Horizontal storage system

BARGSTEDT TLF 420/39/15

Condition: used, Year of construction: 2017, power: 20 kW (27.19 HP), edge thickness (max.): 12 mm, feed rate X-axis: 20 m/min, The machine has the following configuration: Pre-milling unit End-capping unit Number of motors in end-capping unit: 2 Kedjzmtldopfx Adksdp Rough milling unit, top and bottom Number of motors in rough milling unit: 2 Edge rounding unit Number of motors in edge rounding unit: 2 Edge trimming unit Glue application unit Edge finishing unit Number of motors in edge finishing unit: 2 TECHNICAL DETAILS Workpiece processing Min. board thickness: 8 mm Max. board thickness: 60 mm Min. edge thickness: 0.4 mm Max. edge thickness: 12 mm Max. feed rate: 20 m/min MACHINE DETAILS Total connected load: 20 kW EQUIPMENT Preheating lamps for workpiece sides Edge roller magazine Glue reservoir for EVA hot melt adhesive Spray unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents, which are for descriptive purposes only. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7981

Condition: used, Year of construction: 2013, power: 17.1 kW (23.25 HP), number of axes: 4, working width: 1,320 mm, milling spindle speed (max.): 24,000 rpm, working length: 2,500 mm, TECHNICAL DETAILS Working area, X-axis: 2,500 mm Working area, Y-axis: 1,320 mm Travel, Y-axis: 1,900 mm Max. panel thickness: 170 mm Work table: Cantilever and rail table Number of controlled axes: 4 Travel speed, X-axis: 80 m/min Travel speed, Y-axis: 80 m/min Travel speed, Z-axis: 20 m/min Drilling unit Number of drilling units: 1 Position of drilling unit: top Vertical drilling spindles: 10 Horizontal drilling spindles, X-direction: 4 Horizontal drilling spindles, Y-direction: 2 Total number of drilling spindles: 16 Milling spindle Number of milling spindles: 1 Position of milling spindle: top Controlled axes: 4 Automatic tool changer: yes Motor power: 13 kW Speed: 24,000 rpm Grooving unit Number of grooving units: 1 Position of grooving unit: top Design: fixed, for grooving in the X-direction Max. tool diameter: 120 mm Motor power: 1.7 kW Speed: 7,500 rpm Number of tool magazines: 2 Tool magazine, rear: 12 slots Tool magazine, side: 10 slots Total number of tool change slots: 22 MACHINE DETAILS Machine programming software: BiesseWorks Number of vacuum pumps: 1 Suction capacity per pump: 90 m³/h Total connected load: 17.1 kW EQUIPMENT CE marking Protective structure for machining units with safety sensors Safety system: front safety mats 4 consoles with suction cups for workpiece clamping 1 drilling unit, top 1 milling spindle, top 1 fixed grooving unit, top, for grooves in the X-direction 1 rear tool magazine with 12 slots 1 side tool magazine with 10 slots 1 vacuum pump Front safety mats The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents with a descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8359 Kdjdpezmtlkjfx Adksp

Condition: used, Year of construction: 2010, power: 30 kW (40.79 HP), cutting width (max.): 3,800 mm, controller model: POWERCONTROL, cutting length (max.): 2,200 mm, Equipment: scorer, TECHNICAL DETAILS Max. panel width: 3,800 mm Max. panel length: 2,200 mm Min. cutting height: 6 mm Max. saw blade overhang: 130 mm Number of tables: 3 Number of grippers: 7 Gripper arrangement: On the sliding stop Max. feed rate: 90 m/min Sawing unit Number of saw carriages: 1 Positioning: NC-controlled Max. tool diameter: 480 mm Motor power: 18 kW Kedpjzmtnljfx Adksdp Scoring unit Positioning: NC-controlled Max. tool diameter: 200 mm Motor power: 2.2 kW MACHINE DETAILS Control system: POWERCONTROL Machine programming software: CADMATIC 4 Total connected load: 30 kW EQUIPMENT CE marking Barcode label printer The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents with a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7875

Condition: used, Year of construction: 2006, power: 25 kW (33.99 HP), cutting height (max.): 110 mm, cutting width (max.): 4,300 mm, cutting length (max.): 4,300 mm, TECHNICAL DETAILS Max. panel width: 4,300 mm Max. panel length: 4,300 mm Min. cutting height: 3 mm Max. cutting height: 110 mm Max. saw blade overhang: 125 mm Feed and Grippers Number of grippers: 9 Number of grippers on the sliding stop: 9 Max. feed rate: 80 m/min Max. feed rate of the saw carriage: 120 m/min Saw Carriage Kdodpfx Adezmtn Ssksp Max. tool diameter: 450 mm Motor power: 18 kW Speed: 2,870 rpm Scoring Unit Design: Postforming scoring unit Max. tool diameter: 340 mm Motor power: 2.2 kW Speed: 2,880 rpm MACHINE DETAILS Control system: Windows XP Machine programming software: CADMATIC 3 Total connected power: 25 kW EQUIPMENT CE marking 4 front support tables 9 grippers on the sliding stop Postforming scoring unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8206

