Used Transfluid Db 650 St for sale (16)

Condition: used, functionality: fully functional, Year of construction: 2005, operating hours: 142,500 h, pipe diameter (max.): 50 mm, pipe length (max.): 2,000 mm, bending radius (max.): 150 mm, tube bending machine, SPS bending machine, tube bender, tube bending system, tube processing, tube technology, electro-hydraulic, mandrel bending machine Capacity: - Round tubing mild steel Ø 50 x 3,0 mm - Round tubing stainless steel Ø 50 x 2,0 mm - Max. moment of resistance 5,0 cm³ - bending angle up to 180° + 10° overbend Gksdowzammjpfx Aftof Machine equipment-/basic accessories: - Tube insertion length/usable length 2000 mm - Max. bending radius 150 mm - Bending height 1050 mm - Free-standing bending head, length 850 mm - The free-standing bending head is so compact that tubes can be processed with a clear spacing of 400 mm between two bends - Electrohydraulic drive - With automatic cycle; one of the following modes can be selected via key switch - Function activiation via hand switch - In manual operation mode, all functions can be operated via push button in jog mode - In semi-automatic mode, the tube is clamped after the first activation, bent after the second activation, and then the machine returns to its initial position - Counter bearing opens wide, so that with the corresponding equipment (VWE A-642) the rotation unit can move up to just behind the bending tool - Bending direction counter-clockwise - With hollow shaft to achieve small radii - For radii from 1x tube diameter - Manual tool reset - Automatic tool locking - All functions hydraulic - Operation via push button - Standardized hydraulic components - Stationary machine - Color: RAL 7037 dust grey, RAL 3000 red Machine data: - Nominal pressure: 250 bar, operating pressure: 200 bar - Operating voltage: 400 Volt – 50 Hz – 3 phase – 7.5 kW - Length: 3200 mm - Width: 1400 mm - Height: 1300 mm - Weight: approx. 1470 kg

Condition: ready for operation (used), Year of construction: 2005, Bending direction: clockwise, steel tube diameter: 50mm, steel tube thickness: 3mm, stainless steel tube diameter: 50mm, stainless steel tube thickness: 2mm, max. section modulus: 5cm³, bending angle: 180°+10°, max. tube length: 2000mm, max. radius range: 150mm, bending height: 1050mm, bending head length: 850mm, min. bend spacing: 400mm, nominal pressure: 250bar, operating pressure: 200bar. Machine dimensions X/Y/Z: approx. 3200mm/1400mm/1300mm, weight: approx. 1500kg. Documentation available. An on-site inspection is possible. Gkjdpfx Aexwyw Ieftef

Condition: good (used), Year of construction: 1996, tube diameter 6 - 28 mm wall strength 2 mm bending radius min. 2 x D Control IPU 20 Gksdpfsvtgn Nsx Aftsf bending radius max. 5,0 x D mm bending angle max. 190 ° arbor length 3000 mm operating pressure 180 bar hydraulic motor 4 kW weight of the machine ca. 900 kg dimensions of the machine ca. 3,8 x 1,1 x 1,3 m Semi-automatic electro-hydr. mandrel tube bending machine with PLC control for 20 angles and display in the control panel for bending angle specification, angle detection and angle measurement via absolute value encoder, autom. tool plate reset, Turning device with digital display, hydr. quick chuck, aut. Mandrel lubrication, adjustable length stops. Operating modes: MANUAL and semi-automatic. Control buttons: hydraulics on / off, operating mode selection, clamp to / on, clamp forward / backward, mandrel forward / backward, bending forward / backward /, locking forward / backward, mandrel lubrication, turning device forward / backward, plate reset, length stop forward, emergency stop. The machine comes from a prototype construction and was only used a little until 2000. After that, the machines of this department were sold. However, the purchaser did not use the pipe bending machine and therefore it has only stood in the warehouse and has not worked since then ((original paint). Please notice that the price of a new machine today is over € 60.000,--. Machine dealer with own stock of 1600 m².

