Cnc roll grinder buy used

Identified location: Ashburn (US) (Edit)
Enter your address
or
Move
13

Tool and Cutter Grinder ROLLOMATIC CNC 48 F4

Brügg, SwitzerlandSwitzerland dealership location
6614 km
ready for operation (used)
Technical data Grinding diameter 1.0-12.7 mm Grinding length 0-75 mm Helix angle 0-89 G9noncits ° Tool length 30-200 mm ... more
17

Tool and Cutter Grinder ROLLOMATIC CNC 48 F4

Brügg, SwitzerlandSwitzerland dealership location
6614 km
ready for operation (used)
Technical data Grinding diameter 1.0-12.7 mm Grinding length 0-75 mm Helix angle 0-89 ° Tool length 30-200 mm ... more
1
Elect./Voltage: 460 V, 60 Cy, 3 Ph. Nfho2 THERMWOOD C 53 5 X 10 with roller hold down and off load:5' x 10' Fixed table, moving gantry in a front-to-back configuration with a structural composite table fly-cut to provide a precision work surface, roller-hold down for stack cutting and securing parts without vacuum; included is an auto-load system, and an auto-adjust 5' X 10' off-load scissors lift. -- Equipped with:(1) 10 HP THERMWOOD Extended duty motors, fixed speed at 15,000 RPM, and (1) ... more
6
**SPECIAL OFFER: FREE OPERATOR TRAINING COURSE IF MACHINE SOLD IN FEBRUARY** ***MACHINE AVAILABLE TO END USER CUSTOMER ONLY*** S20 CNC FAVORIT, 400mm CENTRES X 100mm, MARPOSS LENGTH POSTIONING UNIT, TABLE SWIVEL 15 DEGREES, SWIVELLING WORKHEAD, TAILSTOCK WITH FINE TAPER ADJUSTMENT, SENSITRON AIR GAP ELIMINATOR, FANUC 16 T WITH PICTOGRAM PROGRAMMING, VERY WELL MAINTAINED..... Fwzm8un WE BUY/SELL ONLY SELECTED STUDER MACHINES DIRECT TO/FROM CUSTOMER. WE ARE SPECIALIST ONLY IN STUDER MA... more
6
Maximum swing over bed 530 mm. Spindle speed 2 steps. Bcrbmggqzd 10 - 564 Rpm /564 - 2000 Rpm. Centerheight 260 mm. Maximum turning length 3000 mm. CNC Control Fagor 8055 more
6
grinding diameter 1800 mm grinding length 10000 mm swing diameter 2000 mm grinding diameter - min. 80 mm grinding length min. 800 mm workpiece weight 50 t grinding spindle speed 5 - 1400 U/min roll drive 0 - 150 U/min feed speeds Z = 10 m/min feed speeds X = 5 m/min feed speeds Q1 = 2 m/min feed speeds Q2 = 2 m/min travel -z axis 11020 mm travel -x axis 850 mm U-axis -4,91 / + 4,95 = 9,86 mm roll drive 51 kW grinding wheel motor 22 kW total power requirement ca. 100 kW weight of the machine ca.... more
6

