Band saw

JAESPA W260 HA

Condition: good (used), Year of construction: 2011, machine/vehicle number: MS 1153, Offer 23158 Technical data ca : - passage to blasting chamber B 370 x 170 mm - blasting nozzle - Door opening to blasting chamber - Blasting material pressure vessel - blasting material recovery - separate control panel - space requirement blast machine 1600 x 2000 x H 1750 mm - space requirement blasting material container 1200 x 1200 x H 2250 mm - Cartridge filter with suction fan MUNK - SCHMITZ - Air volume 700 - 1500 m³/h - Suction fan 3 kW - space requirement filter unit 1600 x 1600 x H 3250 mm - mot. driven inlet roller table 4 m - roller table without drive 3 m Iaedpfxellvr Ds Ab Top - roller width approx. 800 mm - roller table height approx. 700 mm

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW Iodpfxjhzbipe Ab Teap - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: new, Straightening press 150 tons with electric motor and additional manual operation by a hand lever pump, especially for fine work. Versions: 30t 60t 100t 150t 200t ᐳ 200 t: on request Special machines: on request New machine! We are also happy to build a customer-specific press for you. High quality hydraulic workshop press with 150 tons maximum pressing force. The press can also be opened and closed in the classic electric mode using a lever. For fine work (e.g. pressing in bearings, straightening, ...) the press also has a hand pump. This allows you to fine-tune the force manually. The printing cylinder is attached to a sliding carriage so that the cylinder can be moved sideways. In this way, you can make optimal use of the maximum stand passage width. Particularities: - 150 tons maximum pressing force - Pressure display with manometer - 2 operating modes: electrical operation or or manual operation - 2 independent hydraulic pumps - Control cabinet with motor protection monitoring and safety devices - adjustable passage height - Pull chains for easy adjustment of the passage height - massive machine frame - cylinder laterally adjustable (mounted on sliding carriage) The press can be tested under power on site. ----- Numerous other workshop presses in different designs, sizes and with optional additional equipment available! 30, 60, 100, 150, 180, 200 tons. Iaedpfx Ajf Sqcksb Tep ----- Please just contact us, we will be happy to advise you without obligation. The stated price is net plus 19% VAT. All statements without guarantee! Europe-wide delivery possible! ----- The European Commission provides a platform for out-of-court online dispute resolution (OS platform). The offer serves exclusively as an internet presentation of our goods. The contract negotiation comes about by means of telecommunication (email, fax, telephone, news portal), where we first make you a non-binding offer, in which we inform you about our general terms and conditions and the right of withdrawal with imprint before the purchase / contract is concluded.

Condition: used, TECHNICAL DETAILS TABLE - Table dimensions : 3100/800 [mm] - Maximum weight upon table : 7000 [kg] - Travels on X/Y/Z axes : 3000/1000/1200 [mm] - Rapid traverses rates (X/Y/Z) : 15000/15000/15000 [mm/min] MILLING HEAD Manual head MILLING SPINDLE - Tool holder type : ISO50 * Spindle speeds : 4000 [rpm] * Spindle power : 27 [kW] TOOL CHANGER - Auto. Tool Changer type : Parapluie - Tool magazine capacity : 24 WEIGHT & DIMENSIONS - Machine floor space : 7913/5043 [mm] - Machine height : 3440 [mm] - Machine weight : 13410 [kg] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 38 [kW] MACHINE HOURS - Number of hours under power : 24689 [h] - Number of working hours : 23809 [h] - Number of spindle hours : 7658 [h] EQUIPMENT Iedpfxsw Tnhbs Ab Toap - CNC : Heidenhain iTNC530 - Electronic handwheel Interface : RS232/RJ45/USB - Interactive programming - Coolant tank - Tool-holders

Condition: like new (used), Year of construction: 2021, operating hours: 1,200 h, functionality: fully functional, turning diameter: 1,100 mm, power: 46 kW (62.54 HP), distance between centers: 2,000 mm, load hours: 1,200 h, A DMT CD1100 lathe with Heidenhain control and only 1,200 operating hours is available. The working area offers a swing diameter of approx. 1,100 mm over the bed and approx. 800 mm over the cross-slide. The tool holder is a Multifix D1. The distance between centers is 2,000 mm. The main spindle drive is a motor with 46 kW output at 60% duty cycle and two gearbox stages. Tailstock: - Quill diameter: 125 mm - Taper: 6 Morse taper Delivery: Collection by the buyer Payment: 100% via bank transfer immediately upon invoicing, prior to collection All information is non-binding. Subject to prior sale. The machine is sold without any guarantee or warranty claims and remains our property until full payment is received. Iaedoxlza Hspfx Ab Top

