Used Eitec Gmbh for sale (69,809)

Condition: new, The unit is new, complete including controls, diesel tank, exhaust and batteries. Description Model: NWR35 Ricardo Motor Newpower generator generator set Continuous power: 24 kW / 30 kVA Maximum power: 26kW / 33kVA Engine : Kofo RIcardo N4100DS-30, 4 cylinder water-cooled Connection: circuit breaker Frequency : 50 Hz. Voltage: 400/230 V including mechanical speed control, AVR, battery charger, galvanized soundproofing, cooling water heater, Control unit: Comap AMF8, mains feed Dimensions: 2180x960x1260 mm Weight: approx. 900kg Diesel tank: 102 L. At 100% load: 7.15 L/h At 75% load : 5.8 L/h At 50% load : 3.7 L/h Mains monitoring, mains feed, soundproofed Ready for immediate use. Net price: €5,208, gross price: €6,197 additional costs 63A automatic switch: € 500 100A automatic switch: € 620 Shipment: - Worldwide transport including unloading is possible for an extra charge - In order to be able to quote an exact freight price, please send us a request with your data and your complete address -Available from April Tedpfx Aekh Hbpsqxja

Condition: new, The unit is new, complete including controls, diesel tank, exhaust and batteries. Description Model: NWR35 Ricardo Motor Newpower generator generator set Continuous power: 24 kW / 30 kVA Maximum power: 26kW / 33kVA Engine : Kofo RIcardo N4100DS-30, 4 cylinder water-cooled Connection: circuit breaker Frequency : 50 Hz. Voltage: 400/230 V including mechanical speed control, AVR, battery charger, galvanized soundproofing, cooling water heater, Control unit: Comap AMF8, mains feed Dimensions: 2180x960x1260 mm Weight: approx. 900kg Tsdpfx Aqsn D E Iqjxoa Diesel tank: 102 L. At 100% load: 7.15 L/h At 75% load : 5.8 L/h At 50% load : 3.7 L/h Mains monitoring, mains feed, soundproofed Ready for immediate use. Net price: €5,208, gross price: €6,197 additional costs 63A automatic switch: € 500 100A automatic switch: € 620 Shipment: - Worldwide transport including unloading is possible for an extra charge - In order to be able to quote an exact freight price, please send us a request with your data and your complete address -Available from April

Condition: new, Newpower Generator proudly presents its new NWK22 Soundproof Plus series. These gensets are equipped with extra sound curtains in the cabins, which guarantees a 15 percent reduction in noise level compared to the standard series. The genset is new, complete with controls, diesel tank, exhaust batteries, AVR, battery charger, cooling water heater, sockets, RCD protection circuit breaker. - Reinforced sound insulation - Extra quiet operation - Mains monitoring, mains supply - Immediately ready for use Technical data: Model: NWK22 Soundproof Plus Emergency generator Fawde Motor Newpower genset with extra soundproofing Engine : Fawde 4DW91-29D, 4 cylinders, water cooled Generator : Newpower NW/N22 Continuous power: 16 kW / 20 kVA Maximum power: 18 kW / 22 kVA Noise level (7m): 62 dB Connection:1x5P 63A -, 1x5P 32A -, 2x5P 16A-, 2x2P Schuko sockets, FI protection circuit breaker Frequency : 50 Hz Voltage : 400/230 V RPM : 1500 rpm Control : Comap IL4 AMF8 Year of manufacture : 2023 Dimensions (LxWxH) : 2170x 930 x 1400mm Weight: 930 Kg Diesel tank: 95 L. ( Possibility to connect to external tank) 100% load approx. 5,0 l/h 75% load approx. 3,9l/h 50% load approx. 2,7l/h Tjdpfxol Ixzlo Aqxja Price: 6.100,00 € + 19% VAT = 7259,00 € invoice with VAT will be issued additional costs 63A Automatic changeover switch: € 500 100A Automatic changeover switch: € 620 Shipping: - A worldwide transport incl. unloading is possible for an additional charge. - To be able to quote an exact freight price please send us an inquiry with your data and your complete address Legal information

