VME interface HC010 REV 0.LWL

HOMAG

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Itsdpfxeyqybus Ab Tod Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW Itodsyqx U Hspfx Ab Tod EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, power: 19 kW (25.83 HP), travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,730 mm, number of spindles: 20, number of tool stations in tool turret 1: 18, TECHNICAL DETAILS Working area X-axis: 4,175 mm Working area Y-axis: 1,730 mm Number of suction traverses: 8 Tool magazine positions: 18 Spindles Number of spindles for vertical drilling: 17 Number of spindles for horizontal drilling (X-direction): 2 Number of spindles for horizontal drilling (Y-direction): 1 Total number of spindles: 20 Milling unit Number of controlled axes: 4 Motor power: 18.5 kW Automatic tool changer Liquid-cooled MACHINE DETAILS Total installed power: 19 kW Control model: PC85 EQUIPMENT Iodpfx Abeyttf Ss Tjtd CE marking Front safety cover Note: Cones, milling cutters, and aggregates are not included in the scope of delivery. Safety fences are supplied based on availability (left side only). The machine is sold and delivered in its actual and legal condition (‘as seen and approved’), based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer is entitled to inspect the goods prior to collection, and assumes responsibility for installation, safety, and use of the machine at the destination. External reference: 6906

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,550 mm, workpiece height (max.): 40 mm, number of spindles: 30, travel speed (max.): 80,000 mm/min, TECHNICAL DETAILS Travel range X-axis: 4,175 mm Travel range Y-axis: 1,550 mm Travel speed X-axis: 80 m/min Travel speed Y-axis: 80 m/min Travel speed Z-axis: 30 m/min Maximum workpiece height: 40 mm Number of suction traverse beams: 8 Spindles Number of spindles for vertical drilling: 20 Number of spindles for horizontal drilling in X-direction: 10 Iodpfsyttcwox Ab Totd Total number of spindles: 30 Milling unit Number of controlled axes: 4 + Flex5 Motor power: 15 kW Automatic tool changer Liquid-cooled Saw unit Tool magazine 1 Number of slots: 18 Tool magazine 2 Number of slots: 10 EQUIPMENT NC positioning of suction units Vacuum pump PowerControl P85 control system WoodWop 5.0 machine programming software Note: Cones and milling cutters are not included in the scope of delivery. The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and is responsible for installation, securing, and usage of the machine at the destination. External reference: 7350

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Itodeytr Hbopfx Ab Tod Unit: Top Mill Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: excellent (used), Numerical Control Type Power Control PC85T Software WoodWOP + TOPDRILL No. 2 Through-feed motorized conveyoring belts No. 2 Horizontal units/supports (with Digital quota/axes display) No. 1 Drilling head for each horizontal unit (1 x Kw 1,5) No. 21 Splindles for each horizontal drilling head Itjdpeyv Ev Aefx Ab Tjd Max. working width (mm) 2500 Min. working width (mm) 250 No. 4 Bottom vertical units/supports (with Digital quota/axes display) No. 2 Drilling heads/blocks for each bottom vertical unit (2 x Kw 1,5) No. 4 Vertical top pressure clamps Motorized carpet to evacuate chips and wastes Total installed power (Kw) 35

Condition: used, Year of construction: 2007, total height: 1,200 mm, total length: 3,600 mm, total width: 1,480 mm, - Machine available from: 2025-12-15 - Year: 2007 - Documentation available: Yes - └ Type Documentation: Technical data, Electrical diagrams, User manual, Operating system - └ Language: NL - CE marking present: Yes - CE certificate present: No - Serial number: - Number of units [pcs]: 8 - └ 1st unit type: - - Tools available: Yes - └ 3rd unit type: - - Tools available: Yes - └ 4th unit type: - - Tools available: Yes - └ 5th unit type: - - Tools available: Yes - └ 6th unit type: - - Tools available: Yes - └ 7th unit type: - - Tools available: Yes - Voltage [V]: 400 - Current consumption [A]: 50 - Transport dimensions: 3600mm x 1480mm x 1200mm (l x w x h) - Transport packages [pcs.]: 4 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Iedpfx Abex Ei Sys Totd Yorick Diebels

Condition: used, Year of construction: 2018, total height: 1,650 mm, total length: 4,400 mm, total width: 1,000 mm, Price: On request - Details: - └ Description: Machine currently still has a malfunction to be fixed - Year: 2018 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: - Number of units [pcs]: 9 - └ 1st unit type: - - Tools available: Yes - └ 3rd unit type: - - Tools available: Yes - └ 4th unit type: Isdpfoyvf Nbsx Ab Tetd - - Tools available: Yes - └ 5th unit type: - - Tools available: Yes - └ 6th unit type: - - Tools available: Yes - └ 7th unit type: - - Tools available: Yes - └ 8th unit type: - - Tools available: Yes - └ 9th unit type: - - Tools available: Yes - Voltage [V]: 400 - Current consumption [A]: 10.3 - Fuse [A]: 16 - Transport dimensions: 4400mm x 1000mm x 1650mm (l x w x h) - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), FLEXIBLE C.N.C. WORKING CENTER 3 axes (X-Y-Z) Movable panel (workpiece), static working head - Horizontal position of the panel (workpiece) Safety cabin (enclosure) of the working head Numerical Control PowerControl PC86 power Touch (Software woodWOP) Separate electric and command cabinet No. 2 Workpieces fixing clamps (for the panels introduction in the working area) WEEKE Prepositioning Unit - to position workpieces in machine with clamp grippers faster. In-feeding working table (panel support) and Out-feeding table (with motorized belts) Minimum workpieces dimensions (X - Y - Z) mm 200 x 70 x 8 (2 x 4 mm) Maximum workpiece dimensions (X -Y- Z) mm 3000 x 1000 (option mm 1300) x 80 (2 x 40 mm) Two panels simultaneously processables (in Z axe) Separate electric and command cabinet WORKING GROUPS (TOP): 2V42, 2H8X/2Y, N2 X-Y90,F2-ETP-6 KW No. 1 Vertical electro-spindle ETP-6 (power Kw 6) No. 1 Circular Grooving Saw (90° on X-Y axe) dia. mm 125 No. 42 Vertical drilling spindles (power Kw 2.3) No. 10 Horizontal drilling spindles (8 in X + 2 in Y) Isdpsyu S I Isfx Ab Totd WORKING GROUPS (BOTTOM) 2V42, 2H8X/2Y, N2 X-Y90,F2-ETP-6 KW No. 1 Vertical electro-spindle ETP-6 (power Kw 6) No. 1 Circular Grooving Saw (90° on X-Y axe) dia. mm 125 No. 42 Vertical drilling spindles (power Kw 2.3) No. 10 Horizontal drilling spindles (8 in X + 2 in Y)

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, Specification: Cutting length: 4300mm Cutting Width: 4300mm Saw Blade Projection: 80mm Control Screen on Right Hand Side Isdoyuw Umopfx Ab Totd Machine Table fully air cushioned Program fence Speed forward 25m/min Program fence speed backward 90m/min Standard Clamps: 225, 325, 475, 775, 1075, 1825, 3425mm Power Concept – This allows several strips of different cross cutting lengths to be cut together with a performance increase of up to 40% Pressure beam height control Saw carriage speed 130m/min Main saw motor 11kw with pneumatic lift Scoring saw unit 1.5kw with pneumatic lift Electronic scoring saw adjustment from the control screen 4No air cushion tables 2160 x 650mm Label printer 400V 50Hz Control Touch touch screen monitor Data Transfer via network + USB port CE Eco Plus technologies save up to 20% on energy consumption