Turntable / rotary table / accumulating table

W&W

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: 16501575, volume flow: 4,800 m³/h, input voltage: 380 V, power: 2.5 kW (3.40 HP), Equipment: type plate available, The resulting dirt particles, emulsion and oil mist, as well as smoke, are captured directly at the source and passed through the individual filtration stages. The separated liquid collects at the bottom of the unit and can be returned to the machining center via the siphon. In the first filtration stage, larger particles are retained by an aluminum pre-filter to protect the downstream high-performance fleece filters. The second filtration stage removes the majority of fine emulsion and oil mist. This stage consists of an aluminum frame equipped with a G4 filter mat and an F5 filter mat according to DIN 24185 / EN 779. The filter mats must be replaced depending on the degree of contamination. The third filtration stage consists of a large-area HEPA filter of class H13. A consistently high filtration efficiency of 99.95% at a particle size from 0.3μ DOP is ensured here. Type testing in accordance with DIN EN 1822-1 H13 allows the filtered air to be returned to the workspace. Gjdpfeyz Sn Nsx Aa Aobk

Year of construction: 2020, operating hours: 13 h, condition: excellent (used), 1 x Urschel E Tran slicer Only 13 hours on the machine Previously was going to be used to slice bread chips, but can be used for veg etc... Gedpfx Aaew Hq T Us Aebk Located in Switzerland

Condition: excellent (used), UNLOADER (BRIDGE-FRAME) WITH DOUBLE STORAGE STATION Gantry (Portal) machine, belonging to the line (SOFIT code: W05025) Vacuum system (with its pump) N. 2 Vertical supporting columns of the top supporting beam N. 1 Horizontal top supporting beam (where the carriage slide on) N. 1 Motorized sliding carriage with horizontal metal arms N. 2 Horizontal metal arm with vacuum cups, adjustables N. 2 Out-side rollers way (on gound) to out-feed pile of panels from the Unloader N. 1 Out-side motorized rollers table (which brings panels to the Unloader) Separate electric and command panel Electronic Programmer PLC MAGELIS Perimetral safety metal grids Working capacity (cycles/min) 15-18 (ca.) Min/Max panels thickness mm 10 - 60 (ca.) Min dimensions of the panels mm 210 x 230 (ca.) Max dimensions of the panels mm 1200 x 3200 (ca.) Total installed motor power Kw Gjdpfoyywl Rox Aa Asbk

Condition: used, tank capacity: 8,750 l, GENERAL Design: rectangular Comments: Each tank contains 2 cooling plates inside; 1 manhole approx. 300 x 400 mm in the front bottom; feet equipped with loose, height-adjustable spherical cap screws (possibly not all feet complete; cap screws not included in the total height, total height will increase accordingly if used); feet are slightly off-set Overall width: 1,620 mm Overall height: 2,700 mm Overall length: 2,950 mm Heating/Cooling: available Location: Bremen Nameplate: Volume: 8,750 liters Product-contact material: V2A 1.4301 (AISI304) Condition: used Last use: wine storage TANK Mounting: feet Number of feet: 4 pcs HEATING/COOLING JACKET Temperature control inside: cooling plate EQUIPMENT Gjdpfxeycktrs Aa Aebk Outlet: DN40 DIN 11851 MATERIAL SPECIFICATION Temperature system material: stainless steel Foot material: stainless steel

Condition: ready for operation (used), Functions according to the magnetic particle technology, with documentation and accessories, an inspection is possible. Gedpeq Npf Usfx Aa Aobk