CNC cycle controlled heavy duty lathe Fremtas/Stanko/Ryazan DR100F3 x 5000

Overath, GermanyGermany dealership location
6430 km
2018
as good as new (ex-display)
incl. overhaul / modernising CNC control Fagor or Siemens delivery time approx 4-5 month Including normal equipment: - electrical equipment 24/230/400V german fabrication (CE-Norm) - machine lamp 24Volt - cooling unit - steel holder, 4-fold, incl. upper support - 4-chuck faceplate 1000mm - Savety housing - central lubrication SKF/Vogel -1 set technical documentation, including: -- Operating manual -- circuit diagramm -- programming manual -- decleration of conformity (CE) - m... more
6
Cycle controlled CNC lathe of GEMINIS type CNC 1200 Masch. No. 4991 HV 480 F year 1985 CNC control FAGOR 8020T Top width 2000 mm Tip height over bed 545 mm Top support above 270 mm Plan route 860 mm Bed width 800 mm Quill recording about MK 6 short mount Spindle bore 105 mm Spindle head size Cammlock size 15 Spindle speed range 1. transmission level 2.8-90 RPM = 12500 NM 2. transmission level 3.5-180 RPM. = 6250 NM 3. transmission level 3.5-355 RPM = 3125 NM 4. transmis... more
1
Elect./Voltage: 440 V, 60 Cy, 3 Ph. Ncdm9 [...] ONSRUD S-Series 98S18R CNC Router with ATC and Roller Hold-Down:"S" Series Moving table CNC Router with: 49" x 98" table in a front-to-back configuration and axis travel of 98" x 74". Phenolic surface, machined universal grid vacuum table single vacuum zone with (3) pop-up positioning pins . -- Thermal heat treated:Stress relieved & normalized steel frame base & moving gantry bridge, vertical supports & Dual Drive 1,400 IPM machining speed with... more
8
***MACHINE AVAILABLE TO END USER CUSTOMER ONLY*** WE SELL-RENT-BUY-OPERATOR TRAINING-GEOMETRY CHECKS-SERVICE ONLY STUDER MACHINES WITH 40 YEARS STUDER EXPERIENCE. 650MM CENTRE DISTANCE x 175MM HEIGHT, EXTERNAL WHEEL 500MM, ACTIVE LENGTH POSITIONING, MOVOMATIC IN PROCESS GAUGE READY, ELECTRONIC WHEEL BALANCING, SWIVEL OF TABLE 8.5 DEGREES, COOLANT TANK, TAILSTOCK WITH FINE TAPER ADJUSTMENT, SENSITRON AIR GAP ELIMINATOR, FANUC 21i T, GRANITAN BASE GRINDING MACHINES FOR RENT..... *****GRAN... more


cnc roll g...
daily

New machines via email!

Stay updated!
11

Cycle controlled CNC lathe Gildemeister NEF 500 Plus

Welserstr. 10 E, 51149 Köln, DEGermany
6422 km
1998
unexamined (used)
1 used cycle-controlled lathe Manufacturer: Gildemeister Type: NEF 500 plus 1998. Control: HEIDENHAIN MANUAL PLUS 3110 Swing over bed 500 mm Top width 1000 mm Spindle bore 70 mm Nunlhai Speeds 3 levels of 8-2800 RPM. Spindle mount Mt 5 11 kW Weight approx. 3 t more
3

Tool and Cutter Grinder SCHÜTTE WU63-CNC

Mülheim.an der Ruhr, GermanyGermany dealership location
6388 km
used
max. grinding diameter 260 mm grinding length 610 mm workpiece length 680 mm y-axis 230 mm z-axis 280 mm centre height 115 mm swing dia. 260 mm Bxuqcn7w total power requirement 1,3 kW weight of the machine ca. 1,4 t dimensions of the machine ca. 2,7 x 1,8x 1,8 m YOM in mid 1990, in 2010 completely modernized with new CNC control - speed of the workpiece (division) 1-100 rpm - number of divisions max. 999 - Feeds X axis 0.1 - 12,000 mm / min - Feeds Z axis 0.1 - 2000 mm / min - Solution in X... more
6

Roll Grinders MSO HEID RNC338

Remscheid, GermanyGermany dealership location
6419 km
1987
used
grinding diameter 750*100 mm grinding length 2000 mm swing diameter x mm centre height 240 mm table - swivable 5/15 Grad spindle turning speed range 2100 U/min max. workpiece weight between centres 400 kg grinding diameter - min. 30 mm Srokjo total power requirement 21 kW more
4
Description: Suitable for manufacturing and regrinding wood- and metalworking tools of all kinds. Specifications: Working range: longitudinal traverse (X-axis) 350 mm, vertical traverse (Y-axis) 200 mm, cross traverse (Z-axis) 470 mm, rotary table swivelling range (C-axis) +/- 200°, work head spindle ISO 50, centre height (with / without worktable) 130 / 160 mm, max. diameter of workpiece 100 mm, max length of workpiece 270 mm, max. dia. of wheel 150 mm, grinding spindle power 7 kW, connect... more
1

