Diesel welder buy used

Recognised location: Ashburn (US) (Change)
Enter e-mail address
or
Move
5
Diesel pump, oil pump speed 930 rev / min motor power 0.55 KW dimensions 420/400/H220 mm mm Weight 20kg Qlqwkcoax more
5
weight max. in kg 3000 kg stroke 2500 mm Gubsak fork length 1400 mm total power requirement kW weight of the machine ca. 4,5 t dimensions of the machine ca. 3,6 x 1,6 x 2,4 m New brakes and complete service in 2015 more
5
welding current max. 320 A at 30 % ED; 250 A at 60 % ED, 195 A at 100 % ED adjustment range 40 to 320 A 9gxn8y0oc 4 step coarse - 10 step fine separate feeder unit Feed 304 four-roll wire feeder intermediate hose pack approx. 7.5 m welding hose pack - 4 m - air-cooled electrical data 400 V space requirements length - 900 x width - 425 x height - 1,150 mm weight approx. 165 kg more
5
IntNr.: 4555 * Device details: * Load capacity: 6000 kg Lifting height: 4000 mm Mast type: Standard mast height: 2840 mm Length/width/height: 3700 / 2050 / 2440 mm Operating weight: 8000 kg * Equipment: * * Protection umbrella * 3rd valve * 4 valve Ibtbpya * Full cab * Working lights front * Working light rear * Front disc is missing * Attachments: * * Side-shift * Tine adjuster The vehicle is offered, in the current status, as of the previous owner without warranty and ... more
6
LINDE H 25 D with Deutz diesel engine Year of construction: 1984 operating hours: approximately 7700 h Duplex masts with approx. 3200 mm lifting height lifting capacity 2500 kg, weight 4450 kg, Sideshift Forks in good condition, to immediately start battery 2016 replaced one of the two high pressure hoses for side-shift and 3rd is control circuit defective we can on request at an additional cost do (+ €200), ready to use Dpsec7g more
2
Circular seam welding machine Cypress welding equipment Model: CW7AB Serial #: L961142 Stroke: 468mm Longitudinal adjustment: 1600 mm Consumption: 900mm Longitudinal bracing height adjustment: 0-70 mm with feed and powder container Koyqlwfj more
5
Converter for Flaschenrüttler, vibrator, poker vibrator drive Hatz diesel inverter 2x vibrators cable length a 6m-weight 100 kg Qlm3eall7 more
6
weight max. in kg 2000 kg stroke 3600 mm fork length 1000 mm allowable maximum weight 5.800 T axial load - rear 2.600 kg axis load in front 5.000 t weight of the machine ca. 3.800 kg. 9jhrr2fc3 more
5
welding current max. 400 A at 52.5 % ED; 345 A at 70 % ED, 290 A at 100 % ED adjustment range 50 to 400 A 2 step coarse - 12 step fine separate feeder unit WEGA drive 9gxoikacd four-roll wire feeder intermediate hose pack approx. 12 m welding hose pack - 4 m - air-cooled electrical data 400 V space requirements length - 1,000 x width - 550 x height - 1,150 mm weight approx. 230 kg more
6
IntNr.: 5597 * Device details: * Load capacity: 2500 kg Lifting height: 4710 mm Free lift: 1500 mm Mast type: triplex mast height: 2112 mm Length/width/height: 2660 / 1260 / 2140 mm Operating weight: 4435 kg * Equipment: * * Protection umbrella * 3rd valve * Windscreen * Roof cover * Working lights front * Bluespot On request we take care of transport to you. Another 250-300 forklifts, attachments and sweepers for you available immediately. I3phf9nr Also for rent! We... more


diesel wel...
every day

New machines via email!

