Used Powder Painting Equipment for sale (43,316)

Condition: used, Year of construction: 2010, functionality: fully functional, Wagner Powder painting equipment for sale! Powder coating device, year 2010 consisting of: Booth: Prima Cube 16000 Powder supply: Powder Center Powder recovery: Cyclon Filter 16000 Movement generator: KHG 350 Production process configurations INCLUDING: I. Presumes Maximum size of parts: LxWxH=2600x400x1850 mm II. Equipment Technological Conveyor automatic speed V=1.2 mtrs/min. Speed regulation between 0.5-2.5 mtrs/min 1. Pretreatment Stand MNA-3-LPG, total size 16,7 mtrs Enter size L=2,5 mtrs a. Washing, degreasing and phosphating; L=3,6 mtrs -number of spray frames – 10 -number of nozzles in frame – 18 -number of nozzles in total – 180 -delivery of the pump – 162 m3/h -power of the pump – 15 kW -vessel 4 m3 for active liquid -inner heat exchanger with LPG burner – 160 kW -temperature 500C -mechanical oil separator - solution filter -the dosing system, membrane pump with regulator Bcodpfx Ageww Adtoleu -washing time – 3 min b. Dripping zone L= 3,1 mtrs -time of dripping – 2 min 30 sec c. First rinsing; L= 1,2 mtrs -number of spray frames – 4 -number of nozzles in frame – 18 -number of nozzles in total – 64 -delivery of pump – 38 m3/h -power of the pump – 3 kW -vessel 1,5 m3 for water -first rinsing time – 1 min c. Dripping zone L= 3,1 mtrs -time of dripping – 2 min 30 sec d. Fine rinsing; L= 1,28 mtrs -number of spray frames – 3 -number of nozzles in frame – 18 -number of nozzles in total – 54 -delivery of pump – 33 m3/h -vessel 1,5 m3 for water -power of the pump – 3 kW -one extra spray frame -number of nozzles in frame – 18 -fine rinsing time – 1 min e. Dripping zone L= 2 mtrs -time of dripping – 1 min 40 sec Three openings to connect to exhaust system with three ventilators Operating space made of stainless steel. Pipes made of PVC or S/S. 1 unit 2. Automatic Dryer after water AST-1-KLPG: - operating space dimensions LxWxH=7000x3000x2800 - air curtains each side to avoid heat losses - one indirect heat exchanger heated with liquid petrol gas to produce 200 kW of rated power - three blowers 6000 m3/h of air delivery - two openings to connect to exhaust system - temperature sensor and temperature regulator - overheating sensor - circulation sensor - operating space made of zinc plated steel - thermal insulation 200 mm thick - drying time 10 min 1 unit 3. Automatic Curing Oven APT-2-KLPG for curing powder paints - operating space dimensions LxWxH=10200x3600x2800 - air curtains on one side to avoid heat losses - two indirect heat exchangers heated with liquid petrol gas to produce 300 kW of rated power, of each - eight circulation blowers, capacity of each 6 000 m3/h - two openings to connect to exhaust system - temperature sensor and temperature regulator - overheating sensor - circulation sensor - operating space made of zinc plated steel - thermal insulation 200 mm thick - curing time 25 min 1 unit 4. An overhead rail conveying system ATR-ADAX, for the paint shop including the following: • straight track with hangers L=400 mm 146 mtrs • drive station 2 pc • tension station 1 pc • chain lubrication station 1 pc • drawing of the track supporting structure 1 set