CNC CONTROLLED LATHE -MULTISPINDLE CALPE TH5-1600

North Carolina, United StatesUnited States dealership location
518 km
2001
used
Elect./Voltage: 575 V, 60 Cy, 3 Ph. Bbuqvtxzos CALPE TH5-1600 Heavy-Duty High-Production, Fully Automatic CNC Lathe: General Description: -- Multi-Spindle cutting simultaneously, (5) spindles using V-type gouge knives. -- 63" (1,600 mm) Max. distance between centers; 5-1/2" (140 mm) max. swing diameter between spindles. -- CNC Controlled with 3.35" (85 mm) travel for depth of cut. Motors/Speeds: -- (2) Head stock motors, each 12.5 HP - 1,750 RPM; -- CNC controlled electronic variable... more
7
"B" AXIS 1 DEGREE range -15/+225, 1000MM CENTRE DISTANCE x 175MM HEIGHT, 2 EXTERNAL WHEELS 500/400MM, INTERNAL GRINDING, ACTIVE LENGTH POSITIONING, SWIVEL OF TABLE 8.5 DEGREES, COOLANT TANK, TAILSTOCK WITH FINE TAPER ADJUSTMENT, SENSITRON AIR GAP ELIMINATOR, FANUC 16T. MACHINE AVAILABLE TO END USER CUSTOMER ONLY WITH OPTION OF INSTALLATION, OPERATOR TRAINING, SERVICE ETC GRINDING MACHINES FOR RENT..... WE BUY/SELL ONLY SELECTED STUDER MACHINES DIRECT TO/FROM CUSTOMER AND OFFER INSTALLATION... more
5

Cold Rolling Machine BAD DUEBEN PRZ 40 CNC AC

Metzingen, GermanyGermany dealership location
6677 km
1997
used
rolling capacity max. 40 t workpiece diameter 2-80 mm workpiece length 100 mm threading length 80 - 100 mm total power requirement 2 x 8 kW weight of the machine ca. 8,5 t dimensions of the machine ca. m Bgpcr83o0 CNC-Spline Rolling Machine with Workpiecehandling betw. Centers more
6

Tool and Cutter Grinder SCHÜTTE WU63-CNC

Mülheim.an der Ruhr, GermanyGermany dealership location
6388 km
used
max. grinding diameter 260 mm grinding length 610 mm Bcchcfltns workpiece length 680 mm y-axis 230 mm z-axis 280 mm centre height 115 mm swing dia. 260 mm total power requirement 1,3 kW weight of the machine ca. 1,4 t dimensions of the machine ca. 2,7 x 1,8x 1,8 m YOM in mid 1990, in 2010 completely modernized with new CNC control - speed of the workpiece (division) 1-100 rpm - number of divisions max. 999 - Feeds X axis 0.1 - 12,000 mm / min - Feeds Z axis 0.1 - 2000 mm / min - Solution in... more
12

Sheet metal roller Roundo Sweden PAS 340 CNC

Babberich, NetherlandsNetherlands dealership location
6320 km
ready for operation (used)
Technical data SteuerungsartRoundo wCNC2 Hdqebmd Hydraulic / MechanischHydraulic 3 or 4 Walzen4 roll Blechstärke35 mm Biegelänge1000 mm Maximum sheet thickness Ø 2.50035 mm Max on bending capacity Ø 2.50030 mm Top roller Ø340 mm ... more
6

Roll Grinders SCHMALTZ R68/2000

Willich, GermanyGermany dealership location
6368 km
1965
used
grinding diameter 680 mm grinding length 2000 mm G2kzdtdte swing diameter 800 mm coolant tank l total power requirement 35 kW weight of the machine ca. 10 t more
5

