Used Edm Machine Edm for sale (64,853)

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Codpfx Asrtrzdskteri Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: good (used), Year of construction: 1998, grinding wheel diameter: 915 mm, overall weight: 14,000 kg, GIUSTINA Grinder R242 to ground big bearings (up to 800mm). All machine's actions are controlled by Bosch Control. Beside controlling parts grinding process, the NC programs are also an operator guide for the machine set up and a source of information about wheel wear, thus allowing the operator to check wheels without opening the hood. Equipped with: Bosch CNC Control Specifications: Wheel Rotation Axis: Horizontal Grinding Wheel Size (OD): 915 mm Crsdpfx Akortr D Ijtji Grinding Wheel Size, Usable Width: 65 mm Grinding Wheel Size, Peripheral Speed: 30 ms Spindle Motors: 75 kw Grinding Feedrate: 0.1 - 1000 mm/min Spindle Type: Moving Quill Angular Contact Spindle Bearings (Precision): ABEC-7 (ISO4) Slide Position Accuracy: 0.001 mm Coolant Flow Rate: 600 l/min Work Capacity (Approx) Rotary: 20 -200 Dia. In.

Condition: good (used), Year of construction: 1993, Equipped with: Credpfjruahwox Aktei 9" Cutter Head Power Stocks Crowning Auto Loader Heidenhein Scales Variable Feed/Speed Cutter Head RS232 Serial Port Trabon Lube Coolant W/Magnetic Chip Separator AC Servo Motors Full Splash Guards Stack Light Manuals Specifications: Work Gear Pitch Diameter 9" & 12" Cutter Head: 1-12", 1-8" Work Gear Max. O.D. 9" & 12" Cutter Head: 12 1/2", 8 1/2" Diameter Pitch Range: 4-20 Distance Between Centers: 23" Cutter RPM 9" & 12" Cutter Head" 50-500, 50-400 Max. Table Travel Conventional, Tangential, Diagonal: 5", 2" 5"-2" Diagonal Traverse Angle Straight Shaving: 0 Deg. - 90 Deg. Traverse Angle Crown Shaving: 45 Deg. Max. Approx. Max. Table Angle Crowning: 5 Deg. Max. Table Angle Taper: 1 Deg 30' Max. Cutter Head Crossed Axes Angle Left & Right: 25 Deg. Table Cross Feed Inches Per Minute: .5-35 Table Up-Down Feed Inches Per Minute: .004-12.5 Table Up-Down Travel: 8 1/8" Approx. Weight: 9600 lbs

Condition: excellent (used), Year of construction: 2008, MESPACK type H-180-FE powdered sugar bagging machine Year 2008 Filling in 2 stages 1 filler fills half, 2 filler fills other half Capacity: 50 bags per minute. Cartoning machine OTOR SYSTEMS type FCR 214 Capacity: 5 cartons of 10 bags per minute Year 2011 Csdpfx Ajtn Raroktori

Condition: used, machine/vehicle number: 008013, X axis working area: 5780 mm Y axis working area: 1650 mm Working Table: Pod and Rail Main Electrospindle power: 13.2 KW Number of controlled axes: 4 axes Maximum edge height: 60 mm Total number of drilling spindles: 16 Total number of tool changer positions: 16 Csdpowuz Eksfx Akteri

Condition: like new (used), Year of construction: 1998, Retrofitted: 2026 Numerical control: NUEVO/NEW HEIDENHAIN TNC-i640 Crsdpfxeyf Rqpe Aktoi Technical features Dimensions Table dimensions: 7650 x 1000 mmNumber of T slots: 7T slots dimensions: 22 mm Traverses of axis X axis traverse: 5850 mmY axis traverse: 1200 mmZ axis traverse: 1500 mm Milling head Head type: NEW Auto-indexing head UDG (every 2,5º)Tool clamping system: HydraulicTaper nose: ISO 50 (DIN 69871)   /   Pull stud: DIN 69872Speed range: 20 - 3000 rpmSpindle power: 29,6 kW Feedrates Rapid feedrates (X,Y,Z): 10000 mm/min Weight and dimensions Maximum weight on table: 4000 kg/m2Machine weight approx.: 31000 kgMachine dimensions approx.: 11590 x 5179 x 3485 mm Accessories Guarding: new perimetral wire-mesh fenceAutomatic tool changer: ATC-30Chip conveyor: rear longitudinalElectronic handwheel: New HR-510Coolant: external internal high pressure through spindle Sale conditions Warranty: 6 months mechanical partsPrice and sale conditions: On request View all technical features

