Used Horizontal Milling Machine for sale (65,726)

Condition: reconditioned (used), Year of construction: 1976, Universal Tool Milling Machine Manufacturer: DECKEL Model: FP 1 Year of manufacture: 1976 – workshop inspected Machine No.: 51720/08 Geometric acceptance with inspection protocol Accessories: - 3-axis digital readout K+C Arbah-M, new - Fixed table 600 x 210 mm (T-slot 12 mm) - Vertical milling head SK 40 with draw thread S 20 x 2 - Coolant system - Operating manual Used as seen, without warranty The machine technically corresponds Itsdpfx Ajyipmwob Tec to the standard at the time of manufacture.

Condition: used, Year of construction: 2019, x-travel 2.000 mm y-travel 820 mm z-travel 720 mm Control Mazatrol Smooth G spindle taper SK 40 spindle turning speed range 35 - 12.000 U/min spindle motor 22 kW distance spindle centre table top edge 140 - 860 mm table load 1700 Kg rapid travel x/y/z 50 m/min table width 820 mm table length 2500 mm table height over floor 870 mm T-slots 7 T-slot - width 18 mm T-slot - distance 100 mm tool change unit 48 tool changing time 4,7 sec wotkpiece diameter with 2 vacant positions 130 mm workpiece diameter at full load 80 mm max. tool weight 8 kg tool length - max. 350 mm air pressure - required 5 - 9 bar Air volume 260 l/min electrics - voltage/frequency 400 / 50 V/Hz coolant tank 450 l high-performance coolant system 25 bar total power requirement 46,7 kW weight of the machine ca. 14,8 t dimensions of the machine ca. 4,3 x 3,6 x 3,1 m STANDARD ACCESSORIES Transformer for the European market USB port (1 port) Mazak standard colour Spindle speed 12,000 min-1 (steep taper 40) Work area lighting SAFETY DEVICES Operator door with locking switch Work area panelling The splash guard encloses the working area from the side. Fully enclosed work area Protection against chips, coolant and access to the work area during automatic machining. Safety precautions in accordance with global standards COOLANT SUPPLY Coolant supply through spindle (pressure at the pump = 5 bar) Complete coolant system includes pumps, valves, pipework and nozzles for the efficient production of quality components. FACTORY AUTOMATION Automatic switch on/off and warm-up function Automatic switch-on of a warm-up cycle via digital timer MEASUREMENT SYSTEM Tool length measurement and tool breakage detection CHIP DISPOSAL Factory preparation for chip conveyor (left) NUMERICAL CONTROL Fixed control/operating unit Itedpstuggcsfx Ab Tec Relocation Detector Mazatrol SmoothG control unit 19" LCD colour screen (touch screen) Mazak tapping/drilling cycle Tornado (Mazatrol) By drilling and tapping in helical machining mode, a wide range of diameters a wide range of diameters can be machined at high speed with a wide range of diameters can be machined at high speed with just one tool. This function minimises programming and machining times. EIA/ISO input function Tool path check in the background The tool path of a programme can be checked even if another programme number is programme number is called up and processed in automatic mode. 3D coordinate conversion Shape compensation for rotating axes Mazacc 2D software (contour correction) Accuracy is maintained at high feed rates. Mazacc-3D software package for high-speed machining High-speed and high-accuracy machining for contours defined in the finest programme contours defined in the finest programme increments. MAZACC-3D high-speed software package (NO456) is additionally required. Control with high smoothing Interface for LAN SD Memory Card I/F Smooth standard software for M/C - NO443 B) MAZACC-2D software (workpiece shape compensation) - NO444 D) MAZACC-3D high-speed software package - NO445 B) Shape compensation for rotating axes - NO497 D) High accuracy control for finishing operations - Seamless corner point control - Variable acceleration control - Ultra high speed machining mode - NO498 Rapid traverse paths Rounding function Absolute positioning system Machine incl. the f...

