Used Tube Punch for sale (3,466)

Condition: used, Single-column eccentric press RICHTER type PEKRS 80 Year of construction 1970 - overhaul 2024 Compressive force 80 ton. throat depth 350 mm Table size 900 x 650 mm Hole in the clamping table Ø 200 mm ram surface 700 x 500 mm Stroke rate 70 strokes/min. Stroke adjustment 6 - 100 mm ram adjustment 85 mm Installation height max. 400 Clamping pin bore Ø 50 mm Table height above floor 810 mm Motor power 8 kW Mains connection 400 Volt, 50 Hz - ORTLINGHAUS pneumatic clutch/brake combination - HERION XSz 32 press safety valve - Pneumatic ram compensation cylinder - Overload protection with breaker plate in ram - Central grease lubrication with hand pump Space requirement L x W x H 1800 x 1250 x 2830 mm Weight 5.7 tons Very good condition Technically overhauled and converted to the latest UVV with new electrics Control conversion in 05/2024 - suitable for manual insertion work - in accordance with DGUV Information 209-030 Press inspection and Machinery Directive 2006/42/EC Low Voltage Directive 2014/35/EU EN ISO 16092-1: Safety of machine tools - Presses - Part 1: General safety requirements EN ISO 16092-2: Machine tools - Safety of presses - Part 2: Mechanical presses - Control system with plain text error messages and diagnostic screen for rapid fault localization - New electrical cabinet, mounted on the side of the machine - completely based on SIEMENS, with PLC S7-1200 PROFIsafe and 7" TFT touch display - Two-hand control panel with emergency stop and engagement lock Redpfx Aloi Db Ibsreu - el. foot switch - Cam switch unit with run monitor control - Stroke release via HERION XSz 32 press safety valve with pneumatic pressure compensator - New wiring of the machine - Updated operating instructions The machine is equipped with 6 operating modes: 1 = Set-up 2 = Single stroke two-handed 3 = Single stroke foot 4 = continuous run foot 5 = automatic continuous run 6 = reverse run

Condition: used, Semi-automatic tube bending machine, mandrel tube bender MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Serial No. Year of construction for simultaneous bending of two steel tube sections up to Ø 12 mm Bending angle max. 90° Tube diameter max. 12 mm Redpfxjpu R Nve Alrju Mandrel length approx. 65 mm Rated power 3.5 kW Compressed air max. 6 bar / approx. 1 litre per bending cycle Power supply 400 Volt, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Angle input control via STÖBER Controlbox Series 4000/5000 - SIEMENS S7-200 control with TD200 display - Machine without bending tools and without tool storage pins 25 x 183 mm - Only 1 bending mandrel available (see pictures). Required space (L x W x H) 1000 x 1000 x 1500 mm Weight 390 kg Good condition

Year of construction: 2008, condition: ready for operation (used), X-axis: 2500mm, Y-axis: 1270mm, positioning speed X-axis/Y-axis: 80/90m/min, simultaneous axis speed: 100m/min, punching capacity: 200kN, number of turret stations: 51, max. material thickness mild steel: 3.2mm, max. material weight at traverse speed F1/F4: 50/150kg, positioning accuracy: ±0.1mm, stroke rate X-axis: 350/min, stroke rate Y-axis: 260/min, max. stroke length: 42mm, max. feed speed X-axis/Y-axis: 80/60m/min, turret speed: 30rpm, compressed air requirement: 500l/min, operating air pressure: 5bar, connected load: 19kVA, length: 4165mm, width: 5120mm, height: 2082mm, height with mirror: 3028mm, weight: 13t, operating hours: 4531h, regularly maintained by the manufacturer, with documentation, without punching tools. An on-site inspection is possible. Rjdoza E S Depfx Alreu