Condition: good (used), functionality: fully functional, Year of construction: 1998, bending radius (max.): 600 mm, mandrel length: 1,200 mm, wall thickness: 8 mm, Transfluid DB 40100ST Mandrel bending machine Tube bending machine The above machine is a mandrel bending machine designed exclusively for the production of tubes and profiles with an outer diameter of 40-100 mm, max. 110x5 mm with a max. wall thickness of 8 mm or for the processing of solid materials with an outer diameter of up to 70 mm. Pipe push-on length/usable length: 1200 mm Godsr H Havopfx Aftskf Radius range max:600 mm Bending height:1200 mm Machine data Length:4000 mm Width:2600 mm Height:1400 mm Weight:9000 kg

Condition: good (used), Year of construction: 2008, control type: CNC control, Stainless steel tube diameter: up to 42 x 2.0 mm Steel tube diameter: up to 42 x 3.0 mm Gkodpfx Afsx Eixdstsf Max. bending angle: +/- 180 + 10° Section modulus: 4.1 ccm Operating pressure: 6 bar Total power requirement: 5.5 kW Machine weight approx.: 3 t Space requirement approx.: 6100 x 2300 x 1300 mm

Condition: used, Year of construction: 1997, tube diameter 60 mm wall strength 6 mm bending radius min. 180 mm total power requirement 5,5 kW weight of the machine ca. 1300 t dimensions of the machine ca. 3500 x 1250 x 1300 m Description: Round tube steel (S235): 60.0 x 6.0 mm Round tube stainless steel (S 355): 60.0 x 4.0 mm Gjdpfx Ajt I D Uxsftskf Square tube steel: 50 x 50 x 4.0 mm Rectangular tube steel: 60 x 40 x 2.0 mm max. usable length: 3048 mm Bending speed: 10°/sec including tools (see photos) Mandrel is no longer available, can be retrofitted

Condition: used, Year of construction: 1996, Hydraulic mandrel bending machine with many accessories Preselection of 8 different bending angles with digital display Digital length display and digital display of twist Gjdpeq Daxtefx Aftskf Max. usable length: 6096 mm Round steel tube (S 235): 60.0 x 6.0 mm Round tube stainless steel (S 355): 60.0 x 4.0 mm Square steel tube: 50 x 50 x 4.0 mm Rectangular steel tube: 60 x 40 x 2.0 mm Max. bending angle: 180° Weight: approx. 1800 kg

Condition: used, functionality: fully functional, Year of construction: 1998, machine/vehicle number: 7385, degree of automation: semi-automatic, actuation type: electric, controller manufacturer: Transfluid, controller model: IPU 20, pipe diameter (max.): 648 mm, pipe length (max.): 6,000 mm, tube wall thickness (max.): 3 mm, bending angle (max.): 180 °, bending radius (max.): 125 mm, bending radius (min.): 50 mm, working width: 6,000 mm, mandrel length: 5,500 mm, number of axes: 3, working height: 1,300 mm, table length: 7,000 mm, table width: 900 mm, table height: 1,300 mm, overall weight: 1,000 kg, total length: 7,000 mm, total width: 900 mm, total height: 1,300 mm, power: 5 kW (6.80 HP), input voltage: 400 V, input current: 25 A, input frequency: 50 Hz, type of input current: three-phase, oil tank capacity: 1,320 l, operating pressure: 200 bar, Equipment: documentation/manual, emergency stop, Bending software requires a new update. Bending mandrels are available, bending tools are not included. Gjdpfsxcxupox Aftjkf

