Used Albert Goecker Kg for sale (67,954)

Condition: excellent (used), Heavy duty wooden pallets with 3 skids accessible from 4 sides length 1680 mm width 1250 mm board thickness 45 mm weight 82,5 kg several available Kjdpfsl Uvv Tox Ahyedg

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Kjdpox A U Ncsfx Ahyjdg Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: reconditioned (used), Year of construction: 2014, operating hours: 5,612 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total height: 2,800 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), volume flow: 332 m³/h, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,612 hours, stand August 2025 Press power main press 48 tons Specific press capacity 58,2 N/cm² Kdjdpfx Ahevtpq Hoyog Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press was partially overhauled and tested in our workshop, see photos and our function video. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: like new (used), functionality: not functional, load capacity: 6,500 kg, Load capacity 6500 kg Please note: Arm diameter adjustable from 1880 mm to 4550 mm (swivel-out) Space-saving and continuously adjustable, the extension arms can be locked in place Speed continuously adjustable from 0.001 to 5 rpm Motor power 3 kW Torque 15000 Nm Height 800 mm Maximum current transmission 2000 A Weight 4700 kg with hand and double-foot remote control CE certificate, declaration of conformity, documentation, circuit diagram Ksdpjx Thucjfx Ahyedg with original 2016 quotation invoice Current new price approx. €28,000

Condition: new, 21.25 m² storage platform incl. stairs, railings on two sides, top edge 300 cm, 500 kg/m², immediately ex warehouse, accessible with pallet truck, system platform, steel platform, storage level Data : - Length: 5000 mm - Width: 4250 mm - Size can be extended on request - Clear height below the platform: 2612 mm - Support grid: 4605 x 3850 mm - Plus 200 mm overhang of the floor covering - Supports, stairs, railing posts, cross bracing & dome struts powder-coated in RAL 7016 - Handrail, knee rail, roll-off edge, main & secondary beams galvanized - Floor covering: 38 mm chipboard P6, OK natural & UK white - New from stock Wietmarschen - AVAILABLE IMMEDIATELY Storage platform consists of : - 04 x upright - 02 x main beam C+350 - 06 x secondary beam S+260 - 01 x intersection - 02 x strut brace - 10 x Chipboard - 01 x Stairs, 37° incline - Approx. 8.25 running meters Railing - Incl. connecting material & screws -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 5026,00 € net 5980,94 € gross You will receive an invoice with VAT shown. Kedpfsybaxhsx Ahyedg Transportation : The delivery is carried out on request by our partner forwarding agency, the costs for this depend on the postal code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation. Are you interested or do you have any questions? Simply contact us by message or phone call. You can find our telephone number on our company page. ☎️ You can reach us by phone from Monday to Friday, 08:00 - 15:00. Alternatively, you can send us a message with your name and number and we will get back to you as soon as possible.

Condition: good (used), Year of construction: 1970, Transformer, transformer, converter, three-phase autotransformer, isolating transformer, 3-phase transformer Kedpfx Asb Iqgnohyodg -PCB containing insulating liquid exchanged in 1998 -Input: 6000V -Output: 400V -Power: 200kVA -Type: LT -(for technical data see photos) -Dimensions: approx. 1300/800/H1600 mm -Weight: about 1000 kg

Condition: good (used), Year of construction: 1973, machine/vehicle number: 73040, Embossing press Baier GEBA 1/F, installation height 90 mm, pressure capacity 800 kg, working size 10cm x 14 cm, built in 1973, machine number 73040, in good condition, immediately available Kdodpfx Ahsvt Rpqeyog If you are interested, we would be happy to inform you about other machines in our company. You are welcome to view the machine in our company by prior appointment.

Condition: used, Year of construction: 1984, load capacity: 3,200 kg, Currently 4 units in stock. Single girder semi-gantry crane Manufacturer: Christmann & Pfeifer KG Hoist: Demag Model: PLV 168 NF Kdedpfew Ugu Asx Ahysg Load capacity: 3,200 kg Travel mechanism: Demag Type: 13/6PF 12/4 Usable hook path: 4,800 mm Track gauge (center-to-center): 8,110 mm Weight: approx. 2 t/unit Price per unit, loaded free of charge. The cranes have already been dismantled and are packaged for transport. Machine can be inspected onsite. All information subject to change. Prior sale reserved.