Condition: used, Year of construction: 2019, travel -x axis 1.525 mm travel -y axis 770 mm travel -z axis 625 mm control HEIDENHAIN - TNC620 table dimension (L x W) 1.600 x 750 mm numbers of positions in the tool changer 24 tool taper SK50 Milling machining centers - vertical | DOOSAN - MYNX 7500/50 II equipped with 24-way tool changer, ITC cooling system and chip conveyor. Iodpfsyhrbuex Ab Tstc The machine only has 3.165h spindle hours. The machine is in a well-maintained condition. The machine video from the production plant will be shared on request. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: MYNX7500/50II | MYNX 7500 | MYNX7500 | MYNX-7500 | MYNX750050II

Condition: used, Year of construction: 1982, x-travel 300 mm y-travel 160 mm z-travel 340 mm feeds -stepless- 5-500 mm/min rapid traverse 1200 mm/min spindle turning speed range 40 - 2000 U/min tool taper Normkegel 40 table length 600 mm table width 120 mm voltage 380 V frequency 50 Hz rated current 13 A weight of the machine ca. 0,750 t dimensions of the machine ca. 1,8 x 1,5 x 1,8 m Ijdpjvvnfuofx Ab Tetc DESCRIPTION Machine incl: active three-axis digital readout HEIDENHAIN documentation various tool holders Machine vice etc.

Condition: excellent (used), Year of construction: 2019, travel distance X-axis: 450 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 350 mm, feed rate X-axis: 5,000 m/min, feed rate Y-axis: 5,000 m/min, feed rate Z-axis: 5,000 m/min, total height: 2,220 mm, total width: 2,300 mm, total length: 1,990 mm, table width: 400 mm, table length: 800 mm, rotational speed (min.): 5,000 rpm, table load: 300 kg, overall weight: 2,200 kg, Universal milling machine with toolmaker precision  Small-batch production to complex workpieces Vertical milling head with hydraulic tool clamping Y and Z Milling Itedpfx Aboyha Ate Tjc Handwheel in all three axes Linear guideways in all three axes Workspace guard retractable with large chip shield Main motor with spindle brake    X - Travel: 450mm Y - Travel: 400mm Z - Travel: 350mm Table Length: 800mm Table Width: 400mm Table load: 300 Feed rate X-Axis:5000mm/min. Feed rate Y-Axis:5000mm/min. Feed rate Z-Axis:5000mm/min. Spindle Taper: 40ISO/Bt/Mk Power on spindle:10kW Speeds / ranges:5000Rpm Length: 1990mm Width: 2300mm Height: 2220mm Weight: 2200kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), CATALOG NUMBER: 6607 TECHNICAL DATA Circular saw: - Maximum blade diameter: 350mm - Spindle: 30mm - Lockable spindle - Blade adjustable front/back, up/down - Blade guard - Motor: 1.1kW - Extraction port diameter: 80mm Spindle moulder: Tenoning spindle: - Spindle diameter: 40mm - Spindle working height: 140mm - Lockable spindle - Maximum cutter head diameter: 350mm Itsdpfxjyitz So Ab Tsc - 2 spindle speeds: 3000 / 4500 rpm - Motor: 5.5kW - Brake - Side sliding table – manual feed - Table dimensions (L/W): 1180x600mm - Mitre fence - 2 pneumatic clamps - Extraction port diameter: 120mm - Overall dimensions (L/W/H): 2600 (for shipment 2000) /1600/1450mm - Weight: 735kg – Very good condition – Used tenoning machine Net price: 13,900 PLN Net price: 3,300 euros depending on exchange rate 4.2 euro (Prices may vary in case of significant fluctuations)

Condition: excellent (used), operating hours: 8,064 h, Brand : LAGUN Model : GBM-22E Type : CNC 5 EJES Cnc :HEINDENHAIN 530 Table dimensions : 2.200 x 1000 mm Number and width of T slot: 7 x 22 mm Distance between T slots: 140 mm Axis travels (X,Y,Z) : 2.000 x 1.200 x 1.000 mm Itjdpfxeyg R Abs Ab Toc Head type : Automático Spindle speed : 4.000 rpm Taper : ISO 50 DIN 2080 Main motor : 28 kw Continuusly variable speeds : 50➗ 4.000 Speed range : 2 Rapid traverse : 10.000 mm/min Machine weight : 15 tn Electronic hand-wheel : Yes Working hours : Machine running: 22.924 h Control on : 23.132 h Automatic cycle: 8.064 h

Condition: good (used), Year of construction: 2000, machine/vehicle number: 7853, travel distance X-axis: 5,000 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 2,000 mm, table length: 6,000 mm, table width: 2,000 mm, table load: 17,000 kg, Travelling column milling machine | FPT Sirio-M50 - Heidenhain control system - 60-position automatic tool changer - Coolant treatment and filtration unit - Chip conveyor - Cooling unit, manufacturer Deerosdassi (Italy) - Electrical cabinet - Full machine enclosure (protective housing) Iodpfjxzzlhox Ab Totc An inspection is possible at any time by appointment.

