Used Cold Store for sale (3,234)

Condition: ready for operation (used), Year of construction: 1974, disk of circular saw-Ø: 400 mm Cjdpfxstp Hgte Afnopu cutting area at 90° round: 120 mm cutting area at 90° square: 200 x 80 mm cutting area in mitre at 45° square: 150 x 70 mm cutting speed: 13, 17, 26 m/min engine: 380 V, 1,7/2,2/2,6 kW space needed: 1050 x 1000 x 1680 mm weight: ca. 850 kg

Condition: good (used), Year of construction: 1968, Saw blade diameter 370 mm Cutting capacity 45° - 90 round 115 mm flat approx. 215 x 20 mm rectangular approx. 95 x 105 mm U-profile approx. 160 x 55 mm Cutting speed 30, 60, 130 and 260 m/min Motor power approx. 2.6 kW Dimensions L x W x H 1100 x 1050 x 1600 mm Weight 850 kg Accessories / Special features: - Semi-automatic operation - After starting, the workpiece is automatically clamped with the upper clamping cylinder. Once the set feed end has been reached, the saw blade moves down automatically and the clamping vice is released again. - Hydro-pneumatic stepless saw blade feed - Mitre cut on both sides R - L - 0° longitudinal cut possible - Coolant system - 1 saw blade Cpodpsrwyfqefx Afneu Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: used, Year of construction: 1972, 1 used, well-preserved hydro-pneumatic semi-automatic cold circular sawing machine for cutting aluminum, non-ferrous metals, wood and plastic Technical data: max. saw blade diameter 370 mm Cutting diameter 120 mm Cutting range at 90 degrees: flat 260 x 60 mm Cutting range at 90 degrees: square 105 mm Cutting range at 45 degrees: flat 200 x 45 mm Cutting range at 45 degrees: square 90 mm 0° cut - longitudinal cut: yes Cpodpfx Aebwl Emsfnju 2 speeds 1500 / 3000 m/min Drive cable 1.7 / 2.6 kW Machine dimensions L x W x H 1000 x 1000 x 1700 mm Machine weight 700 kg Accessories / Special features: - Semi-automatic operation: After starting, the workpiece is automatically clamped with the upper clamping cylinder. Once the set feed end has been reached, the saw blade moves down automatically and the clamping vice is released. - Stepless feed - Pole-changing motor - 1 saw blade - Mitre cut on both sides - Longitudinal cut 0° - Spray lever device Special accessories: - 1 roller table right with heavy stop 3500 mm and scale - 1 roller table left, approx. 3500 mm Special accessory price: € 1,500.00 plus VAT. Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: ready for operation (used), Technical characteristics Pressing dimensions Useful length: 6000 mm Cpedet N Aumopfx Afnsu Useful width: 1300 mm Passage height 1000 mm with extension 500 mm Cylinder stroke mm Height floor / worktop 300 mm 1400 mm working height 12 independent trays Power and Motors Overall dimensions Lenght: 6750 mm Width: 2000 mm Height: 2600 mm Weight: 8000 Kg

Condition: excellent (used), Offered here is a water cooler generator from the company Lennox. LENNOX chiller 400 V without condenser for indoor installation two cooling circuits capacity: 153 kW R 407 C low mileage dimensions H x X W x D: 1750 x 1500 x 650 mm For technical data please refer to the nameplate.

You will receive a proper invoice with VAT. The price is incl. VAT.
We have more various interesting things for sale. Please have a look at all our ads.
If you are interested or have any questions, please contact us via the message function! Cjdpfx Aog Uv Ayefnjpu

Condition: used, saw blade diameter 350 mm cutting diameter 90 mm stroke 160 mm mitter cutting - all-position ± 45 ° voltage 380 V weight of the machine ca. 350 kg dimensions of the machine ca. 0,80 x 0,85 x 1,35 m - S/N: 4296 - pneumatic feed - coolant equipment Cpsdped Il Azofx Afnsu