Year of construction: 2025, condition: new, functionality: fully functional, The universal laser marking system LAS 28 XLe from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes an integrated PC with Windows operating system and laser software. Optionally, the laser model LAS 28 XLe can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realized. Made in Germany Fiber laser 30W, 20 W or 50 Watt - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - marking software EZCAD in German / English - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - pilot laser (simple preview, contour preview) Tedpjxd A I Aefx Aqxsa - focus finder (simple focus adjustment) - signal light for indication of operating status - max. component height approx. 300mm - electrically adjustable Z-axis - Integrated PC with Windows operating system - frame made of aluminum profile - air cooled - Door width approx. 700mm / door height(pass-through): 400mm - Connection 230V - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) - Weight: approx. 100 Kg

Condition: new, Year of construction: 2026, functionality: fully functional, input voltage: 230 V, type of input current: AC, laser power: 30 W, type of cooling: air, total width: 400 mm, total height: 690 mm, total length: 600 mm, overall weight: 45 kg, height adjustment type: electric, scan area length: 110 mm, scan area width: 110 mm, space requirement height: 900 mm, laser wavelength: 1,064 nm, ambient temperature (min.): 15 °C, ambient temperature (max.): 35 °C, input frequency: 50 Hz, laser type: fiber laser, The LAS 22 is a compact tabletop unit with a small working area, ideally suited for small parts. Due to its small size, the unit is very practical and can be used anywhere. The device is very easy to operate without programming knowledge Todpfx Aey I Nbmsqxja - Fiber laser 30 Watt (Optional: 20 Watt, 50 Watt) - Laser class 1 - Wavelength 1064nm - Marking field size 110 x110mm - marking software EZCAD in German / English - Pilot laser (simple preview/contour) - Focus finder (simple focusing) - Max. Component height approx. 95 mm - Grid holes for fixtures - Clamping area 310x190mm - Electrically adjustable Z-axis - Electric door with anti-trap protection - optional: exhaust system (incl. activated carbon filter) - Welded steel plate construction - Connection 230V - Air cooled - Laptop with Windows operating system (German or English) - dimensions: LBH 600x 400x 690 mm - weight: approx. 45 Kg - low operating costs - marking of various materials

Condition: new, Year of construction: 2026, functionality: fully functional, shaft length: 1,064 mm, input voltage: 230 V, type of input current: AC, laser power: 30 W, type of cooling: air, total width: 1,500 mm, total height: 2,050 mm, total length: 900 mm, working range: 600 mm, overall weight: 120 kg, warranty duration: 12 months, height adjustment type: electric, door opening width: 700 mm, door opening height: 400 mm, scan area length: 150 mm, scan area width: 150 mm, table length: 600 mm, table width: 600 mm, space requirement width: 1,550 mm, space requirement height: 2,100 mm, laser wavelength: 1,064 nm, working height: 950 mm, input frequency: 50 Hz, The universal laser marking system LAS 28 XLe from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes integrated PC with Windows operating system and laser software. Optionally, the laser model LAS 28 XLe can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realized. Made in Germany Fiber laser 30 Watt, 20 Watt or 50 Watt - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - Signal light for displaying operating status - optional: rotary axis (3-jaw chuck) - optional: extraction system (incl. activated carbon filter) - optional: digital height measuring system - optional: autofocus - EZCAD marking software in German / English (other software available on request) - Pilot laser (simple preview, plain text preview) - Focus finder (simple focus adjustment) - max. component height approx. 300mm Tsdpfxey T Ixno Aqxoa - Electrically adjustable Z-axis - Integrated PC with Windows operating system - Height-adjustable screen and keyboard support - Frame made of aluminum profile - Air-cooled - Door width approx. 700mm / door height (pass-through): approx. 400mm - 230V connection - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) with screen holder approx. 1500 x 800 x 1900mm (LxWxH) - Weight: approx. 120 kg