Condition: new, Year of construction: 2025, functionality: fully functional, Ball Mill with Air Classifier: The Ultimate Powder Processing Equipment In the world of industrial powder production, precision, efficiency, and flexibility are paramount. Whether producing ultra-fine powders for high-tech applications or coarser materials for everyday products, the combination of a Ball Mill with Air Classifier offers unparalleled performance. This dynamic duo provides a comprehensive solution for industries ranging from chemicals and ceramics to paints, plastics, and pharmaceuticals. This article introduces the ball mill with an air classifier, explores its applications, and highlights the key advantages of this essential powder equipment. General Introduction to Ball Mill with Air Classifier ball mill with air classifier is an advanced grinding and classification system designed for efficient, high-quality powder production. The system consists of two main components: 1. Ball Mill: A cylindrical grinding device filled with grinding media (such as steel balls) that operates by rotating around its axis. The raw material is reduced to smaller particle sizes through impact and friction within the mill. 2. Air Classifier: A sophisticated device that separates particles based on size using airflow. Fine particles are carried away, while coarser particles are returned to the ball mill for further grinding. The combination of these two components creates a closed-loop system that ensures consistent particle size distribution, high efficiency, and minimal waste. Applications of Ball Mill with Air Classifier The ball mill with air classifier is a versatile solution used in a wide range of industries to process various materials. Key applications include: 1. Mineral Processing The system is widely used in the production of minerals such as calcium carbonate, quartz, feldspar, and talc. These finely ground minerals are essential for industries like ceramics, paints, plastics, and rubber. 2. Cement and Construction Materials Cement and other construction materials require precise particle size control for optimal performance. The ball mill with air classifier ensures uniformity and enhances the quality of construction materials. 3. Chemicals and Pharmaceuticals Fine powders play a critical role in the chemical and pharmaceutical industries. From active pharmaceutical ingredients (APIs) to industrial chemicals, this system delivers the consistent quality required for these applications. 4. Paints, Coatings, and Pigments The production of paints and coatings demands ultra-fine powders to achieve smooth finishes and vibrant colors. The ball mill with air classifier produces high-quality powders for superior results. #### 5. Food and Agriculture Bcsdpfovlwkxsx Agleu Food-grade powders such as additives, preservatives, and agricultural products like fertilizers can be efficiently processed using this system, meeting stringent regulatory requirements. Industries That Benefit from Ball Mill with Air Classifier Several industries rely on the capabilities of this system to produce fine powders with specific characteristics: - Ceramics: Produces high-purity powders for tiles, insulators, and advanced ceramics. - Rubber and Plastics: Creates fillers and additives for improved durability and performance. - Pharmaceuticals: Ensures consistent particle size for APIs and excipients. -Construction: Delivers materials for concrete, plaster, and other applications.

Condition: new, Year of construction: 2026, 🏭 POWDER COATING BOOTH KPP Automatic filter cleaning with adjustable pulse timing, plus manual mode. 🧼⏱️🖲️ 100% polyester filters - washable, water-resistant, long-lasting. 🧵💧♻️ ROMER JET™ filter cleaning - patented high-speed air pulse for powerful cleaning. 💥💨🏅 Low-noise aluminium fans (74-79 dB) - safer, spark-minimized operation with low power use. 🔇⚡🛡️ Adjustable airflow baffle - antistatic plate protects filters and improves extraction. 🌬️🛡️📈 Bedpfx Agofy T Tbsljcu Leak-tight filter mounting - gasket + clamp for strong sealing and easy service. 🔩🧷✅ Touchscreen control - auto (time), auto (clogging sensor), manual + filter change alerts. 📲🔁⚠️ Optional powder container - waste collection or fluidized tank with direct applicator feed. 🧺💨🎯 Overhead puller - moves beams through the booth, reducing manual effort. 🏗️➡️💪 Integrated sieving unit (with container) - clean recovered powder for reuse, EX-zone vibrator. 🧪♻️⚙️ Explosion-proof design - components selected to prevent explosive mixtures. 🛡️💥✅