Be informed!
2
lifting capacity in kg: 3000 kg lift: 4520 mm fork length: 1000 mm operating hours: 15.593 h weight of the machine approx.: 4750 kg space requirements of the machine approx.: L:3,8 x B:1,3 x H:2,95 m Forklift is inspected thoroughly & ready to start front lift truck Double lift frame Overall height: 2950mm Fork carriage width: 1100mm (DIN 15173B) Without side shifting device Load center: D=500mm S8zmxjwn9 checked and functional! Documents from a similar equipment available more
3
Welding transformer, small, lightweight, portable, robust - workshop, construction, agriculture Fj007u93 130 A 230 V connection for electrodes of 2.5 3.25 mm with electron holder and work clamp Weight approx. 13 kg more
5
Diesel tank system, diesel tank, gas station, fuel tank system br / br / -Tank of working platforms the company GSL (German Standard Lift) br / -universell usable br / -for diesel, heating oil, gasoline br / contents 28 liters br / -2x tanks available br / prize piece br / -dimensions 450/210 / H310 mm br / -Leergewicht 7.6 kg Cp2tnw02g more
5
Diesel forklift Clark C500Y100 year 1990 trip lex mast with full free lifting height 2200 mm lifting height of 4000 mm of load-bearing capacity 5000 kg hours read off approx. 2100 no sales to private The sale is carried out only to entrepreneurs in the sense of § 14 BGB Ciqtr32 more
5
welding current max. 400 A at 52.5 % ED; 345 A at 70 % ED, 290 A at 100 % ED adjustment range 50 to 400 A 2 step coarse - 12 step fine Mz30f separate feeder unit WEGA Drive four-roll wire feeder intermediate hose pack approx. 10 m welding hose pack - 4 m - air-cooled electrical data 400 V space requirements length - 1,000 x width - 550 x height - 1,150 mm weight approx. 215 kg more
6
IntNr.: 4521 * Device details: * Load capacity: 3000 kg Lifting height: 3550 mm Mast type: Standard mast height: 2450 mm Length/width/height: 2800 / 1250 / 2120 mm Operating weight: 4360 kg 9ph8d7cqo * Equipment: * * Protection umbrella * 3rd valve * Windscreen * Roof cover * Soot filter * Working lights front small maintenance druchgeführt Color new Operating status. Vehicle is not free of defects. On request we take care of transport to you. Another 250-300 forklift... more
6
lifting capacity in kg: 7500 kg lift: 3600 mm Yqabck fork length: 60x200x2000, Seitenschieb mm Lifting height: 4720 mm weight of the machine ca.: 9,86 t space requirements of the machine approx.: L:5,7xB:2,62xH:2,8 m lifting height fork:3600mm lifting height total: 4720mm fork carriage hydr. adjustable ready to start! [...] more
5
water-cooled gas protection welding machine with separate wire feed case welding area: 30-430 430 â 35% ED 350 A at 60% ED 290 A 100% ED protection type: IP 23 power supply: 400 V with hose package and 10 m intermediate tube package, four rollers in the case Tpaggx8t more
5
Diesel tank system, diesel tank, gas station, fuel tank system br / br / -Tank of working platforms the company GSL (German Standard Lift) br / -universell usable br / -for diesel, heating oil, gasoline br / contents 22 liters br / -1x tanks available br / prize piece br / -dimensions 450/200 / H280 mm br / -Leergewicht 4.6 kg Uv8cfsqph more
5
weight max. in kg 3000 kg stroke 2500 mm fork length 1400 mm total power requirement kW weight of the machine ca. 4,5 t dimensions of the machine ca. 3,60 x 1,60 x 2,40 m Etuaf2c9e New brakes and complete service in 2015 more
5
welding current max. 400 A at 52.5 % ED; 345 A at 70 % ED, 290 A at 100 % ED adjustment range 50 to 400 A 2 step coarse - 12 step fine Gvcs8g separate feeder unit WEGA Drive four-roll wire feeder intermediate hose pack approx. 12 m welding hose pack - 4 m electrical data 400 V space requirements length - 1,000 x width - 550 x height - 1,150 mm weight approx. 225 kg more