Condition: used, Year of construction: 1972, bore capacity in steel (diameter) 50,0 mm arm length 1.350 mm workpiece height max. 1630 mm turning speeds 19 - 1320 U/min bore spindles - Morse Taper 5 MK engine output 5,5 kW weight 5 t range L-W-H 2,4 x 1,0 x 3,55 mm feed movement 475 mm floor plate size: 1650x1000 mm Cedpfxewiikdo Akteri feeds 0,07-2,9 mm/U

Condition: used, Year of construction: 1998, type of input current: three-phase, pressure: 7 bar, input voltage: 400 V, power: 6 kW (8.16 HP), No. 3290 4-head welding machine Urban AKS 1400/ETS Used, year of construction 1998 According to our customer / the previous owner, the machine is fully functional and can be inspected on site Vertical 4-head welding machine for PVC window profiles, welding all 4 corners at 90° in one operation Fully automatic cycle with automatic outfeed of the welded frame onto a conveyor Vertical/horizontal tilting unit, can be linked to a corner cleaning machine with turning station Electronic positioning of the X, Y1 and Y2 axes by servo motors (Lenze servo inverters) Urban IPC control with B&R Provit 2500 operator panel Extended working range, welding dimensions max. approx. 3850 x 2220 mm, min. approx. 355 x 320 mm Profile height 50 - 100 mm (clamping height SH 100) Profile width max. 130 mm, 150 mm on table side Weld bead limitation 2 mm Heating plates 200 x 295 x 15 mm with Teflon holder, temperature controller for each heating plate Adjusting plate 190 mm, welding stop 24.0 mm, loading stop 17.8 mm, left-hand stop Power supply 230/400 V / 50 Hz, rated power 6 kW Compressed air 7 bar Profile supports for SL 70 (outer frame, sash) and SL 82 (outer frame, sash, entrance door sash) Various spare parts (Lenze controller, brake, temperature controller) Crodpfxe Ah Un No Aktji Transport dimensions approx. 5400 x 2400 x 3100 mm LWH Weight approx. 2500 kg Sale on behalf of customer, ex location near 55120 Mainz, without dismantling, without transport and assembly Dismantling, loading, and transport by us optionally available Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical specifications, condition description, year of construction and scope of delivery according to manufacturer’s brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Photos and videos serve as examples and do not represent the actual scope of delivery Payment terms: Prices plus VAT, payment before collection or shipment Delivery terms: ex location

Condition: good (used), Year of construction: 2012, operating hours: 43,313 h, controller model: Siemens Sinumerik 840 D, laser power: 5,000 W, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Laser power: 5,000 watts Working area: 3,000 × 1,500 × 115 mm Max. sheet thickness, steel: 25 mm Max. sheet thickness, stainless steel: 20 mm Max. sheet thickness, aluminum: 20 mm Max. speed: 235 m/min Accuracy: 0.10 mm MACHINE DETAILS Cjdpfx Ako Ah Rl Ujtori Control model: Siemens Sinumerik 840 D Operating hours: 66,934 h / 43,313 h Dimensions & Weight Dimensions (L x W x H): 8,300 x 4,800 x 2,400 mm Weight: 12,000 kg EQUIPMENT Solid-state laser TruDisk 5001 with one LLK output Light guide cable according to standard layout Laser cooling unit (water-air) Excitation via pump diodes Laser power control Laser logbook function Universal cutting head with fully adaptive lens system Protective glass against lens contamination Condition monitoring of the protective glass ControlLine: Height control and sheet edge detection