Roll Grinders SCHAUDT PF5N2000

Leipzig, GermanyGermany dealership location
6734 km
1992
used
grinding diameter: 460 mm grinding length: 2000 mm centre height: 250 mm Control: S 3G-4C Siemens grinding wheel hole diameter: Aufnahme Ø 304,8 mm swing diameter: 500 mm workpiece weight: [...]: 600 kg total power requirement: 53 kVA S8v8owu0n weight of the machine ca.: 8,5 t space requirements of the machine approx.: L:7,5xB:5,4xH:2,3 m applicable for manufacturing of rolls and conical grinding possible further details: grinding headstock: diameter speed 45m/s, travel x= 425, fixed grinding d... more
6
MACHINE AVAILABLE FOR RENT WITH OPTION TO PURCHASE COMPACT DESIGN (JUST OVER 2 METRES IN WIDTH), EASY PROGRAMMING WITHOUT ANY KNOWLEDGE IN GRINDING, MACHINE HAS STUDER ESTABLISHED GRINDING KNOW HOW IN MEMORY. 1000MM BETWEEN CENTRES 175MM CENTRE HEIGHT, 500MM WHEEL AT 44 METRES PER SECOND, AUTOMATIC "B" AXIS +/- 8.5 DEGREES, AUTOMATIC WHEEL BALANCING, HYDRAULIC TAILSTOCK, EXCEPTIONAL LIVE GRINDING ROUNDNESS BELOW 1 MICRON, MOVOMATIC READY, RENISHAW LENGTH POSITIONING, SERVICED BY STUDER TRAINED ... more
3

Tool and Cutter Grinder SCHÜTTE WU 750 CNC N6

Metzingen, GermanyGermany dealership location
6677 km
1992
used
max. grinding diameter 0 mm grinding length 0 mm workpiece length 970 mm H9hygypyo total power requirement 12 kW weight of the machine ca. 5 t dimensions of the machine ca. m more
4

Lathe - cycle-controlled MAS MT 50 CNC

Bühl, GermanyGermany dealership location
6593 km
1998
used
turning diameter 500 mm turning length 1450 mm control HEIDENHAIN MANUAL PLUS greates pass round over bed 500 mm swing diameter over slide rest 350 mm centre height 255 mm centre distance 1500 mm spindle bore 82 mm spindle turning speed range 2 - 2400 U/min spindle nose DIN 55027 max. torque on the spindle max. 1055 Nm face slide travel 260 mm 140 mm rapid travel - longitudinal/face 5 m/min tailstock quill diameter 80 mm tailstock quill stroke 180 mm tailstock taper MT 5 total power requirem... more
1

6-axis CNC tool and Cutter Grinder MAKINO SEIKI CNV 2-40

Bretzfeld-Schwabbach, GermanyGermany
6655 km
1994
ready for operation (used)
CNC FANUC 15 M, Doppelschleifspindel and loaders. Suitable for the forehead, Nutschleifen, sharpening and back loops of milling tools. maximum tool shank diameter 42 mm maximum tool length (for R-loops) 150 mm maximum radius of grinding 60 mm Max tool diameter 170 mm Max slope angle (left, right) 65 ° X 420 mm Y-axis 250 mm Zaxis 280 mm A-axis 360 ° W-axis - 120 to + 5 ° B-axis +/-90 ° (manual) C1-axis +/-180 ° (manual) Spindle stock tilt/spindle stock Cross movement fine adjustmen... more
6
New in: 1998 Retrofitted with Siemens 840D control in 2008, Lkmfh capacity 400 x 1200, 1 x Marposs E82 Balance, 1 x 1030 x 50mm grinding wheel Dimensions: Factory Footprint Width 7 metre x Depth 6 metre x Height 3 metre more
4
TECHNICAL SPECIFICATION Length of the saw blades 200 - 1000 mm Thickness of the saw blades 0.5 - 3.0 mm Tooth pitch 3 - 75 mm Bb03cewlfb Tooth depth max. 15 mm Viewing angle 0 ° - 25 ° Baking angle 0 ° - 20 ° Cycle time 100 - 1000 mm / min. Grinding wheel RPM 3800 rpm Grinding wheel diameter 200 mm Diameter of the shaft of the grinding wheel 32 mm Width of the grinding wheel 3 - 6 mm Compressed air - min. 6 bar Compressed air volume cca 2 m3 / h Engine specifications: Spindle... more
12
AVAILABLE TO END USER CUSTOMER ONLY WITH OPTION OF FULL STUDER SERVICE-INSTALLATION-STUDER CNC TRAINING- GEOMETRY CHECK, available for RENT-SALE-OR RETROFITTED WITH NEW SIEMENS CNC by STUDER TRAINED ENGINEER WITH MANY YEARS EXPERIENCE IN FIELD ON STUDER CNC GROSSENBACHER, SIEMENS, MOVOMATIC IPG, RENISHAW LP2 ON THIS MACHINE Bcnrfj9fms more
3