Year of construction: 2026, condition: new, functionality: fully functional, overall weight: 100 kg, total length: 800 mm, total width: 600 mm, total height: 1,660 mm, input voltage: 230 V, input frequency: 50 Hz, laser power: 20 W, laser wavelength: 1,064 nm, type of cooling: air, laser type: fiber laser, The universal laser marking system LAS 28 from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes a laptop incl. holder with Windows operating system. Optionally, the laser model LAS 28 can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extensions for marking long parts, can be realized. Made in Germany Tsdpfxjv Sybys Aqxea - Fiber laser 20W (Optional: 30W, 50W) - Wavelength 1064nm - marking field size 150x150mm (optional: 200x200) - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - optional: Autofocus system - signal light for indication of operating status - marking software EZCAD (optional additional laser software) - Pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - max. part height approx. 270mm - electrically adjustable Z-axis (adjustment of working plane) - frame made of aluminum profile - connection 230V - air cooled - Laptop with Windows operating system - dimensions: 800x 600 x 1660mm (LxWxH) - weight: approx. 80 Kg

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, measuring range X-axis: 900 mm, measuring range Y-axis: 1,500 mm, measuring range Z-axis: 700 mm, Equipment: type plate available, Zeiss CNC coordinate measuring machine Prismo 9/15/7 VAST GOLD Tjdpfx Ajzq U Rcjqxsa Year of manufacture: 2000 Retrofit 2024, last DAkkS calibration 12/2021 Measuring range: X = 900 mm, Y = 1500 mm, Z = 700 mm In excellent technical and optical condition Device features, equipment: C99 control system with BP26 operating panel Automatic temperature compensation VAST GOLD sensor system Probe changer magazine MSR, 10-position VAST Probe changer plate, 8x VAST Reference probe Temperature probe Probe accessories Calibration sphere HP Z4 workstation with WIN11 and monitor Calypso Basic 2024 software Options: Curve and QS-Stat Calypso upgrade and other options possible Further accessories and options available Available for immediate delivery

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, power: 0.14 kW (0.19 HP), input voltage: 230 V, type of input current: AC, volume flow: 1,890 m³/h, filter area: 7.9 m², noise level: 65 dB, actuation type: electric, total height: 575 mm, total length: 600 mm, total width: 590 mm, overall weight: 55 kg, Equipment: CE marking, documentation/manual, LTA electrostatic extraction system 2 units, left and right intake The intake nozzle can be screwed on as needed; currently, there are none, as it was previously mounted directly on the housing wall. In very good, fully functional condition; naturally, it has been completely cleaned. Tsdpfxszqttce Aqxja Available for immediate delivery.

Condition: used, Year of construction: 2013, functionality: fully functional, machine/vehicle number: NS-009-0000-300, type of input current: AC, nominal power at 50% duty cycle: 250 kVA, throat depth: 300 mm, short-circuit current: 50,000 A, input voltage: 400 V, type of cooling: water, total width: 1,000 mm, total length: 1,000 mm, total height: 1,850 mm, overall weight: 1,000 kg, open-circuit voltage: 22 V, Zens Multifunction Resistance Welding Machine 250 kVA MF – 23 kN – 50 kA – Year of Manufacture 2013 For sale is a high-quality Zens multifunction resistance welding machine in a robust industrial design. The system was developed for demanding resistance welding processes and is ideally suited for series production in the automotive, supplier, electrical, and metal industries. The machine operates with modern medium frequency (MF) technology and achieves a welding power of 250 kVA at a 50% duty cycle. The powerful SER medium frequency inverter (700 A) enables a maximum welding current of 50 kA and ensures maximum process stability as well as reproducible welding results. With a maximum welding force of 23 kN and an overhang of 300 mm, the system is suitable for a wide range of resistance welding applications. Technical Data Manufacturer: Zens Machine Type: Multifunction Resistance Welding Machine Year of Manufacture: 2013 Welding Power: 250 kVA (Medium Frequency / MF) at 50% duty cycle Max. Welding Current: 50 kA SER Medium Frequency Inverter: 700 A Welding Control: SER-Mega1 Maximum Welding Force: 23 kN Overhang: 300 mm Equipment CE-compliant protective enclosure CE safety light curtain Welding table for welding forces up to 23 kN Pressure compensation tool QSF-M quality assurance system Position measuring system for process monitoring PLC control (Siemens S7) Robust industrial design for continuous industrial operation Tsdpfx Aszqucfeqxea The combination of powerful medium frequency technology, precise force and position control, and modern PLC and SER welding control ensures high process reliability and consistently reproducible welding results. Thanks to the complete CE safety equipment, the machine can be easily integrated into existing production lines. The system is in good condition and can be inspected and demonstrated at any time by prior appointment.