Condition: new, Year of construction: 2026, ### 🔫 ProfiGun PM-1 powder gun Lightweight, ergonomic, perfectly balanced with a contoured grip. ✋⚖️ Adjust powder output and switch programs directly on the gun. 🎛️ Ceramic cascade up to 100,000 V for efficient charging of all powder types. ⚡ New-generation nozzles improve penetration on complex parts. 🎯🧩 Profiled nut for a secure grip + conductive handle for excellent operator grounding. 🔩🧤 Impact-resistant materials, fully demountable design, replaceable powder path tube. 🛡️🛠️ Patented in the EU and US. Polarity: negative. 🇪🇺🇺🇸➖ One-piece powder path + quick-release hose coupling reduce leaks and speed up hose changes. 🔌✅ ### 💨 ProfiJector powder pump Efficient injector with an optimized feed angle validated by research. 📐🔬 Lower powder and air consumption vs. right-angle injectors, with low running costs. ♻️📉 European patent protected. 🏅 ### 🖥️ PSS controller - 7" touchscreen 7-inch glove-friendly touch panel. 🧤📲 3 auto programs: overcoating, hard-to-reach areas, flat surfaces. 🔁 Fine tuning: 0.1 kV and 0.1 uA resolution. 🎚️ Advanced pneumatic valves for precise air dosing (patent pending) + real airflow measurement to detect drops or blockages. 💨📈⚠️ Diagnostics, program naming, external control via Modbus. 🧠🔧🔌 ### ⚡ ProfiCharge ceramic cascade (made in Poland) High-precision ceramic cascade up to 100,000 V, manufactured in Poland. 🇵🇱⚡ High-frequency ion emission (up to 17,000/sec) improves charging - less powder to the collector, more on the part. 🎯📉 Ultra-precise current control: 0-100 uA, stable even below 10 uA (0-10 uA focus with 0.1 uA steps). 🎛️ ### 💨 Air and application quality features Electronically controlled needle valves + integrated flowmeters for real-time, precise air delivery. 💨✅ Adjustable electrification curve for different powders and demanding parts. ⚙️🧩 Non-stick, puncture-resistant nozzles resist electrical breakdown, reduce clogging, and simplify color changes. 🧼✨ Automatic gun purge (from handle or screen) for faster, cleaner color changes. 🔁💨 ### 🛡️ Safety and compliance Discharge energy below 2 mJ + antistatic hose with double grounding strap. ⚠️🔒 Bsdpjyfim Ajfx Aglocu ATEX and EN 50050-2 compliant for potentially explosive areas. ✅ ### 🧠 Productivity and support Quick Program: fast switching via rapid trigger presses. ⚡🎛️ Visual wear counters + fault history, suggestions, and self-monitoring diagnostics. 👀🔧 Up to 8 languages: PL, EN, DE, FR, RU, ES, IT, SV. 🌍 Animated troubleshooter for guided diagnostics. 🧭 Professional mode (hints on/off) + daily and job statistics for order management. 📊⏱️✅

Condition: new, Year of construction: 2026, ### 🔫 ProfiGun PM-1 powder gun Lightweight, ergonomic, perfectly balanced with a contoured grip. ✋⚖️ Adjust powder output and switch programs directly on the gun. 🎛️ Ceramic cascade up to 100,000 V for efficient charging of all powder types. ⚡ New-generation nozzles improve penetration on complex parts. 🎯🧩 Profiled nut for a secure grip + conductive handle for excellent operator grounding. 🔩🧤 Impact-resistant materials, fully demountable design, replaceable powder path tube. 🛡️🛠️ Patented in the EU and US. Polarity: negative. 🇪🇺🇺🇸➖ One-piece powder path + quick-release hose coupling reduce leaks and speed up hose changes. 🔌✅ ### 💨 ProfiJector powder pump Efficient injector with an optimized feed angle validated by research. 📐🔬 Lower powder and air consumption vs. right-angle injectors, with low running costs. ♻️📉 European patent protected. 🏅 ### 🖥️ PSS controller - 7" touchscreen 7-inch glove-friendly touch panel. 🧤📲 3 auto programs: overcoating, hard-to-reach areas, flat surfaces. 🔁 Fine tuning: 0.1 kV and 0.1 uA resolution. 🎚️ Advanced pneumatic valves for precise air dosing (patent pending) + real airflow measurement to detect drops or blockages. 💨📈⚠️ Diagnostics, program naming, external control via Modbus. 🧠🔧🔌 ### ⚡ ProfiCharge ceramic cascade (made in Poland) Bcedpfx Aoyfik Ioglsu High-precision ceramic cascade up to 100,000 V, manufactured in Poland. 🇵🇱⚡ High-frequency ion emission (up to 17,000/sec) improves charging - less powder to the collector, more on the part. 🎯📉 Ultra-precise current control: 0-100 uA, stable even below 10 uA (0-10 uA focus with 0.1 uA steps). 🎛️ ### 💨 Air and application quality features Electronically controlled needle valves + integrated flowmeters for real-time, precise air delivery. 💨✅ Adjustable electrification curve for different powders and demanding parts. ⚙️🧩 Non-stick, puncture-resistant nozzles resist electrical breakdown, reduce clogging, and simplify color changes. 🧼✨ Automatic gun purge (from handle or screen) for faster, cleaner color changes. 🔁💨 ### 🛡️ Safety and compliance Discharge energy below 2 mJ + antistatic hose with double grounding strap. ⚠️🔒 ATEX and EN 50050-2 compliant for potentially explosive areas. ✅ ### 🧠 Productivity and support Quick Program: fast switching via rapid trigger presses. ⚡🎛️ Visual wear counters + fault history, suggestions, and self-monitoring diagnostics. 👀🔧 Up to 8 languages: PL, EN, DE, FR, RU, ES, IT, SV. 🌍 Animated troubleshooter for guided diagnostics. 🧭 Professional mode (hints on/off) + daily and job statistics for order management. 📊⏱️✅