Condition: used, Technical details: x-travel: 800 mm y-travel: 800 mm z-travel: 800 mm turning speeds: 35-10.000 1/min spindle: 37 / 30 kW max. torque on the spindle: 525 / 206 Nm Tool bore: BT 50 rapid traverse: 60 m/min tool change unit: 160 Pos. size of pallet: 500 X 500 mm control: MAZATROL 640M Nexus c-axis: 0,001° x 360.000 workpiece weight: 1.000 kg workpiece height max.: 1.000 mm interference area: 900 mm Itjdpewix Hhofx Ab Tsc 2 pcs. horizontal machining centers (HCN 6000-II + HCN 6000, 2005), interlinked with pallet pool (16 pallets) MAZAK FMS, 2 pallet changer, chipconveyor, coolant device with internal coolant supply, *

Condition: used, Technical details: x-travel: 800 mm y-travel: 800 mm z-travel: 800 mm turning speeds: 35-10.000 1/min spindle: 37 / 30 kW max. torque on the spindle: 525 / 206 Nm Tool bore: BT 50 rapid traverse: 60 m/min tool change unit: 160 Pos. size of pallet: 500 X 500 mm control: MAZATROL 640M Nexus c-axis: 0,001° x 360.000 workpiece weight: 1.000 kg workpiece height max.: 1.000 mm interference area: 900 mm 2 pcs. horizontal machining centers (HCN 6000 + HCN 6000-II, 2008), interlinked with pallet pool (16 pallets) MAZAK FMS, 2 pallet changer, chipconveyor, coolant device with internal coolant supply, Iedpfxewix E Rs Ab Tetc *

Condition: excellent (used), Available: Immediately Itsdpfjyh E A Aox Ab Toc

Condition: like new (used), Year of construction: 2020, Console milling machine Reckermann 1300 Kombi The machine is in absolutely mint condition. The customer did not receive the parts for which the machine was intended. Itedpfx Abjx A Etfe Tec

Condition: used, Year of construction: 2001, Technical details: x-travel: 600 mm y-travel: 580 mm z-travel: 580 mm numbers of pallets: 2 pallet size:: 400 x 400 mm max. workpiece weight: 400 kg spindle taper ISO: 40 spindle speeds:: 35 - 12000 Itodowv Tmvspfx Ab Toc feed speeds: 1 - 50000 mm/min rapid speed: 50 m/min total power requirement: 25 kW weight of the machine ca.: 12 t dimensions of the machine ca.: 3,6 x 3,6 x 2,9 m with CNC SEICOS 16 M ( FANUC base ) autom. toolchanger 61-pockets pallet indexing 1° chip conveyor and coolant attachment exhauster clamping cube and diverse toolholders *

