Fiber Laser HD-F 6020 6kW

DURMA FIBER LASER 6m x 2m | 6 kW

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function Kdodeh Hm Tzjpfx Aqpjl -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck -One Locking point approximately every 1,000 mm on the extension -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: new, Year of construction: 2026, UNIBOHRFIX 100 H Fully automatic drilling machine, measuring length 6000mm Item No. 6020 With the fully automatic drilling machine UniBohrFix 100, your material is positioned on the X-axis at the desired position, clamped and drilled. All you have to do is press the start button. Round tubes, rectangular tubes and angle profiles, as well as flat and solid materials, can be conveniently pneumatically clamped in the horizontal gripper of the positioning system. After simply entering the X values ​​and calling up a program that has already been written, the machine works completely independently. The Y-axis can be adjusted by the operator using a handwheel with a digital display. Advantages • A sequence of holes is automatically executed at precise intervals. • Potential operator errors are drastically reduced. • Programming takes just a few minutes. • Very good value for money. • Significant reduction in labor force Fully automatic execution Measuring length: 6,000 mm Total length: 13,500mm NC 1-axis control Pneumatic vice (span 200 mm) Minimum quantity spray unit with holder and spray nozzle Drill: Unimax 3T AV (for technical data see data sheet) Kdsdefu Itbjpfx Aqpsl anti-rotation device motorized height adjustment tapping device NC positioning system PD 200p Feed force 200 kg Positioning according to absolute and incremental dimensions possible Carriage with DC servo motor and encoder Trolley with 12 ball bearings Pneumatic stop clamping with high holding power Steel guide rail with precision toothed rack Steel carrier profile to protect against dirt Infeed and outfeed material roller conveyor RD-200/4 Length: 6,000 mm / 7,000 mm / load capacity 200 kg/m / rollers adjustable in height / mounting bracket / roller width 407 mm / insert plates / struts / roller diameter 50 mm / steel rollers

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 Kodjhlz R Sspfx Aqpsdl -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: excellent (used), Year of construction: 2020, operating hours: 14,000 h, functionality: fully functional, machine/vehicle number: 3294, type of input current: three-phase, power: 90 kW (122.37 HP), input voltage: 400 V, We are selling press line from Nova pellet, 2019 production and 2020 first year of production start. -Pellet press N-MIDI 90 KW 14.000 hrs(very good and daily maintaince, 2026 new rollers and die)-2019 year -Transporting vertical elevator ca 10m height-2019 year Kedpfx Aqjwahhcopedl -Cooling tower N-CO700-2019 year -Control cabinet-NEW UNUSED For aditional price we are selling heavy duty hammermill Miller M16(37kW electric engine)-NEW UNUSED-25.000€ netto We are selling only items above(without cyklon, filters etc.)! Line is in very good condition and had very good daily maintaince. For further informations, please write or call on our contact.

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm Kedpfjhlnzksx Aqpedl slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: ready for operation (used), Year of construction: 2015, - USED - FIBER LASER CUTTING MACHINE WITH PALLET CHANGER and LOADING/UNLOADING SYSTEM X-AXIS TRAVEL: 4000 mm Y-AXIS TRAVEL: 2000 mm Z-AXIS TRAVEL: 115 mm Kjdpfx Aqjxqtx Sjpjdl RAPID FEEDS X-Y-Z: 245 m/min WORKING AREA: 4000 x 2000 mm ADMITTED LOAD ON TABLE: 1250 Kg SOURCE: TRUDISK 5001 ; 5000 W WEIGHT: 15000 Kg OVERALL DIMENSIONS: 10900 x 5700 x 2400 mm NOTE: LIFT MASTER COMPACT LOADING/UNLOADING SYSTEM

Condition: new, Year of construction: 2025, operating hours: 1 h, functionality: fully functional, travel distance X-axis: 4,000 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 1,000 mm, controller manufacturer: STYLE CNC Machines, number of slots in tool magazine: 24, motor manufacturer: FANUC, Delivery after consultation Ref: 24F048 Year of construction: 2025 Condition: Showroom Specifications: Kdjdpfx Aqew Ty S Sjpol - X-axis: 4000 mm - Y-axis: 1000 mm - Z-axis: 1000 mm - 26 kW (S6) main motor - 8000 rpm - BT-40 - Automatic tool changer (24 positions) - Remote service (IXON) + network connection - Stronger coolant pump incl. spray gun - Upgraded to the latest STYLE software available