Condition: new, Year of construction: 2025, Model: K110 K230 K360 Working Area: from 8649×1398×1811mm to 10000×3500×2100mm Laser Output Power: 3000w/2000w/1500w/1000w X/Y-axis positioning accuracy: 0.05mm X/Y-axis repositioning accuracy: 0.03mm X/Y-axis Max. linkage speed: 60m/min 1. Integrated full protection cover Integrated full protection cover design, installing in place, greatly reducing installation time. 2. Bodor Genius T needle nose auto-focusing laser head Bodor Genius T needle nose auto-focusing laser head, applicable for all kinds of tubes such as angle steel, channel steel, I-beam, etc. 3. Rectangular Tube Welded Bed Simple structure and flexible layout. 4. Bodor Thinker 3.0 System Rodpfx Asg Rgt Uolrou The dedicated control system of tube cutting machine integrated with the most advanced technology, can cut angle steel and channel steel directly without nesting and returning home. 5. Applicable to smaller clamping diameter The rear jaws can clamp the pipe to go through the front chuck, which greatly shortens the physical distance between the cutting head and the rear chuck jaws. Tail length is reduced to 70mm and the material utilization rate is increased to 99%. 6. Ergonomics Loading and operating on both sides; and humanized interaction interface, convenient and smooth operation, and favorable user experience. 7. Integrated design Integrated design of electric control cabinet and main body, saving the space occupied, standardizing the line installation.

Condition: used, functionality: fully functional, For sale is a MABI 8Z dished end punch which we used as a multi-hole punch. Rsdpfx Alex Dbunsreu

Condition: good (used), Year of construction: 2005, control type: CNC control, pipe diameter (max.): 30 mm, Tube diameter: 30 mm Wall thickness: 2 mm Max. bending angle: +/- 180 + 10 ° Redpfx Aleza A Hrersu Tube insertion length: 4100 mm - Round steel tube up to 30 x 2.2 mm² - Round stainless steel tube up to 30 x 1.5 mm - Square tubes 20 x 2.5 mm - Bending time for 90 degrees: 1.5 sec. (feed) - Longitudinal feed speed: 450 mm/sec. - Maximum bending radius: 125 mm - Freestanding bending head, 850 mm long - Bending axis drive: electrohydraulic

Condition: excellent (used), Year of construction: 2008, control type: CNC control, controller manufacturer: ESA TOUCH PANEL, pipe length (max.): 4,000 mm, bending radius (max.): 180 mm, bending radius (min.): 10 mm, overall weight: 3,700 kg, total length: 6,000 mm, total width: 1,800 mm, total height: 1,800 mm, Tube bending machine Transfluid - DB630 A3 CNC MACH-ID 9616 Make: Transfluid Type: DB630 A3 CNC Control: ESA TOUCH PANEL Year: 2008 Max.Tube Ø: 30mm Min. Tube Ø: 4mm Max. Wall thickness:4mm Max. Bending radius:180mm Min. Bending radius:10mm Max. bending length:4000mm Redpfx Aley N Rv Isrsu 3e dimsion bending:Yesmm/min. Number of tools: 10,12,15,16,18,20,22,28 Length: 6000mm Width: 1800mm Height: 1800mm Weight: 3700kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Manufacturer: AXA Type: HFB 600 Rsdpot Tdp Tefx Alrsu Control system: Siemens 840D Solutione Line Year of construction: 2015 Specifications: Metric Metric US Standard There are no specifications for this machine (yet). Dimensions (estimate) length 7800 mm width 2300 mm height 2250 mm weight 15000 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details. Finishing of sealing surfaces The finishing of the sealing surfaces of the approx. 17m long tubes is done by an NC-controlled feed unit and an NC-controlled facing slide with 2 ABS tool holders for either lathe tools, measuring sensors or measuring probes. The work piece is first measured via the measuring sensors in the slide heads and aligned by the adjustable roller supports. The tube is hydraulically tightened into position by the swimming jaw once it lies at a right angle and centric to the facing slide head. The interchangeable measuring sensors calculate how to process the surface whic