Condition: excellent (used), Year of construction: 2014, operating hours: 39,000 h, functionality: fully functional, machine/vehicle number: 3325, Model S-191FTL-PRM Ø 50 mm Axis travel Milling vertical axis Z = 200 mm Milling transverse axis Y = 200 mm Milling longitudinal axis X = 410 mm Power / Thrust Z-Y 2.5 kW / 550 daN X 4.5 kW / > 550 daN X-Y-Z Traversing speed: 40 m/min Acceleration: 10 m/s² Resolution X-Y-Z: 0.0001 mm Measuring system: glass scale MAIN SPINDLE C (Horizontal turning axis) Power: 15 kW Torque / peak: 22 / 28 Nm Measuring system: direct Resolution: 0.0001° Accuracy: 0.001° Bar capacity: Ø 32 mm (option 50 mm) Turning spindle speed: 72,000°/min Clamping force, turning: 4,900 N at 6 bar B-AXIS SPINDLE INCLINATION (machining) Power: 4.3 kW Torque: 119 / 226 Nm Angular travel: -25° / +115° Measuring system: direct Resolution: 0.0001° Accuracy: 0.001° Rotational speed: 36,000°/min Locking torque: 200 Nm MACHINING SPINDLE Power: 8 kW Torque: S1 = 9.5 Nm / S6 = 11.5 Nm Max speed: 30,000 min-1 (option 40,000 min-1) Tool clamping force: 1,000 N Locking torque: mechanical locking with straight toothing Tool holder taper: HSK-40 (A or E) Ijdpfx Abjw T Sl Ds Tetc Through-spindle lubrication: 30 to 100 bar (optional) TOOL CHANGER Number of tools: 30 (option 60) Number of indexed tools: all Tool change time: 1.2 sec. Chip-to-chip time: 4.4 sec. Max tool diameter: Ø 40 mm (80 mm if adjacent station empty) Max tool length: 130 mm Max tool weight: 1.5 kg MISCELLANEOUS Installed power: 25 kVA Operating voltage: 3/N/PE/400V/230V 50 Hz Pneumatics: 6 bar (dry air) CNC CONTROL: Fanuc 31i Screen: 15'' color Keyboard: alphanumeric Control panel features: - 1 key switch for functions - 1 feedrate potentiometer 0–120% - 1 spindle speed potentiometer 50–120% - 1 quick-selection button for machine functions - 1 integrated electronic handwheel CNC Options - Data server with ATA Flash, 1GB memory capacity - J947 1 MB RAM memory - S677 TCPC (tool center point control for 5-axis machining) - S808 Al nano HPCC (Al high precision contour control II) - J930 tool tip radius compensation - J893 coordinate system rotation - J819 Helix (cylindrical) interpolation - J953 memory capacity for 1,000 programs - J828 tapping without compensation chuck - S615 insertion of radii and chamfers - J894 workpiece coordinate system - S993 part setup error - R522 inclined machining plane control with guidance Interfaces - Bumotec-specific programming to minimize collisions - Simplified tool management to prevent input errors - Tool management by threshold value, change according to part count or tool life - Automatic tool setting on machine for easier tool handling - Part counter and production management Y-AXIS (horizontal cross milling axis) Travel: 200 mm Power / thrust: 4.8 kW / 240 daN Resolution: 0.0001 mm Max travel, V1: 50 m/min Max travel, V2: 20 m/min Measuring system: glass scale Z-AXIS (horizontal longitudinal milling axis) Travel: 400 mm Resolution: 0.0001 mm Max travel, V1: 50 m/min Max travel, V2: 20 m/min Measuring system: glass scale Includes 8kW cooling unit Emergency braking system integrated Subject to errors and omissions, technical specifications are provided without obligation.

Condition: excellent (used), Year of construction: 2010, feed length X-axis: 650 mm, feed length Y-axis: 500 mm, feed length Z-axis: 475 mm, feed rate X-axis: 6,000 m/min, feed rate Y-axis: 6,000 m/min, feed rate Z-axis: 6,000 m/min, table width: 450 mm, table length: 1,530 mm, X-Axis: 650mm Y-Axis: 500mm Z-Axis: 475mm Table Length: 1530mm Table Width: 450mm Table load: 350 Spindle speeds: 55 - 4000Rpm Feed rate X-Axis:6000mm/min. Feed rate Y-Axis:6000mm/min. Ijdjxtmqtspfx Ab Totc Feed rate Z-Axis:3000mm/min. Length: 2300mm Width: 2550mm Height: 2200mm Weight: 2850kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 2005, travel distance X-axis: 560 mm, travel distance Y-axis: 320 mm, travel distance Z-axis: 400 mm, feed rate X-axis: 2,400 m/min, feed rate Y-axis: 2,400 m/min, feed rate Z-axis: 2,400 m/min, table width: 450 mm, table length: 950 mm, Fixed table 950 x 450 mm Feeds all direction Itodjxdltbjpfx Ab Tjc ISO-40 and 3kW 3 Axis Digital Read Out Systsem CE-Safety  Coolant system with semi closed lower base  X-Axis: 560mm Y-Axis: 320mm Z-Axis: 400mm Table Length: 950mm Table Width: 450mm Table load: 350 Spindle speeds: 2240Rpm Feed rate X-Axis:2400mm/min. Feed rate Y-Axis:2400mm/min. Feed rate Z-Axis:2400mm/min. Stroke pinole: 0 - 95mm Length: 1800mm Width: 1600mm Height: 1900mm Weight: 1700kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2000, Machine-Details: Stock-No. 1022-2416 Type of machine Tool Room Milling Machine - Universal Make DECKEL Type FP 1 Year of manufacture 2000 Type of control conventional Storage location Monheim (Germany) Country of origin Germany Delivery time Immediately Freight basis Ex warehouse, loaded on truck Technical details: x-travel 300 mm y-travel 160 mm z-travel 290 mm table surface area 600 x 210 mm tool taper SK 40 spindle turning speed range (16) 40 - 2000 U/min feeds -stepless- 5 - 500 mm/min rapid traverse 1,2 m/min spindle motor 1,5 / 1,9 kW Itedpfx Aboyhdbmo Tjc total power requirement 9,5 kVA weight of the machine ca. 830 kg dimensions of the machine ca. 2000 x 2200 x 1655 mm Additional information: The machine is in very good condition and comes from a training workshop. Equipment: * 3-axis positioning control with active digital display Heidenhain TNC 123 - Manual mode: Manual operation and positioning with manual input - Automatic mode: Single-block programme run, programme storage * Fixed angle table * Movable vertical milling head, swivel range +/- 90 degr., quill stroke 60 mm * Coolant equipment * Central lubrication * Tailstock with counter bearing * Manual

