Used Galvanotechnik Leipzig for sale (613)

Condition: used, Year of construction: 1985, Technical details: Punching capacity: 40 kN air pressure - required: 8 bar ram stroke - adjustable min/max: 6 - 50 mm ram adjustment: 50 mm no. of strokes: 70 - 400 Hub/min Table dimensions: LxB: 480 x 445 mm hole in table: LxB: 250 x 112 mm slowing-down time: 80 ms bei 450 U/min. clamping surface ram: LxB: 420 x 345 mm Lhedju Icwgepfx Aa Dsp ram hole: Ø 40 x 230 mm voltage: 380 V control voltage: 220 V frequency: 50 Hz total power requirement: ca. 19 kVA (ca. 7,5 KW) weight of switch cabinet: 0,3 t machine weight ab.: 4000 kg 40t punching press without roll feed/conveyor belt system Operation via control panel / two-hand operation Operation: manual / automatic *

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 1240x950x1650 mm Lhsdpfx Aov A Hdcja Djp Weight 435 kg Total power requirement 4,65 kw

Condition: excellent (used), functionality: fully functional, machine/vehicle number: P21120V02510, Year of construction: 2019, operating hours: 550 h, load capacity: 1,400 kg, lifting height: 4,800 mm, fuel type: electric, mast type: triplex, battery capacity: 620 Ah, battery voltage: 48 V, Equipment: cabin, sideshift, Linde R14-01 Triplex Reach Truck – Excellent Condition 2019/550h For sale is a very well-maintained Linde R14-01 reach truck from 2019, with only 550 operating hours. The machine comes from a meticulously cared-for industrial fleet and is in impeccable technical and visual condition. Technical Specifications: • Manufacturer: Linde Material Handling • Model: R14-01 (R14 1120) • Year of manufacture: 2019 • Serial number: P21120V02510 • Load capacity: 1,400 kg at 600 mm load center • Mast type: Triplex 1501 • Lift height: 4,800 mm • Free lift: approx. 1,500 mm • Height (retracted): approx. 2,100 mm • Battery voltage: 48 V • Battery capacity: 560 / 620 Ah (4 PzS), including charger and stand • Drive power: 6.5 kW • Unladen weight (incl. battery): 2,460 kg • Battery weight: approx. 590 kg • Operating hours: 550 h Features & Condition: • Triplex mast with free lift (optimal visibility and high lifting performance) • Side shift Lodpfx Aasxub Rwe Dshp • Fully functional and ready for immediate use • Battery in very good condition with proper charging capacity • CE marking present • Immediately available • Transport possible on request • The unit is located in Bavaria near 94469 Deggendorf; viewing and collection possible until the end of 2025 Pricing: Negotiable price – realistic offers welcome.

Condition: excellent (used), functionality: fully functional, Model: Portioning Conveyor - Forming Machine Add-on Cevapcici Line Height adjustable digitally controlled conveyor belt (300 mm wide) including paper holder for rolls up to max. 600 m Lhjdpfx Aaoxa Al Ho Dep belt speed adjustable via filler control (TC) PBSE: incl. cutting unit, only in combination with CLB air requirement 6 bar, approx. 70 Nl/min Exclusion of warranty and guarantee; purchased as seen Net sales price reduced from €9,900.00 to €8,500.00 (purchase price net €18,012.00) Condition: device is in very good condition and fully functional! Invoice with VAT shown separately Collection: from our warehouse Shipping possible on request at buyer’s expense

Condition: ready for operation (used), functionality: fully functional, For sale is a folding machine from the brand Schuler (see pictures). It is used but in excellent and fully functional condition. Bending width: 200 cm. Lodpfow Taf Ssx Aa Dehp