Condition: good (used), Water conditioner for insulating glass production Ostmose plant Credpfx Aet Et I Aektji

Condition: excellent (used), USED HARTFORD HB2190AG FANUC 21iMB YEAR USED - ORIGINALLY BUILT 2009 MACHINE SN 12842 DOUBLE COLUMN, BRIDGE TYPE VERTICAL MACHINING CENTRE WITH HARDENED & GROUND BOX GUIDEWAYS FOR ENHANCED CUTTING PERFORMANCE MACHINE CONSTRUCTION FEATURES & EQUIPMENT  ONE PIECE HEAVY DUTY CAST IRON BED CONSTRUCTION.  HEAVY DUTY HARDENED AND GROUND BOX GUIDEWAYS.  FULL HEIGHT SPLASH GUARDING.  MODIFICATION TO SPLASH GUARD TO ACCOMMODATE 4.1 M LENGTH OF PART.  INTERNAL SPIRAL CHIP CONVEYORS.  LINK TYPE CHIP CONVEYOR AND CHIP BUCKET.  Z-AXIS NITROGEN COUNTER BALANCE SYSTEM.  HARTROL-FANUC 21iMB CNC SYSTEM.  25 BAR THROUGH SPINDLE COOLANT.  COOLANT GUN.  CE MARKED TABLE Working Surface 2,100 X 1,740 MM Tee Slot (Size x Number x Pitch) TBA MM Maximum Table Load 7,000 KGS TRAVEL Longitudinal Travel (X-Axis) 2,000 MM Cross Travel (Y-Axis) 1,970 MM Vertical Travel (Z-Axis) 920 MM Distance from Spindle Nose to Table 160 ~ 1,080 MM Distance from Spindle Centre to Column 430 MM Width between Columns 2,200 MM SPINDLE Spindle Nose Taper #50 - DIN69871 Maximum Spindle Speed 6,000 RPM GEARED Spindle Drive GEARED FEED Cutting Feedrate (X, Y & Z Axes) 1 ~ 7,000 MM/MIN Rapid Traverse (X-Axis) 10 M/MIN Rapid Traverse (Y-Axis) 10 M/MIN Rapid Traverse (Z-Axis) 10 M/MIN ATC Tool Storage Capacity ARM TYPE 40 STATIONS Maximum Tool Weight 15.0 KGS Maximum Tool Size Ø 125 X 350 MM Tool Shank DIN 69871 Pull Stud P50T-1 MOTORS Spindle Drive Motor (Fanuc) 26.0 KW POWER SUPPLY Cedpfxe Afnado Akteri Electric Power Consumption 50 KVA Air Pressure 6.5 KG/CM² Voltage 415V / 50HZ / 3PH MACHINE Floor Space (Fully Guarded) TBA MM Height TBA MM Weight 28,000 KGS