Condition: excellent (used), Year of construction: 2009, Machine-Details: Stock-No. 1022-2352 Type of machine Gear Hobbing Machine - Horizontal Make MONNIER & ZAHNER Type KOEPFER MZ 120 Year of manufacture 2009 Type of control CNC Storage location Monheim (Germany) Country of origin Switzerland Delivery time Immediately Freight basis Ex warehouse, loaded on truck Technical details: max. wheel diameter 2-45 mm gear width 250 mm max. module 1,5 mm min. module 0,5 mm Control Fanuc 18i-MB weight of the machine ca. 2,2 t dimensions of the machine ca. 2100 x 1440 x 1700 m Additional information: The combined CNC gear hobbing and worm milling machine KOEPFER MZ 120 is characterized by its flexible usability and is used in the small module area. Just by swiveling the milling spindle from the horizontal to the vertical position and selecting the corresponding operating mode of the CNC control, the worm milling machine becomes a gear hobbing machine and vice versa. CNC control Fanuc 18i-MB (Dialog/ISO) CNC axes = X-axis plunge axis Z-axis longitudinal axis C-axis workpiece spindle B-axis tool spindle V-axis loader axis longitudinal A-axis swivel axis tool spindle head (included as an option) Y-axis shift axis (included as an option) With the following production programs: Worm milling Hobbing Iodpfx Absyhc Dao Tjtc Worm hobbing Bevel gear and spur gear milling Bevel gear hobbing Milling cycles = straight, oblique, crowned toothing, radial, radial-axial, co- and counter-rotating milling, roughing, finishing, worm gears, straight-toothed bevel gears, face gearing (option only in the partial process) Worms [Equipment] Coolant tank 300 liters KF with LNS Turbo MS 250 Chip conveyor, built in 2021!!! Kraft and Bauer fire extinguishing system Spiral conveyor Machine documentation [Technical data] Workpieces: Workpiece diameter 2-45 mm Max. workpiece length 250 mm Tooth length 150 mm Max. module in steel= 1 mm (gear hobbing) 1.5 mm (worm milling) 0.5 mm (bevel gear hobbing) Tools: Cutter diameter= 16-32 mm (gear hobbing) 40-63 mm (worm milling) Machine: Max. setting angle of milling head= +/- 45° (gear hobbing) +/- 30° (worm milling) Shift travel= 34 mm (manual adjustment) 34 mm (CNC axis) Collet/retraction mandrel W 20 Max. speed of workpiece spindle 770 rpm. Milling spindle drive 0.55 kW Max. milling spindle speed 8000 rpm Axis drives = X-axis (plunging) / travel 80 mm via CNC Z-axis (longitudinal feed) / travel 190 mm via CNC C-axis (workpiece axis) via CNC Rapid traverse = X-axis 6000 mm/min. Z-axis 6000 mm/min. Hydraulic unit 0.37 kW