Condition: new, functionality: fully functional, Year of construction: 2025, Tube bending machine, CNC bending machine, tube bender, tube bending system, tube processing, tube technology, right-left bending, 3D tube bending, servo-electric, multi-axis bending machine, mandrel bending machine Capacity: -Round tubing mild steel S235 22 x 2,0 mm Ø -Round tubing stainless steel 1.4571 22 x 1,5 mm Ø -Max. moment of resitance 0,5 cm³ (S235) -Bending angle up to 180° + 10° spring back -Speed of bending axis max. 300°/sec. -Speed of front feed axis max. 1800 mm/sec. -Speed of rotation axis max. 600°/sec. Gedewvqgtepfx Aftskf -Repetition tolerance bending +/- 0,05° -Repetition tolerance length +/- 0,05 mm -Repetition tolerance rotation +/- 0,05° -Radius max. 66 mm -Bending height 1150 mm -Boosting force length positioning 2,5 kN -Power bending axis servo-electric -Automatic positioning rotation/ length servo-electric -All other axes servo-electric (e.g. clamping, mandrel forwards/ backwards, etc.) -Positioning of the bending heads servo-electric -Positioning of the pressure die (radial) servo-electric -Pressure die movement (axial) servo-electric -Material clamping (chuck) pneumatic Machine equipment-/basic accessories: -Bending head for bending right-hand and left-hand with one off set bend device -Bending head can be positioned horizontal and vertical, including rotation axis for change of bending direction (right- or left-hand) -Positioning of bending head via combined diagonal and rotation axis, this allows bending right- and left-hand in one operation -Bending direction free programmable, changing right-/left-hand for one tube geometry -Each bending head can be equipped with minimum two tool sets, e.g. with different bending radii or form-clamps, max. changing height for standard machine is 50 mm -Max. difference of bending radii for each bending level 1,5xD -With hollow shaft for using tooling for small radii -Minimum clamping length on the tube end, because of wide opening pressure die which allows the off set bend device to move directly behind the bending tool -Chuck for use of segment collets Depending on the contour of the clamping segments, already formed tube ends can be clamped -Material clamping in the VWE pneumatic -Footswitch to open or close the collet in the offset bend device, for easy loading and unloading -Following pressure die for bends up to 180° (for radii up to max. 2xD, for lager bending radii the pressure die can be repositioned to ensure a constant contact up to 180° bending angle) -For a correct positioning of the mandrel the machine is equipped with a mandrel support -Automatic, programmable mandrel withdrawal -Minimum quantity lubrication for automatic mandrel lubrication, adjustable lubricant quantity, can be used from inner tube Ø 13.5 mm -Central lubrication for automaticall lubrication of all moving parts in the necessary cycle -Air conditioning for the electrical carbinet -Starting of operation via manual switch on the control panel -In manual mode, all functions can be operated by keyboard and mouse The machine is built according to the latest safety regulations -In order to comply with the CE guidelines, a safety barrier is required in addition (DB-SA...) -Colour RAL 7047 grey, RAL 3020 red Control description: -Control via Simatic PC IPC BX-32A, Xeon W-11155MLE

Condition: refurbished (used), functionality: limited functionality, Year of construction: 2003, operating hours: 24,000 h, pipe diameter (max.): 100 mm, pipe length (max.): 4,100 mm, bending angle (max.): 183 °, bending radius (max.): 300 mm, wall thickness: 8 mm, Transfluid DB 2090 DB CNC Mandrel Tube Bending Machine. Excellent High Quality Germany Machine, with fully refurbished main hydraulic pumps and main head fully reconditioned. Only requires new encoder to be fitted and this machine is ready to go. Features include. 100mm x 1.6mm Tube Maximum Capacity at 1.5D Anticipated Mandrel Withdrawal Fully automatic setup of clamps and follower Boosted Follower for tight radius thin wall tube bending. Long bed with 4000mm over mandrel. Comes with huge amount of tooling worth over AU$150k. Tooling Included: 101.6mm 152mm CLR 101.6mm 200mm CLR 76.2mm 114mm CLR 76.2mm 200mm CLR 76.2mm 238mm CLR 63.5mm 96mm CLR 57.2mm 86mm CLR 50.8mm 76mm CLR 44.5mm 67mm CLR 40 x 40 120mm CLR Gkedpfstrd T Tox Aftef 50 x 50 150mm CLR 60.3mm 150mm CLR 48.3mm 120mm CLR

Condition: good (used), Year of construction: 2005, control type: CNC control, - Max. bending angle: +/- 180 + 10° - Tube feed length: 4100 mm - Round steel tube up to 30 x 2.2 mm² - Round stainless steel tube up to 30 x 1.5 mm - Square tubes: 20 x 2.5 mm - Bending time for 90 degrees: 1.5 sec (advance) Gkedpfjx Eiw Hjx Aftef - Longitudinal feed speed: 450 mm/sec - Maximum bending radius: 125 mm - Freestanding bending head, 850 mm long - Bending axis drive: electrohydraulic

