Used Mep Shark 310 Sx for sale (108)

Condition: new, cutting diameter 300 mm saw band length 3320 x 27 x 0,9 mm mm cutting width 300 mm Control NC capacity 90 degrees: flat 330x 260 mm capacity 90 degrees: square 260 x 260 mm capacity 45 degrees: square 250 mm capacity 45 degrees: flat 270 x 200 mm capacity 60 degrees: round 180 mm capacity 60 degrees: square 170 mm band speed 15 - 100 m/min total power requirement 2,2 kW weight of the machine ca. 1,1 t Bljdpfx Aofg E H Eegzob dimensions of the machine ca. 3,3 x 2,83 x 2,23 m Furnishing: - fully automatic electro-hydraulic band saw with additional semi-automatic, semi-automatic-dynamic and manual operation - Automatic cycle (cuts from 0° to 60° left) - Semi-automatic, semi-automatic-dynamic and manual cycle (cuts from 45° right to 60° left) - Manual or semi-automatic dynamic cycle to make cuts outside of series production can be carried out directly without programming. - Numerically controlled band saw machines with the new, especially from MEP Windows CE based controller developed for automatic machines. - User interface with touch screen display of 7 and mechanical buttons for the operating functions of the sawing machine. - Stepless regulation of the cutting speed from 15 to 100 m/min Frequency converter (inverter). - Material feed with stepper motor via ball screw - which is mounted on opposite ball bearings; Single stroke 600 mm - repeatable to cut to any length. - Automatic monitoring of cutting load - through a servo valve mounted directly on the cylinder. - The coolant pan is installed in the base frame - Chip clearing brush. - Bimetal saw band for solid and profile material. - Tools and instructions for use with a list of spare parts

Condition: new, MEP SHARK 281 CCS metal band saw with semi-automatic lowering. Item number: SH281CCS motor power 1,5/1,8 kW band opening 285 mm band dimensions 2950x27x0,9 mm weight 375Kg Speed 36/72 m/min. cutting surface 0° 250 / 230x230/ 280x200 Bjdpfx Aecgbp Iogzelb cutting area 45° right 190 / 180x180/180x180 Cutting surface 45° left Cutting surface 60° right Cutting surface 60° left Description: -Saw band arch, vise unit and base made of resistant cast iron. -Precision degree marking on the cast iron structure -Electrical system (with fully identifiable electrical wiring and low voltage 24 V system) -Switching handle IP 55 for manual cycles (if present) -Rotating scraper brush for the saw band -Closing unit with vice for fast approaching -Accurate stops with adjustment for miter cuts at 0°, 45°, 60° on the left side -bi-metal saw band 2950 x 27 x 0,9 mm -Wrench, instructions for use and instructions for ordering spare parts in the user's language -SHARK 281 with manual operation and SHARK 281 CCS with manual operation and cut with automatic head feed by own weight. -CCS (Cut Control System) with (A switch for manual and automatic cutting - B) regulation of cutting speed - C) hydraulic brake with tank - D) end stop for stopping the belt) also available as an option for machines already in production. -Vice with quick adjustment -Hydraulic transducer for belt tension indication -Electric coolant pump for cooling and lubrication of the saw band and manageable coolant tank above the base frame -For the versions with pneumatic vice (MA), the opening and closing of the vice is done with a manual valve (available as an option with pedal control) MEP SHARK 281 SXI evo [Semi-automatic] Part number SH281SXI motor power 1,5/1,8 kW belt opening 285 mm belt dimensions 2950x27x0,9 mm weight 435 kg Speed 36/72 m/min. cutting surface 0° 250 / 230x230 / 280x200 cutting area 45° right 190 / 180x180 / 180x180 Cutting surface 45° left Cutting surface 60° right Cutting area 60° left Description Semi-automatic function: Vise closes and motor starts, saw head lowers for cut, motor shuts off, saw head raises, vise opens. Some features: - New centralized control panel on articulated arm. - Latest generation hydraulic control unit, highly efficient and with low energy consumption. - Base with extractable coolant tank. The machine complies with CE regulations in all areas! For further technical data, please refer to the attached PDF document.