Condition: new, I am offering a brand new Siemens SIMOTICS motor (1FE series) – a professional servo/spindle motor designed for inverter duty. This is a high-grade industrial motor, commonly used in CNC machine tools, delivering high power, precision, and reliability. The motor comes from warehouse stock (New Old Stock – NOS), unused and stored in original Siemens packaging. ⚙️ Technical Data Manufacturer: Siemens Series: SIMOTICS Gbsdpfxoyxqmxo Aa Aok Model: 1FE1114-6WW11-1BN2-Z-T56 Power: 20.9 – 26.8 kW Voltage: 425 V Current: 58 / 85 A Nominal speed: 1000 rpm Max speed: 6000 rpm Max torque: 330 Nm Duty cycle: S1 / S6-40% Cooling: water-cooled Temperature sensor: KTY84-130 Protection rating: IP00 Insulation class: F (155°C) 📦 The set includes: Siemens SIMOTICS motor Original Siemens packaging (as shown in the pictures) 📌 Key advantages: ✔️ Condition: NEW (warehouse stock / NOS) ✔️ Made in Germany ✔️ Genuine Siemens industrial quality ✔️ Ideal for CNC / machine tools / automation ✔️ High power and torque

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, We have a Buhrs - W+D BB700 16K S1 year 2011 servo envelope inserting system available. The condition of this machine is very good and the machine has always received its mandetory maintenance. The machine is prepared for a Mueller and/or KERN transactional channel for feeder/collating/folding A4 documents. The Mueller and/or KERN system channel can be offered in or excluded at the machine. We can even offer the Mueller channel as a continues system with a Mueller unwinder, paper cutter, merger and folding station. Other feeders and camera's optional possible! Year of built: 2011 Configuration: - 6 station base - 4x RF2 rotary feeder - 2x HF vacuum friction feeder - Divert bin 1 - On-edge conveyor Prepared for a Mueller and/or KERN transactional channel for feeder/collating/folding A4 documents. Envelope formats: - min. 105 × 162 mm C6/DL - max. 250 × 353 mm B4 Product formats: - min. 80 × 105 mm A6 - max. 229 × 324 mm C4 Product thickness: - 3 mm for rotary feeder - 10 mm for shuttle feeder - 15 mm for vacuum/friction feeder Gbjdewml S Ejpfx Aa Ask - 70 gsm 16,000 cycles per hour

Condition: excellent (used), GT2 tray sealer with E-Seal option. In very nice condition. Gedorm Tg Ispfx Aa Asbk

Condition: used, Year of construction: 2007, weight of the machine ca. 290 kg dimensions of the machine ca. 1050 x 560 x 840 mm The SHARC T power source is a TIG welding unit for direct current welding (DC version) and for direct and alternating current welding (AC/DC version) based on an innovative arc forming process developed by Hermann GmbH. In application, the SHARC process leads to higher welding speed with simultaneous improvement of the weld quality and reduction of the ancillary welding costs (less distortion, improved penetration, reduced annealing colours of the workpiece, less hardening of the transition edge zones and, if required, no need for filler materials). --> Technical data Welding current type: DC --> Mains voltage (50/60 Hz): 400 V --> Phases: 3 --> Setting range: 10 -320 A --> Electrode setting range: 25- 280 A --> Welding voltage: 22 V --> Open circuit voltage without HF: 70 V --> Open circuit voltage with HF: 90 V --> Primary power: 23 kVA Gbsdpfx Aaswf Rgrj Ajk --> Duty cycle 60%: 320 --> Duty cycle 100%: 260 --> Cooling type: F --> Protection class: IP 23

Condition: used, Year of construction: 2007, weight of the machine ca. 290 kg dimensions of the machine ca. 1050 x 560 x 840 mm The SHARC T power source is a TIG welding unit for direct current welding (DC version) and for direct and alternating current welding (AC/DC version) based on an innovative arc forming process developed by Hermann GmbH. Gedpewf Rg Eofx Aa Asbk In application, the SHARC process leads to higher welding speed with simultaneous improvement of the weld quality and reduction of the ancillary welding costs (less distortion, improved penetration, reduced annealing colours of the workpiece, less hardening of the transition edge zones and, if required, no need for filler materials). --> Technical data Welding current type: DC --> Mains voltage (50/60 Hz): 400 V --> Phases: 3 --> Setting range: 10 -320 A --> Electrode setting range: 25- 280 A --> Welding voltage: 22 V --> Open circuit voltage without HF: 70 V --> Open circuit voltage with HF: 90 V --> Primary power: 23 kVA --> Duty cycle 60%: 320 --> Duty cycle 100%: 260 --> Cooling type: F --> Protection class: IP 23

