Suction and filtration unit

CATTINAIR

Condition: good (used), Year of construction: 2019, machine/vehicle number: 9501441040100301, Offer 24469 Welding mist filter system with spark pre-separator + extraction arms Hnjdpsuwl Duefx Ad Djw Technical data - Vertical version for filtering welding fumes + grinding dusts, - Welding fume class "W 3" - Suitable for filtering welding fumes from steels with - chromium + nickel content of over 30% - Exhaust air can be discharged into the work area, e.g. for heating or outside - can be - TEKA control unit - Air volume flow up to approx. 4000 m³/h - Max. static pressure up to approx. 3000 pa - 4 BIAM filter cartridges - Pulse Jet cleaning system with separation efficiency > 99 % - Separate control cabinet - Connection 400 V / 4 kW - Space requirement Filtercube approx. W 850 x H 3150 x D 850 mm - Weight approx. 380 kg - Separate spark pre-separator make TEKA type FVS 4000 - 6000 - Space requirement spark separator W 850 x H 1650 x D 950 mm - 3 articulated extraction arms - Pipework

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Hnsdpfjwp Rqfox Ad Dow Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price: 30,000.00 EUR (VAT is not included)

Year of construction: 2023, condition: new, Always in stock, as left and right version with motorized cleaning. Riedex DM-200 Motor power 4,0 kW Hjdpfx Asku Aibod Donw Ready to plug in. Packed on pallet! Ready for shipment. Alternatively also available with JET cleaning. Many different designs possible ..... - with rotary valve (if desired with underframe) - with briquetting press etc.

Condition: good (used), Ceia THS Metal detector checkweigher Hnsdstt D S Uepfx Ad Djw Stainless metal detector checkweigher, aperture 340mm x 100mm, checkweigher platform 420mm x 290mm, with blow off reject into reject bins, with printer, mobile, 1Ph

Condition: used, Holz Her Auriga 1308 FÜ + PU Compact design - Edge thickness 0.4 - 8 mm PLC screen control Edge-Control PPC 221 color display Pre-milling unit for edge preparation before the gluing section Fully automatic edge magazine for both coil and strip material Gluing unit GLU JET cartridge + PU bonding - multi-system Adhesive application via nozzle technology Workpiece height 6-65 mm Automatic glue height adjustment Pressure unit 1912-3 pneumatic End trimming unit 1918 pneumatic for coil and strip material up to 8 mm edge thickness With pneumatic adjustment from 0-10° mitre for trimming saws Milling unit for flush trimming 8 mm, corner rounding, bevel trimming at 15° via control panel Profile trimming unit 1832 pneumatic, rounds corners up to 3 mm edge thickness in throughfeed Scraper unit for bevels and radii Flat scraper unit – finish Spraying device – PU Complete set of DIA tools included Machine is WORKSHOP-REFURBISHED in TOP CONDITION Available from stock in Lieboch Hodpsxrr Uzsfx Ad Dsnw

Condition: new, Vacomats are mobile dust extractors that extract large quantities of dust and chips in the smallest of spaces. in the smallest of spaces. These clean air extraction systems (vacuum) for indoor installation can be installed indoors as single or multi-machine machines for air volumes of up to 10,000 m³/h can be used. Manufactured according to the new EU standard EN 16770, they are particularly suitable for wood processing operations in which special safety requirements due to the risk of dust explosion. Materials of dust explosion class St1 are suitable. The Vacomaten XPe filters are cleaned purely electro/mechanical via an efficient vibration motor, which - as soon as all machines are switched off - starts Hnedpfx Adsu T Dv Es Dow starts automatically. It is controlled via the the woodworking machine by means of potential-free contacts. The control of the motorized jogging is included in the scope of delivery. Supplied without coils Motorized filter regeneration, mobile, Suction side on right or left, can be reassembled, Height reduction possible for transportation ----- Technical data ----- Extraction nozzle Ø: 200 mm, Volume flow: 2,495 m³/h, Nominal volume flow: 2,262 m³/h, max. negative pressure: 2,000 Pa, Filter area: 14.5 m², Residual dust content: < 0.1 mg/m², Number of bags: 3 pieces, Motor: 4.0 kW, Dimensions (LxWxH): 2,645 x 900 x 2,130 mm, Weight: 500 kg, Sound pressure level: 73 dB(A), Dust class: M incl.: an attached control cabinet

Year of construction: 1991, condition: good (used), Dust extraction,welding fume extraction,filtering,self-cleaning filter,pneumatic,vacuum dust collector,absorber for plasma,laser,sandblasting and all kinds of dry dust. Donaldson Torit model: 3DF18 Cyclo - with pre-separator Cartridge filter cartridges cleaned pneumatically with pulses of compressed air during operation, thus high efficiency of the device. The fan is located behind the filter on the clean side, which reduces the risk of explosion to a minimum. Cartridge filter cartridges. 7.5 Kw fan Hnsdpjmrm Rajfx Ad Dew Capacity 6000 m3/h Underpressure 3000 Pa Filtration area 378 m2 Inlet diameter - 350 mm Ultra WEB filter cartridges 18 pcs.

Condition: new, SCHUKO Vacomat 140/160 XPe clean air extraction system - Exhibition unit - Filter generation motorized, mobile, Hjdeu R Szyspfx Ad Dsnw extraction side right or left, can be remounted ----- Technical data ----- Test mark: H3 / BGHM HO 193023, Extraction nozzle Ø: 1 x 140 / 160 mm, Nominal volume flow: 1,447 m³/h, max. negative pressure: 2,200 Pa, Filter area: 9.5 m², Residual dust content: < 0.1 mg/m³, Number of bags: 1 piece, Motor: 2.2 kW, Dimensions (LxWxH): 1,665 x 900 x 1,980 mm, Weight: 306 kg, Dust class M: AWN 16 - new exhibition machine -

Condition: new, functionality: fully functional, Year of construction: 2022, load capacity: 2,000 kg, lifting height: 6,350 mm, fuel type: electric, mast type: triplex, fork length: 1,150 mm, color: yellow, fuel: electricity, Brand: Aisle-Master Type: 20NE Capacity: 2,000 kg Year of construction: 2022 Hnsdpfx Ajt Dwbdjd Dew Lifting mast: Triplex Lifting height: 6350 mm

Condition: ready for operation (used), A Scheuch extraction filter and heat recovery system with a tower for outdoor installation is available. Air flow rate approx. 14300m³/h, fan power 20kW. Including fill level monitoring of the filter tray, pressure surge cleaning of the filter hoses, maintenance platform with access ladder at the filter, dry riser at the filter, control of exhaust air (summer) or return air into the hall (winter) at the control cabinet, heat recovery with reheating coil in the hall, air ducts for air distribution. Available from November 2024. Documentation available. On-site inspection is possible. Hnodpfetpx Emox Ad Djw