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 510-1986, CYLINDRICAL GRINDER JOTES SCHAUDT A440X1500 Specifications Maximum longitudinal travel: 1500 mm Grinding diameter: 298 mm External grinding: Yes Internal grinding: Yes Dimensions (L x W x H): 5400 × 2400 × 1600 mm Weight: 4800 kg Operating hours: — Power-on hours: — Condition: Rebuilt Compliant with local standards: — Status: Under power Technical features - Grinding length [mm]: 1500 - Grinding diameter [mm]: 300 - Manual table displacement [mm/rev]: 10 - Table speed range [mm/s]: 0.01–5 - Smallest table stroke [mm]: 3 - Wheelhead swivel [°]: ±90 - Centre sleeve taper [Morse No.]: 4 Iedpfx Abew T Ti Dj Toap - Grinding wheel dimensions [mm]: 500 x 63 x 203 - Spindle speed [rpm]: 32–500 - Grinding wheel drive motor power [kW]: 5.5 - Workpiece drive motor power [kW]: 0.75 - Hydraulic pump motor power [kW]: 1.5 - Grinding attachment drive motor power [kW]: 0.75 - Machine dimensions [mm]: L=5400 / W=2400 / H=1580 / Machine weight [kg]: 4800

Condition: new, Bernardo universal lathe Titan 660 x 2000 Technical Specifications Centre distance 2000 mm Centre height 330 mm Swing diameter over bed 660 mm Swing diameter over cranking 900 mm Swing diameter over cross slide 460 mm Bed width 400 mm Spindle bore 105 mm Spindle mounting DIN 55029, D1-8 Speed range (16) 25 - 1600 rpm Range of longitudinal feeds (25) 0.044 - 1.48 mm/U Plan feed range (25) 0.022 - 0.740 mm/U Metric threads (54) 0.45 - 120 mm inch thread (54) 7/16 - 80 Gg/1″ Pinol diameter 90 mm Sleeve travel 235 mm Iasdpfx Absfbbx Re Top Sleeve holder MK 5 Engine power 7,5 kW (10,0 PS) Machine dimensions (W x D x H) 3630 x 1200 x 1520 mm Weight approx. 2900 kg Features & Benefits Versatile application possibilities in general mechanical engineering, production, single part production, ... Central, handy switch for feeds and threads with guide and feed spindle Prism bed made of grey cast iron, inductively hardened and precision ground Modern main spindle bearings with angular contact roller bearings in precision design Hardened and ground gears and shafts, also in the feed gear Rapid traverse lengthwise and flat as standard to reduce non-productive times Large spindle bore (105 mm) for large diameter workpieces Soft start due to the mechanical multi-disc clutch Electromechanical foot brake to reduce non-productive time Best cutting performance even during face turning For stiffening the bed guide and for minimizing

Condition: as good as new (ex-display), Year of construction: 2024, General Tool magazine : 2x chain magazine with 32 stations each Rapid traverse in X/Y/Z : 48 m/min Traverse path X/Y/Z : 800/900/620 mm Spindle Technology : Direct drive Speed : 15.000 rpm Tool holder : HSK-A63 NC rotary table Technology : Swivel rotary table with torque drive, made by Kessler A-axis : +/- 120 C-axis : 360° Clamping surface : ø800 mm Table load (max.) : 1,000 kg Isdpfx Aeur Ng Uob Toap Workpiece dimensions (max.) : ø800 x 500 mm Equipment Distance measuring system : Direct (glass scales) in all axes Chip management : Chip conveyor Coolant management : IKZ system with filter and high pressure, 18 bar Workpiece measurement : Touch probe, Heidenhain TS 740 Tool measurement : Laser, BLUM Set-up mode : Electronic handwheel Additional equipment : Spindle cooler

Year of construction: 2024, condition: new, New mechanical and electromagnetic clutches and brakes for Bulgarian machine tools of the following types: CU400, CU500, CU502, CU580M, CU582, C11MT, C11MB, C11, C13B… We also offer a wide selection of various spare parts for the above-mentioned machine tools, most of which are available from stock, while for the rest we offer the fastest possible delivery times. We cordially invite you to cooperate! Iaedpfjv Rpn Tox Ab Tsp

Condition: good (used), Spindle diameter: 80 mm Spindle nose: SK50 Spindle speeds: 11 - 1000 RPM X-axis movement: 1700 mm Y-axis movement: 1800 mm Z-axis movement: 1800 mm Spindle out (W-axis): 710 mm Table size: 1100 x 900 mm Elbo Digital readout: On Y-axis and Z-axis Featured with: - Turning table - Toolholders Spindle engine: 7,5 KW Machine LxWxH: 5100 x 2650 x 3300 mm Machine weight: 10 Ton Iedpfxephl Ece Ab Tjap