Condition: used, mileage: 73,973 km, power: 96 kW (130.52 HP), fuel type: diesel, gearing type: automatic, overall weight: 3,240 kg, first registration: 12/2018, emission class: euro6, color: silver, number of seats: 9, Year of construction: 2018, total width: 2,032 mm, total height: 1,965 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, soot filter, Subject to errors and prior sale! Internal number: 1050. TA JR38477----LOCATION: 04425 Taucha, Leipziger Str. 102 Tel. no. for inquiries: Mr. Ingo Hinze: by email: ----EQUIPMENT * Trailer hitch - fixed, 13-pin socket - including trailer stabilization (TSC) * Exterior mirrors, electrically adjustable, heated and foldable with blind spot assistant - with integrated indicators - Blind spot assistant including Cross Traffic Alert Lodpjrxpu Rsfx Aa Dshp * Air conditioning front and rear including water heating rear * Paintwork: metallic * Visibility package III - heated windshield - washer fluid sensor - windshield wipers with rain sensor - headlight assistant with day/night sensor - lane assistant with fatigue warning and high beam assistant - rear view camera with image transmission of the rear path in the multifunction display, additionally with coupling aid in conjunction with trailer hitch * Audio system 24: Ford audio system including Ford SYNC 3 with AppLink, DAB/DAB+ and navigation system. Radio (FM/AM) 8" TFT multifunction display (20.32 cm screen diagonal) 10 speakers Antenna 8 USB ports Integrated control panel and audio remote control on the steering wheel Ford SYNC-3 (communication and system, Bluetooth, USB, integration of various telephony functions and hands-free system, voice control, SMS reading/sending function, private mode, emergency call assistant...) AppLink (control of other smartphone apps via voice command, ...) Navigation system Road map for Western Europe * Voltage converter - (230 V/0 watts) Plug-in connection e.g. for connecting a laptop or charging a mobile phone * Heat-insulating glazing, side windows from 2nd row, medium tint * Anti-lock braking system with electronic brake force distribution (EBD) * Airbag on driver and passenger side * Windows, 2nd row: hinged windows in the side windows * Exterior mirrors, electrically adjustable, heated and foldable - with integrated indicators * Floor covering: carpet * On-board computer with consumption and mileage information (e.g. B. remaining range) and outside temperature display * Roof, flat * Roof lining in passenger compartment * Roof lining in driver's cab * Tachometer * Electronic safety and stability program (ESP) with traction control (TCS) - Hill start assist - Crosswind assist - Safety brake assist - Rollover protection * Windows: 3rd row window in passenger compartment, fixed, right and left * Electric window lifter with quick down/up switch for driver's side * Ford Easy Fuel - comfort tank cap and misfueling protection * Generator, 0 A * Cruise control system with adjustable speed limiter * Gearbox: 6-speed SelectShift automatic transmission * Headlight dipped beam: Halogen projector headlights with LED daytime running lights and fog lights with static cornering lights * Grab handles (B-pillar) * Grab handles (driver's and passenger side) - incl. storage compartment, small, in the middle (1 DIN slot) * Glove compartment with lockable lid * Rear swing door with heated rear window and wiper/washer system - rear window wiper (automatic when reverse gear is engaged including windshield washer nozzle) * Water heating at the rear * Interior lighting at the front and rear with delay circuit - additionally with reading lights at the front * Leather steering wheel * Steering column, adjustable in height and reach * Emergency brake support including emergency brake light - pulsating illumination of the brake light

Condition: used, Technical details: x-travel: 800 mm y-travel: 460 mm z-travel: 620 mm control: YASNAC-J50M table-size: 1100 x 460 mm table load capacity: 800 kg tool taper: BT40 Revolution per minute: 30 - 10 000 U/min. spindle head: MAS / BT 40 distance spindle nose and table: 150 mm feed speeds infinitely variable: 8 m/min. rapid traverse:: x+y+z: 30+30+24 m/min tool changer with: 24 spindle hours: 1317 h operating hours - idle run: 7148 h air-pressure connection: ja bar total power requirement: 30 (kVA) Weight approx.: 5,0 t dimension machine xH: 2,9 x 2,5 x 2,85 m dimension swarf conveyor LxWxH: 3,0 x 0,9 x 1,3 m other technical characteristics: max. drill Ø 40mm Facing 245 cc/min (cc/min) Thread cutting up to M 36 Compressed air connection Equipment: Chip conveyor with cooling water tank Interior lighting Ledpfx Aaeu Idf Es Dehp Operation via swivelling control panel CTS Machine feet Accessories: approx. 26 clamping spigots *