Year of construction: 2007, condition: used, Auction of a drilling line with the following components: PRIESS EIN-Igel (Vertical storage system) PRIESS BAT-DTW-CNC PRIESS BAT-DTW-CNC PRIESS BMA DLS-CNC WANDRES CVT 05/1000 PRIESS Conveyor system TECHNICAL DETAILS Vertical storage system Max. panel width: 500 mm Max. panel length: 1,500 mm CNC drilling machine Machining process: Drilling Working area X-axis: 2,500 mm Working area Y-axis: 800 mm Max. panel thickness: 26 mm Number of drilling units: 4 Total number of drilling spindles: 88 Drilling unit 1 Position: Top Vertical drilling spindles: 23 Drilling unit 2 Position: Top Vertical drilling spindles: 23 Drilling unit 3 Position: Bottom Vertical drilling spindles: 12 Drilling unit 4 Position: Bottom Vertical drilling spindles: 20 CNC drilling and dowel insertion machine (Priess BAT-DTW-CNC) Machining process: Drilling and insertion Working area X-axis: 2,500 mm Working area Y-axis: 800 mm Number of working areas: 1 Total number of drilling spindles: 49 Number of drilling units: 4 Drilling unit 1 Position: Top Horizontal drilling spindles in X-direction: 8 Drilling unit 2 Position: Top Horizontal drilling spindles in X-direction: 17 Drilling unit 3 Position: Top Vertical drilling spindles: 12 Drilling unit 4 Position: Top Vertical drilling spindles: 12 Insertion unit Number of insertion units: 1 Number of injectors: 10 Number of hoppers: 1 Insertion material: Wooden dowels CNC drilling and insertion machine (BMA DLS-CNC) Machining process: Drilling and insertion Working area X-axis: 2,500 mm Working area Y-axis: 800 mm Number of controlled axes: 3 Main electric spindle power: 4.4 kW Number of milling spindles: 3 Number of insertion units: 2 Kdedpfxozmtpvs Adkjp Milling spindle 1 Position: Top Number of controlled axes: 3 Motor power: 4 kW Milling spindle 2 Position: Top Number of controlled axes: 3 Motor power: 4 kW Milling spindle 3 Position: Top Number of controlled axes: 3 Motor power: 4 kW Grooving unit Position: Top Insertion unit 1 Number of injectors: 1 Number of hoppers: 1 Insertion unit 2 Number of injectors: 1 Number of hoppers: 1 Brushing machine Max. working width: 800 mm Max. machining width: 800 mm Max. machining length: 2,500 mm Brush diameter: 160 mm Roller conveyor Max. panel width: 800 mm Max. panel length: 2,500 mm Panel feed: Motorized belt

Condition: used, Year of construction: 2004, saw blade diameter: 180 mm, tool diameter: 450 mm, Equipment: scorer, TECHNICAL DETAILS Sawing carriage Max. saw blade overhang: 125 mm Number of grippers: 11 Max. feed rate: 80 m/min Max. tool diameter: 450 mm Motor power: 21 kW Scoring saw Max. saw blade diameter: 180 mm Motor power: 2.2 kW Max. feed rate: 150 m/min Kdedpfx Adjzmtm Ueksp EQUIPMENT Lifting table Scoring unit Barcode label printer The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents, which are of a descriptive nature. The buyer has the right to inspect the goods before collection and is responsible for the installation, securing, and use of the machine at the destination. External reference: 6645

Condition: used, Year of construction: 2014, edge thickness (max.): 12 mm, feed rate X-axis: 18 m/min, TECHNICAL DETAILS Workpiece Dimensions Min. panel height: 10 mm Max. panel height: 60 mm Min. panel width: 70 mm Min. edge thickness: 0.4 mm Max. edge thickness: 12 mm Max. feed rate: 18 m/min Feed and Guidance Pressure with idler rollers Panel support guides Unit for Panel Processing Pre-milling unit Automatically timed engagement Motor power: 2.2 kW Edge Gluing Kdodpezmtivjfx Adkop Edge roller magazine Glue reservoir for EVA hot melt adhesive Pre-melter for EVA hot melt adhesive Hot air system: AIRTEK Number of pressure rollers: 4 NC-controlled Edge Processing Units Number of edge processing units: 7 End-capping unit Number of motors: 2 Motor power: 0.35 kW Fine milling unit for flush trimming and rounding Number of motors: 2 NC-controlled Motor power: 0.55 kW Corner rounding unit Manufacturer model: WD60 Motor power: 0.35 kW Rough milling unit Motor power: 3.5 kW Edge trimming unit NC-controlled Glue application unit Polishing unit Number of motors: 2 Motor power: 0.18 kW MACHINE DETAILS Control and Safety Machine programming software: PowerControl PC20 Safety standard: CE marking Electrical Data Total connected load: 22 kW EQUIPMENT Pre-milling unit Edge roller magazine Glue reservoir for EVA hot melt adhesive Pre-melter for EVA hot melt adhesive Hot air system AIRTEK 4 pressure rollers End-capping unit Fine milling unit for flush trimming and rounding Corner rounding unit WD60 Rough milling unit Edge trimming unit Glue application unit Polishing unit Spray unit Machine programming software PowerControl PC20