Condition: good (used), Manufacturer: Tracto Technik Type: TUBOMAT Year of construction: 1996 Pipe bending machine with electric control, 4-fold bending angle pre-selection and digital display Hydraulic bending drive operated by hand lever valve Hydraulic bending drive, operated by hand lever valve Follower-type pressure die (sliding guide) Hydraulic mandrel retraction Pipe circular saw with coolant lubrication and automatic feed Pipe deburring unit for internal and external deburring Hydraulic power unit as basic seating for attaching a cutting ring assembly or flaring device Machine mobile and flexible to use Specifications Metric US Standard Max. Product Ø 42 mm Min. product Ø 6 mm Max. Wall thickness 3 mm Rsdpfx Aet Dk Ukolreu Max. Bending radius 5 mm Min. bending radius 180 mm Max. Bending length 2000 mm Deburring device Yes Sage device Yes Flanging device Yes Dimensions (estimate) Length 3500 mm width 1000 mm height 1200 mm weight 1000 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: excellent (used), functionality: fully functional, Year of construction: 1989, pipe diameter (max.): 42 mm, pipe length (max.): 3,000 mm, bending radius (max.): 180 mm, wall thickness: 3 mm, Pipe bending machine with electric control, 4-fold bending angle pre-selection and digital display  Hydraulic bending drive operated by hand lever valve Hydraulic bending drive, operated by hand lever valve Follower-type pressure die (sliding guide) Hydraulic mandrel retraction Pipe circular saw with coolant lubrication and automatic feed 6 mandrels up to 24 mm included x 3000 mm Pipe deburring unit for internal and external deburring Hydraulic power unit as basic seating for attaching a cutting ring assembly or flaring device  Rodpfxouccw He Alreu Machine mobile and flexible to use Max. tube Ø: 42mm Min. tube Ø: 6mm Max. Wall thickness: 3mm Max. Bending radius:5mm Min. bending radius:180mm Max. bending length:3000mm Deburring attachment:Yes Sawing attachment: Yes Flair attachment: Yes Length: 3500mm Width: 1000mm Height: 1200mm Weight: 1000kg

Condition: used, Punching force: 350 kN For example, punch a 23 mm hole in 12 mm steel Rodpfxjy Saaho Alrju Stroke triggering via foot switch Support table with stops Assortment of tools is included in the price

Condition: used, Year of construction: 1988, gebraucht 1988 090151 prompt, Zwischenverkauf v Italien 12800 € 1 42 mm 4665 mm 800 mm 1160 mm 1470 kg 42 x 2,5 mm 40 x 1,2 mm 30 x 40 x 1,7 mm 40 x 30 x 1,3 mm 255 mm 22 mm 180 ° 90 °/s 5.5 kW 120 l Capacity specifications refer to 400 N/mm² Maximum bending radius with pipe guide rollers: 255 mm Maximum bending radius with pipe guide slide: 175 mm Minimum bending angle: 4° Maximum usable length without positioning device: 3900 mm Maximum usable length with positioning device: 3370 mm Adjustable mandrel extension travel from 8 mm Opening and closing travel of the counter-clamping jaws: 0-45 mm Opening and closing travel of the rollers or slides: 12-22-42 mm Operating manual in German Machine does not comply with AMVO or UVV regulations Rodpfx Aljxx A Eksrou Tools not included BUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISE We offer you maximum security and complete transparency. • HONEST INSIGHTS: Detailed photos and functional videos of the current condition • LIVE ON-SITE CHECK: Live testing is possible at our facility • DIGITAL DEMONSTRATION: Individual live demonstration via video call • RISK-FREE PURCHASE: 14-day return policy Details:

Condition: new, Year of construction: 2022, pressure 55 t stroke 37 Min./20 mm throat 500 mm stroke max. 60 mm work height max. 1060 mm Rodpfxewp Tcqo Alrsu total power requirement 5 kW

Year of construction: 2003, operating hours: 69,600 h, condition: used, functionality: fully functional, Used TRUMPF-PULZER CNC35L tube bending machine We are offering a used TRUMPF-PULZER CNC35L tube bending machine for sale. Technical data: Manufacturer: TRUMPF-PULZER Type: CNC35L Machine No.: 837 Year of manufacture: 2003 Electrical connection values: Voltage: 400 V / 3~ Frequency: 50 Hz Rjdszaqm Tspfx Alrju Current consumption: 21 A Connected power: 14 kVA Bending capacity: Bending direction: Left-hand Suitable for tubes made of steel, stainless steel and non-ferrous metals Maximum tube dimensions: Ø 35 x 2 mm with a bending radius of R = 2 x D Tube feed length: approx. 3,000 mm Equipment: Mandrel bending device Dimensions and weight Installation dimensions (L x W x H): approx. 5,550 x 2,520 x 1,560 mm Machine weight: approx. 2,500 kg Description: The TRUMPF-PULZER CNC35L is a robust and proven CNC tube bending machine for the precise processing of steel, stainless steel and non-ferrous metal tubes. Thanks to the integrated mandrel bending device, the machine is particularly suitable for demanding bending tasks with high quality requirements. The machine dates from 2003 and is offered in used condition. If you are interested or would like further information, please do not hesitate to contact us. Inspections are possible by arrangement.