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 109 956, workpiece diameter (max.): 38 mm, workpiece length (max.): 500 mm, TECHNICAL DETAILS Workpiece Rack Length: max. 610 mm Workpiece Diameter: 38 mm Module Range: 0.3 – 1.3 Max. Slide Stroke: 1130 mm Max. Rolling Bar Length: 915 mm Max. Profile Outer Diameter (Standard): 50 mm Max. Profile Width (Standard): 125 mm Gear Cutting (Rollability): 0.3–1.25 Machine Cycle Times Tailstock forward (approx. 300 mm stroke): 1.0 s Rolling bars forward: 4.2 s Tailstock return (approx. 300 mm stroke): 1.5 s Rolling bars return: 4.8 s Loading/Unloading (manual): 5 s MACHINE DETAILS Cpjdpfx Afjwx H R Tenou Weight & Dimensions Total Weight (without automation): 12,200 kg Overall Width: 5,014 mm Machine Width: 3,104 mm Depth without cantilever: 2,564 mm Depth with cantilever: 4,166 mm Hydraulic System Hydraulic Tank: 1,000 l Hydraulic Operating Pressure: 80 bar Electrical Equipment Operating Voltage: 400 V / 3 phases Frequency: 50 ±1 Hz Coolant System Tank Capacity: 260 l Pump Pressure: 3 bar Pump Flow Rate: 24 l/min Cooling Water Supply for Hydraulic Tank (Quantity): 10 l/min Cooling Water Connection for Hydraulic Tank (Temperature): 20 °C EQUIPMENT Full enclosure included Tailstock included Hydraulic system included Oil system included

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: 109987 - 2800015, workpiece diameter (max.): 38 mm, workpiece length (max.): 500 mm, stroke length: 1,950 mm, Suitable for chipless cold forming of profiles such as splines (straight or helical), spiral gears, oil grooves, CV joints, threads and knurls TECHNICAL DETAILS Workpiece diameter: 38 mm Workpiece length: 500 mm Rack length – max.: 610 mm Max. slide stroke: 1,950 mm Max. rolling bar length: 1,400 + 330 mm Max. profile external diameter (standard): 60 mm Max. profile width (standard): 175 mm Rollable profiles for involute gears (module range): 0.3–2.0 MACHINE DETAILS Machine weight: 10 t Cjdpfx Aewm Hqvefnjpu Total power requirement: 52 kW Current type: 3 Ph Frequency: 50 Hz Operating voltage: 400 V Rated current: 99 A Overall width: 5,014 mm Machine width: 4,560 mm Depth without boom: 2,541 mm Depth with boom: 4,165 mm Height: 2,100 mm Total weight (without automation): 14,500 kg Drive power: 45 kW Hydraulic tank capacity: 1,000 l EQUIPMENT - Machine in horizontal design - Complete enclosure - Tailstock - Hydraulic system - Oil system

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: 109853 - 280028, workpiece diameter (max.): 38 mm, workpiece length (max.): 500 mm, TECHNICAL DETAILS EX-CELL-O Cold Rolling Machine with Felsomat (1999) Design: Horizontal Area of application: Chipless cold forming of profiles such as splines (straight or helical), spiral gears, oil grooves, CV joints, threads, and knurls Workpiece data Workpiece diameter: 38 mm Workpiece length: 500 mm Profile width: 92 mm Profile outer diameter (standard): 50 mm Profile width (standard): 125 mm Rollable profiles for involute gears: 0.3 - 1.25 m Rolling bar length: 610 mm Travel movements Cpedpfx Aswmb Trefnsu Slide stroke: 760 mm Cycle times Tailstock forward (at approx. 300 mm stroke): 1.0 s Rolling bars forward: 3.0 s Tailstock retraction (at approx. 300 mm) Stroke): 1.5 s Rolling bars return: 3.5 s Loading/unloading (manual): 5.0 s Cycle time: 14.0 s Gear cuts/hour at 100% Ne: 260 MACHINE DETAILS Overall width: 5,014 mm Machine width: 2,360 mm Depth without boom: 2,541 mm Depth with boom: 4,165 mm Height: 2,100 mm Machine weight: 10 t Electrical design – Voltage/Frequency: 380/50 V/Hz Total power requirement: 24 kW Drive power: 22 kW EQUIPMENT - Complete enclosure - Tailstock - Hydraulic system - Oil system