Condition: used, Year of construction: 1989, Technical details: length: 12 200 mm width: 2 500 mm height: 2 600 mm weight of the machine ca.: Eigengewicht ca. 4,5 t 2 pieces containers, 40 feet, heated Extinguishing system container - insulated container (food refrigerated container) Extinguishing system container with 20.000Liter water tank/tank Mixing station, with corresponding electronics and piping as well as pump station (without pumps) Kdsdpfx Aheu N Anhjyjg i.D. *

Year of construction: 2003, condition: good (used), functionality: fully functional, machine/vehicle number: 03234, 6 Brush ( 3 pairs) descaling machine for steel wire size 5.5mm - 16.0 mm max (low carbon) Brush pairs arranged in a 60 degree offset for maximum effect. A very clean looking machine. Kdedpfx Aex R Uzdohyog On site viewing and inspection recommended

Condition: new, Year of construction: 2025, Hand pallet truck 2000 kg LWPW with weighing system, new 2025. Continuous stock, see our website. Prices are ex Nuland. Van de Wert Trading B.V. has a variable stock of machines, trucks, trailers, and attachments. All deliveries are offered at trade prices in AS-IS condition without warranty. (see our general terms and conditions) For a viewing and/or test drive, you can schedule a non-binding appointment. Please call in advance, as we are not always present. Kdjdox Td Dtopfx Ahyjg Van de Wert Trading B.V. Bedrijfsstraat 3 5391 LR Nuland

Condition: new, functionality: fully functional, Year of construction: 2022, ATEX rotational valve, 1,5kw- 18rpm. Special heavy duty. Kodpfx Ahjx Dzc Esyodg SEW drive with cooler fan. Special knive system. Special 5 line sleeve system. Inert gas adding hole. Possible to buy 2 new, and 5 slightly used valves.

Year of construction: 1969, condition: used, Swivel bending machine Albert steel TYpABK 400 /5 Kdodpfxeh Rkh Do Ahysg useful length 2530 mm Sheet thickness 5 mm

Condition: new, The scope of delivery includes: 01x wire grating, new Material color: sendzimir galvanized Execution: laid-on shelf grating, folded on both sides total depth: 1.112 mm clear span: 1.000 mm total width: 890 mm mesh size: 106 x 72.5 mm wire thickness: 3,8 mm Number of beams: 4 pcs. Unit weight: approx. 5.14 kg Kodpfsilk Ngjx Ahysdg Technical data: Tested load capacity: 500 kg according to ANSI MH 26.2 for beam depth: 1.100 mm Assumed beam width: 50 mm Application for indoor use only Possibility of use: Shelf size/ modules required per shelf 1,100 x 1,800 mm/ 2 pcs. 1,100 x 2,700 mm/ 3 pcs. 1,100 x 3,600 mm/ 4 pcs. Heat resistant sheets: On request, we can offer you heat resistant sheets (see picture material) for sale; prices on request. Fire protection has special requirements. Therefore, the wire meshes can be provided with a welded-on heat shield. And should you need a push-through protection for cardboard boxes, the heat shield can also be made with a bend. General information about the article: This item is offered for pickup only. Any additional transport or shipment of this article is subject to additional costs, which will be charged separately to the customer. depending on the delivery location or scope of delivery can be requested from us.

Condition: new, The scope of delivery includes: 01x wire grating, new Material color: sendzimir galvanized Execution: laid-on shelf grating, folded on both sides total depth: 1.112 mm clear span: 1.000 mm total width: 890 mm mesh size: 106 x 53 mm wire thickness: 3,8 mm Number of beams: 7 pcs. Unit weight: approx. 7.53 kg Technical data: Tested load capacity: 1,000 kg according to ANSI MH 26.2 for beam depth: 1,100 mm Assumed crosshead width: 50 mm Application for indoor use only Kdsdpeilk Nrsfx Ahyjg Possibility of use: Shelf size/ modules required per shelf 1,100 x 1,800 mm/ 2 pcs. 1,100 x 2,700 mm/ 3 pcs. 1,100 x 3,600 mm/ 4 pcs. Heat resistant sheets: On request, we can offer you heat resistant sheets (see picture material) for sale; prices on request. Fire protection has special requirements. Therefore, the wire meshes can be provided with a welded-on heat shield. And should you need a push-through protection for cardboard boxes, the heat shield can also be made with a bend. General information about the article: This item is offered for pickup only. Any further transport or shipment of this or a shipment of this item is associated with additional costs, which are separately depending on the delivery location or scope of delivery can be requested from us.