Tool Grinder - Universal SCHÜTTE WU 500 CNC - 4

Metzingen, GermanyGermany dealership location
6677 km
1989
used
max. grinding diameter 320 mm grinding length 500 mm workpiece length 700 mm total power requirement 10 kW weight of the machine ca. 4 t dimensions of the machine ca. m Height of centres220mm Distance between centres / clamping length750 / 500mm Table size290 x 1,600mm Intermediate table110 x 1,200mm X / Y / Z axes500 / 320 / 320mm Feed speeds, X, Y & Z axes0.005 - 5m/min D2eo3rf Grinding head swivelling, vertical axis, manual200° Grinding head tilting, manual+/- 90° Speed range of R axi... more
4
Bcsu3imyn7 cylindirical grinder with CNC SIEMENS SINUMERIK 840 and MARPOSS In-Process Measuring Control ; All sales are subject to the seller's consent. Delivery date: about 3-4 days. At location/Fundament. more
5
Cycle-controlled CNC lathe Fabr. HARRISON type Alpha 400 Gkb2pdfl0 Masch.# A30154 built in 1996 Technical data: Tip height 195 mm Top width 1250 mm Swing over bed 400 mm Swing over facing slide 246 mm Swing in the offset 585 mm The offset width 165 mm Spindle bore 54 mm 3 infinitely variable spindle speeds of 15-275, 35-795, 110-2500 RPM. Bed width 318 mm Feed x up to 3000 mm / min. Feed Y up to 1500 mm / min. 12 metr. Feeds 0.03 - 0.4 mm / Rev. 12 inch feeds 0.001 - 0.016 "/ U... more
3
 Start Chat

CNC Surface grinder JUNG JC 500 CNC-E

ČeskoCzech Republic
7010 km
1995
good (used)
Control system: SINUMERIK 805 Ptppoa Travel distances: X: 600 mm Y: 230 mm Z: 400 mm Machine weight: 2700 kg Accessories: Magnetic clamping table more
6

Roll Grinders HERKULES UWS 450

Düsseldorf, GermanyGermany dealership location
6394 km
used
grinding diameter 950 mm grinding length 6500 mm Ccch2wrg swing diameter 1000 mm workpiece weight 18 t grinding wheel peripheral speeds: 36 m/s longitudinal feeds, infinitely variable 200 - 2800 mm/min grinding wheel speeds 415 - 830 U/min grinding wheel size 750 x 70 x 305 mm grinding motor 20 kW workpiece turning speeds 6,7 - 60 U/min creep feed 20 mm/min total power requirement 65 kW weight of the machine ca. 45 t dimensions of the machine ca. 13 x 4,5 x 2,1 m 1986 retrofit with stepless ... more
9
STUDER S35 retrofitted with NEW SIEMENS CNC in 2017 eliminating the original Grossenbacher cnc CAN PROFILE WHEELSHAPES-MARPOSS AIR GAP CONTROL, AUTOMATIC WHEELHEAD SWIVEL FOR ANGLE GRINDING-LENGTH POSITIONING AT AN ANGLE (WITHOUT NEED TO STRAIGHTEN UP), EASY GLIDE DOOR, RIGHT SIDE START CYCLE-DRESS-ABORT CYCLE BUTTONS,....machines originally built from 1989 to 1993 *****MACHINE AVAILABLE TO END USER CUSTOMER ONLY***** WE SELL-RENT-BUY-OPERATOR TRAINING-GEOMETRY CHECKS-SERVICE ONLY STUD... more
3