Condition: new, Year of construction: 2025, VG1E-VN MANUAL FAST COLOR CHANGE TYPE POWDER COATING SYSTEM The powder coating system is designed for powder coating applications with frequent color changes during the day. The equipment is on a wheeled stand for ease of operation. Powder coating is sucked directly from the powder box, which allows rapid color changes. The powder box is placed on the vibrating table, suction pipe fluidizes the powder coating in the box, ensuring effective mixing, and the powder coating is homogeneously sent to the gun through an injector placed on the suction pipe. TECHNICAL SPECIFICATIONS Input voltage : 220V 50Hz Air need : 350 lt/min Input pressure : 6 bar Vibration motor : 220V 25W Gross weight : 55 Kg VG4 CONTROLLER AND MANUAL POWDER COATING GUN The VM manual powder coating gun is completely dismountable. The ergonomic gun handle design ensures ergonomic handling and does not tire the operator during coating application. The high voltage cascade has a long service life, its tightness prevents contact with dust and minimizes the risks in this area. The well-designed head assembly and nozzle ensure excellent polarization and homogeneous coating on surfaces during application. The electronic touch panel on the back of the gun provides ease of use during operation. The control unit is digital and allows precise adjustment of settings via the touch panel. TECHNICAL SPECIFICATIONS Gun Type : Corona System Polarization : Negative Cascade input voltage: 0-10,5V DC Output voltage : 100 kV Output current : 0 -150 μA Powder output (3,5 bar) 500 g/min Protection class : IP 54 Voltage cable length : 5 m Powder hose length : 5 m Gun weight (gross) : 450 g Operating temperature :-20-50 ° C Nozzle :Flat jet or Ø16-20-24mm deflectör Bodevv N Tyjpfx Agljcu