Condition: used, Year of construction: 2008, power: 41 kW (55.74 HP), edge thickness (max.): 3 mm, controller model: ICOS OPEN, The machine has the following configuration: Pre-milling unit Manufacturer model: R3 L20 Engagement control: Automatic, time-controlled Motor power: 4 kW Kodpfx Ajzmtkasdkjdp Speed: 9,000 rpm Edge processing Number of edge processing units: 10 Crosscut saw unit Manufacturer model: 8.42/39/B Number of motors: 2 Motor power: 0.6 kW Speed: 12,000 rpm Flush trimming and rounding unit Manufacturer model: 08.055 Number of motors: 0.6 (?) Motor power: 1 kW Speed: 12,000 rpm Corner rounding unit Manufacturer model: 08.342 Number of motors: 2 Motor power: 0.66 kW Speed: 12,000 rpm Scraper blade unit Manufacturer model: 08.50 Belt sanding unit 1 Manufacturer model: 08.62 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 2 Manufacturer model: 08.062 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 3 Manufacturer model: 08 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 4 Manufacturer model: 08.617-2 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 5 Manufacturer model: 08 Processing unit 10 Manufacturer model: 08.190 Motor power: 4.5 kW Speed: 9,000 rpm TECHNICAL DETAILS Workpiece dimensions Max. panel height: 60 mm Min. panel length: 130 mm Min. panel width: 65 mm Edge material Min. edge thickness: 0.4 mm Max. edge thickness: 3 mm Feed Max. feed rate: 30 m/min Pressure: Rubber belt Number of panel sizing/milling units: 1 MACHINE DETAILS Control system: ICOS OPEN Total connected power: 41 kW EQUIPMENT Number of panel sizing/milling units: 1 Lamps for preheating the panel side Edge roller magazine with 2 positions PUR pre-melting unit Pressure roller set with 5 pressure rollers Spraying unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at its destination. External reference: 5657

Condition: used, Year of construction: 2004, number of axes: 4, controller model: POWERCONTROL PC85, working width: 1,220 mm, milling spindle speed (max.): 24,000 rpm, working length: 3,250 mm, TECHNICAL DETAILS Working area X-axis: 3,250 mm Working area Y-axis: 1,220 mm Number of working areas: 2 Kdsdpjzmtl Rsfx Adkop Table system: Pod-and-rail table Number of vacuum pod holders: 6 Number of controlled axes: 4 Number of drilling units: 1 Number of milling spindles: 1 Number of grooving units: 1 Drilling unit Position: top Vertical drilling spindles: 12 Horizontal drilling spindles in X-direction: 4 Horizontal drilling spindles in Y-direction: 2 Total number of drilling spindles: 18 Milling spindle Position: top Controlled axes: 4 Motor power: 12 kW Speed: 24,000 rpm Cooling: Liquid cooling Tool change: automatic Grooving unit Position: top Design: fixed, for producing grooves in the X-direction Maximum tool diameter: 100 mm Motor power: 2.2 kW Speed: 7,500 rpm Number of tool change stations: 16 Tool magazine on the machining head: 8 slots Tool magazine on the rear of the machine: 8 slots MACHINE DETAILS Control system: POWERCONTROL PC85 Programming software: WOODWOP 5 Main spindle power: 12 kW Total connected power: 22 kW Vacuum pump capacity: 100 m³/h EQUIPMENT CE marking Pod-and-rail work table 6 vacuum pod holders Vacuum pump Automatic tool changer 2 tool magazines, each with 8 slots Protective device for machining units with safety sensors Front safety mats Liquid cooling of the milling spindle The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents with descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing and use of the machine at the destination. External reference: 7716

Condition: used, Year of construction: 2008, power: 36 kW (48.95 HP), cutting height (max.): 105 mm, cutting width (max.): 4,400 mm, cutting length (max.): 2,200 mm, Equipment: scorer, TECHNICAL DETAILS Kdsdpfxozmtnxs Adkep Max. panel width: 4,400 mm Max. panel length: 2,200 mm Max. cutting height: 105 mm Thin panel feed: Yes Post-forming process: Yes Gripper system Number of grippers: 10 Flexible, NC-positionable grippers: Yes Grippers on the sliding stop: Yes Sawing unit Main saw blade overhang: 120 mm Max. saw blade overhang: 120 mm Max. tool diameter, main saw: 450 mm Scoring unit: Yes Post-forming scoring unit: Yes Max. tool diameter, scoring saw: 300 mm Max. feed rate: 130 m/min MACHINE DETAILS Control system: Windows Machine programming software: OSI Total connected load: 36 kW EQUIPMENT CE marking Tilting table with 4 tables Saw carriage 1 Barcode label printer Zebra S4M The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8409