Condition: used, functionality: fully functional, Year of construction: 1993, machine/vehicle number: 4422559493014, Equipment: CE marking, Peddimax 600 Equipment - Flat, profile, and bar steel shear - Notching & punching unit 600 kN - Mechanically adjustable profile and flat steel hold-down device Rjdjrknnfspfx Alrsu - Quick-change punch system Punching table - Universal punch saddle - Material support table for notching device - Various punches and dies

Condition: new, functionality: fully functional, Year of construction: 2021, For sale: Brand new, never-used DAVI bending machine. *MAIN FEATURES MCP 18* *1. Type and Capacity* - *3 hydraulically driven rollers*, pyramid configuration - *Shafts Ø 180 mm* → this is the "18" in MCP 18 - *Bending*: round, square, rectangular tubes, angles, flat bars, UPN, IPE, HEA... all b235 profiles Rjdpjy N Rbwjfx Alrju *2. Indicative capacities on MCP series* DAVI does not provide the exact MCP 18 datasheet online, but for the equivalent MCP range: Profile Approx capacity MCP 18 Round tube Ø 6" to 8" depending on wall thickness Solid square 80x80 mm to 100x100 mm Angle 120x120x12 mm UPN UPN 200 - 240 IPE flat flange IPE 200 - 240 Actual figures depend on wall thickness and steel grade. The 18 cm Ø shafts make this a mid/high-category machine. For all available options, please refer to the photo in the listing.

Condition: used, functionality: fully functional, Combined profile shear (ironworker) for metalworking. Punches, cuts, notches, and severs structural steel (angles, flat bars, round bars, square bars) in a single machine. Robust East German/West German industrial design – extremely durable, easy to maintain, no high-tech frills. Features a large base plate and multiple workstations. Ideal for locksmiths, steel construction companies, metalworkers, blacksmiths, training workshops, or well-equipped hobbyists with sufficient space. A comparable new machine costs well over 15,000 EUR. Rodpfezabv Sox Alrsu Technical data: - Design: Combined profile shear with multiple stations (punching, shearing, notching, profiling) - Drive: Three-phase motor 400 V - Shear blades: included - Punching tools: included (see photo) - Steel base plate: cast, very stable - Machine weight: approx. 1,500 - 2,500 kg - Year of manufacture: approx. 1970s-1980s Collection / Transport: Self-collection with a heavy-duty forklift (>= 5 tons) or crane. Loading on site is possible. Shipping via a low-bed trailer is available by arrangement.