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 2960x1500x2000 mm Weight 4000 kg Total power requirement 19,5 kw Lhsdpfx Aev A Hkioa Dsp

Condition: used, Year of construction: 1995, Technical details: Table dimensions: 920 x 620 mm voltage: 220 / 50 V / Hz total power requirement: 0,77 kW weight of the machine ca.: 0,11 t dimensions L x W x H: ca.0,92 x 0,62 x 0,80 m Strapping Machine Semi-automatic machine for plastic strapping (approx. Ø 500 x 17mm) Lhjdpfx Aevc Axcsa Dsp Strap holder located in the base cabinet table surface folded with 1,5mm chrome plate with stop LxWxH 345 x 80 x 20mm, adjustment approx. 32mm The adjustment of the tightening is done by display on linear scale. The packaging machine is mobile and easy to move = 4 castors, swiveling and 2 castors are braked. *

Condition: used, Year of construction: 1985, Technical details: pressure: 100 t no. of strokes: 35-100 Hub/min throat: 360 mm ram adjustment: 20-130 mm ram surface area: 750x550 mm clamping plate on table: 1000x640 mm adjustment of stroke: 90 mm passage between the columns longitudinal/sideways: 610x500 / 440x550 mm daylight dimension : table/slide low: 300 mm total power requirement: 17,5 kW weight of the machine ca.: ca,7,0 t dimension machine xH: 1,9x1,4x2,7 m - there are 5 T-slots lengthwise on the ram plate - centre hole = 50mm This press is currently for sale without controls. Optional on customer request completion possible. Lsdpfx Aaou Nfh De Dshp i.D. *

Year of construction: 1998, condition: used, Technical details: Ledpfx Aaju Ibuws Dehp profile width: 50 mm work height max.: 950 mm interface: RS 232 Pinout Window profile processing machine for materials such as plastic, aluminum and wooden windows in a continuous process. The materials are conveyed by a pneumatic transport and clamping system. The system consists of two work stations (machines), an electrical control cabinet, and a control panel and transport units. As well as columns with transport system vibrator, chip transport unit and column with receipt printer. Our photos are first taken from the location and then further pictures are how the plant is stored in our stock ready for transport. Workstation no. 1 (machine 1): -sawing station with saw blade Ø 400 x 4,5mm -drilling unit with clamping cartridge (vertical upwards) -drilling unit with clamping cartridge (hotizontal) -Boring with clamping cartridge (vertical down) -twin drilling unit with clamping cartridge (vertical down) -45° drilling unit with clamping cartridge (upwards) Working station no. 2 (machine 2): -drilling unit with clamping cartridge (vertical upwards) -milling spindle horizontal with 11 side milling cutters -Drilling unit with clamping cartridge (vertical down) -Drilling unit with clamping cartridge (vertical upwards) -Drilling unit with clamping cartridge horizontal 2 transport units: motor driven -LxWxH: 5.650 x 2.400 x 1.000mm -track width 1.980mm 2 pieces transport units: motor driven -LxWxH: 2.150 x 2.750 x 1.050mm -track width 2.300mm *

Condition: used, Technical details: plate width: 1000 mm plate thickness: 1 mm distance between columns: 1220 mm knife length: 1030 mm stroke adjustment: Oberwange: 100 mm stroke adjustment: Biegewanne: 45 mm bending angle max.: 140 ° weight of the machine ca.: 0,65 t dimension machine xH: 1,8 x 0,6 x 1,1 m Ljdpfsu Ibz Rox Aa Dehp - This swivel bending machine is equipped with two rear supports. Size of the round steel support = Ø 25 x 750mm, with linear scale. - Left side with counterweight. *