Condition: good (used), Year of construction: 2008, Machine-Details: Stock-No. 1022-E06336 Type of machine Surface Grinding Machine - Horizontal Make ABA / Z & B Type MULTILINE 2507 CNC Year of manufacture 2008 Type of control CNC Storage location Germany Country of origin Germany Delivery time Short-dated Freight basis Ex site, without dismantling and loading Technical details: grinding length 2000 mm grinding width 850 mm distance spindle center to table 900 mm control Siemens 840 D total power requirement 155 kVA weight of the machine ca. 15 t dimensions of the machine ca. 8815 x 4185 x 2963 mm Additional information: Iedpfsyhcwtsx Ab Tstc CNC Precision Surface and Profile Grinding Machine Technical Specifications: Grinding length 2000 mm Grinding width 850 mm Travel, transverse 750 mm Distance from table to spindle center 900 mm (or 800 mm with intermediate plate) Magnetic plate size 2000 x 700 mm Table load without magnet 3500 kg Table speed 60 m/min. Spindle drive 26 kW Grinding wheel dimensions 500 x 150 x 203.2 mm Grinding wheel peripheral speed 35 m/s Equipment: 3-axis contouring control Siemens 840 D Grinding programs: Full-cut grinding Face grinding Plunge grinding Path grinding X/Y-axis and Y-Z-axis Profile grinding Automatic program sequence with roughing, finishing, fine finishing and spark-out grinding. Multiple plunge grinding for economical production Surface grinding with continuous, continuously programmable cross feed Grinding wheel calibration Plunge/step grinding Face grinding Dressing in the grinding cycle with lift-off amount Fully automatic compensation of dressing amounts Tool management AC servo drives with ball screw and absolute measuring system in the X, Y, and Z axes Preloaded precision roller guides in the X, Y, and Z axes with linear guides Portable electronic handwheel Automatic belt filter system Coolant heating Electro-permanent magnetic chuck Fully enclosed Direct measuring system in the vertical axis Temperature-controlled machine bed for consistent accuracy Linear motor in the X-axis, table speed max. 60 m/min. Swiveling control panel Continuous speed control of the grinding spindle Electrical linear measuring device for cross-travel adjustment with zero point setting in any position, resolution 0.001 mm Electro-mechanical locking via position control of the headstock in the cross direction for profile and plunge grinding Mechanical extraction of coolant mist TAG table dresser Pre-profiling dresser VPG 190 Diamond grinding wheel, 190 mm diameter Software program for pre-profiling dresser VPG Rough profiling (roughing) CNC table profile dresser TAD 190 Profile depth max. 45 mm Contour accuracy +/- 0.0025 mm Swivel angle +/- 65 degrees Max. dressing speed 210 mm/min. Diamond wheel for table dressing machine TAD 190 Regrinding package for diamond wheel Intermediate plate for raising the magnet WinWop profiling software Import of CAD profile data SP 60 JOB Listing expansion package Additional holes for the magnet clamping plate to facilitate removal of workpieces using compressed air Ghost shift circuit for shutting down the machine after the end of the program

Condition: new, neu ca. 4 Wochen ab Auftragse Italien 20960 € 402.43 € 40 to 250 mm Iodpfx Ajxh Rulsb Tstc 200 x 20 mm 1100 x 620 mm 55 mm 4,7 - 9,1 mm/s 45 mm/s 45 l 3 kW 950 mm 1250 mm 900 mm 1000 mm 750 kg 2 holder pins, height 110 mm (higher ones on request) Manual stop 500 mm with millimeter scale Adjustable speed 2 handwheels for adjusting the stroke and retraction point Precise hydraulic stroke adjustment, even under pressure Two-hand operation Huge range of tools, prices on request ALTERNATIVE: Version with CNC control

Condition: good (used), Year of construction: 2000, MORI SEIKI SH-503/40 TWIN PALLET CNC HORIZONTAL MILLING MACHINE WITH MORI SEIKI MSX-502III CONTROL UKUK Pallet Dimension 500 x 500mm. Maximum Table Load 1,000kg. Axis Travel X'=630mm, 'Y'=600mm, 'Z'=650mm, 'B'=1° Increment. Rapid Traverse 'X,Y,Z'=32m/min. Spindle Taper BT40. Maximum Spindle Speed 12,000rpm (22kW Motor). 120 Position ATC. Maximum Tool Ø150mm (Without Adjacent Tools), Maximum Length 360mm, Maximum Tool Weight 12kg. S/No. 1212 (2000). DESCRIPTION With Renishaw OMP 600 Spindle Probe, Blum Laser Tool Setting/Breakage Unit, Dual Auger To FSE Chip Conveyor, Through Coolant Filtration System, Oil Chiller, Filtermist Mist Extraction Unit, Handwheel & Signal Tower. Overall Dimensions L4,500 x W2,725 x H3,267mm. Weight 14,900kg. Note: Tooling & Tombstones Not Included. Itsdpsxqt Tijfx Ab Toc

