Press brakes Baykal APH 31220 1994

Baykal APH 31220

Condition: excellent (used), Year of construction: 1993, spindle bore: 118 mm, turning diameter over bed slide: 635 mm, turning diameter over top slide: 390 mm, turning length: 2,000 mm, total length: 4,170 mm, total width: 1,960 mm, total height: 1,800 mm, spindle speed (max.): 1,250 rpm, swing diameter over cross slide: 390 mm, bed width: 480 mm, overall weight: 5,200 kg, Centre lathe Colchester 600 - MAGNUM 1250 MACH-ID 9464 Make: Colchester 600 Type: MAGNUM 1250 Year: 1993 FAGOR 2 Axis Dro Feed all directions Conical turning attachment DBC Turning Length: 2000mm Swing over bed Ø: 635mm Swing over cross slide Ø:390mm Swing in the gap Ø: 900mm Gap length: 300mm Spindle bore: 118mm Spindle power: 22kW Bed width: 480mm Tailstock spindle Ø: 95Ø Stroke pinole: 190mm Ncsdpfxeyuwwhe Akqer Spindle taper: 6Mk Speeds / ranges: 1250Rpm Length: 4170mm Width: 1960mm Height: 1800mm Weight: 5200kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2008, Technical details: bore capacity in steel (diameter): 40 mm throat: 350 mm bore stroke: 120 mm bore capacity in cast iron: 60 mm spindle taper MT: MK 4 spindle throat: 350 mm spindle speed:: 50 - 1450 / 18 step U/min feed: automatisch/manuell mm/U Distance spindle/table max.: 25 - 705 mm table clamping surface:: 430 x 430 mm drill table adjustment: 680 mm column diameter: 150 mm distance spindle center to floor plate:: 1210 mm total power requirement: 1,6 kW weight of the machine ca.: 350 kg dimension machine xH: 0,95 x 0,55 x 2,3 m Height-adjustable table(swivel and tilt adjustable ) Table can be swiveled 45° left/right and rotated 360° around the column Thread cutting up to M24 Coolant system A vise is mounted, and a threading device is included with this machine. Ncsdpjviqybjfx Akqor *

Year of construction: 1979, condition: used, throat: 22/29 mm drive motor: bei 380 V ca. 0,55 kW space needed: 450 x 500 x 560 mm weight: ca. 6,5 kg Ncedezif Sjpfx Akqsr pressure power: 30 kN

Condition: good (used), Year of construction: 1998, functionality: fully functional, pressing force: 35 t, working width: 2,000 mm, pressure 35to max. bending length 2000mm arrester behind Nodpfowagykjx Akqscr drive capacity 4,5 kW weight 3000kg

Condition: new, maximum load weight: 49,000 kg, overall weight: 60,800 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Ncodpfxsh Etf Re Akqer Loading area in extendable version: -Loading surface in extendable version with rear bevel of approx. 1,000 mm x 8° -5 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Removable two-part ramps: -A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Seat posts: -JOST fifth wheels (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles, two axles rigid two axles self-steering, air-suspended, with drum brake, with lifting/lowering function The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -axle tool -235/75 R 17.5 tires Brake system: -brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Coating: -First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Electrical system: -Electrical system in accordance with EU regulations, 24 volt ASPÖCK-NORDIK lighting (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon -Cover plates to bridge the gap between ramps and cargo bed -White reflector tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for one 20ft, 2x 20ft or one 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Lift axle on the front axle with controls -Square climbing rails 20 x 20 mm -BEKAMAX central lubrication system -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm

Condition: excellent (used), Year of construction: 1980, Horizontal gear hobbing and threading machine for gears, splined shafts, worm screws, threads, and pinions up to 5 meters in length, complete with 3 milling heads models APFW, APGS, APG, set of gears, various steadies, and indexing device. Ncedpfx Aeyba Rwekqjr

Condition: used, Year of construction: 1998, turning diameter over bed 0400 mm turning diameter over slide rest 260 mm turning length 1500 mm centre height 200 mm centre distance 1500 mm spindle bore 50,8 mm speeds 20- 3150 U/min Nedpfxexp Rzbs Akqecr feeds longitudinal slide 0,01 - 3,24 mm/U feeds cross slide 0,005- 1,62 mm/U weight of the machine ca. 2 t dimensions of the machine ca. 3,35 x 1,4 x 1,9 m voltage 400 V connected load 7,7 kVA With chuck, Multifix toolholder and digital readout.

Condition: used, Year of construction: 2004, The bending press is made in 2004 in Turkey, in the ERMAKSAN factory. The folding press is in good condition, sold with tools. The machines are connected and can be tested and inspected. Specification: Model. Year: 2004 Working length: 2600 mm Bending capacity: 80 T Axles: Y1-Y2-X Tools: Yes Weight: 5.5 T Motor: 7,5 kW If you have any further questions, we will be happy to answer them. Ncedpfx Akjq U Sdroqsr

Year of construction: 1978, condition: used, pressure 100 t throat 380 mm stroke 400 mm power capacity 22 kW dayligth 600 mm ram surface 600x500 mm Njdpfolp U Dpjx Akqocr table surface area 720x600 mm weight of the machine ca. 9 t

Condition: new, Working width: 4010 mm Bending capacity (St42): 2.0 mm Bending angle adjustment from/to: 0 - 135° Adjustability of the bending beam: 25 mm Hydraulic motor drive power: 2.2 kW Weight, approx.: 5000 kg Dimensions LxWxH, approx.: 5600 x 1750 x 2050 mm The torsion-free, heavy machine body is designed for very high loads. This machine therefore guarantees a high and consistent quality of your bent products. The integrated tool holder makes it easy to change tools. This means that the AKB folding machine can be easily adapted to your future requirements. Model description: - MIKRA Bending Control positioning control type "M15S" (alternative control variants optionally available) - Solid and torsion-free welded steel construction - Bending beam adjustment from 0 to 135 - Hydraulically driven upper and bending beam - Clamping pressure of the upper beam can be adjusted centrally from the front on both sides - Crowning of upper, lower and bending beam manually adjustable - Segmented upper beam / upper beam inclination 45° Ncjdep Dufzjpfx Akqjr Scope of delivery: - Manual backgauge 600 mm - Tool set: Segmented upper tool Lower beam rail Bending beam rail 25.0 mm - Manual gap adjustment - 3-way foot switch - Control valve for setting the hydraulic pressure from the front - Foot pedal with three functions, handle and emergency stop button - Light barrier - Oil filling - Documentation - CE