Condition: excellent (used), functionality: fully functional, Year of construction: 1996, Capacity: 1040 x 3.5 mm - Light gauge sheet metal protection at the rear - Ortlinghaus brake and clutch combination - Tilting roller table or sheet metal lifting system with plastic rollers - Central lubrication system Tsdjzq Uvxjpfx Aqxoa

Year of construction: 2016, condition: ready for operation (used), Volume Chamber I/ Chamber II: 2970/ 378l, maximum permissible operating pressure Chamber I/ Chamber II: 0/ 3.0bar, maximum permissible operating temperature Chamber I and Chamber II: 100°C, test pressure Chamber I/ Chamber II: 0/ 4.5bar. An on-site inspection is possible. Tedszq Ebxepfx Aqxsa

Year of construction: 1984, condition: ready for operation (used), Maximum volume Chamber I/Chamber II: 580/173 l, maximum permissible operating temperature Chamber I and Chamber II: 80°C, maximum permissible operating overpressure Chamber II: 2 bar. An on-site inspection is possible. Tsdpfx Aqjzq Eccexoa

Condition: like new (used), operating hours: 1,430 h, Sausage filling machine, piston filling machine Rex Type RKF 130 for filling/portioning & cutting, completely made of stainless steel. Todpfx Aqszqup Ssxea Condition: Like new.

Condition: used, Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Tjdpfey Urtfox Aqxea Replacement of all plastic sliding plates for the hydraulic push floor. Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. All six limit switches (proximity sensors) on the push floor were replaced. The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2023, condition: used, Mobile sealing machine with vacuum and protective gas function Manufacturer: BS Verpackung GmbH & Co. KG Model: BS25 Basic Year of manufacture according to nameplate: 2023 Maximum sealing area: 365 × 280 mm Maximum tray height: 115 mm Cycles: 1.5 / min. (depending on the set process parameters) External dimensions: 560 × 970 × 1450 mm (W x D x H) Maximum film width: 380 mm Compressed air connection: 6 bar Vacuum pump: 25 m³/h Weight: 180 kg Power connection: 1 phase, 230 / 400 V, 50 Hz Power consumption: 2.1 kW Sealing types: Sealing / Vacuum / Gas Features • Service-friendly design • Quick-change system for the sealing unit • Powerful Busch vacuum pump • High-quality sensor control • Precision cutter for clean contour cutting • Very quiet, sound-dampened compressed air compressor Purchase price (net): €10,500 plus legally applicable VAT. Value-added tax will be shown separately on our invoice. Subject to changes, errors and prior sale. Sale is made without warranty and guarantee and only to business customers. Todpfszp Umhex Aqxoa Inquiries will be processed from Monday to Friday between 8 a.m. and 4 p.m.

Year of construction: 2021, condition: good (used), Styrofoam press / compact screw compactor for EPS (Styrofoam®) and XPS, EPS packaging or production waste, Heger – used: Price ex works: only €9,950 (net)! Manufacturer: Heger GmbH, Herrenberg Type: Tiger 130 T Year of manufacture: 2021 3x400V, former new price: EUR 15,000 Throughput 1) up to 15 kg/h Achievable compression 1) up to 250 kg/m³ Processable material densities up to 30 g/l Processable molded part height up to 300 mm Effective feed opening (W x D) 700 x 360 mm Block size 130 x 130 mm Tjdpszk Da Hefx Aqxoa Installation dimensions (L x W x H) 2,824 x 440 x 1,602 mm Machine weight 310 kg Electrical connection power 1.5 kW Supply voltage (EU) 3 x 230 V 50 Hz 3 x 400 V 50 Hz Supply voltage (USA) 3 x 230 V 60 Hz 3 x 480 V 60 Hz CE marking Condition: good – very good, little use Available: immediately Location: 25813 Husum