6
IntNr.: 4363 * Device details: * Load capacity: 3000 kg Lifting height: 3050 mm Free lift: 150 mm Mast type: Standard mast height: 2264 mm Length/width/height: 2755 / 1256 / 2280 mm Operating weight: 4365 kg * Equipment: * * 1200 mm tines other lengths on request * Protection umbrella * Trailer hitch * Working lights front * Working light rear 9ph8noiep New starter battery On request we take care of transport to you. Another 250-300 forklifts, attachments and sweepers fo... more
6
lifting capacity in kg: 10 000 kg lift: - mm fork length: 1500 mm Vrxlse lifting height: ca. 4700 mm Number of working hours: 7325,5 h weight of the machine ca.: 17,0 t dimensions L x W x H: 6,8 x 2,5 x 3,0 mit Zinken/with forks! m dimensions L x W x H: 4,7 x 2,46 x 3,0 ohne Zinken/without forks! m FRONT FORKLIFT - soundproof safety cabin - 6-cylinder diesel engine (Perkins), 84 kW at 2500 rpm, fuel consumption 6 - 7 dm³ / h - fork extension 2.15m - dimensions including extension: 6,8x2,46x3,0... more
2
1 Tig welding machine, used AC or DC, 300 A at 60% ED, 230 (A) 100% ED, with hose Pact, faucet, 63 A plug, water cooled with high frequency ignition Thyristor control Dimensions approx. 1.010 x 530 x 800 mm weight approx. 220 kg Q9nxm7eoi more
5
Diesel tank system, diesel tank, gas station, fuel tank system br / br / -Tank of working platforms the company GSL (German Standard Lift) br / -universell usable br / -for diesel, heating oil, gasoline br / contents 50 liters br / -2x tanks available br / prize piece br / -dimensions 450/405 / H300 mm br / -Leergewicht 11.2 kg Uv8cpdwdi more
1
Bohziw8fDiesel filling station (5.000 l) SMA-REF-6132 Type: other storage 5.000 l Fuel: Diesel Condition: ready for action Location: Eastern Germany Availability: on demand Terms of delivery: ex works free on truck Terms of payment: 100% before dismantling/loading more
3
welding current max. 400 A at 52.5 % ED; 345 A at 70 % ED, 290 A at 100 % ED adjustment range 50 to 400 A 2 step coarse - 12 step fine 9gxor2fwe separate feeder unit WEGA Drive four-roll wire feeder intermediate hose pack approx. 10 m welding hose pack - 4 m - air-cooled gas pressure gauge electrical data 400 V space requirements length - 1,000 x width - 550 x height - 1,150 mm weight approx. 215 kg more
6
IntNr.: 4417 * Device details: * Load capacity: 4500 kg Lifting height: 4600 mm Free lift: 1510 mm Mast type: triplex mast height: 2480 mm Length/width/height: 3030 / 1450 / 2410 mm Operating weight: 6595 kg * Equipment: * * Protection umbrella * 3rd valve * 4 valve * Windscreen * Rear window * Full free lift * Heating * Working lights front 9ph70l33n * Working light rear Renewed work lights Vacuum pump replaced Replaced speed sensor Tilt sensor replaced On request w... more
5
A TOP LINDE H60D Diesel 6000kg Forklift for Sale. Forklift is built 2007 but has only 13292 hours on the tachometer which is not much for such a device. The forklift is visually and technically in a perfect condition. Service was just recently done, including all oils and filters.   Double tire for reduced point load on the ground so that the 10500kg dead weight and additional 6000kg load do not sink into the ground / tar is, of course, mandatory and also available. Tires are good.   The forklif... more
3
WIG welding-machine AC DC 200 A weight: appr. 37.5 kg Fsu7yw0 dimensions: appr. 340 x 500 x 560 mm more
5