Condition: new, Year of construction: 2025, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 600-700 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site Kdedpfxsndn Ago Ahyjg - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2026, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Kdedpfx Ahong Exajyeg Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 800-900 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: good (used), Year of construction: 2005, operating hours: 527 h, functionality: fully functional, machine/vehicle number: 05-9473, travel distance X-axis: 2,500 mm, travel distance Y-axis: 1,100 mm, travel distance Z-axis: 60 mm, total height: 2,000 mm, total length: 1,600 mm, total width: 3,800 mm, rotational speed (max.): 12,000 rpm, input voltage: 400 V, The machine in question is a grinding and drilling center (manufacturer designation: stone cutting machine). The machine is designed as a vertical machining center in a gantry design. The frame consists of a welded steel tube construction. The drilling head is mounted vertically. There is no angular adjustment possible on any axis for the drilling head. Tools with horizontal shafts can be attached via an existing angle grinder attachment. The tool can be moved linearly along 3 axes: x, y (horizontal), and z (vertical). The machine table is fixed and does not move. The machine is used for: - Creating cutouts and round edge profiles - Making drip edges or drip grooves, polishing surfaces, polishing edges, and drilling natural stone slabs The machine is also equipped with: - an angle grinder attachment - a compressed air connection (for generating vacuum for clamping fixtures and for cleaning the drill spindle) - a water connection (for cooling tools and workpieces during machining) Machine Data: Manufacturer: Martin Kolb Maschinenbau - Model: Genius 2500 - Serial Number: 05-9473 - Year of Manufacture: 2005 - Max. working area: 2,500 x 1,100 mm - Max. workpiece thickness: 60 mm - Main drive power: 6 kW (400V / 50 Hz) - Spindle speed: 0 - 12,000 rpm (frequency controlled) Ksdpew Upzfefx Ahyjdg - Tool holder: 1/2 inch thread - Max. drilling diameter: up to 100 mm Various accessories such as milling cutters and other tool holders are also included.

Condition: excellent (used), Professional workshop crane with counterweight and hydraulic drive. Very good condition, fully operational, ready for use. • Model: Hydrobull HB 500 GK • Manufacturer: E. Ziegler GmbH, Renningen (Germany) • Year of manufacture: 2004 • Lifting capacity: 500 kg • Lifting height: 280 cm • Jib length: 150 cm • Counterweight: 850 kg • Own weight: approx. 1200 kg (350 + 850 kg GG) • Outreach range: A1–A7 (240–500 kg, according to load chart) • Steel construction, mobile on industrial wheels • Hydraulic lifting and lowering of the jib • Technical and visual condition: very good Kdsdpfexmt H Isx Ahyog

Year of construction: 2026, condition: as good as new (ex-display), The BTS-Tyre Packing Machine Gen.2 is ideal for used tyre companies with large tyre volumes. The triple machine is the perfect solution for cost-effective disposal or resale of second-hand tyres. By doubling or tripling the tyres you achieve an enormous volume reduction, the available storage and loading capacity, as well as the permissible transport weight can be used much more efficiently. Pressing cylinder: Pneumatic Pressing force: 1.23 kN, adjustable Machine size: 1250 H x 1930 W x 660 D mm Machine weight: 93 kg Transport size: 1250 H x 1200 W x 800 D mm Working height: 800 - 1020 mm, adjustable Kedpfx Aob Rz R Ujhyjdg Power supply: Air, up to 10 bar / 145 Psi Working pressure: 6 - 8 bar User-friendly and safe two hand control Strong and long-life design High-performance pneumatic cylinder Ball bearing roller guides Adjustable working height Low noise level by silencer Air quick connector A quality product “Made in Germany” Suitable for doubling and tripling Second-hand tyres Optional extras Machine colour RAL BTS-MF550HD Scrap Tyre Baler Demo-Video shows BTS-Tyre Packing Machine Gen.1, the BTS-Tyre Packing Machine Gen.2 operates on same way. Tyre packing machine, Tyre triple machine, Tyre double machine, Tyre doubler, Tyre tripler, Tyre packer, Tire packing pachine, Tire tripling machine, Tyre doubling machine, Tire doubling machine