Condition: new, Year of construction: 2025, All-round fiber laser metal tube cutting machine Multiple function options help the laser tube cutting machine be used in numerous tube cutting processes. The slender nozzle allows the laser tuber cutter to avoid interference and cut various types of tubes, including special-shaped tubes like H-Beam, P-Beam, I-beam, etc. Cutting machine clamping becomes convenient, easy and fast, with 3 seconds at the soonest to clamp and high repeat precision Rjdpfxehwrhfe Alreu Cutting performance and efficiency are improved by maintaining gas flow steady with little turbulence. BodorGenius, combined with the lightning-quick piercing process, completes the whole piercing during it moves down on Z-axis. Thanks to the technology, no reworking is necessary for medium and thick sheet piercing. Angle steel and channel steel cutting are standard with no need fior additional installation. Optimized edge searching method and algorithm guarantee higher cutting precision and better steadiness of the laser cutter. Condition: New Laser Type: Fiber Laser Laser Power: 1500W, 2000W, 3000W, 6000W Maximum machinable tube length: 6500mm/9200mm Chuck drive types: NC electric chuck Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: new, Year of construction: 2025, All-round fiber laser metal tube cutting machine Multiple function options help the laser tube cutting machine be used in numerous tube cutting processes. The slender nozzle allows the laser tuber cutter to avoid interference and cut various types of tubes, including special-shaped tubes like H-Beam, P-Beam, I-beam, etc. Cutting machine clamping becomes convenient, easy and fast, with 3 seconds at the soonest to clamp and high repeat precision Cutting performance and efficiency are improved by maintaining gas flow steady with little turbulence. BodorGenius, combined with the lightning-quick piercing process, completes the whole piercing during it moves down on Z-axis. Thanks to the technology, no reworking is necessary for medium and thick sheet piercing. Angle steel and channel steel cutting are standard with no need for additional installation. Optimized edge searching method and algorithm guarantee higher cutting precision and better steadiness of the laser cutter. Condition: New Laser Type: Fiber Laser Laser Power: 1500W, 2000W, 3000W, 6000W Maximum machinable tube length: 6500mm/9200mm Chuck drive types: NC electric chuck Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT Rsdpohwri Sofx Alrou CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: excellent (used), functionality: fully functional, Year of construction: 2010, laser power: 4,000 W, X working area max.: 3050 mm Y working area max.: 1550 mm Control: Rexroth IndraMotion MTX Laser power: 4,000 watts Standard equipment: Machine - Sturdy, easily accessible C-frame - Coordinate guidance for high-precision machining - Linear tool changer with 21 tool stations and 4 clamps - Maintenance-free three-phase drive motors - Repositioning device with programmable hold-down - Foot switch for closing clamps - 2 good parts containers - Automatic shutoff Laser station - TruFlow laser - High-frequency excitation - Cooling unit - TASC 3 laser controller - Enclosed beam guidance - Beam tube ventilation with compressed air - Programmable cutting gas pressure - Laser cutting head with 170 mm focal length - Universal quick-change cutting head device UTI with bus connection - LensLine - FocusLine - ControlLine - NitroLine - SprintLine - ContourLine - FlyLine - PlasmaLine - High-speed cutting - Additional Xp and Yp axes - Ejector cylinder for laser parts - Fast flap for laser parts 500 x 500 mm - Liftable laser cutting support - Slag cone detection - Laser logbook function Punching station - Electro-hydraulic punching head Redpfoy Saqgox Alrsu - Rotatable mono-tool holder - Tool length compensation - Programmable hold-down with adjustable force - Stroke counter for punches - Spray lubrication for punches - Punch slug extraction - Warp detection - Flap for punched parts 500 x 500 mm - Fill level monitoring in the punching console Control - Open control system based on Bosch Rexroth IntraMotion MTX - Operating panel with 15" TFT touchscreen - Program management and 80 GB storage capacity - Diagnostic function with laser logbook - Integrated technology data - Teleservice Data transfer - Network connection RJ45 and USB interface Safety - CE marking - Multi-beam light barriers - Monitoring system for, among others, gas pressure, temperature, cooling water - Hydraulic quick shut-off - Protection against stray radiation - Compact extraction unit - TruFlow 4000 - Vibration-dampened installation - Thread forming function - MultiTool function - Chip conveyor with tilting container - Active die - Ejector for small parts - Brush tables with loading aid - Marking function - Repositioning cylinder - Warp detection

Condition: good (used), functionality: fully functional, Year of construction: 2019, controller model: Rexroth IndraMotion MTX, laser type: CO₂ laser, laser hours: 980 h, laser power: 4,000 W, punching force: 22 t, Equipment: CE marking, nozzle changer, safety light barrier, Machine - C-frame - Coordinate guide - Linear magazine with 25 stations for clamps and tools - 4 x hydraulic clamps - Drives with maintenance-free three-phase motors - Repositioning system with programmable hold-down - Flap for punched parts 500x500mm incl. sensor - Foot pedal for closing clamps - FocusLine - NitroLine - FastLine - FlyLine - Additional XP and Yp axes - Ejector cylinder for laser parts - Fast flap for laser parts 500x500mm incl. sensor - Liftable laser cutting support TRUMPF Laser - TruFlow 4000 laser incl. LensLine and optimized standby - High-frequency excitation - Fine filtration of compressed air for beam tube ventilation - Closed beam guidance Cutting Head - Lens cutting head with 170mm focal length - Universal quick-change device for cutting head - LensLine - ControlLine Punching Head - Electro-hydraulic punching head - Rotatable mono-tool holder - Programmable hold-down position - Tool length compensation - Punch slug extraction - Calculation of fill level in the punching console - Stroke counter for punches - Spray lubrication for punches - Fill level monitoring for tool lubrication - Stripper position measuring system with sheet thickness measurement function Control System - TRUMPF control based on Rexroth IndraMotion - Touch panel with 19" TFT color display - Integrated technology data - Programmable cutting gas pressure - Remote Support interface - Automatic shut-off with wake-up function - Production planner Functions - PlasmaLine Data Transmission - USB interface - RJ-45 network interface - Wireless Operation Point Safety - CE marking - Two-beam safety light barrier - Monitoring system for gas pressure, temperature and cooling water - Emergency stop for drives - Warp detection - Protection against stray radiation Extended Standard Equipment: - Network installation via Remote Support - Chiller (water-air) Rodpfx Asy Sappjlreu - Compact extraction system - 1st locating pin (inside right) - 2 finished parts containers - Chip container - 40 used RTC cassettes + die plate Punch Quality Package - MultiShear - Deburring and rolling technology - Adaptive stroke calibration - StripLine Forming Package - Thread forming incl. thread former breakage control - Marking/fast beading - MultiBend - Height-adjustable clamps - Automatic nozzle changer - MultiTool - Engraving - Smart Punch Monitoring with sheet format detection - 4 individually openable clamps - Automatic clamp closing with mechanical sensor zero stop - Repositioning cylinder - Vibration-damped installation - Chip conveyor with tilting container - Foot pedal start incl. rear-view mirror - Brush tables with loading and unloading support - Ejector unit for small parts - CO2 extinguishing system for compact extractor - Connection piece for exhaust air duct of compact extractor MobileControl App SheetMaster (AK08) UF - Loading station with spreader magnet - Simultaneous loading and unloading during main time - Peeling system incl. positioning aid for oversize formats - Additional positioning aids for medium format - Additional positioning aids for large format - First add-on package with 9 suction cups (incl. vacuum ejector) - Unloading monitoring for laser parts - Loading of blanks GripMaster 4000 x 1500 mm SortMaster Pallet 4 pallets longitudinal ToolMaster Linear 54 stations with simultaneous tool setup during main time - Safety devices for warehouse connection incl. 2nd light barrier circuit - Warehouse interface