Diesel tank system, diesel tank, gas station, fuel tank system br / br / -Tank of working platforms the company GSL (German Standard Lift) br / -universell usable br / -for diesel, heating oil, gasoline br / contents 25 liters br / -4x tanks available br / prize piece br / -dimensions 290/445 / H220 mm br / -Leergewicht 5.4 kg Uv8cyu2xj more
6
3 pieces of welding machines LINCOLN ELECTRIC Invertec V350 PRo Year of production: 2010 (used 3 years) Welding methods MMA, TIG Lift, MIG / MAG, FCAW, arch gouge. 1 set contains: - Invertec V350 PRO power source M3i7f - wire feeder LF-37 - COOL ARC TM 25 cooler - controller - reducer - power cord - wire cooler - wire feeder 1 of the sets contains a transport trolley The price is for 1 device. more
5
welding current max. 400 A at 50 % ED; 650 A at 60 % ED, 280 A at 100 % ED adjustment range 50 to 400 A 4 step coarse - 10 step fine separate feeder unit MEK 2 four-roll wire feeder Dalvyzl intermediate hose pack welding hose pack - 4 m - air-cooled electrical data 400 V space requirements length - 1,100 x width - 550 x height - 1,250 mm weight approx. 185 kg   more
6
IntNr.: 4741 * Device details: * Capacity: 7000 kg Lifting height: 6340 mm Mast type: Duplex mast height: 4170 mm Length/width/height: 3405 / 1748 / 2720 mm Operating weight: 11700 kg * Equipment: * * Protection umbrella * 3rd valve * 4 valve * Full cab * Soot filter * Heating Rw8irjul * Working lights front * Working light rear * Radio On request we take care of transport to you. Another 250-300 forklifts, attachments and sweepers for you available immediately. Also f... more
6
-EZ 10/2015 -27.780 km -Max. Total weight: 3500 kg -Engine power: 120 KW -Number of axles: 2 -High roof -Eliminating partition -Base unit combination -Hardwood floors -Interior cargo space to roof height (wood) -Fabric Tunja black -Electronic stability program (ESP) -Two-stage rear spring -Stabilizer front axle -Reinforced shock absorber -Manual transmission 6-speed ECO gear 360 -Main tank 100 l -Fuel pump electrically controlled -Vehicle low in pollutants Euro 5b + Gr.lll -En... more
6
ride-on-sweeper with cabine and diesel-motor 1 side-brusch sweeping-width 1,52 m theor. capacity: 30.500 qm/h hydraulic high dump working hours: 1060 h Izcswbp motor 50 HP speed max. 20 km/h electric filter agitator electric starter SE-wheels weight appr. 1810 kg dimensions appr. 2480 x 1440 x 2030 mm more
5
Inert gas welding equipment, protective equipment Gas br / br / -max. Welding power 160A br / -2-roller drive br / br -Luftgekühlt / -incl. Ground wire br / br -Gasarmatur / -Schlauchpaket 2.5m br / -dimensions 800/360 / H700 mm br / weight 68 kg Cyd7kqmcc more
4
Tig Welder Roewac Power: 250 Ampère / 60% 200 Ampère / 100% Stick: Jupijy Kemppi TTC 200W Water-cooled Featured with: - Water-cooling - Hose 3 mtr. - Footcontrol RT11F Connetion: 380 Volt Country of origin: Holland Machine weight: 150 kg Machine LxWxH: 1300 x 400 x 820 mm more
5
welding current max. 380 A at 50 % ED; 350 A at 60 % ED, 280 A at 100 % ED Gvd2vk 4 step coarse - 10 step fine separate feeder unit Feed 304 four-roll wire feeder intermediate hose pack approx. 8 m welding hose pack - 4 m - air-cooled electrical data 400 V space requirements length - 900 x width - 500 x height - 1,200 mm weight approx. 210 kg more
6
IntNr.: 4846 Egeh2k9im * Device details: * Load capacity: 5000 kg Lifting height: 3100 mm Free lift: 1500 mm Mast type: Duplex mast height: 2400 mm Length/width/height: 3100 / 1430 / 2370 mm Operating weight: 6485 kg * Equipment: * * Protection umbrella * 3rd valve * 4 valve * Full cab * Full free lift * Soot filter * Heating * Working lights front * Working light rear * Attachments: * * Side-shift * Tine adjuster Fuel filter replaced Replaced heater valve Replaced ... more