Condition: used, Year of construction: 2021, CNC MACHINING CENTER Morbidelli N100 KEY FEATURES "BUMPERS": THE PERFECT COMBINATION OF SAFETY AND PRODUCTIVITY "PRO-SPACE" SAFETY DEVICES: SAFE AND COMPACT "HE" TABLE - FOCUS: EFFICIENCY AND SAVINGS AXES Morbidelli N100 12 Morbidelli N100 15 Morbidelli N100 18 Morbidelli N100 22 Working area in X-Y-Z axis * mm 2486-1255-150 3686 TECHNICAL DATA -1555-150 3686-1860-150 22-31 = 30862185-150 22-43 = 42862185-150 Travel X-Y-Z axes mm 3120-1685-250 4320-1985-250 4320-2285-250 22-31 = 37702585-250 22-43 = 49702585-250 Traverse speed of X-Y axes m/min 35 WORK TABLE Type Multifunction table made of aluminum Stops for "A" working area No. 4 Vacuum pump (Opt.) m³/h 250/300 DRILLING UNIT Vertical spindles No. – RPM 7 (4X-3Y) 8000 – 12 (8X-4Y) 8000 Horizontal spindles (Opt.) No. – RPM 4 (2X-2Y) 8000 – 6 (4X-2Y) 8000 Integrated saw blade in X (Opt.) Ø mm – RPM 125 – 10000 Motor power kW (HP) 2.2 (3) ELECTROSPINDLE Motor power Std. (S6) kW (HP) 6.6 (9) – 9.5 (13) Max. speed RPM 24000 Lateral tool changer 8 positions 10 positions 11 positions 13 positions INSTALLATION Installed power kVA 23÷28.5 Compressed air requirement l/min 400 Extraction air requirement m³/h 5300 Extraction air speed m/s 30 Extraction nozzle diameter (electrospindle + drilling unit + kit) mm 250 Machine weight kg 1950 2200 2500 22-31 = 2550 22-43 = 3200 * X Distance between stops - Y Max. panel width - Z Workpiece passage only electrospindle or electrospindle + drilling unit: diameter 200 mm; Extraction air requirement 3,400 m³/h In conjunction with the strip for panel ejection, the extraction nozzle diameter is always = 250 mm GENERAL FEATURES CNC machining center for processing panel materials. Self-supporting structure and work table Box construction made of cold-rolled steel, consisting of rectangular sections welded together; multifunctional work table made of aluminum with a single working area. Holes in a grid of 120 mm for vacuum connection, easily removable via a magnetic device (patented system). The entire surface is grooved at a distance of 20 mm so that the workpieces can be clamped using rubber seals, MODULSET or suction cups. Automatically retractable reference stops that ensure accurate positioning of the workpieces to be machined. Moving gantry It is a gantry structure made of cold-rolled steel in a box construction, consisting of rectangular sections. The working units are installed on the gantry. Working unit consisting of a drilling head with vertical spindles, horizontal spindles, an integrated grooving and sawing unit and an SCM electrospindle with a quick-change tool system of type HSK63F. Travel of the gantry and aggregate carrier The movement in the X, Y and Z axis takes place on linear prismatic recirculating ball guides by means of pre-tensioned ball screws. The movement transmission of the X and Y axes (moving column and carriage) takes place via a reduction gearbox with rack and pinion drive. The movement of the aggregate carrier in the Z direction takes place via pre-tensioned ball screws. Positioning of the working units and control of the machine functions takes place via "Brushless" three-phase servo motors and digital control units. CONTROL The control unit consists of a numerical control. Csdpfez Iyvpex Aktjri

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Cedpfx Akexy Tmnotsri

Condition: used, Year of construction: 2016, Industrial automatic edge banding machine SOLUTION XD KEY FEATURES "E-TOUCH" CONTROL WITH AUTOMATIC PROGRAMMING: A SINGLE "TOUCH" IS ALL IT TAKES TO OPERATE THE MACHINE STANDARD PRESSURE DEVICE WITH DRIVE BELT FOR OPTIMAL PANEL GUIDANCE EDGE BANDING OF ROLL MATERIAL, STRIP EDGES AND SOLID WOOD EDGES GENERAL FEATURES Single-sided edge banding machine in left-hand version for edge banding of roll material and strip edges with all conventional hot melt adhesives. The base frame consists of a stable steel welded frame with higher rigidity, which provides optimal support for the installation of the processing units. The upper pressure beam consists of a thick-walled steel profile and a double trapezoidal drive belt, which is automatically positioned according to the panel thickness. Height adjustment with display on the upper pressure beam and on the operator panel. Manual workpiece feeding system with a large-sized work area and increased support surface facilitates the feeding of large workpieces. Adjustable infeed fence for two positions with automatic selection for processing with or without a pre-milling unit. Upper working units are attached to the pressure beam and mechanically connected to ensure automatic adjustment when changing panel thickness. Lower working units are attached to the machine frame or to the longitudinal support for precise referencing to the panel. All high-frequency motors are operated via frequency inverters. Each unit is equipped with its own inverter for optimal flexibility and improved machine production times. Protective hood for all units positioned after the glue application unit. Polycarbonate windows ensure a good view of the units during processing. Interior lighting of the hood. Protective hood with sound-absorbing material for lower noise emissions during operation. Spacer on the infeed fence allows the machine to be fed with the correct spacing. The spacing is automatically adjusted to the selected feed rate. Dust extraction port arranged on the pivoting control panel, positioned in the infeed area, is adjustable for ergonomic operation. The electrical system complies with current regulations. Electrical components are housed in a metal housing, attached to the machine frame and equipped with doors for easy access in case of maintenance. Standard voltage is 400 V EU 50 Hz (with neutral conductor). Material feed is via a feed chain with 80 mm wide chain plates made of rubberized nylon, for optimal guidance and high load capacity. The chain slides on 2 guides made of hardened and ground steel, one round and one flat guide, to guarantee straight feed and to protect against lateral displacement. Automatic chain lubrication. The amount of lubricating oil is optimized by the control system depending on the panels being processed. External support roller track positioned along the entire length of the machine; consisting of an extendable opening system up to 650 mm (for panels with a maximum width of 1200 mm). E-TOUCH PC control system for quick and easy execution of the main functions of the machine. Includes: – Processing of programs in Just in Time mode – Possibility of management via bills of materials – Possibility of management by Cjdpfx Aoxy Tm Ijktori