Tool Grinder - Universal SCHÜTTE WU 500 CNC 6

Metzingen, GermanyGermany dealership location
6677 km
1989
used
max. grinding diameter 300 mm grinding length 500 mm workpiece length mm Number of axles 6 St. centre height 220 mm centre distance 500 mm x-axis 500 mm y-axis 320 mm z-axis 320 mm total power requirement 5 kW weight of the machine ca. t dimensions of the machine ca. m Height of centres200mm Distance between centres / clamping length750 / 500mm Table size290 x 1,600mm Intermediate table110 x 1,200mm X / Y / Z axes500 / 320 / 320mm Feed speeds, X, Y & Z axes0.005 - 5m/min Grinding head s... more
7
Bcsuzjbaft grinding dia 2 - 400 x 500 mm, MARPOSS In-Process Measuring, Wheel-Balancing System and Tool-Monitor, Gantry-Loader for Infeed-Grinding, Coolant+Bandfilter, weight 10 tons ; All sales are subject to the seller's consent. Delivery date: about 3-4 days. At location/Fundament. more
4
Description: Suitable to regrind and manufacture wood and metal working tools of all kinds. Specifications: X axis lateral movement 360 mm, Y Axis cross movement 250 mm, Z axis vertical movement 250 mm, C axis swing area 340° workpiece mount ISO 50, Max. grinding wheel diameter 200 mm, Grinding spindle rating 4 kW, Grinding spindle speed stepless 1000 - 9000 U / min., connected load 10kW (400 V / 50 Hz), dimensions W x D x H 1470 x 2450 x 2165 mm, weight approx. 2800 kg, colour Green / Grey... more
3

Roll Grinders CHURCHILL TWR

Willich, GermanyGermany dealership location
6368 km
used
grinding diameter 155-1825 mm grinding length 7350 mm swing diameter 750 mm workpiece weight 15000 kg total power requirement kW weight of the machine ca. t Dwb2nm dimensions of the machine ca. m more
14

CNC universal grinder Erwin Junker BUAJ 30

Králova 279/9, 61600 Brno, CZCzech Republic
7113 km
2000
good (used)
Repairs/replacements: 2013/10 carrier bearings 2014/7 headstock measuring 2014 drive motor of the grinding wheel replacement 2015/6 ball screw and spindle bearings Grinding diameter: 300 mm Grinding length: 630 mm Centre height: 150 mm Control: FANUC Mptkd Power capacity: 5,5 kW Grinding wheel diameter: 400 mm Workpiece weight: 120 kg Swivel angle for work spindle: +45/-15 ° Long. travel of table: 756 mm Total power requirement: 7,5 kVA Weight of the machine ca.: 2800 kg Dimensi... more
6
There are two machines available: ITM 2020-4 and ITM 2020-6: X-travel: 400mm, y-travel: 500mm, z-travel: 300mm, A-travel: 360°, U-travel: 180°, power: 28kW, control: FANUC, weight: 5t. Bcrj8cpdb0 more
1

CNC thread grinder JUNKER Tapomat 325

Bretzfeld-Schwabbach, GermanyGermany dealership location
6655 km
2001
ready for operation (used)
Control: FANUC SERIES 15-T, MARPOSS E 78. FANUC Robot, pendulum device in the table on a curve, Sanding discs-puller using a diamond roll, CO2 extinguishing system. Thread diameter 3-25.4 mm Thread length of max. 150/180 mm Clamping length 45-250 mm Thread pitch and depth can be programmed Grinding wheel diameter 300-400 mm Grinding wheel width 7-28 mm Power 35 kVA Machine weight approx. 10 t Accessories: Hfckaurco Shuttle feed and pendulum disc, tailstock, diamond dressing wheel.... more
5
Bcsuy9p0rs cylindirical grinder with CNC SIEMENS SINUMERIK 840 and MARPOSS In-Process Measuring Control ; All sales are subject to the seller's consent. Delivery date: about 3-4 days. At location/Fundament. more
1