6
HAKOTRAC 2000Diesel tractor German tractor with Italian engine 9yudwwvlv Lombardini engine 1 cylinder 18KM The tractor is fully efficient Of Light, directions, podnosnik, propellor Burn the starter 2 reverse gears, 3 forward gears plus fast forward and reverse gears Alternator after regeneration 1573 hours A book with a list of parts I recommend the fully Efficient Technically more
2
with HATZ diesel engine 42 kW Max cutting depth 100-150 mm ABM. approximately 630 x 1420 x 1100 mm weight: 228 kg max weight: 259 kg cutting speed: 2500 rpm hand held with start crank for saw blades d-300 / 350 / 400 mm Uzhm3tno more
5
Diesel motor, drive motor -3 cylinder air-cooled-engine has an output of about PS is a spare part carrier sold-dimensions 1200/800/H1050 mm Weight 360 kg Rghppqzm7 more
6
6-cylinder diesel engine VOLVO type: TID 71 A - 353-60127 BJ. 90 Performance: 197KW,Hubraum 6727 CM³. 7kbq0xeod more
5
welding current max. 380 A at 50 % ED; 350 A at 60 % ED, 280 A at 100 % ED 4 step coarse - 10 step fine separate feeder unit Feed 304 four-roll wire feeder M2frj intermediate hose pack approx. 8 m welding hose pack - 4 m - air-cooled electrical data 400 V space requirements length - 900 x width - 500 x height - 1,200 mm weight approx. 210 kg more
6
IntNr.: 5626 * Device details: * Load capacity: 3000 kg Lifting height: 4000 mm Mast type: Standard mast height: 2600 mm Length/width/height: 2680 / 1220 / 2060 mm Operating weight: 4810 kg * Equipment: * * Protection umbrella * 3rd valve * Working lights front * Working light rear Operating status, such as by the customer back Hours of operation according to the clock On request we take care of transport to you. Another 250-300 forklifts, attachments and sweepers for you ... more
6
Forklift fully functional MITSUBISHI FD40 6 cylinder diesel engine Side shift 8qn2w9jxx Weight 4000kg, Possibility of video recording and sending more
3
Note our numerous offers from heavy wash like we advise you Contact us self propelled brush wash with water tank Vj8xzi8u9 Sold signs Yes is possible as shown - export more
5
Inert gas welding equipment Inert gas equipment welding rectifier br / br / -max. Welding power 150A br / 2-roller drive br / br -Luftgekühlt / -With detachable wire feed br / -incl. Ground wire br / br -Gasarmatur / -Schlauchpaket 3.8 m br / -Zwischenschlauchpaket 22.6 m br / -dimensions 80/500 / H1200 mm br / weight 140 kg Kp3i208b more
6
We offer: from the part of stock of insolvent SEAT car House Diesel filter stage filter pre-filter Filu IFA W50, ZT, Takraft For the following vehicles. TRUCK W50 / L60 ZT tractor... Forklift Takraft Manufacturer: VEB filter construction "Daniel Radcliffe" Berlin Meterial: steel housing with filter fabric Type: B Size: F Flow capacity: 90 l / h D: 50 mm H: 115 mm D3kdq82ck Weight: 145 g After 90013458 TGL (just for comparison purposes) Cleaning after 4000 bra with deg... more


diesel wel...
every day

New machines via email!

Be informed!

to

to

Change search
DIESEL WELDER
SELL IMMEDIATELY
on Europe's market leader for as little as € 0,79 per ad.
Find out more now


Phone: +44 (0) 20 806 810 84
or sell immediately
Try our Machineseeker app now!
Machineseeker app for iPhone and Android.
Want to really stop the chat history?
Yes No
×
Machine Finder chat
Name E-mail Your message to the Dealer
START CHAT WITH DEALER
  You are chatting with: 
  Your contact person: 
  
Your contact is typing
SEND MESSAGE
  You are chatting with: 
  Your contact person: 
  
Your contact seems to be inactive
Chat window close