Condition: new, The Servomill® FPK 500 is a state-of-the-art Conventional Vertical Milling Machine from KNUTH, designed for superior performance in toolmaking and mechanical manufacturing. This versatile tool seamlessly integrates modern electronics, making it intuitive and capable of operating with exceptional precision. Its robust construction features a console design made of high-quality grey cast iron, ensuring durability and dimensional stability during operation. Noteworthy attributes include powerful servo feed technology with electronic handwheels, enabling infinite variability in feed speeds and precise control across all axes, accompanied by ball screws that eliminate backlash for enhanced accuracy. With a comprehensive variety of standard equipment such as a coolant system, LED worklight, and an automatic lubrication system, the Servomill addresses operational efficiency while minimizing maintenance needs. Perfect for both skilled operators and training environments, this machine exemplifies the best in modern milling technology. Whether you're looking to enhance your production capabilities or train the next generation of machinists, the Servomill® FPK 500 is an ideal choice. Request a quote today to elevate your milling operations with this advanced Conventional Vertical Milling Machine. Itedpfx Aewa Ah Reb Tjc

Condition: new, The FPK 4.3 is a powerful toolroom milling machine that belongs to the category of Conventional Vertical Milling Machines. This versatile tool-milling machine, renowned in tool and mold making, offers a compact design that combines flexibility with ease of use. The premium cast-iron machine column ensures maximum dynamic rigidity and constant precision, complemented by precision preloaded ball screws on all axes for enhanced performance. Operators will appreciate the ergonomically arranged controls and the swivelling control panel that, alongside the standard digital position indicator, provide maximum comfort. With a large work table measuring 400x800 mm and a travel capacity of 500 mm on the X-axis, the FPK 4.3 is perfect for diverse applications in both training and manufacturing environments. Additionally, it features an automatic feed on all axes with infinitely variable speed settings, and a rigid outer arbor for horizontal milling, making it robust yet precise. Explore the extensive accessory package and take advantage of KNUTH’s reputation for quality – order online today and elevate your workshop with this exceptional milling machine. Ijdeuyh Diepfx Ab Tstc

Condition: excellent (used), CATALOG NUMBER 6056 TECHNICAL DATA - Max workpiece height: 250mm - Spindle working length: 260mm - Spindle diameter: 40mm - Worktable (LxW): 630x360mm - Guide - Motor power: 9.3kW Iodpfx Aeyh Uixob Tetc - 2 pneumatic material clamps - Extraction port diameter: 2x120mm - Air requirement: 8 bar - Dimensions (LxWxH): 1370x980x1620mm - Weight: 450kg – Unpainted – 2 cutters included – Italian-made – Used milling machine, in very good condition Net price: 22,900 PLN Net price: 5,450 EUR Net price calculated at exchange rate of 4.2 PLN/EUR (In case of major exchange rate fluctuations, the price may change)

Condition: like new (used), Year of construction: 2013, functionality: fully functional, Ficep 1201 DE 601 Excalibur drilling machine for processing flat steel and profiles, equipped with a drilling unit that moves longitudinally. This machine has been fully cleaned and inspected. The drilling machine features a numerically controlled drilling unit with longitudinal movement (X-axis), adjustment range 0 - 15,000 mm, and an automatic tool changer with HSK A80 interface for 6 tool positions. Thanks to the 19 kW drill spindle drive, the machine is suitable for use with carbide drilling tools. Technical details: • Support for profiled and flat steel with guide rail and fixed table, total length 15 m • Mobile drilling unit for longitudinal positioning along workpieces • Horizontal drilling head with single drill spindle • Additional tool storage in the X-axis direction • Clamping system for securing materials • Position detection device • Maximum profile size: 1200 x 1200 mm • Number of drill spindles: 1 • Drilling diameter: 5 - 40 mm • Tapping: M6 - M30 • Drill spindle speed: 180 - 3000 rpm • Holder: HSK A 80 • Tool changer: 1 x 6 For more information, please contact us. Itedpfx Aev Iamzob Tec