Condition: good (used), Year of construction: 2002, MEP bandsaw automat Bedpfx Agsw Na T Uszjlb Model Shark 320 AXI Year : 2002 Capacity round : 260 mm. Capacity 45 / 60 degrees : 230 mm. / 150 mm. Capacity square. : 320 x 220 mm. Speed: 40 - 80 m./min.

Condition: new, cutting diameter 250 mm saw band length 2950x27x0,9 mm table height mm band speed 36/72 m/min total power requirement 1,8 kW weight of the machine ca. 440 kg Bedpfxefg E H Ns Agzslb dimensions of the machine ca. m Basic equipment: Vice with quick adjustment and adjustable guide bars Hydraulic band tensioning device with tensioning pressure display Base frame with removable coolant tray Chip clearing brush Precision stops set for cuts of: 0°, 45° and 60° left and 45° right Turntable for double miter cuts Electric coolant device 48 V (A micro spray device can be installed)

Condition: new, MEP band saw machine SHARK 331-1 NC 5.0 Spider All MEP models on request ! Motor power 2,2 kW band opening 340 mm belt dimensions 3650x27x0,9 mm weight 1.240 Kg speed 15 - 100 m/min. infinitely variable cutting area 0° 280 / 260x260 / 330x260 cutting area 45° right 260 / 250x250 / 270x200 Cutting surface 45° left Cutting area 60° right 180 / 170x170 / 170x170 Cutting surface 60° left Description Hydraulic bandsaw fully automatic Miter cuts up to 60° left possible Bodpfechhdijx Agzjlb saw band length: 3650x27x0,9 Single stroke: 600 mm (programmable up to 10m) Simple touch screen operation. Saw arm made of Spheroguss - robust and stable Required floor space 3,4 m² Footprint 1900mm wide x 1800 mm deep For further technical data please refer to the attached PDF document.

Condition: new, 230 mm 230 x 230 mm saw band length 2950 x 27 x 0,9 mm table height mm band speed 15 - 100 m/min total power requirement 2,2 kW weight of the machine ca. 1,2 t dimensions m SHARK 230-1 NC HS 5.0, electro-hydraulic two-column fully automatic band saw with semi-automatic function for 0° cuts of mild steel, stainless steel, Steel alloys, solid and profile material, with a maximum remaining piece length of 60 mm. - The cross section is max. 230x230 mm. - Numerically controlled band saw machines with the new, specially designed by MEP developed for Automatic Windows “CE” based E FEATURES: - User interface with 7” touch screen display and mechanical buttons for the operating functions of the sawing machine, guaranteed reliable Operation, simple and intuitive, and real-time control of all Cutting parameters. Bljdpsfg E Hysfx Agzeb - Safety enclosure in accordance with the latest safety regulations Machinery Directive EN 13898/2007. - New fieldbus communication system with double microprocessor Serial connection. - Robust cast iron structure (G25) to compensate for vibrations Improve machine stability and protect the saw band

Condition: new, MEP SHARK 230-1 NC HS 5.0 Two-column metal band saw Item number SH230-1NCHS motor power 2,2kW band opening 235 mm band dimensions 2950x27x0,9 mm weight 1.000 kg speed 15 - 100 m/min. infinitely variable cutting surface 0° 230 / 230x230 cutting surface 45° right cutting surface 45° left cutting surface 60° right cutting surface 60° left Description: SHARK 230-1 NC 5.0, electro-hydraulic twin-column fully automatic bandsaw with semi-automatic and fully automatic mode. Max. remnant length 70 mm. Bedpfschhfusx Agzolb Bundle cuts 230 x 230 mm. Numerically controlled sawing machine with the new MEP 50- Windows based control. Material feed with stepper motor via ball screw mounted on opposing ball bearings. Single stroke 500 mm - repeatable to saw any length. Easy programming - enter cutting length and number of pieces and press "START". Electronic belt tension control. Automatic monitoring of cutting load by servo valve mounted directly on the cylinder. Rotation control of the band with immediate stop in case of a blocked saw band.