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, workpiece diameter (max.): 160 mm, rotational speed (max.): 300 rpm, workpiece length (max.): 25 mm, TECHNICAL DETAILS Description: Hydraulic internal rolling machine for tapered or cylindrical back rolling of profiles on sliding sleeves, sliding gears, or similar parts. Workpiece Data Workpiece diameter: 160 mm Workpiece length: 25 mm Workpiece internal gearing, adjusted approx.: 85 mm Workpiece external: 75 - 140 mm Workpiece width approx.: 16 - 36 mm Workpiece external pressure ring, adjusted: 160 mm Travel and setting data Maximum travel of the rolling carriage: 60 mm Center distance between workpiece and rolling wheel: 22 mm Rolling wheel speeds, continuously adjustable: 30 - 300 rpm Rolling pressure, continuously adjustable (at 100 bar): 6.1 t Control system: SIEMENS PLC Monitoring control: LAUER PCS 900 / BRANKAMP C 90 with screen display MACHINE DETAILS Machine weight approx.: 4,500 kg Space required approx.: 2.5 x 2.5 x 2.1 m Spindle drive approx.: 6 kW Total drive: 14 kW Total power requirement: 14 kW Operating voltage: 400 V Frequency: 50 Hz EQUIPMENT - Workpiece carousel loading device for 18 workpieces with workpiece inspection station - Workpiece transport device - Changeover time to a different workpiece size: 30 min / Machining time per workpiece approx.: 25 s - Workpiece storage for intermediate storage - Separate hydraulic system Cpodpowmb Rkofx Afneu - Separate control cabinet - Coolant system Note: Working areas are approximate and depend on the workpiece and tool conditions.

Condition: used, Thread rolling machine, cold rolling machine, thread rolling machine, profile rolling machine Manufacturer PEE-WEE Type P 24 Q serial no. LC2403099 year of construction 2004 Rolling force max. 24 ton. Tool diameter max. 200 mm Rolling spindle diameter 69,85 mm Tool bore diameter 70 mm (nominal diameter) Tool length, tool length max. 180 mm Workpiece diameter max. 50 mm Rolling spindle speed 22 - 44 - 95 - 190 rpm Motor power hydraulics approx. 3 kW Motor power roller drive 5.5 kW Mains connection 400 Volt, 50 Hz - Swivel roller spindle for threaded continuous rollers - Rolling spindle speed in 4 stages via gear changeover - Hydraulic system integrated in the machine bed Space requirement L x W x H 2000 x 1750 x 2550 mm Weight approx. 3 tons good condition Grooving rollers: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating into the workpiece up to the nominal diameter. The thread length is maximum as long as the rolling tools are wide. Continuous rolling: When the thread length is greater than the rolling tool width. Through-feed tools have 3 sections - the infeed, the calibration section and the outfeed. Grooved rollers have no pitch and are swiveled with the pitch angle of the profile to be rolled. Codpfsh A S Htsx Afnspu Pitch rollers differ from grooved rollers in that they have a pitch in the profile. The sum of the pitch angle and the swivel angle gives the pitch angle in the workpiece.

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece. Cpsdpfx Afsuz If Nenou

Condition: used, Mitre circular saw BERG & SCHMID type MKS 350 Year of construction approx. 1980 Sawing range at 90° round Ø 110 mm Sawing range for 90° rectangle 160 x 90 mm Sawing range for 90° square 95 x 95 mm Sawing area at 45° round Ø 95 mm Sawing area for 45° rectangle 120 x 90 mm Sawing area at 45° square 80 x 80 mm Saw blade diameter max. 350 mm Saw blade speed 28 and 56 rpm Motor power approx. 1.8 / 2.5 kW pole-changing Mains connection 380 Volt, 50 Hz - Motor with 2 electrically switchable speeds - Infinitely variable mitre quick adjustment up to 45° Cpedpfjquzd Rjx Afnju - Material vice with quick-release eccentric lever - Coolant device with electric coolant pump - material stop 350 mm - Saw blade with Ø 335 mm installed Space requirement L x W x H 1250 x 600 x 1200 mm Weight 240 kg good condition

Condition: used, saw blade diameter 400 mm cutting diameter 130 mm stroke 135 mm mitter cutting - all-position 0-45 ° turning speed range 1420 / 2840 U/min capacity 45 degrees: square 110 mm capacity 45 degrees: flat 50 x 240 mm capacity 90 degrees: flat 95 x 240 mm Csdpfjd Scrrox Afnjpu capacity 90 degrees: round 130 mm capacity 90 degrees: square 120 mm voltage 400 V total power requirement 3,7 / 4,5 kW weight of the machine ca. 600 kg dimensions of the machine ca. 1,15 x 1,20 x 1,60 m - Serial-No.: 102752 - cutting range round 130 mm - cutting range square 120 mm - cutting range flat 95 x 240 mm - vertical pneumatic clamping