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, travel distance X-axis: 1,660 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 510 mm, controller model: Mazatrol M+, spindle speed (max.): 7,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 1,660 mm Travel range, Y-axis: 510 mm Travel range, Z-axis: 510 mm Table dimensions: 2,000 × 510 mm Table load capacity: max. 1,000 kg Spindle speed: 7,000 rpm Crsds Ah H Ihspfx Aktoi Tool holder: SK 40 Tool magazine: 48 tool positions MACHINE DETAILS CNC control: Mazatrol M+ Machine weight: approx. 7,500 kg EQUIPMENT Chip conveyor: MAYFRAN 4th axis with rotary indexing table: Rotamatik RM 100

Condition: good (used), Year of construction: 2013, Ref. -No.: 10718 Manufacturer: REIDEN Type: RX 10 Year of construction: 2013 Type of control: CNC Control: Siemens Sinumerik 840 D Storage location: Halberstadt Country of origin: Schweiz Machine-No.: 40-xxx Turning Speeds: 16.000 RPM X stroke: 1.000 mm Y stroke: 1.100 mm Z - stroke: 810 mm C-Axis: 360° Spindle power: 38 kW Tool Taper: HSK 63 Max. Rapid traverse: 60 m / min Cjdpfx Aks Ahw Sietori Further information: The machine is offered including all available accessories and technical documentation. The machine has been cleaned, is fully operational and can be inspected under power by prior appointment.

Condition: excellent (used), Year of construction: 2010, Control system: Heidenhain TNC 124 Travel distances X / Y / Z: 600 / 400 / 400 mm Clamping area: 800 x 425 mm Tool holder: SK 40 Tool clamping: hydraulic Spindle speed: 1 – 4500 rpm Crodpfs Ahw E Djx Aktji Feed rates: 0 – 2000 mm/min Rapid traverse rate X + Y: 5000 mm/min Rapid traverse rate Z: 4000 mm/min Tailstock, vertical travel: 60 mm Weight: approx. 2000 kg

