Used Labelling machines for sale (5)

Condition: used, Year of construction: 1999, Functionality: fully functional, machine/vehicle number: 721 480-8-4-4-180, total width: 1,800 mm, total height: 2,400 mm, total length: 2,800 mm, Fully automatic labeling machine Krones Vinetta 721 480-8-4-4-180 Purchase price €53,700 (1999) Bwelev Img Ieq Rg Abel Output 8,000 bottles / h, bottle type Euro 0.5, Vichy 0.33 incl. lye control type 069

Year of construction: 2012, Condition: ready for operation (used), There are eight identical label dispense available, speed: 0-80m/min, output: 1000 label/ min, length: 700mm, width: 320mm, height: 500mm, including accessories. Bslqsflmc Ne Rg Abjwl

Condition: good (used), The AccuPlace Model 3065 is a film adhesive and label applicator, designed to place items of maximum dimension 76 mm x 165 mm with high accuracy and reproducibility. Notes - 1. 8 Nos. available 2. Price mentioned is Ex works. Any expenditures incurred for packaging and logistics would be charged extra to the buyer. Acknowledgement and disclaimer The goods the subject of this transaction were acquired by the seller for its own purposes and are no longer required. The sale of the goods is not part of the seller’s ordinary business and is part of a one-off sale to dispose excess spare parts that are no longer required and equipment that is surplus to our current requirements. The seller does not make any representation as to the purpose for which the goods might be utilised or their fitness for any particular purpose. The seller is not aware of any defect or faults in the goods (other than as may have been disclosed to the buyer). The buyer accepts the goods on the basis of their knowledge of any defects disclosed and the goods are otherwise provided ‘as is’ and without any warranty or representation as to their condition, except as expressly stated otherwise. No refunds will be offered if the goods are not suitable for your particular intended purpose, unless an express representation was made to say that the goods would be suitable for that specific purpose. Nothing in these terms is intended to exclude or limit any remedy that may be available to a consumer under the Australian Consumer Law to the extent that it applies to a particular sale of any goods. Bjlq Rgsvm Epfj Abowl

Condition: new, Year of construction: 2020, Guildolin Girotto GD 301D - automotive parts /labelling systems reel-to-reel / reeel-to-sheet machine The machine is NEW! Available immediately. - CONTINUOUS AUTOMATIC MECHANICAL-ELECTRONIC DIE- CUTTING MACHINES MOD. GD 301D - 10 tons of power – cutting plates 320 x 320 mm Useful cutting area 290 x 290 mm - fixed run 40 mm - electronic variator of speedy from 30 to 150 strokes per minute - KD/FM SYSTEM: triple unwind, the upper shaft is an unwind and it can be used as friction or motorised, the middle shaft can be used as motorised rewind or friction unwind, lower shaft is an unwind and it can be used as friction or motorised – according to the requirements. The motors at variable speed from digital inverter are placed on slides and the KD/FM group is assembled on the machine # n.3 photocells of end material # n.2 photocell of automatic feed # n.3 pneumatic expansion shafts diam.76mm with valve in the head # n.3 electronic brakes managed by ultrasonic sensors which detect the diameter of the roll of material and adjust the power of the brakes, managed by potentiometer. - guides on rolls on the inboard side - feeder rolls system on the inboard side before the change liner - the feeder rolls are covered in silicone rubber and motorized - KR SYSTEM: upper single motorised rewind controlled by inverter assembled on the machine and complete with 1 pneumatic expansion shaft diameter 76 mm with valve in the head for inflation - KF SYSTEM: upper friction unwind with guides and roll assembled to the machine and complete with n.1 pneumatic expansion shaft diam.76mm with valve on the head for inflation. N.1 electronic brake managed by ultrasonic sensor which detects the diameter of the roll of material and adjust the power of the brake, managed by potentiometer. - feeder rolls system on the inboard side after the change liner - the feeder rolls are covered in silicone rubber and motorized Bjlq Rg Ajuv Hnxjbswl - touchers at rolls placed before and after the cutting plate - extractable rectified steel plate support cutting-knife and counter cutting-knife - the plate support cutting-knife is with guides at swallow tailed for a speed and easy change of the cutting-knife - K2 SYSTEM : scrap separator with transversal bar and roll covered with anti-adherent material - KR SYSTEM : upper single motorised rewind controlled by inverter assembled on the machine to rewind the waste removed by the K2 system complete with n.1 pneumatic expansion shaft diameter 76 mm with valve in the head for inflation. this shaft is equipped also with frontal mechanical friction for a lightly adjustment. - K3 SYSTEM: placed between the cutting head and the outboard feeder rolls group : # pneumatic group of evacuation pieces synchronized and run by the machine controller. The evacuation position is adjustable on the X. Y. Z. axes. This system is complete with support brackets for the counter matrix. - TL SYSTEM: longitudinal cut system with 5 razor blades and adjusting of the position of the blades on their axe - feeder rolls system on the inboard side after the TL system - the feeder rolls are covered in silicone rubber and motorized - CTT SYSTEM : passage of material 320 mm - pneumatic cutter assembled on machine for the transversal cut, heavy version for cutting materials with max thickness 15 mm, complete with motorized feeder rolls for the correct positioning of the material under the blades

Year of construction: 1994, Condition: ready for operation (used), Format: 0.2/ 0.7/ 1l. Bwjlq Rg Aegquviebjl