Condition: used, Technical details: tube diameter: siehe o mm Lodpfx Aaju Icu So Dshp wall strength: siehe o mm voltage: 230 V / 1Phase V total power requirement: 0,55 kW machine weight approx.: 56 kg dimensions L x W x H: 0,45 x 0,37 x 0,35 m HYDRAULIC LINE PRESETTING DEVICE for EO pipes Application for crimping flared fittings on hydraulic lines. Crimping of common raw materials such as steel (ST 35.4 NBK and-or ST 37.4 NBK and-or ST 52.4 NBK), stainless steel (1.4571/1.4541/316Ti or similar) and copper pressure-controlled There is a flaring tool for the size Ø 14mm on the machine. The operating pressure is variably adjustable. *

Condition: used, Year of construction: 1988, Technical details: tank: 300 l volume capacity: 350 L/min Lhsdpfxsu Nz Elo Aa Dop connected load: 4,3 kW weight: 340 kg dimensions L x W x H: 1,9 x 0,6 x 1,2 m Compressor: Geraer Kompressorenwerk 2 cylinders; 350 l/min; pressure max. 2.1 MPa, nominal pressure 1.6 MPa Motor: ADDA Antriebstechnik GmbH speed 2.870 / 3.444 rpm; voltage 380V Boiler: Geraer Kompressorenwerk size Ø 550 x 1800m, with 3/4" and 1/2" stop valve, pressure gauge Inspection until 07/2022 done *

Condition: used, Year of construction: 1988, Technical details: throat: 138 mm plate thickness: max. 1,12 mm infeed height: 1125 mm voltage: 380 V total power requirement: 0,25 kW weight of the machine ca.: 0,149 t dimensions L x W x H: 0,9 x 0,6 x 1,4 m -application: bending of beads / flanging -shaft distance max./min.: 65 / 52mm manually adjustable via handwheel -currently beading tool Ø 8mm built in -stop plate 130mm adjustable operation at the control box and via foot switch The machine is mounted on a steel construction. Ljdpfeu Icviex Aa Djhp *

Condition: used, Year of construction: 2002, Technical details: x-travel: 1060 mm y-travel: 610 mm z-travel: 610 mm control: Ultimax 4 spindle speed:: 10 - 10.000 U/min tool taper: SK40 tool changer with: Trommelmagazin mit 24 Plätze places Lhjdpfx Aasu Iddno Dop feed speed: XYZ: 3 - 7.000 mm/min rapid traverse:: XY: 30 m/min rapid traverse: Z: 20 m/min table-size: 1220 x 510 mm table load: 1,1 t air-pressure connection: für 6 bar bar Total power requirement: 30 kVA Weight approx.: 6,28 (ohne Anbauteile) t dimension machine xH: 2,82 x 3,2 x 2,7 m dimension swarf conveyor LxWxH: 3,0 x 0,65 x 1,5 The machine is currently in the technical department. delimited working area by chip splash guard cabin incl. cooling device with feeding (30bar internal coolant system) (size 1200x500x150mm) capacity for 340Liter spindle with internal coolant system Scraper belt chip conveyor control panel with two screens Attention! Tool gripper arm for tool change is missing on the machine! Is on sale with this limitation! i.D. *

Condition: used, Technical details: spindle taper: 40 number of spindles: 9 Stück weight of the machine ca.: 10,0 t total power requirement: 13 (17,5 PS) kW dimensions of machine: LxBxH: 4100x3400x3200 mm dimensions electric cabinet: LxBxH: 2100x350x1900 mm TRANSFER MACHINE DRILL AND THREADCUTTING MACHINE - ROTARY TRANSFER MACHINE with 9x Drill-& Mill Spindles - right 2x Drill-&Mill Spindle from that 1x with U-axis flexible and 1x thread cutting unit with 9 stages flexible - left 2x Drill-&Mill Spindle from that 1x with U-axis flexible and 1x thread cutting unit with 9 stages flexible, such as radial 2x Drill-&Mill spindle and 1x thread cutting unit 9 stages, flexible - workpiece carrier with 8 clamping stations: workpiece holding barrel Ø 1000 mm (oil-pneumatic cycle), clamping station self-centering clamping jaws - Drilling: SK 40 intake; spindle stroke 125 mm; standard feed rate 0 - 2 m/min; RPM at 12 stages with 164-1005 rpm - Drill- and facing unit; SK 40 intake; spindle stroke 90 mm; standard feed rate 0 - 2 m/min; rapid traverse feed rate 7.5 m/min; RPM at 12 stages with 166 - 1020 rpm - 3 piece thread-cutting units: SK 40 Intake; Working stroke 125 mm; RPM at 12 stages with 31.5 - 194 rpm; clockwise and counterclockwise - 6 piece opposing drill units: SK 40 intake Equipment: - coolant system with feed - operation through control panel - chip box - counting mechanism - elevated platform with stairs Lhsdpfx Asu Idwboa Dop i.D. *