Condition: good (used), Year of construction: 1999, operating hours: 52,324 h, functionality: fully functional, X working area max.: 1270 mm Y working area max.: 1270 mm Control: Bosch Type 3 Basic Standard equipment: - Robust C-frame - Safety light barriers - Coordinate guide with integrated linear magazine - 2 clamping claws - Automatic tool changer - Automatic repositioning - Tool length compensation - Forming capability - Mono tool holder with 360° rotation for all tools - Programmable hold-down device - Multitool drive - Punch slug extraction - Brush tables Rodpjy Sat Ujfx Alrou - Part chute 200 x 200 mm, sorting of parts into 2 containers - NC-controlled, digital, maintenance-free three-phase drives - Network interface RJ34 - 3.5" floppy disk drive - TOPS 2000 graphical programming - Online diagnostics via modem - Operating manual + Vibration-damped installation + Multitool + Thread forming + Start post

Condition: good (used), functionality: fully functional, Year of construction: 2013, laser power: 2,700 W, X working area max.: 2500 mm Y working area max.: 1250 mm Control system: Rexroth IndraMotion MTX (basic version) Laser power: 2700 Watt Standard Equipment Machine - Sturdy, easily accessible C-frame - Coordinate guide system for high-precision machining - Linear magazine with 23 tool stations and 2 clamps - Maintenance-free three-phase drive motors - Repositioning unit with programmable hold-down device - Foot pedal for clamp closing - Alignment pin (right inside) - Ball tables - 2 parts flaps 500 x 500 mm incl. sensor for parts ejection - Two good parts containers - NitroLine - Focus Line - FastLine - FlyLine - Slag cone detection - Ejector cylinder for laser parts TRUMPF Laser - TruFlow 2000 laser with LensLine and optimized standby mode - High-frequency excitation - Cooling unit - Laser control - Enclosed beam guidance - Fine filtration of compressed air for beam tube ventilation Cutting Head - Lens cutting head with 170 mm focal length - Universal cutting head quick-change system UTI with bus connection - ControlLine Punching Station - Electro-hydraulic punching head - Rotatable mono-tool holder - Tool length compensation - Programmable hold-down device with manually adjustable holding force - Stroke counter for punch and thread-forming - Punch spray lubrication - Punch slug extraction - Measurement of fill level in punching console - Level monitoring for thread-forming and tool lubrication Control - TRUMPF control based on Rexroth IndraMotion MTX - Operating panel with 17" touch screen - Integrated technology data - Teleservice via internet - Programmable cutting gas pressure - Automatic shutdown incl. wake-up mode - Program management - Production scheduling Data Transfer - Network connection RJ45 and USB interface Safety - CE marking - Two-beam light curtain - Monitoring system for gas pressure, temperature, and cooling water - Emergency stop - Protection against stray radiation - Compact extraction unit + Brush tables + Lowerable die + MultiTool function + Softpunch function + Marking function + Chip conveyor with tilting container + Roll technology functions: roll knurling, roll deburring, roll shearing, roll offsetting, roll bead forming, roll cutting + Die spray lubrication + Blow-off device for small parts + 1 pc. additional clamp + Smart Punch Monitoring (punch breakage monitoring) + Vibration-damped installation + Repositioning cylinder + Warping detection + Parts conveyor belt in punching area + Parts conveyor belt in laser area Redpfxsy Saqms Alrju + GripMaster (2500x1250) + Scissor lift table + Scrap grid pallet + SheetMaster (2500x1250) (AK04) + Peeling system + Automatic clamp closing + HZP loading/unloading + TwinCarts loading station with toothed belt drive + TwinCarts unloading station with toothed belt drive