Condition: used, Year of construction: 1998, saw blade diameter 450 mm cutting diameter 150 mm capacity 90 degrees: flat 330 x 40 mm capacity 45 degrees: round 140 mm capacity 45 degrees: flat 250 x 40 mm cutting speed 10 - 70 m/min saw head feed 0 - 1000 mm/min Cpsdev Hth Aopfx Afneu sawing motor 1,7 / 2,6 kW weight of the machine ca. 1,1 t Accessories: used sawblade 450 mmø, material feeder M 45 NC für autom. run, ingoing roller track 7000 mm, outgoing roller track 4000 mm

Condition: used, Year of construction: 1991, saw blade diameter 400 mm cutting diameter 130 mm capacity 90 degrees: square 120 x 120 mm capacity 90 degrees: flat 220 x 80 mm feed length 600 mm feed length: multiple 1800 mm cutting speed 10/13/15/20/26/30 m/min mitre joint cuts -/+ degrees 60 total power requirement 5,5 kW weight of the machine ca. 1,8 t dimensions of machine L x W x H 2,45 x 1,20 x 2,00 m - mitre cutting +/- 60 ° with DRO - Cpsdpfx Ajv Hhrvsfnsu Accessories: new sawblade 400 mmø, coolant

Condition: used, Year of construction: 1983, saw blade diameter 400 mm cutting diameter 130 mm stroke 150 mm cutting range - square - 120 x 120 mm cutting range - flat - 300 x 40 mm capacity 45 degrees: round 130 mm capacity 45 degrees: square 110 x 110 mm capacity 45 degrees: flat 245 x 40 mm mitter cutting - all-position 90 ° cutting speed 13 / 25 m/min Cedpfstqqrzsx Afnjpu control minipos 807 total power requirement 4,3 kW weight of the machine ca. 850 kg dimensions of machine L x W x H 1,20 x 1,20 x 1,82 m Accessories: ingoing and outgoing rollertrack each approx. 4000 mm long, NC length stop, coolant

Condition: new, ELMAG metal circular saw MKS 315 RLSS-N- SUPER-SET-ACTION SUPER-SET-ACTION - MKS RLSS-N standard equipment - Universal or sheet steel base - Material stand for circular metal saws - Quality saw blade HSS/DMo5 - Coolant concentrate 1:10, 5 liters Standard equipment - MKS RLSS-N metal circular sawing machine - Material support with roller - Bar stop with material stop - WSS quick angle clamp/angle scale - Adjustable cutting depth stop - DSS double quick-clamping vice - Quick clamping lever - Adjustable clamping jaw(s) - High-performance drive - Gearbox with permanent oil bath lubrication - Cooling system with diaphragm pump - ERGO operating lever with reset - Permanent safety switch on the handle - Self-closing saw blade guard - Emergency stop/zero voltage release - Tool/Operating instructions/CE ADVANTAGES High accuracy for series cutting - with bar stop and material stop Quick miter adjustment with a lever handle - with quick angle clamp and 45-0-45° angle scale Flexible miter setting - gear head and/or vice can be swiveled Cutting depth can be precisely limited - with cutting depth stop Powerful - two-speed drive motor 40/80 rpm Smooth-running and durable - quality gearbox with oil bath for permanent lubrication Optimum cooling - coolant circulation system with diaphragm pump, dosing valve and return filter Compact - coolant tank integrated in chip tray Stable cutting guide - with ERGO operating lever Safe - self-closing saw blade guard, permanent switch, emergency stop, zero voltage release, CE-compliant TECHNICAL DATA Round tube cutting range at 0° Max. 90 mm Round tube Cutting range at 45° right mitre Max. 80 mm Square tube Cutting range at 0° Max. 80 mm Square tube Cutting range at 45° right miter Max. 70 mm Cpjdpjt Hkbpsfx Afnou Rectangular tube Cutting range at 0° Max. 115x70 mm Rectangular tube Cutting range at 45° right mitre Max. 70x70 mm Saw blade outer diameter 315 mm Saw blade inner diameter 32 mm Vice clamping width max. 120 mm Cutting angle 45-0-45 ° Speed level 1 / 2 40 / 80 rpm Motor power speed level 1 / 2 1500 / 2200 W Mains connection 400/50 V/Hz Infeed height for roller conveyors 1030 mm Length 1475 mm Width 1000 mm Height 1150 mm Weight 150 kg