Disk erosion machine (CNC controlled) Vollmer QM 71 P

Genshagener Str. 27 7A, 14974 Ludwigsfelde, DEGermany
6743 km
1998
refurbished (used)
EDM machine (CNC controlled) Make Vollmer, type QM 71 P Description: Suitable for automatic editing of PCD fitted shaft tools, cutters, disc-shaped tools such as saws, cutters etc. after the disc-electric erosion process. Bd9vqiby Technical data: Cutter diameter of 250 mm, cutting length of 100 mm, Schaftwerkzeugdurchmesser of 10-100 mm, cutting length of 100 mm, outer diameter disc-shaped tools of Max 380 mm, outer diameter disc-shaped tools with surface of Max 520 mm,. Tool weight ... more
3

Roll Grinders CHURCHILL TWR

Willich, GermanyGermany dealership location
6368 km
used
grinding diameter 1520 mm grinding length 6000 mm grinding wheel size 660 mm total power requirement . kW weight of the machine ca. . t Hsm9vbn dimensions of the machine ca. . m 2 Steadies Coolant System more
6

Roll Grinders HERKULES WS200

Großhansdorf, GermanyGermany dealership location
6497 km
used
control Siemens Simodrive 611 Hdijkxhhy dimensions of grinding wheel 450 x 40 x 203 mm more
10

AUTOMATIC BORING MACHINE (CNC Controlled BIESSE Techno 2000 FDT CN

Via Savigliano 29, 12062 Roreto Di Cherasco (CN), ITItaly
6776 km
reconditioned (used)
ELETTRONIC machine, controlled by CNC Numerical Control Type NC 500 (Software Tooling System) Through-feed motorized conveyoring belts (No.) 2 Horizontal units/supports (No.) 2 Drilling heads for each horizontal unit (N°) 2 Splindles for each horizontal drilling head (N°) 11 Max. working width (mm) 3200 - Min. working width (mm) 205 (ca.) Bottom vertical units/supports (No.) 7 Drilling heads/blocks for each bottom vertical unit (N°) 2 Gmeukqif3 Top vertical units/supports (No.) 2 Dril... more
1
Description: Suitable to regrind and manufacture wood and metal working tools of all kinds. Specifications: Working range: longitudinal traverse (X- axis) 460 mm, vertical traverse (Y-axis) 320 mm, cross traverse (Z-axis) 660 mm, rotary table swivelling range (C-axis) +/- 200°, work head spindle ISO 50, max. diameter of workpiece 320 mm, max. length of workpiece for peripheral grinding 350 mm, max. dia. of grinding wheel 200 mm, peak performance 7 kW, grinding spindle speed 0 - 8000 rpm., c... more
1

Disk erosion machine (CNC controlled) Vollmer QM 75 P

Genshagener Str. 27 7A, 14974 Ludwigsfelde, DEGermany
6743 km
2000
refurbished (used)
EDM machine (CNC controlled) Make Vollmer, type QM 75 P Description: Suitable for automatic editing of PCD fitted shaft tools, cutters, disc-shaped tools such as saws, router etc. According to the Schleiben-electro-erosion process. Technical data: Cutter diameter of 250 mm, cutting length of 100 mm, Schaftwerkzeugdurchmesser of 10-100 mm, cutting length of 100 mm, outer diameter disc-shaped tools of Max 380 mm, outer diameter disc-shaped tools with surface of Max 520 mm,. Tool weight ... more
16

Spiral Groove grinding (cylindrical) ROLLOMATIC CNC 12.0

Brügg, SwitzerlandSwitzerland dealership location
6614 km
ready for operation (used)
Technical data Drill diameter min. 0.2 mm Cjtwalta Drill diameter max. 6 mm Drill length 0-80 mm ... more


cnc roll g...
daily

New machines via email!

Stay updated!

to

to

Edit search
CNC ROLL GRINDER
SELL IMMEDIATELY
with Europe's market leader for as little as € 0,49 per ad.
Find out more


Phone: +1 312 94 04 581
or sell immediately
Try our Machineseeker app now!
Machineseeker app for iPhone and Android.
Want to really stop the chat history?
Yes No
×
Machineseeker chat
Name E-mail Your message to the Dealer
START CHAT WITH DEALER
  You are chatting with: 
  Your contact person: 
  
Your contact is typing
SEND MESSAGE
  You are chatting with: 
  Your contact person: 
  
Your contact seems to be inactive
Chat window close