Condition: good (used), Year of construction: 2009, operating hours: 44,287 h, functionality: fully functional, X Working area max.: 2500 mm Y Working area max.: 1250 mm Operating hours: 44,287 hours Control system: Bosch PNC-P Standard equipment: Machine - Stable, easily accessible C-frame - Coordinate guide for high-precision machining - Linear magazine with 18 tool positions including 2 clamps - Drives with maintenance-free three-phase motors - Reloading device with programmable hold-down device - Ball tables - Part chute 180 x 150 mm - Automatic shut-off Punching head - Hydraulic punching head - Rotatable mono-tool holder - Programmable hold-down device - Tool length compensation - Punch spray lubrication - Punch slug extraction - Forming Rsdpfx Aey Sathjlrou Control system - Open control system based on Bosch PNC-P - Control panel with 15" TFT color screen - Program management - Integrated Technology Data - Teleservice Data Transfer - USB Interface and Network Connection Safety - CE Marking - Multi-Beam Light Barriers - Hydraulic Quick Shutdown + Multitool Function + MultiShear Function + MultiBend Function + Thread Forming Function + Marking/Fast Beading Function + Deburring and Rolling Technology Function + Soft Punch Function + Movable Support Table + Part Slide Sensor + Vibration-Dampened Installation + 2nd Stop Pin + Bow Detection

Condition: good (used), functionality: fully functional, Year of construction: 2003, laser type: CO₂ laser, laser power: 2,700 W, X working area max.: 6500 mm Laser power: 2700 watts Control: SINUMERIK 840D Standard equipment Rodpfey Sanrox Alreu TRUMPF loading unit: - Tube feeder for round, square, and rectangular tubes via buffer section with X-stop for tube lengths min. 3 m and max. 6 m - Semi-finished product length measurement - Transfer unit to the machine - Tube magazine with tube separation, alignment, and transfer to tube feeder, max. bundle weight 4000 kg - Good parts removal up to max. 3,000 mm with chip conveyor - Additional tube supports - Tube handling unit: Rotating and feed station: Rotating clamping unit with pneumatically actuated clamping jaws for tube lengths up to 6000 mm and tube diameters of d = 20 - 150 mm, 2 clamping ranges: d = 20 - 85 mm and d = 85 - 150 mm - Carriage unit with linear guidance - Feed station with motor drive, including connection for extraction - Tube support: Between tube support and traverse chuck, five automatically retractable support elements with form shells are provided - Traverse chuck: With a passage of d = 150 mm - The tubes are positioned via the clamping jaws centrally in the Y and Z axes relative to the rotational axis for the cutting process - 2 sets of clamping jaws for round, square, and rectangular tubes (simple design), clamping range 20 - 85 mm, 85 - 150 mm - Good part removal (unloading cabin for round and rectangular tubes) - Sorting options: 2 finished parts (front and rear), 1 flat - Scrap conveyor; programmable sorting; max. scrap length 300 mm (collection container, scrap belt) - Finished part length up to 3000 mm can be automatically unloaded (front and rear) Safety equipment: - Compact extraction unit Filter system designed for the separation of airborne particles produced during laser cutting of metals - Light barrier: Loading area secured by light barriers - Protective cabin: In the area of the cutting head, a Macrolon sheet metal combination is installed for laser radiation protection - Chip conveyor: Conveyor belt for discharging cut remnants - Operating manual