Condition: new, cutting diameter 280 mm saw band length 3320 x 27 x 0,9 mm mm cutting width 330 mm Control NC capacity 90 degrees: flat 330x 260 mm capacity 90 degrees: square 260 x 260 mm band speed 15 - 100 m/min total power requirement 2,2 kW weight of the machine ca. 1,24 t dimensions of the machine ca. 3,3 x 2,83 x 2,23 m Attention: special price!!! •Fully automatic hydraulic band saw •Miter cuts up to 60° left possible •Saw band length: 3650x27x0.9 •Single stroke: 600 mm (programmable up to 10m) •Simple touchscreen operation. Bedpfx Ajfg E H Dogzolb •Saw arm made of nodular cast iron - robust and stable •Required space 3.4 m² •Footprint 1900mm wide x 1800mm deep

Condition: new, MEP SHARK 350 NC HS 5.0 Fully automatic two-column metal band saw Item number MEP SHARK 350 NC HS 5.0 Motor power 4,0kW Bench opening 355 mm band dimensions 4640x34x1,1 mm weight 2800 Kg speed 15 - 115 m/min. infinitely variable cutting surface 0° 350 / 350x350 mm cutting surface 45° right cutting surface 45° left cutting surface 60° right cutting surface 60° left Description: Automatic hydraulic band saw machine in two-column design for 0° cuts on solid material and profiles made of steel, stainless steel and steel alloys up to a maximum of 350x350 mm. Numerically controlled band saw machine which can also be operated semi-automatically, with the new MEP 50 Windows 2 "CE" based control system, specially developed by MEP for automatic machines. The standard equipment includes: Driven chip conveyor, installable on the right or left side of the machine. Bodpfx Asi Hmcdogzolb Clamping pressure regulation of the vices. Feeder with vertical rollers for lateral material support. Clamping pressure regulation. 100 programs can be stored. The machine is available with 34 or 41 belt - without extra charge.

Condition: new, cutting diameter 250 mm saw band length 2950 x 27 x 0,9 mm table height ca. 800 mm band speed 36/72 m/min total power requirement 1,5/1,8 kW weight of the machine ca. 0,37 t dimensions of the machine ca. m MEP sawing machine: Saw band bow, vice unit and base made of durable cast iron Precision grade marking on the cast iron structure Electrical system (with fully identifiable electrical wiring and Low voltage system 24 V) Switch handle IP 55 for manual cycles (if available) Rotating scraper brush for the saw band Clamping unit with vice for quick approach Accurate stops with adjustment for miter cuts at 0°, 45°, 60° left Bi-metal saw band 2950 x 27 x 0.9 mm Keys, instructions for use and instructions for ordering spare parts in the User language SHARK 281 with manual operation and SHARK 281 CCS with manual operation and cutting with automatic head feed by its own weight. CCS (Cut Control System) with (A switch for manual and automatic Cutting – B) Cutting speed regulation – C) Hydraulic brake with tank – D) End stop for stopping the belt) also optional for already produced machines available. Vice with quick adjustment Hydraulic converter for belt tension display Electric coolant pump for cooling and lubricating the saw band and manageable coolant tray above the base frame In the versions with a pneumatic vice (MA), the opening takes place and Closing the vise with a manual valve (with pedal control as option available) Bledpefg E H Iefx Agzeb

