Faceplate 2013/13

700 mm KKG 8

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Rcjdpfx Agefg E Hpozjk Price on request.

Year of construction: 2018, condition: as good as new (ex-display), GHIBLI DHR 8 is the standalone system for thermal weeding: the 100% ecological solution against weeds thanks to the action of high temperature saturated steam. Thermal weeding has many advantages for the environment and health as: • it uses only water Redpfeg A Rhksx Agzock • it is safe, even in close proximity to sensitive places such as kindergartens, schools, hospitals. • its use does not require prior notification under the legislation in the field; • it is safe for exposed workers, people and animals, during and after the treatments;

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 450x320 saw band length 4250x34x1,1 mm band speed 40 + 80 m/min table height 845 mm saw band width 34 mm total power requirement 2,2 kW weight of the machine ca. 0,985 t dimensions of the machine ca. 1,4 x 2,0 x 2,2 m Double miter band saw, hydraulic semi-automatic, DGS 350/450 HA-I · miter left + right 60° without machine conversion · 34 mm saw blade width · Large material support turntable, ball bearings · To position the saw blade guides using a very wide linear guide · Strong, robust transmission · Large chipboards Rodsfgyicepfx Agzock · Infeed and outfeed roller Removable chip tray (disinfection) · Free-standing control panel, safe and ergonomic · Storage space for tapes, consumables · Cutting pressure regulator Feed regulator · Fully hydraulic vise Preload super fast (front loading) · Material height sensor (automatic cut start detection) Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise Optimum, material-independent cutting result through fine adjustment of the saw frame by means of: *Pressure Control Valve (Cutting Pressure Force) *Feed Control Valve (Speed) *Switch with pictogram, easy and clear to use

Condition: new, Year of construction: 2025, Patented mitering system Continuously adjustable cutting speed Hydraulic feed control Hydraulic lifting and lowering of the saw frame Hydraulic clamping of the material High-performance frequency-controlled band drive Swivel range 30° right / 45° left Cutting range in mm 45° left round 300, flat 300 x 300 90° round 410, flat 620 x 410 45° right round 360, flat 420 x 360 30° right round 300, flat 300 x 300 Remaining piece length without bundle clamping 60mm Recommended options: Micro spray device Laser light Redpfx Agjh S Nxpozeck Clamping pressure regulator Powered chip brush Manual lifting roller Setup elements

Condition: good (used), We offer steel tanks for the storage of almost all common liquid media. We have all available sizes from 1000 liters - 100,000 liters permanently in stock. No matter how your tank is to be equipped, we will implement your wishes and the official regulations at fair prices. Rodpfxogx E Uho Agzeck Whether you need an inner shell, 2K epoxy coating, exterior paint, fitting extensions or conversions, DEKRA approval, loading and transportation - we are the right partner for you.

Condition: good (used), Spectro CIROS CCD Water Analyser - height: 105cm - width: 150cm - depth: 75cm Good condition fully functional can be inspected and tested on site. Shipping also abroad. Inspection : Rsdpofiqn Usfx Agzeck Basically I would like to point out that in order to avoid misunderstandings, the article can be inspected and tested under power before purchase. Please ask questions before purchase to avoid any ambiguity. If you have general questions or would like to make an appointment for a viewing, I can be reached at any time at the telephone number below. Errors in the description and prior sale reserved. The value added tax is shown separately on my invoices. Dispatch with forwarding agent.

Condition: used, functionality: fully functional, power: 257.42 kW (349.99 HP), overall weight: 22,500 kg, Year of construction: 2009, machine/vehicle number: 08-12-987, Conrad Boxer 300 Combi – Flushing and Suction Drilling Rig Specifications Brand/Type: Conrad Boxer 300 Combi (Combi 300HD) Serial No.: 08-12-987 Year: 2009 Weight: 22,500 kg Rodoxrd Rhjpfx Agzsck Power: 280 kW Engine: Volvo, installed in 2024 TYPE TD 121 G - 350 PK Drill pipes: approx. 42 pcs, length 5 m, Ø 90/80 mm Flushing and suction drilling system

Condition: new, Year of construction: 2024, Electro hydraulic press 110 Ton Made in Italy The P110 MR is equipped with: 400 V 50-60 Hz immersed motor control unit. Pump for fast approach and return in 20 bar calibration. Adjustable pressure pump with handwheel to obtain the required power. Pressure relief valve with mechanical block to prevent overpressure. Pressure gauge (standard) that allows to calibrate with extreme precision the delivered power. The P110 MR is the only hydraulic press consisting of 2 laser-cut FE 510 monolithic structure uprights. without welding in the places of greatest stress This feature gives it extraordinary robustness. It is non-deformable and guarantees tight working tolerances. The P110 MR is equipped with a 30-litre tank and has a rapid descent speed of 1,400 mm/min. Weight : kg 1,100 Max pressure : bar 350 Max. flow rate : t. 110 Rapid flow rate :l/min 34 Slow flow rate : l/min 5 Inside shoulders : mm 1004 Rapid rod feed : mm/min 1.400 Slow rod feed : mm/min : 130 Voltage : V 400 Frequency :Hz 50-60 Power : kW 3 Max. absorbed current : A 7,3 Cylinder stroke : mm 300 Rodpfx Agjfh R N Dozock Cylinder diameter : mm 200 Stem diameter : mm 110 Piston descent speed : mm/sec 23 Tank capacity : litres 30

Condition: used, 5tSWF Krantechnik GmbH Rsdpfx Agsdc A R Tjzjck

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) Rcsdped Iipmjfx Agzjk • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens