Gaiser 4000 steam cleaner

Gaiser 4000

Condition: used, Marvel Townsend StorkDMM50 meat bone separator to produce best quality low pressure deboned meat when used in conjunction with a Baader or SEPAmatic. This machine has come direct from a closed meat factory in Scotland. Almost impossible to find these machines on the used market. Iodpfx Ajlkc I Rogzjbf

Year of construction: 2001, condition: used, Max. pressure: 500t, max. operational temperature: 370°C, oil heated, oil cooled, with a secondary cycle for recirculation of heating output, was overhauled in 2014. Iedpfx Agsdwf Dbezebf

Condition: used, CNC Gantry-Type Boring and Milling Machine ANAYAK Type HVM-3800-P Iodpfxjxcgtgo Agzobf Bed type milling machine, structure similar to a plate-type boring mill with fixed table Machine No.: M-20021203 Year of manufacture: 2002 ("Refurbished 2025") The machine will be completely workshop overhauled in 2025 and can then be inspected in storage at 37235 Hessisch Lichtenau. Travel distances: X: 3,200 mm, Y: 1,200 mm, Z: 1,500 mm Table size: 3,800 x 1,200 mm T-slots: 8 pieces, 22 mm, spacing 130 mm Table load: max. 25 tons (stationary table – virtually unlimited load capacity) Spindle taper: ISO 50 (DIN69871-A) (drawbar: DIN 69872-B) Spindle speed: 60 – 4,000 rpm, stepless Feed rate: up to 10,000 mm/min, stepless Rapid traverse X + Y: 20 m/min Rapid traverse Z: 10 m/min Spindle drive: 22 / 30 kW Electrical connection: 400 Volt, 50 Hz, 50 kVA - Automatic tool changer for 30 tools - Spindle drive with 2 speed ranges - With automatic tool changer and tool magazine - Orthogonal milling head with hydro-mechanical tool clamping - Orthogonal milling head fully automatic swiveling in two 45° planes – B+C axis - HEIDENHAIN iTNC 530 control, with electronic handwheel - Prepared for wireless touch probe (probe and receiver not included) - Additional HF-spindle, 18,000 rpm – for attachment - Free-standing control cabinet - Chip conveyor positioned between the gantry bed and the machine table - 32,078 operating hours recorded - Coolant system - Free-standing hydraulic unit - Operating manual with circuit diagrams Installation area (L x W): approx. 1,000 x 700 cm Installation height: approx. 410 cm Weight (total): approx. 33 tons Good condition

Year of construction: 2023, condition: new, - modern ergonomic design - manual test with analogue Measuring Clock (Reading accuracy 0.2 HR) - easy to use and quick test process - Height Capacity approx. 185mm - Hepth Capacity approx. 160mm - Dimensions 545x182x755mm Test loads: 60 / 100 / 150kg Test method: HRA/HRB/HRC Standard delivery: - Hardness tester - V-Anvil - Flat Anvil Ø150mm - Flat Anvil Ø50mm - Ball Indenter 1/16" with ball - Diamond indenter 120° Rockwell - Spindle protection Ibedpspbbc Hefx Agzjf - Accessory case

Condition: as good as new (ex-display), Year of construction: 2015, operating hours: 985 h, travel distance X-axis: 905 mm, travel distance Y-axis: 705 mm, travel distance Z-axis: 455 mm, workpiece weight (max.): 3,000 kg, EDM314MF30 - SLM (second-live-machine) General overhaul Travel paths X x Y x Z 900x705x455mm Machine table 1150x850mm Container size 1200x900mm Distance table/chuck 260/710mm Electrode weight 50/500kg Workpiece weight max. 3000kg Overall dimensions of machine 2210x3450x3250mm Power supply 400V/DS/50/60Hz Container height 750mm Equipment: MF30 user interface Movable control panel Touch screen Lift speed 15000mm/min (high jump) Eroding generator 60A Integrated cooling unit Cartridge filter system Tool changer 8-fold C-axis with direct measurement, resolution 0.0001 degrees C-axis as positioning - rotation - and erosion axis C-axis 100 rpm. Iodpjhfaizsfx Agzebf Automatic container tracking Filling, filter and rinsing pump Transport IB Training 12 month warranty

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end Iedpfx Aefzb Niegzobf The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Condition: new, No. 3187 Vacuum dryer / drying chamber ISVE ES 5 / NEW New machine, delivery time 120 days Construction features: AISI-304 stainless steel, partially insulated External diameter: 1600 mm Length of cylindrical part: 5000 mm Dryer length: 5900 mm Dryer total length plus sliding guides: 11000 mm Max. operating vacuum: -730 mm Hg Timber pile length: 5000 mm Timber pile width: 1100 mm Timber pile height: 990 mm Net wood volume: approx. 5 m3 Installed electrical power: 16,01 kW Average hourly power input: 8 kW/h Includes: - 12 electric heating plates (each 1100 x 5000 x 10 mm LWH / 57 kg / 1,25 kW) - 2 internal condensers (turbofan of 0,55 kW each 380 VCa with stainless steel pipes) - 1 one-way valve (clapet: one ¾” for vacuum circuit) - 1 solenoid air return valve (24 Vca: one 1” for the autoclave) - 1 manual air return (1” ball valve) - 1 electrical control panel (PLC type Siemens S7-1200, with touch panel) - 1 ISVE server connect with remote service and control - 2 wireless moisture probes (double probes for core and surface moisture reading) - 1 wireless temperature probe (for wood core reading) - 2 plates-holder stands - 1 instruction booklet (in English with CE certificate and wiring diagrams) Transport dimensions approx. 5900 x 1620 x 2300 mm LWH Weight approx. 2900 kg Technical details, year of construction and scope of delivery according to the manufacturer, without guarantee Ibjdpfx Aevc Axpegzof Subject to prior sale New machines are covered by the manufacturer's warranty Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, Controller FANUC Series 18i-MB Table size 1300 x 650 mm Table load 1500 kgs X travel 1100 mm Y travel 650 mm Z travel 600 mm Spindle speed 12000 rpm Ibjdpfxjuu Rzre Agzjf Tool holder type MAS BT40 ATC magazin 30-fold Weight 7200 kgs Dimensions LxWxH = 3100 x 2300 x 3100 mm Features, accessories - Chip conveyor - Coolant unit - Spindle cooler - CTS - Manuals Very good condition.It will be sold because of liquidation of production.

Year of construction: 2017, condition: ready for operation (used), - USED - TRAVELLING COLUMN CNC MILLING MACHINE WITH AUTOMATIC A/B-AXIS HEAD LONGITUDINAL TRAVEL: 3500 mm TRANSVERSAL TRAVEL: 1100 mm VERTICAL TRAVEL: 1500 mm RAPID FEEDS L-T-V: 40 m/min TABLE SIZE: 3800 x 1000 mm HEAD: A/B AXIS AUTOMATIC ; MILLESIMAL POSITIONING ; ISO 50 ; 5000 rpm; 34 kW TOOL MAGAZINE: CHAIN-TYPE ; 40 POS CONTROL UNIT: HEIDENHAIN TNC 640 Iedpfxswla Hzo Agzebf HIGH PRESSURE COOLANT: 40 Bar WEIGHT: 35020 Kg OVERALL DIMENSIONS: 8760 x 4950 x 3780 mm ACCESSORIES: SWARF CONVEYOR ; LASER TOOL SETTER ; TOUCH PROBE ; PORTABLE HANDWHEEL

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: 538518/1, Dear interested party, You will find all the data on the plant in the photos and in the PDF files. The plant can be viewed by appointment. We will be happy to answer any further questions you may have. Isdpfsumv Alex Agzjbf