Condition: new, MEP COBRA 352 SX evo [Semi-automatic] Article number CB352SX motor power 1,5/2,2 kW belt opening 180 mm belt dimensions 350x32x3,4 Weight 285 Kg Speed 1700/3400 1/min. Cutting surface 0° 120 / 105 / 180x70 Cutting surface 45° right 120 / 100 / 135x60 Cutting surface 45° left Cutting surface 60° right Cutting surface 60° left Description Semi-automatic circular saw for sawing of solid and hollow aluminum materials and light alloys with electro-welded carbide tooth wheel. Basic equipment: -Machine for miter cuts from 45° right to 45° left. -Alignment along the vertical gives the possibility of sawing operations with head inclined between 0° and 45° left. -* MEP represents the latest generation of controls designed for semi-automatic machines with single axis microprocessors. Blsdpfx Ajchkv Iegzeb -CHARACTERISTICS: At the start of the cycle: - Vise closes and motor starts - Saw head lowers for cut - Motor stops - Saw head raises - Vise opens. -New - Display with 16 characters x 2 lines for displaying the following technical parameters: + number of executed cuts + cutting time + ammeter + display of over 100 diagnostic messages and warnings. -New - Display and entry of the alarm and error messages with the possibility of displaying the incidents that have occurred. Electrical equipment: -New - Low voltage control panel: membrane polyester keypad with thermoformed and highlighted push buttons and actuation control signal. -Saw blade stroke programmable directly from the control panel, to adapt to the cutting material. -Ball bearing mounted rotary table to ensure easy and accurate rotation. -Clamping system consisting of two face vices that can be freely arranged along the longitudinal axis of the parts. -Adjustable mechanical stops for quick positioning of the head in the angular positions at 0° and 45° right and left. -Swarf extractor with preparation for OPTIONAL extraction system. -Automatic saw blade lubrication system, operating only at the start of the cut. -Machine is supplied without saw blade. -Preparation for the installation of the minimal lubrication kit of the saw blade (OPTIONAL), besides the conventional standard lubrication with emulsion oil. -Tool and instruction manual with spare parts list. For further technical data, please refer to the attached PDF document. Catalog 2nd page !

Condition: new, 355 mm 350 x 350 mm saw band length 4640 x 34 x 1,1 mm band speed 15 - 115 m/min total power requirement 5,5 kW weight of the machine ca. 2,8 t dimensions 3,2 x 2,2 x 2,7 m Automatic electromechanical band saw machine in two-column design for 0° Cuts on solid material and profiles made of steel, stainless steel and Steel alloys up to a maximum of 350x350 mm. The standard equipment includes: Powered chip conveyor, to be mounted on the right or left of the machine. Clamping pressure regulation of the vices. Bedpfxsfm T Hbj Agzolb Feeder with vertical rollers for lateral material support. Sensors for initial material detection. Clamping pressure regulation. 300 programs can be saved. The machine is available with a 34 or 41 band - at no extra charge. Price on request.

Condition: new, MEP SHARK 332-1 CCS metal band saw with semi-automatic lowering. MEP authorized dealer - please send us your inquiry! Motor power 1.5/1.8 kW Bench opening 335 mm Blade dimensions 3650 x 27 x 0.9 mm Weight 640 kg Speed 40/80 m/min. Cutting area 0° 300 / 260x260 / 330x260 Cutting area 45° right 260 / 250x250 / 270x200 Bledpfx Ajcgbt Regzob Cutting area 45° left 200 / 180x180 / 200x160 Cutting area 60° right 180 / 170x170 / 170x170 Cutting area 60° left Description of the MEP sawing machine: Functioning in CCS version: After the material has been advanced and the vices have been closed, the cutting process begins. The lowering is controlled by the saw's own weight, balanced by a spring and regulated by a hydraulic brake cylinder. Once the cut is complete, the saw arm is manually raised to the required position for feeding the material. Electrical control panel (marked cable connections, operational readiness indicator light, main safety switch provided with padlock, switch or speed selector, emergency stop, thermal magnet protection, 24-volt low-voltage system) Electronic blade tension converter with on-screen display. Manual vice with quick-lock mechanism Base frame with coolant tray and chip drawer, which can be replaced with a motorized chip conveyor (accessory). Electric coolant pump for cooling and lubricating the saw blade. Chip removal brush Adjustable precision stops for making cuts of consistent length. The machine is designed for pallet truck transport. Bimetal saw blade for solid and profile material Tools and operating instructions Motor 1.5/1.8 kW 2 speeds 40/80 m/min. Vice opening 335 mm Saw blade 3650 x 27 x 0.9 Weight 640 kg See image for cutting data For further technical data, please refer to the attached PDF document.