Condition: used, Year of construction: 2004, Technical details: balancing body max.: 12500 kg balancing body diameter w/o machining unit: 1500 mm bed length: 3000 mm swing diameter: 2400 über Maschinenbett mm rotor-shaft: Ø 1500 über Bandantreb voltage: 400 / 50 V/Hz drive power: 22 kw connected load: 25 kVA / 20 kW compressed air: 6 bar Weight approx.: ca. 5,5 t dimension machine xH: 3,3 x 1,5 x 2,0 m dimensions electric cabinet: 650 x 610 x 2150 mm Horizontal balancing machine, functional see video, dismantled, ready for loading ex Leipzig. The balancing machine is used to measure and balance the static or dynamic unbalance of rotors. Drive block/balancing speed: 5-speed and reverse gear (manual gearbox) max. 80 rpm; 160 rpm; 290 rpm; 470 rpm; 630 rpm. Lhsdpfx Aou Iczroa Dep incl. PCX measuring electronics Measuring method force-measuring Measuring range of the electronics Speed 60 to 30,000 rpm. Bearing journal Ø 40 - 178mm / 140 - 445mm 2 base bodies (cast steel body), storage length between the bearing pedestals up to approx. 3000mm, adjustment with hand ratchet via toothed rack, with extension 1500mm 2 bearing pedestals/swing bearing blocks: Center height 1200mm measured in bed; 2x rollers Ø 195 x 56mm; 2x rollers; center distance 205mm; adjustment travel 350mm vertical *

Condition: new, This is a new machine which is manufactured in Romania by the manufacturer Emsil. Customer wishes can be taken into account depending on technical implementability and are checked in advance by the manufacturer's engineering office. Narwhal features a drilling spindle that is made of hardened, tempered and rectified alloy steel. It is mounted with preloaded oblique precision ball bearings. The machine is also equipped with a milling and boring bar which can handle exceptional power and torque. Lhjdpfxeu Id H As Aa Djp The bar is made of nitrided alloy steel and is also mounted with oblique preloaded precision ball bearings. It moves on bronze guide bushings. The clamps of both units, used for securing and releasing the tool holder cone with ISO 50 coupling, open and close automatically Rotary Turntable: The table is turned by means of a double pinion gearbox, a central rod wth bearings and hydrostatic sliding block of the centre bearing which is of a suitable size to guarantee maximum precision with large loads, even unbalanced ones. There is a recirculating ball screw slide guide system for the x-axes. Both axes are equipped with a direct measuring system. CNC Axes Control: The 9 axes of the machine are monitored at all times. The monitoring system is equipped with a 15'' TFT screen, a control panel, remote diagnostics that alert the user in case of faults, a user memory, network connectivity, remote control of the process, integrated PLC, etc. The machine is compatible with the multiple control systems such as Heidenhain, Fanuc, Siemens etc. You can choose the sizes of machining of X/Y and Z axes: from 1200 - 3500 / 1000 - 3500 / 400 - 1500mm *

Condition: used, Year of construction: 1993, Technical details: material: PUR Schaum Rotor-Ø: 315 mm compressed air: 6 bar The milling plant with milling and opening-up machine REKORD BR-ex (explosion proof up to 3 bar absolute) is intended exclusively for grinding PUR (polyurethane) foam. Data of the processable material: - pre-comminuted PUR foam pieces max. 20mm - humidity so that milling is still possible - throughput volume=approx. 130kg/h Lsdpfsu Nxdfsx Aa Dehp Drives: - 5 drives (all geared motors) for roller dosing units, mill drive (squirrel cage motor), mixer, discharge screw conveyor, bucket wheel *

