Brushing machine

- Italy Basic 300

Condition: new, Year of construction: 2026, total length: 1,450 mm, total width: 800 mm, total height: 1,800 mm, overall weight: 500 kg, power: 4.75 kW (6.46 HP), FC 120 ZK Working capacity Ø 120x120 mm, Rcedst D D Nzepfx Amtef No. of belt stations (Z) 1, No. of brush stations (K) 1, Sanding belt, dimensions 120x1850 mm, Brush belt dimensions 120xØ200 mm, Sanding belt speed 20 m/s, Brush belt speed 15 m/s, Feed speed 12 m/s, Sanding belt motor per head (x1) 3 kW, Brush motor per head (x1) 1.5 kW, feed motor 0.25 kW, Total power 4.75 kW, Power consumption 12A, Rod suction connection per head Ø (2x) 80 mm, Dimensions 1450x800x1800 mm, Weight 500 kg

Condition: new, Year of construction: 2026, For professional and precise glue supply in dowel holes and back side grooves. Short introduction: • Always the same and right glue amount • No afterwards cleaning of the workpieces of too much glue is necessary • Easiest and minimal cleaning (1x week) of the gluing system (through cleaning program) • Glue cost savings • Ergonomic and light glue gun compared to squeezy glue bottles • Faster and more precise working compared to squeezy glue bottles Rcsdsdxz Tpjpfx Amtof

Year of construction: 2004, condition: ready for operation (used), Max. working width: 1000mm, feed rate: 5-20m/min, height: 2200mm, length: 4000mm, weight: 3.3t, with documentation, was maintained regularly. Rcedsi E Trpopfx Amtef

Condition: excellent (used), LOADER (BRIDGE-FRAME) WITH DOUBLE PICK-UP STATION Vacuum system (with its pump) Rodpfxofi Tg He Amtscf No. 2 Vertical supporting columns of the top supporting beam No. 1 Horizontal top supporting beam (where the carriage slide on) No. 1 Motorized sliding carriage with horizontal metal arms No. 2 Out-side rollers way (on gound) to in-feed pile of panels to the Loader Out-side motorized rollers table (which receives panels from the Loader) Separate electric and command panel Perimetral safety metal grids Working capacity (cycles/min) 16 (ca.) Min/Max panels thickness mm 10 / 50 (ca.) Min dimensions of the panels mm 250 x 320 (ca.) Max dimensions of the panels mm 1300 x 3000 (ca.) Total installed motor power Kw 30

Condition: good (used), Swivel Spindle Milling Machine, Table Milling Machine, Bench Milling Machine Rcsdpfsh Nvyzox Amtjf -Spindle adjustment: height and angle -Swivel: -3° to 45° -Drive: 4.5/5.5 kW -Speed: 3000/4500/6000/9000/12000 rpm -Feed apparatus Holz-Her 3 rolls -Useful shaft length: 100 mm -Spindle: Ø 30 mm -Max. Milling cutter: Ø 220 mm -Dimensions: 1540/1100/H1520 mm -Weight: 962 kg

Year of construction: 2004, condition: excellent (used), Four-side planer -max. planing width 23cm -max planing height 16cm -2 pulling rollers in the table Rjdpfx Amjhlp D Nstjcf -chromed table - smooth regulation of the feed speed -2 pulleys from the top in front of the lower head, additionally a roller apparatus for short elements - 4 spindles: lower 5.5kW, right 5.5kW, left 5.5kW, upper 7.5kw The machine is in very good condition, little used, with spiral heads on the bottom right and left, with a Terssa knife head on the top.

Condition: ready for operation (used), Year of construction: 2023, Load capacity: 1450/1125kg, load center: 600mm, lift height: 3200/4900mm, battery weight: 300-350kg, free lift: 900mm, mast height lowered: 2100mm, mast height extended: 4900mm, reach: 590mm, ground clearance under mast: 80mm, ground clearance at axle center: 50mm, track width: 1292mm, frame cross-section: 1058mm, front overhang: 655mm, wheelbase: 1120mm, rear overhang: 175mm, side shift: 80mm left / 80mm right, lost load thickness: 880mm, fork tilt back: 3°, fork tilt forward: 3°, min. turning radius: 1350mm, support arm height: 282mm, support arm length: 530mm, maximum speed: 6km/h, gradeability: 5%, battery capacity: 24V/270Ah, fork dimensions: 35x100x1070mm, front wheels (polyurethane): OD 200mm / width 50mm, rear wheel (solid rubber): outer diameter 250mm / width 75mm, AC drive motor: 24V / 2.5kW, AC pump motor: 24V / 5kW, rated power: 2.5kW, width: 1512mm, length: 1950mm, net weight without / with battery: 2800/3150kg, operating hours: 86h. An on-site inspection is possible. Rcjdpfx Amjw S Tyastef

Condition: good (used), Year of construction: 2011, functionality: fully functional, total height: 4,000 mm, inner dimension length: 6,500 mm, inner dimension width: 1,500 mm, inner dimension height: 2,200 mm, workpiece height (max.): 2,200 mm, workpiece length (max.): 6,500 mm, Equipment: cabin, Powder coating system for workpieces with dimensions: length 6500 mm, width 1500 mm, height 2200 mm. Rcjdpjvdlfzjfx Amtof

Condition: excellent (used), belt driven Flow rate 14500 m3/h Negative pressure 3091 Pa Motor power 22 kW Speed ​​2340 rpm Suction DM 500 mm Outlet DM 400 x 500 mm Dimensions L x W x H = 1800 x 1300 x 1250 mm Advise used machines: Rodpfeh Tfqhjx Amtocf • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: new, Type 1300-2S Rcedpfx Amem Dr Rgstef Working width 1300 mm Min.working length 400 mm Working thickness 2-80mm Grinding roller speed - Frequency control Feeding speed 5-20 m/min Total motor power 6.27 kW Transport dimensions 1700x2100x1400mm Weight 1200 kg Price 6100 Eur (EXW Jonava, Lithuania)