Condition: good (used), Year of construction: 2024, Welding turntable KT 300 Load horizontal 300 KG, tilted 150 KG Power consumption 220V, 50 Hz table diameter 450mm Kdedpfx Ajbvk I Eohyog height 500mm Tilt range stepless via crank gear motor 0 - 90°. speed 0,3 - 2,5 rpm Incl. foot remote control Surcharge: Quick release - jaw chuck diameter 300mm, 450.-€

Condition: new, Year of construction: 2024, load capacity: 300 kg, Equipment: foot remote control, rotational speed infinitely variable, Protec KT 300 H welding turntable, 170/400 special version Horizontal load 300 kg, tilted 150 kg Power consumption 220 V, 50 Hz Table diameter 450mm Hollow shaft diameter 170mm Table height 500mm Welding current transmission 400 A Quick-action chuck diameter 300mm, surcharge 550.-€ Quick-action chuck diameter 400mm, surcharge 750.-€ Kdedpfx Aevbrqxjhyjg Crank gear motor 0 - 90° stepless adjustment Infinitely variable speed 0.01 to approx. 5 rpm. incl. foot remote control Digital display with welding time limiter (if required)

Condition: like new (used), functionality: fully functional, load capacity: 6,500 kg, Load capacity 6500 kg Please note: Arm diameter adjustable from 1880 mm to 4550 mm (swivel-out) Space-saving and continuously adjustable, the extension arms can be locked in place Speed continuously adjustable from 0.001 to 5 rpm Motor power 3 kW Torque 15000 Nm Height 800 mm Maximum current transmission 2000 A Kdjdjwd Twqjpfx Ahyog Weight 4700 kg with hand and double-foot remote control CE certificate, declaration of conformity, documentation, circuit diagram with original 2016 quotation invoice Current new price approx. €28,000

Condition: new, Year of construction: 2025, functionality: fully functional, load capacity: 1,000 kg, table load: 1,000 kg, 3-axis turning and tilting positioner with 1000 kg load capacity, clamping plate diameter 0.65 meters Height adjustment 1000 - 1500 mm Suitable for welding, assembly, processing, etc. With its stable and robust construction, flexible positioning via three axes including overhead, and user-friendly operation, it facilitates welding, assembly, and handling of large workpieces. Ksdpsxbh Dqofx Ahyodg Optimal positioning of the workpiece improves welding quality and allows higher specified loads in any position. Thanks to the endless rotation of the two rotary axes and additional height adjustment, all workpiece positions (including overhead) are possible. Turntable speed infinitely adjustable from 0.1 to 1.0 rpm. With wireless remote control Rotation range 360° infinite Swivel range 360° infinite Lift: 1000 - 1500 mm Arm outreach radius: 1 meter

Condition: used, Year of construction: 2006, functionality: fully functional, machine/vehicle number: 13-3188, total length: 160,000 mm, total height: 3,000 mm, total width: 9,000 mm, temperature: 230 °C, volume flow: 100 m³/h, Powder Coating System ARNO HERING PTR 15-45-SE (Year 2006) For sale is a complete powder coating system from ARNO HERING (model PTR 15-45-SE), manufactured in 05/2006. The system consists of an application booth, drying/curing oven, and crane rail/carrier racks (hanging racks). The system is from ongoing production and is suitable for coating metal parts and assemblies. Highlights / Equipment (Components): - Application booth (powder application) - Drying oven / curing oven - Crane rail / manual overhead conveyor system including carrier/hanging racks - Documentation/control manuals: to be included if available Technical Data (according to nameplate): - Model: PTR 15-45-SE - Year of manufacture: 05/2006 - Machine number: 13-3188 - Max. drying temperature: 230 °C - Minimum exhaust air volume (at 20 °C): 100 m³/h - Max. permitted powder quantity: 10 kg/h Notes: - Inspection on site is possible by appointment. - Loading/dismantling: by arrangement (possibly to be handled by the buyer). - Sale ex location, subject to prior sale. We are offering this used ARNO HERING PTR 15-45-SE powder coating system, year 2006. Model: PTR 15-45-SE Year: May 2006 Kdedpfx Ahsx Squ Aeyog Machine number: 13-3188 Maximum drying temperature: 230 °C Minimum exhaust air volume at 20°C: 100 m³/h Maximum permitted powder quantity: 10 kg/h If you have any questions or need further information, please feel free to send us a message or call us.