Condition: new, 355 mm 350 x 350 mm saw band length 4640 x 34 x 1,1 mm table height mm band speed 15 - 115 m/min total power requirement 4,0 kW weight of the machine ca. 2,8 t dimensions 3,1 x 2,2 x 2,2 m Shark 350 NC HS 5.0, automatic hydraulic band saw machine in two Column construction for 0° cuts on solid material and steel profiles, Stainless steel and steel alloys up to a maximum of 350x350 mm. The standard equipment includes: + Powered chip conveyor, can be installed on the right or left of the machine. + Clamping pressure regulation of the vices. + Feeder with vertical rollers for lateral material support. + Numerically controlled band saw machines, which are also operated semi- automatically can be done with the new MEP 50, especially from MEP for automatic Bedpfofg E Hzex Agzelb Machine developed, Windows “CE” based control. + Cutting cycle “clean cut” The feeder pushes the workpiece at the back to avoid scoring on the cutting surface when the tape moves up again at the end of the cut. + Fieldbus communication system with double microprocessor and serial Connection. + The user interface with 7” touch screen display and mechanical Buttons are used to ensure the operating functions of the sawing machine reliable, simple and intuitive use, as well as a Real-time control of all cutting parameters

Condition: new, saw blade diameter 350 mm capacity 90 degrees: round 115 mm capacity 90 degrees: square 95 mm 180 x 95 mm Working height 925 mm saw blade turning speeds 15+30+45+90 U/min total power requirement 1,8/2,5 kW weight of the machine ca. 0,41 t dimensions of the machine ca. 0,8 x 1,0 x 1,85 m Electro-pneumatic - semi-automatic vertical circular saw with micro Processor control for miter cuts from 60° left to 45° right. With Linear guide of the saw head. •new system with head sliding vertically on linear guides Upstream slide rails with recirculating balls. •Double gear set for high transmission performance •4 speeds 15/30/45/90 rpm •Vice opening 190 mm Blsdpfx Agsfg Rlbozsb • Stroke of the saw head can be programmed directly from the control panel for adjustment to the cutting material •Pneumatic vertical vice •Saw blade HSS DMO 5 Æ 350x32x2.5 for solid and profile material •Vise with counter-clamping device for double workpiece clamping •Base with removable coolant tray •Chip clearing brush •Length stop for cuts of the same length •Material support arm, at the same time connection option for roller conveyor/ loading side •Turntable with additional central axis

Condition: used, Year of construction: 2009, functionality: fully functional, For sale is a used, fully functional semi-automatic miter band saw. 0° 330 mm 320 mm 450 x 320 mm + 45° 320 mm 300 mm 300 x 300 mm + 60° 210 mm 200 mm 200 x 200 mm Bedpswigavefx Agzolb - 45° 320 mm 300 mm 300 x 300 mm - 60° 210 mm 200 mm 200 x 200 mm Max. vise opening 455 mm Blade size 4500 x 34 x 1.1 mm Saw blade motor power 4.0 kW - three-phase Blade speed 15 - 100 m/min Accessories: 4.5 m roller conveyor, various saw blades

Condition: good (used), Radial fan, chip extraction fan, fan, extraction, dust extraction system, chip blower, extraction system Bedpfjh Szarsx Agzelb -Manufacturer: MEP, extraction system with transport frame -Type: unfortunately without type designation -Motor: Cantoni 0.75 kW / 2840 rpm -Base: on wheels -Dimensions: 950/480/H1860 mm -Weight: 40 kg

Year of construction: 2002, condition: good (used), MEP CONDOR 90 CNC MR automatic disc cutting machine for aluminum profiles with control, feed . Blodpsikztpofx Agzjb Used in very good condition