Condition: new, Year of construction: 2026, Ref. -No.: 10464 Manufacturer: IGREK Type: 3500 XXL Year of construction: 2026 Type of control: CNC-Steuerung Control: Siemens 840 D / Heidenhain iTNC 640 Storage location: Istanbul Country of origin: Türkiye X-Travel: 10500 mm Y-Travel: 3500 mm Z-Travel: 1400 mm A-Axis: +/- 115 ° B-Axis: 360 ° Max. Torque: 235 Nm Rapid Traverse X/Y/Z: 30 m / min Drive power spindle: 54 kW Table load max.: 4000 kg Tool Taper: HSK-A100 Spindle Speeds: 12500 RPM Machine length: 16000 mm Machine width: 7400 mm Machine Height: 8500 mm Weight: 195 t Further information: GREK 3500 XXL – Customized precision for large-scale projects The IGREK 3500 XXL is a CNC 5-axis portal milling machine of the latest generation, developed for the high-precision machining of large components. Built in 2024, it is ready for immediate use and equipped with the latest technology to meet the most demanding requirements in heavy industry and mechanical engineering. Key features: Gigantic machining areas: With travel distances of 10,500 mm (X), 3,500 mm (Y) and 1,400 mm (Z), the machine offers extraordinary flexibility for machining large parts. 5-axis simultaneous machining: The A-axis with +/- 115° and the B-axis with 360° guarantee maximum precision and versatility when machining complex workpieces. Powerful spindle: Equipped with a speed of up to 12,500 rpm, a maximum torque of 235 Nm and a drive power of 54 kW – ideal for high-performance machining. Robust and durable: Weighing 195 tons and with a table load of up to 4,000 kg, the machine is designed for heavy-duty machining. Innovative tool holding fixture: The HSK-A100 tool holding fixture enables quick tool changes and increases efficiency. Speed and efficiency: Rapid feed rates of 30 m/min on all axes ensure maximum productivity. Technical data at a glance: Traverse paths: X 10,500 mm / Y 3,500 mm / Z 1,400 mm Spindle power: 54 kW Spindle speed: 12,500 rpm Table load: up to 4,000 kg Machine dimensions (LxWxH): 16,000 x 7,400 x 8,500 mm Weight: 195 tons Additional benefits: The machine is supplied with the advanced Siemens 840D or Heidenhain iTNC 640 control system and offers worldwide warranty and service support from the manufacturer. Choose the IGREK 3500 XXL for precision and efficiency in the machining of large parts. Contact us now for a non-binding offer! Crsdpfx Akjxc Tr Astsi

Condition: good (used), functionality: fully functional, For sale is a used, custom-built box-clamping machine for the production and assembly of wooden boxes. The system is equipped with a total of 6 hand-operated clamping devices from the Senco brand. The clamping devices are activated via foot valves, allowing the box parts to be positioned and clamped together during the work process. Particularly suitable for the production of wine boxes, fruit boxes, vegetable boxes, and other wooden packaging. Technical data / equipment: Manufacturer: Custom-built Machine type: Box-clamping machine / Box assembly machine 6 hand-operated clamping devices Clamping device manufacturer: Senco Activation via foot valves Pneumatic operation For clamping box parts together Workpiece support / workbench Adjustable fixture for different box dimensions Robust frame construction Suitable for: Wine boxes Fruit boxes Vegetable boxes Packaging boxes other wooden boxes and wooden packaging The machine is in used condition. Equipment and condition as shown in the photos. Transport is possible for an additional charge! Cjdpfezynf Sjx Aktori The machine is currently still at the customer's site but would be available shortly. The machine will be inspected before sale. For used machines with a year of manufacture of 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sale, and changes are subject to change. All information is without guarantee.

Condition: good (used), Year of construction: 2012, Ref. -No.: 10469 Manufacturer: JAESPA Type: Comfort 420 A Year of construction: 2012 Type of control: N/A Control: N/A Storage location: Halberstadt Crjdpfx Asy Ed D Dektsi Country of origin: Germany

Condition: good (used), Year of construction: 1990, Ref. -No.: 10544 Manufacturer: DECKEL Type: KF 2 Year of construction: 1990 Type of control: N/A Control: N/A Storage location: Halberstadt Country of origin: Germany Power Capacity: 1,6 / 2,0 kW Tool Taper: 20 mm Ø Space requirements: 1600 x 1350 LxWxH (mm) Feed rate: 0-350 mm / min Vertical portal passage, clamping table - lower beam cross member: 300 mm Distance table - spindle nose with vertical milling spindle: 50 mm Distance table - spindle nose with horizontal milling spindle: 450 mm Machine Height: 1950 mm Weight: 2,1 t Pre-milling spindle: 80...1000 min-1 Collets: 20 O taper bushing: Morse 1 Touch lift: 12 O Speed of the milling motor: 1400 RPM Further information: - Optical testing device - Pre-milling spindle - Model milling device - Rotary table - Inclined spindle - Mirror image milling device - Reduction and enlargement device - Roller engraving devices - Machine vice hydraulic clamps - Auxiliary clamping table - Dividing head Csds Ahmu Espfx Aktori - Tool cabinet - Clamping claws - template bars - articulated light The machine can be viewed under power by arrangement.

