine - Frame and work table made of stainless steel - Liquid circuit for continuous use up to 90⁰C - Filling head fully closed by security glasses, - Automated cycle start, automated tap removal, automated capping - Multifunctional coloured display, with touchscreen - Supply voltage: AC220V/50Hz±10% - complies with the Machinery Directive 2006/42/EC Video:  ?v=BDoyMhHtzIg [1] *Capacity depends on bag type* 3 l bag – approx. 400/420 per hour 5 l bag – approx. 345/370 per hour 10 l bag – approx. 260/295 per hour 15 l bag – approx. 210/245 per hour Chsdezx Dacspfx Afxjb 20 l bag – approx. 175/210 per hour [1] ?v=BDoyMhHtzIg

Condition: used, machine/vehicle number: SH01-332, motor defect. 5000 EUR afte repair Cjdozx A Skjpfx Afxehb

Condition: used, Year of construction: 2019, Semi- automatic labelling machine model S1/M – CONSOLE 230V, 50 Hz, Single phase Max approx 700 bph Console for labelling adjustment Cjdpfxezx Av Nj Afxjhb Paper web passage height H=150mm

Condition: used, Die halbautomatische Verschlussmaschine RLC1 ist für die Verpackung von Glasflaschen mit 26 oder 29mm Kronkorken geeignet. Die Schließeinheit kann auf Kronkorken von 26 oder 29mm Durchmesser verwendet werden. Wenn man beide Durchmesser braucht, wird eine zusätzliche Schließeinheit geliefert. Der Schließkopf der Kronkorken ist aus gehärtetem Stahl, und auch im Laufe der Zeit ist er verschleißfest. Die Schiene führt die Kronkorken in der richtign Position. Die spezifische Form der Schiene wird spezifisch für die Kronkorken aus Edelstahl 304 gebaut. Diese enthält eine kleine Menge Kronkorken, die manuell eingegeben werden können. Die Schließeinheit zieht die Kronkorken aus der Schiene heraus und steckt sie in den Schließkegel. Auf Anfrage kann man einen Trichter einbauen, um eine größere Menge Kronkorken einzugeben. Den EG-Normen entsprechend startet der Verschlussprozess mit dem gleichzeitigen Drücken von zwei Tasten. Nach der Positionierung der Flasche auf den Halter, fängt der Verschlussprozess an, die Schließeinheit sinkt auf die Flasche und verschliesst der Kronkorken, automatisch kehrt die Schließeinheit zurück. Maße: L 0,41m H 1,96 m B 0,41 m Csdpfxozx Au So Afxshb Gewicht ca. 80kg Gewicht mit dem automatischen Trichter:140kg Max Durchmesser der Flasche 220 ​​mm nutzbare Höhe max 500 mm

Condition: used, Year of construction: 2012, operating hours: 31,800 h, functionality: fully functional, CNC long-turn lathe Manufacturer: STAR Type: SR-32J Codpfxszu I Ago Afxshb Year of manufacture: 2012 with: FANUC 32i control system Back-end machining Synchronous spindle Powered tools C-axis Chip conveyor Parts conveyor belt Oil mist extraction system Fire extinguishing system Bar loader magazine FMB TURBO 3-36