Condition: new, Year of construction: 2024, ### 🔫 ProfiGun PM-1 powder gun Lightweight, ergonomic, perfectly balanced with a contoured grip. ✋⚖️ Adjust powder output and switch programs directly on the gun. 🎛️ Ceramic cascade up to 100,000 V for efficient charging of all powder types. ⚡ New-generation nozzles improve penetration on complex parts. 🎯🧩 Profiled nut for a secure grip + conductive handle for excellent operator grounding. 🔩🧤 Impact-resistant materials, fully demountable design, replaceable powder path tube. 🛡️🛠️ Patented in the EU and US. Polarity: negative. 🇪🇺🇺🇸➖ One-piece powder path + quick-release hose coupling reduce leaks and speed up hose changes. 🔌✅ ### 💨 ProfiJector powder pump Efficient injector with an optimized feed angle validated by research. 📐🔬 Lower powder and air consumption vs. right-angle injectors, with low running costs. ♻️📉 Bcsdpfx Agsflpi Nslju European patent protected. 🏅 ### 🖥️ PSS controller - 7" touchscreen 7-inch glove-friendly touch panel. 🧤📲 3 auto programs: overcoating, hard-to-reach areas, flat surfaces. 🔁 Fine tuning: 0.1 kV and 0.1 uA resolution. 🎚️ Advanced pneumatic valves for precise air dosing (patent pending) + real airflow measurement to detect drops or blockages. 💨📈⚠️ Diagnostics, program naming, external control via Modbus. 🧠🔧🔌 ### ⚡ ProfiCharge ceramic cascade (made in Poland) High-precision ceramic cascade up to 100,000 V, manufactured in Poland. 🇵🇱⚡ High-frequency ion emission (up to 17,000/sec) improves charging - less powder to the collector, more on the part. 🎯📉 Ultra-precise current control: 0-100 uA, stable even below 10 uA (0-10 uA focus with 0.1 uA steps). 🎛️ ### 💨 Air and application quality features Electronically controlled needle valves + integrated flowmeters for real-time, precise air delivery. 💨✅ Adjustable electrification curve for different powders and demanding parts. ⚙️🧩 Non-stick, puncture-resistant nozzles resist electrical breakdown, reduce clogging, and simplify color changes. 🧼✨ Automatic gun purge (from handle or screen) for faster, cleaner color changes. 🔁💨 ### 🛡️ Safety and compliance Discharge energy below 2 mJ + antistatic hose with double grounding strap. ⚠️🔒 ATEX and EN 50050-2 compliant for potentially explosive areas. ✅ ### 🧠 Productivity and support Quick Program: fast switching via rapid trigger presses. ⚡🎛️ Visual wear counters + fault history, suggestions, and self-monitoring diagnostics. 👀🔧 Up to 8 languages: PL, EN, DE, FR, RU, ES, IT, SV. 🌍 Animated troubleshooter for guided diagnostics. 🧭 Professional mode (hints on/off) + daily and job statistics for order management. 📊⏱️✅

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ Bcsdpfx Agjfz I Rxelju 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ Bcjdpfx Agofz U Nbolju 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 Bedpfx Aoflk Awsglocu 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: used, Year of construction: 2006, functionality: fully functional, machine/vehicle number: 13-3188, total length: 160,000 mm, total height: 3,000 mm, total width: 9,000 mm, temperature: 230 °C, volume flow: 100 m³/h, Powder Coating System ARNO HERING PTR 15-45-SE (Year 2006) For sale is a complete powder coating system from ARNO HERING (model PTR 15-45-SE), manufactured in 05/2006. The system consists of an application booth, drying/curing oven, and crane rail/carrier racks (hanging racks). The system is from ongoing production and is suitable for coating metal parts and assemblies. Highlights / Equipment (Components): - Application booth (powder application) - Drying oven / curing oven - Crane rail / manual overhead conveyor system including carrier/hanging racks - Documentation/control manuals: to be included if available Technical Data (according to nameplate): - Model: PTR 15-45-SE - Year of manufacture: 05/2006 - Machine number: 13-3188 - Max. drying temperature: 230 °C - Minimum exhaust air volume (at 20 °C): 100 m³/h - Max. permitted powder quantity: 10 kg/h Notes: - Inspection on site is possible by appointment. - Loading/dismantling: by arrangement (possibly to be handled by the buyer). - Sale ex location, subject to prior sale. We are offering this used ARNO HERING PTR 15-45-SE powder coating system, year 2006. Model: PTR 15-45-SE Year: May 2006 Machine number: 13-3188 Maximum drying temperature: 230 °C Minimum exhaust air volume at 20°C: 100 m³/h Maximum permitted powder quantity: 10 kg/h Bsdpfx Agex Squ Aslecu If you have any questions or need further information, please feel free to send us a message or call us.