Condition: good (used), Year of construction: 1996, control type: CNC control, Tube diameter: 4-28 mm Wall thickness: / mm Minimum bending radius: 1.5 x D - 2.0 x D mm Control: Siemens LOGO Delivery rate: 4.5 l/min Max. bending angle +/-: 190° Nominal pressure: 250 bar Operating pressure: 3095 bar Delivery rate: 4.5 l/min Gkedpfex A Twxjx Aftjf Total power requirement: 1.5 kW Drive: Hydraulic cylinder and roller chain

Condition: used, Year of construction: 1993, Technical details: tube diameter: 80 mm tube diameter min.: 6 mm control for program: Gelma MM-1 tube pipe draw up length: 1800 mm weight of the machine ca.: 0,232 t dimension machine xH: 1,9 x 0,7 x 1,3 m Semi-automatic PIPE BENDING MACHINE Operating modes are manual but also semi-automatic Application: for multiple bending of pipes Gedpfx Aju Ibyyoftskf The swivel unit with bending preselection for 3 different bending angles in single and automatic mode. The machine is currently equipped with a stop bar for tube size Ø 10mm for 6 angle settings. The bending machine is movable/adjustable. Equipment/accessories: 6 cam rods/stop rods 6 control disks Bending tool for Ø 12mm *

Condition: ready for operation (used), Year of construction: 2017, Performance range: 20mm-60mm, max. bending angle: 180°+10°, max. bending radius: 150mm, effective length: 3048mm, bending height: 1050mm, max. section modulus: 12.1cm³, bending tolerance: +/-0.1°, operating pressure: 200bar, connected load: 4kW, machine dimensions X/Y/Z: approx. 2000mm/900mm/1200mm, weight: approx. 500kg. Documentation available. On-site inspection is possible. Gedpfswg E Dhsx Aftekf

Condition: new, Year of construction: 2025, Tube flaring machine, hydraulic flaring machine, 37° flaring machine, 90° flaring machine, ORFS flaring, JIC flaring, tube end processing, flaring device, tube processing machine, rotary forming machine Capacity: - For tubes from 6 - 42 mm Ø - Max. wall thickness (on tube-Ø 42 mm in steel) 4 mm - Cycle time (adjustable per form/shape) 4 - 15 sec. - Rotation/min 200 Machine equipment-/basic accessories: - For end forming of tube with angle between 37° to 90° (dependent on tooling) in one operation step via rotary principle - Depending on the tube diameter, 180 ° bends with a clearance of 145 mm can be machined - Length of the clamping dependent on tube size, approx. 1,0 x D - Forming length dependent on tooling - Operation and control via touch panel - Start of operation via pushbutton - Hydraulic forward movement, speed adjustable - Electric adjustable length stop to control the required flare diameter - Electric adjustable front feed of the tool holder - Electric adjustable rolling time - Clamping jaw can be swiveled, for easier loading of ORFS rings - Integrated drawer for storage of tools - Including transparent safety covers of the work area - Standard norm electric and hydraulic equipment - Machine stationary with underframe - Colour RAL 7047 grey, RAL 3020 rot Drives: - Clamping of the tube: servo-hydraulic - Front feed tool holder: servo-hydraulic - Rotation tool holder: electric Machine data: - Nominal pressure 250 bar, Operating pressure 200 bar - Operating voltage 400 Volt - 50 Cyl. - 3 Ph. - 4,5 kW The average consumption of the machine is approx. 1,8 kWh/h. As the consumption is highly dependent on factors such as tube size and geometry, speeds and power supply to the machine, it can only be used as a guide. - Length 1230 mm Gedpewzbc Nsfx Aftskf - Width 710 mm - Height 1240 mm - Weight approx. 800 kg

Condition: new, functionality: fully functional, Year of construction: 2025, Tube end processing machine, axial tube processing, tube end forming machine, tube end processing, axial tube forming, tube forming machine, expanding, reducing, expanding machine, reducing machine, beading, flaring Gjdpfx Afowvq Svotskf