Condition: used, Year of construction: 2005, functionality: fully functional, measuring range X-axis: 700 mm, measuring range Y-axis: 1,000 mm, measuring range Z-axis: 600 mm, Equipment: type plate available, Mitutoyo Crysta Apex C7106 coordinate measuring machine Temperature compensation on all axes Active vibration isolation system from BILZ X-axis measuring range = 700 mm Y-axis measuring range = 1000 mm Z-axis measuring range = 600 mm Measurement uncertainty = 1.9 + 3L/1000 (µm) Renishaw PH10MQ probe head Gbodpfx Aswhb A Noa Aok Renishaw SCR200 interchangeable rack Renishaw TP200 sensor Renishaw TP200 modules = 6 units MCosmos measuring software WIN10 PC system, 27" monitor Reference sphere / calibration sphere Optional software upgrade Optional hardware upgrade Full service available upon request

Condition: used, Year of construction: 2007, weight of the machine ca. 290 kg dimensions of the machine ca. 1050 x 560 x 840 mm The SHARC T power source is a TIG welding unit for direct current welding (DC version) and for direct and alternating current welding (AC/DC version) based on an innovative arc forming process developed by Hermann GmbH. In application, the SHARC process leads to higher welding speed with simultaneous improvement of the weld quality and reduction of the ancillary welding costs (less distortion, improved penetration, reduced annealing colours Gbodpswf Rgxsfx Aa Aek of the workpiece, less hardening of the transition edge zones and, if required, no need for filler materials). --> Technical data Welding current type: DC --> Mains voltage (50/60 Hz): 400 V --> Phases: 3 --> Setting range: 10 -320 A --> Electrode setting range: 25- 280 A --> Welding voltage: 22 V --> Open circuit voltage without HF: 70 V --> Open circuit voltage with HF: 90 V --> Primary power: 23 kVA --> Duty cycle 60%: 320 --> Duty cycle 100%: 260 --> Cooling type: F --> Protection class: IP 23

Condition: good (used), NM-420 W30 Banding Machine This brand new machine is based on proven Western designs. Year of manufacture: 2025. The device operates in manual or automatic mode. After inserting the material, the machine wraps it with tape, compresses, and seals it, creating an elegant package. Ideal for wrapping business cards, leaflets, and other materials. Gedpfxoywdq Ue Aa Aobk Technical specifications: Tape width: 30 mm Cycles per minute: 26 cycles/min Dimensions of the banded product: 400 x 200 mm The kit includes tapes and an instruction manual.

Year of construction: 2025, condition: new, functionality: fully functional, The universal laser marking system LAS 28 XLe from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes an integrated PC with Windows operating system and laser software. Optionally, the laser model LAS 28 XLe can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realized. Made in Germany Fiber laser 30W, 20 W or 50 Watt - Laser class 1 Gbsdpju Smd Esfx Aa Ask - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - marking software EZCAD in German / English - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - signal light for indication of operating status - max. component height approx. 300mm - electrically adjustable Z-axis - Integrated PC with Windows operating system - frame made of aluminum profile - air cooled - Door width approx. 700mm / door height(pass-through): 400mm - Connection 230V - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) - Weight: approx. 100 Kg

Condition: used, shaft length under head: 80 mm, thread length: 58 mm, GW 63 / GW 63SX flat-die thread rolling machines, various models, good condition, top-of-the-line electrical system EW Menn including vibratory feeder, Skako, and slide conveyor Gbsdpfewkqvqsx Aa Aok