Condition: used, Technical details: pressure: 25 t stroke: 500 mm daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm Lhjdpfx Aaevc Awxs Dep ram speed - forward: 0,100 m/s ram speed - reverse: 0,45 m/s Table dimensions: 630 x 500 x 75 mm passage inside table: Ø 180 mm surface area of ram: 450 x 360 mm mortise hole in ram: Ø 32 mm height over floor: 710 mm total power requirement: 8,75 kW weight of the machine ca.: 2,2 t dimension machine xH: 1,7 x 1,1 x 2,95 m Operation via two-hand control panel. (and one-hand operation) *

Condition: used, Year of construction: 1992, Technical details: sheet width: 4050 mm plate thickness: 16 mm distance between columns: 4900 mm Ljdpfx Aju Icpcoa Dshp control for program: Robosoft SC5 Controller back gauge: 1000 motorisch cutting angle: 0,5° - 3° ° cutting gap adjustment: ja / jes mm down holder: 23 Stück height over floor: 1030 mm Table dimensions: L x B 4000 x 520 mm weight of the machine ca.: 19,2 t dimensions of machine: 5,2 x 2,2 x 2,78 m characteristics: - knife length 4100mm, 4 turns possible - Number of strokes: 5 - 11 strokes/min. - Table: side stop with linear scale, with stop bar 1000mm removable, feed aid via / with ball bearings - front support: LxWxH: 1600 x 1100 x 1000 mm; movable over roller rail, easy handling - backgauge adjustable, motor driven and foldable Operation via control panel with jib lenmgth arm and foot control Equipment: - light grid at backgauge - cut line ilumination Accessories: - 1 set (2 pieces) shearing blades *

Condition: used, Technical details: space requirements of the machine approx.: 2x Boxen: 0,85x0,55x0,40 / 0,10x0,55x0,4 m Aramis 3D Camera = robust design for high-end applications with high-resolution 3D sensor. Camera resolution 1936 x 1216 pixel Frame rate (fps) 130 fps at full resolution; 24 fps at 1/2 image height; 450 fps at 1/4 image height: Ljdpfou N Auhjx Aa Dohp Aramis Adjustable = modular and flexible measurement system for research and industry with user-friendly application. without software (only via manufacturer ) *

Condition: used, Year of construction: 1996, Technical details: length: 4000 mm width: 800 mm height over floor: 400 mm Payload: 3,0 t dimensions L x W x H: 4,1 x 0,8 x 0,41 m weight: 0,153 t Lhjdpfeu Nv Syox Aa Dop Several of these "long material trailers" are for sale in Leipzig. The trailers can be coupled together. The drawbar/trolley jack is charged separately, if required. Single axle operation with rigid axle. Solid rubber tires, track spacing = 590mm Sale individually but also in a package from 5 pieces possible. Price on request. i.D. *

Condition: used, Year of construction: 1975, Technical details: turning diameter over bed: 500 mm turning diameter over support: 260 mm turning length: 950 mm center height measured in bed: 220 mm centre distance: 1000 mm revolution per minute: 11,2 - 2240 / 24 step U/min spindle bore of work spindle: 62 mm tailstock quill adjustment:: 210 mm longitudinal feeds:: 0,045 - 1,6 mm/U - 32 step cross feed: 0,02 - 0,71 mm/U - 32 step total power requirement: 11 kW weight of the machine ca.: k.A. t dimension machine xH: 3,3 x 1,2 x 1,6 m The machine is in a very good condition (very quiet spindle run) in Leipzig. Top slide rotatable 360° 3-jaw lathe chuck Ø 315mm with jaws (inside/outside) for speed 2000 rpm. Thread cutting: metric, modular thread, inch Chip protection wall Chuck protection (mechanical) MULTIFIX steel holder with Ø 40mm drill steel holder Chip collection tray Coolant supply with pump Protective device for lead screw Ljdpfxsv A Sqho Aa Djhp Machine base UVV is pre-equipped ( UVV=Accident Prevention Regulations) *