Condition: used, Year of construction: 2004, Cast epoxy resin - dry - 3 phase distribution transformer, manufacturer TESAR Italy, year of manufacture 2004, power 1600kVA, voltage ratio 20(2x±2.5%)/0.4kV, AN-AF (forced ventilation, permanent overload 30%), Dyn11, uk=6%, IP00, standard losses, functional, complete documentation and rutine test report, total 2 pcs. Kodpfswpb Emex Aqpsdl

Condition: used, Year of construction: 2023, functionality: fully functional, travel distance X-axis: 14,000 mm, travel distance Y-axis: 4,500 mm, travel distance Z-axis: 1,900 mm, RepairFIT by Dornhöfer The Difference. Installation & Commissioning Included! Year of manufacture of the machine: 2023 Capacities / Travel distances: Longitudinal (X): 14,000 mm Vertical (Y): 4,500 mm (*5,076.5) Cross (Z): 1,900 mm * Due to the two horizontal positions of the automatically indexing milling head, the vertical machining area can be extended by 576.5 mm. Table area (2 units): Length: 6,000 mm Width: 3,000 mm Number of T-slots on the table surface: 12 Width of T-slots: 22 mm Distance between slots: 250 mm FIBRO Rotary & Sliding Table: Dimensions: 3,000 x 3,000 mm Sliding axis: 1,500 mm Max. table load: 40 t Year of manufacture: 2002 Paint finish: RAL 7021 (black-grey) RAL 7035 (light grey) ref F-38 (DanobatGroup blue) Tool holder: ISO 50, DIN 69871 AD Big Plus Ksdpfxeyu Szno Aqpjdl Pull stud: DIN 69872 Form A Main drive: Drive type: SIEMENS main spindle motor with a 2-stage oil-cooled ZF gearbox Drive power: 100% duty cycle 53 kW (S1) Spindle speed range: Spindle speed: 20–4,000 min-1 Max. torque: at S1 – 100% duty cycle 1,531 Nm Max. feed force: X, Y, Z axis: 31,000 N Max. rapid traverse speed: X, Y, Z axis: 25,000 mm/min BASIC EQUIPMENT OF THE MACHINE: Heidenhain CNC control TNC640 High-performance orthogonal milling head Automatic tool changer (80 positions) Chip conveyor with floor discharge Coolant system with 20 bar & (IKZ) DYNAMICS ACTIVE STABILIZER+ "DAS+ SYSTEM" Cross-axis compensation Automatic milling head change system Operator platform Camera for workspace monitoring Pendulum machining package ACCURA HEADS Optimized Contour Milling (OCM) RepairFIT is our proven solution for a profitable entry into our product lines. Machines available in this line are sourced through a rigorous selection process and undergo a comprehensive inspection (deep-dive check). After thorough cleaning, any obvious defects or faults found are professionally repaired by our expert service team.

Condition: good (used), Year of construction: 2013, Ref. -No.: 10636 Manufacturer: TOS VARNSDORF Type: WHN 13 CNC Year of construction: 2013 Type of control: CNC Control: Heidenhain 530 Storage location: Halberstadt Country of origin: Czech Republic X-Travel: 3500 mm Y-Travel: 2000 mm Z-Travel: 1250 mm W-Axis: 800 mm B-Axis: 360 ° Table Load: 15.000 kg Tool Taper: SK 50 Turning Speeds: 1400 RPM Spindle Speed: 2000 RPM Further information: Kdodpfxoyqmvxj Aqpjl - The control system was converted to a HEIDENHAIN 530i in 2013. - All drives were upgraded to digital. Thrust bearing replacement on the tower also renewed in 2013. - Accessories: - 3D probe - Heidenhain, large spindle support - 1x Heidenhain axis module (completely overhauled), - 1 new axis module is installed in the machine. - Newly packaged spare parts, covers from the machine. - All bearings have been replaced on the machine in recent years. - Tools and milling cutter heads are available. The machine is first-hand. The machine is still powered up and in production. The machine can be viewed by appointment.