Year of construction: 2025, condition: new, Dimensions (L/W/H) 3480x1500x2000 mm Weight 5500 kg Total power requirement 2 kw Cedpfx Asv A Hk Nofnopu

Year of construction: 2025, condition: new, Dimensions (L/W/H) 4500x1500x2000 mm Weight 6500 kg Cpodev A Hmdjpfx Afnsu Total power requirement 2 kw

Year of construction: 2025, condition: new, Dimensions (L/W/H) 3750x1650x1970 mm Weight 5000 kg Total power requirement 6 kw Cjdpfjv A Hkpox Afnepu

Condition: good (used), Year of construction: 2008, Cutting range round Sawing capacity round 115 mm Max. Saw blade diameter Max. saw blade diameter 350 mm Cutting area rectangular Sawing capacity rectangular 200 x 70 mm Cutting area square Sawing capacity square 105 x 105 mm Sawing unit Sawing unit power 6.5/8 kw Saw shaft speed Speed on sawing shaft 1700/3400 rpm/rpm Maximum feed length Maximum feed length 9999 mm Shortest feed length Shortest feed length 10 mm Weight Weight 2300 kg Ausstattung / equipment: Cpjdpjrz Rw Rofx Afnou BEHRINGER SPS Steuerung / SPS Control Micro-Sprüheinrichtung / micro lubrication Controlled zero edge Cutting gap extension Maschinenleuchte / machine light Vertikale Hauptspannung / vertical main clamping Rücklaufsperre / non-return-device Extraction system prepared - (basement extraction unit is not part of the delivery) Roller conveyor infeed approx. 5000 mm -roller conveyor infeed selfmade length 5000 mm

Condition: used, Year of construction: 1987, rolling capacity max. NA t workpiece diameter 38 mm workpiece length 500 mm total power requirement 24 kW weight of the machine ca. 10 t dimensions of the machine ca. m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features * KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. * Originally, external gears were formed on the machine using pinion cages (no. of teeth = 25), Ø approx. 32 mm x 14 mm long, workpiece Ø approx. 80 x 80 mm long. Cpedpst Hw D Djfx Afneu * Various accessories: * Separate switch cabinet. * Separate hydraulic unit, 900 l. * Coolant device in the machine. * Control panel with malfunction message in plaintext, etc. Roto Flo machines are ideal for mass production of smaller gears/profiles. The coldforming process is a lot faster and more economical than other chip removing methods. Workpieces are clamped between 2 live centres and 2 synchronous opposed directional coldforming racks simultaneously engage the workpart and start rotation. During rotation, the profile is formed successively within one stroke. In the calibrating zone, the profiling and surfacing performance of the tool are optimised. Profiles do not require a run-out. The coldforming process requires a rigid and heavy duty construction of the machine, which ensures the required precision over the years. Between 25,000 and 100,000 working cycles can be performed with one set of racks, also for serrations. Condition : Very good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. We always have a good selection of gear machines available. Please let us know what you need.

Condition: good (used), Year of construction: 1996, CUTTING RANGE ..... MIN 10MM TO 75MM CUTTING LENGTH ..... 5-900 SINGLE STROKE -9999 REVERSE RUN Cpedpjquuufefx Afnju CUTTING SPEED ..... 0 - 40 MM SEC. INFINITELY VARIABLE REVERSE 135MM/S MATERIAL FEED SPEED ..... MAX. 350 MM/S TENSION FORCE ..... MAIN CLAMP 10500N

Condition: ready for operation (used), Year of construction: 1974, functionality: fully functional, machine/vehicle number: 817, Complete Cold Heading Line (includes 3 machines) One Die Two Blow Header Max. Wire Cut-Off Diameter: 25 mm Cpsdpfx Astqu U Tsfnsu Cut-off length: 300 mm Shaft Length Under head: 260 mm Extrusion machine Trimming machine