Condition: used, Year of construction: 1999, CNC machining center Manufacturer: Homag Type: BAZ 31/60/K Optimat Year of manufacture: 1999 Technical data - Workpiece length max. 6600 mm with single workpiece placement max. 2700 mm with alternating workpiece placement - Workpiece width max. 1200 mm - Workpiece thickness with edge max. 60 mm without edge max. 60 mm with standard clamp without edge max. 120 mm with clamping template when chamfer milling min. 12 mm when radius milling min. 2x radius + 10 mm - Working height, lower edge of workpiece 950 mm - 2 vacuum pumps, each with 66/100 m3/h for clamping system Main spindle 12 kW, water-cooled - for HSK F63 - Three-phase asynchronous motor 12 kW at S1, 600 Hz - Speed range: 1500 - 18000 rpm - Tool weight max. 6 kg incl. tool holder Tool changer, 12 positions - for tools and aggregates with HSK F63 - 12 x diameter max. 130 mm or - 6 x diameter max. 180 mm and 6 x diameter max. 70 mm - Tool diameter for grinding tools max. 200 mm Aggregate interface BAZ for main spindle For accommodating the machining and gluing aggregates with integrated pneumatic-electrical-electronic supply and pivoting drive, C-axis. Swiveling range without limitation. Hose-free compressed air supply. Drilling head with 17 spindles - 1 motor 1.9 kW, frequency-controlled - Speed selectable via program 4500/6500 or 8000 rpm - Each spindle can be activated individually Cedpfx Ae Ahmz Doktjri - Arrangement of spindles in T-shape. - 11 spindles in X-direction, 7 spindles in Y-direction Homatic control system CNC programming system WOODWOP Postprocessor Programming based on CNC drawing Laser positioning aid for vacuum clamping system Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: good (used), Year of construction: 2012, Ref. -No.: 10659 Manufacturer: DECKEL MAHO Type: DMC 835V Year of construction: 2012 Type of control: CNC Control: Haidenhein iTNC 530 Storage location: Halberstadt Country of origin: Germany Machine-No.: 1541XXX X-Travel: 835 mm Y-Travel: 510 mm Z-Travel: 510 mm Number of T-slots: 5 Max. Tool Weight: 6 kg Max. Tool Length: 250 mm Max. Tool Diameter: 80 mm Tool change time: 1,6 s T - groove width: 14 mm T - slot spacing: 100 mm Tool Taper: SK40 Numbers Of Tools In Magazin: 30 Spindle Speed: 12000 RPM Max. Torque: 130 / 87 Nm Turning Speed Range - Stepless: 30 mm / min Total Power Requirement: 35 kW Dimensions Of The Machine Ca.: 4,5 x 3,5 x 2,7 m Weight Of The Machine Ca.: 5 t Changeover time chip - chip: 6 sec Feed rate: 1 - 20.000 (X / Y / Z) High pressure cooling: 20 bar Further information: The machine can be inspected while powered on by prior arrangement. Csdpfjzw Tw Ujx Aktjri

Condition: used, Year of construction: 1954, functionality: fully functional, grinding length 600 mm Csdpfevu Hkyex Akteri grinding width 205 mm x-travel 600 mm ja

Condition: used, Year of construction: 1988, Bed milling machine Manufacturer: Correa Type: A16 Year of manufacture: 1988 Control: HEIDENHAIN TNC415 Credpozt U T Asfx Aktsi Travel distances X/Y/Z: 1,800 x 800 x 800 mm Clamping area: 2,000 x 630 mm Workpiece weight: 3,000 kg Operating hours: 12,103 Power: 19 kW Spindle type: ISO 50 Dimensions L/W/H: 4,886 x 2,720 x 2,500 mm Machine weight: 7,500 kg 31126