Condition: new, Year of construction: 2025, functionality: fully functional, fuel: electricity, Equipment: lighting, We are offering this new Electron E-Coat +3 Master M powder coating machine, year of construction 2025. The Electron E-Coat+3 Master Series is highly user-friendly, featuring a built-in LED light in the hand gun to ensure optimal visibility of the area to be coated, even in low-light conditions (such as internal coating applications). In addition, it is equipped with a storage capacity of 50 different spraying programs and 4 standard settings, making operation quick and easy for both experienced and inexperienced users. What further distinguishes this unit from the competition are its powerful powder charging capabilities—with a charging capacity of 120 kV-120 µA—and the Hybrid Proportional Valve System that is unaffected by changes in compressed air supply pressure. This enables outstanding results! All this at an excellent price/performance ratio. Bcjdpsx Rcm Iefx Agleu Feel free to contact us for more information. If you have any questions or would like more details, please send us a message or WhatsApp.

Condition: used, Swiss manufacturer GEMA injection powder coating equipment for sale, manufactured in 2002. It consists of: Powder coating manipulators (2pcs of 8 nozzles each) for painting parts up to 1800 mm high; Bjdpfx Agjqlazdslocu Control and programming cabinet for the manipulators; Powder feeding centre; If you have any further questions, we will be happy to answer them.

Year of construction: 1987, condition: used, machine/vehicle number: 29990, Volume flow: 300 cm³ Overpressure: 231 bar Max. volume flow at 25 DH/min: 7.5 l/min Bjdebnpc Uepfx Aglocu Inlet overpressure or required air pressure: 7 bar Air consumption: 9,7 l/DH Weight: 100 kg Space requirement: 1250 x 750 x 1400 mm

Condition: good (used), Spray booth water stabilizer Technical data: Agitator Pump Filling spout Ø 9 cm Thermostat display Level indicator Ø 176cm H: 67 Thickness 3mm More articles - new and used - you will find in our store! Bedpoiu Hwuefx Aglecu International shipping costs on request!

Condition: used, Year of construction: 2015, functionality: fully functional, The Datacolor 500 is a device representing a spectrophotometer that measures, calculates, and expresses color in a precise and objective manner, making it possible for color to be communicated and reproduced accurately. The spectrophotometer can measure a wide range of materials, including synthetic or natural fabrics, liquids, plastics, paper, metal, painted substrates, and, in some cases, multi-colored materials. In industries such as textiles and apparel, spectrophotometers enable companies to define color standards and tolerances, allowing supplier samples to be compared and measured against these standards. Spectrophotometers measure the wavelengths of light absorbed and reflected by a color sample and then quantitatively convert this data into color values that can be interpreted by color management software. Purchased in 2015 from Datacolor AG, Switzerland. Bcedpfxexrypyj Agleu

Condition: like new (used), Year of construction: 2021, functionality: fully functional, total length: 44,860 mm, total height: 5,250 mm, total width: 17,100 mm, type of input current: three-phase, workpiece weight (max.): 80 kg, input frequency: 50 Hz, heating capacity: 350 kW (475.87 HP), compressed air connection: 8 bar, workpiece height (max.): 2,000 mm, workpiece length (max.): 800 mm, clearance between the columns: 3,000 mm, fuel: domestic gas H, insulation material: PUR, insulation thickness: 80 mm, workpiece width (max.): 800 mm, Equipment: cabin, lighting, For sale: application section of a powder coating plant from 2021. Application technology: NORDSON ENCORE HD, charging cascades with voltage up to 100 kV, control system POWDER PILOT, feed center SPECTRUM HD II, ENCORE HD spray guns (16 units) + 2 manual guns, HDLV type pump (18 units). Bedpfx Agewhbnleljcu

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators. Bcsdpfx Ajfz Dubogleu

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Bedpfx Agjfz Apqelocu Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell Bodpfsfz Dt Njx Aglscu The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. Bcsdpfx Asfz I D Dogleu This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Bcedpfxofz I Ede Aglou Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. Bodpsflmdwofx Aglocu The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning. Bodpsfzkrnofx Agljcu

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. Bsdpfx Agsfz Nb Tjljcu The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.