Condition: new, saw blade diameter 350 x 32 mm capacity degrees: round 1 mm capacity degrees: square 95 x 95 mm capacity degrees: flat 180 x 95 mm capacity degrees: round 110 mm capacity degrees: square 95 x 95 mm capacity degrees: flat 125 x 95 mm capacity 60 degrees: round .0 mm Bljdpfexaab Sjx Agzjb capacity 60 degrees: square x mm capacity 60 degrees: flat x mm

Year of construction: 2016, condition: used, MEP cutting & bending machine, SYNTAX 28 Single bar: ∅10 - ∅28 mm (#3 - #8) Double bars: up to ∅20 mm (#6) • Bar presence detector • Multifunction feeding: gripper and feed rollers • Dual shears Blsdpfxjxl Avvs Agzeb • Bending pins accordingly to international rules Video disclaimer: This video is the manufacturer's promotional demonstration for the SYNTAX 28 model. It does not show the specific line currently for sale. Single bar: ∅10 - ∅28 mm (#3 - #8) Double bars: Up to ∅20 mm (#6)

Condition: excellent (used), functionality: fully functional, Blade inclination -45° / +45°. Maximum vise opening 180 mm Bsdpfjx Hw Sqjx Agzelb Maximum non-feedable length 385 mm Disc size 350 mm Blade rotation speed 1700 / 3400 rpm - 2 speeds

Condition: like new (used), Year of construction: 2017, Used automatic circular saw for aluminium MEP Cobra 352 nc 5.0 Year of manufacture: 2017 Blade dimensions: 350x32x3.4 mm Blade cutting speed: 1700/3400 rpm Cutting angle: from -45° to +45° Cutting capacity: at 0° – round: 120 mm, square: 105 mm, rectangle: 180x70 mm Touchscreen Bjdpfxewu Tz Rj Agzjlb Machine weight: 605 kg

Condition: good (used), Cold circular saw, metal circular saw, miter saw, circular saw, sawing system, metal saw Blodpfxjxlzytj Agzob -Manufacturer: MEP, cold circular saw metal circular saw type TRL 300 pivoting on both sides -Engine: Type C 112 M -Power: 2.2 / 3.0 kW -Speed: 720 / 1450 rpm -Saw blade: Ø 315 mm -Cutting area at 90 degrees flat: 110 x 70 mm -Cutting range at 45 degrees: 100 mm -Accessories: incl.2 saw blades, see photos -Dimensions: 1230/630/H1800 mm -Weight: 273 kg

Condition: used, Year of construction: 2000, saw blade diameter 350 mm dimensions of saw-blade 350 x 32 x 2,5 mm cutting diameter 115 mm stroke 100 mm capacity 90 degrees: square 95 mm capacity 90 degrees: flat 180 x 95 mm capacity 45 degrees: round rechts & links 110 mm capacity 45 degrees: square rechts & links 95 mm capacity 45 degrees: flat rechts & links 125 x 95 mm Blodsv Rrruopfx Agzob capacity 60 degrees: round 90 mm capacity 60 degrees: square 80 mm capacity 60 degrees: flat 90 x 95 mm cutting speed 15 / 30 / 45 / 90 m/min total power requirement 2,6 kW weight of the machine ca. 375 kg dimensions of the machine ca. 1000 x 950 x 1800 mm Features: - With miter adjustment 60° left / 45° right - Coolant device - 2 speeds - Machine base - Operating instructions

Condition: used, Straight-Cut Cutting Bench 40, manufactured by MEP Number of bars: - n.1 Ø 40 - n.2 Ø 32 - n.3 Ø 26 - n.4 Ø 20 - n.5 Ø 16 Bedsvtx Eyopfx Agzslb 22 Fy= 600 N/mm - ft= 650 N/mm Minimum cutting length: 800 mm Maximum length: 12.000 mm Measurement tolerance: +/- 1 mm/m Max. speed positioning: 2m/s Measurement evacuation speed: 2,2 m/s Number of compartments: 5 + 5 Minimum cutting length: 800 mm Maximum length: 12.000 mm Measurement tolerance: +/- 1 mm/m Max. speed positioning: 2m/s Measurement evacuation speed: 2,2 m/s Number of compartments: 5 + 5