Year of construction: 2025, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: R500, FiberFlow R500 Cooling Die for Sale Todsy Um Tgopfx Aqxsa The FiberFlow R500 Cooling Die is a specially developed solution for structuring alternative proteins in High Moisture Extrusion (HME). The cooling die is designed to produce fibrous protein structures through controlled cooling and optimized flow guidance, making it particularly suitable for applications such as plant-based meat and seafood alternatives, as well as structured convenience products. The FiberFlow R500 is designed for throughput rates of up to 500 kg/h at operating pressures of up to 70 bar. Its annular (ring-shaped) geometry ensures optimal flow distribution, resulting in uniform fiber formation and consistently high product quality. The system features a modular design and is sold as a complete unit consisting of four segments. Particular emphasis has been placed on hygienic design, enabling the system to meet the stringent requirements of the food industry. The construction allows for easy and efficient cleaning. The FiberFlow R500 is designed for seamless integration into existing extrusion lines and can be incorporated into continuous production processes without difficulty.

Year of construction: 2026, condition: new, functionality: fully functional, input voltage: 230 V, input frequency: 50 Hz, laser power: 20 W, laser wavelength: 1,064 nm, scan area length: 110 mm, scan area width: 110 mm, type of input current: AC, laser type: fiber laser, The LAS 22 is a compact tabletop unit with a small working area, ideally suited for small parts. Due to its small size, the unit is very practical and can be used anywhere. The device is very easy to operate without programming knowledge - Fiber laser 20 Watt (Optional: 30 Watt) - Laser class 1 - Wavelength 1064nm - Marking field size 110 x110mm - marking software EZCAD in German / English - Pilot laser (simple preview/contour) - Focus finder (simple focusing) - Max. Component height approx. 95 mm Tsdpfx Aqsw Et Iljxsa - Grid holes for fixtures - Clamping area 310x190mm - Electrically adjustable Z-axis - Electric door with anti-trap protection - optional: exhaust system (incl. activated carbon filter) - Welded steel plate construction - Connection 230V - Air cooled - Laptop with Windows operating system (German or English) - dimensions: LBH 600x 400x 690 mm - weight: approx. 45 Kg - low operating costs - marking of various materials

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: 2132072, REF: MM6195 1 x Foodlogistik GmbH high-capacity dicing machine supplied with dicing multigrid. This is a fantastic high-throughput dicer for dicing fresh, tempered and cooked meat, poultry or fish. Can also be used for cheese, vegetables and fruit. Technical specification ⚙️ ✅ Manufacturer - Foodlogistik GmbH ✅ Model - DICR CAPACITY 126. ✅ Serial number - 2132072. ✅ Date of manufacture - 2013. ✅ Throughput / capacity - up to 3,000 kg/h depending on product. ✅ Product temperature range - -3C to +60 C. ✅ Chamber dimensions - 530mm long x 126mm wide x 126mm high. Tsdpjxfll Tsfx Aqxja ✅ Electrical requirements - 400-415 V / 50 hz / 3 phase. ✅ Power - 5.6 kW. Dicing grid - multigrid, currently set up for 10mm cubes. ✅ Condition - very good, last used in June 2025.

Year of construction: 2026, condition: new, functionality: fully functional, For sale: skip with steel lid, 3000 x 2000 x 1250 mm Product description: For sale is a skip with a steel lid, 3000 x 2000 x 1250 mm, ideal for the transport and storage of waste, bulk materials, or industrial materials. The container is robust, safe, and ready for immediate use. Tjdpfxszq E R Tj Aqxoa Technical specifications: - Base: 3 mm - Sides: 3 mm - Steel lid: 2 mm - Frame, C-profile: 80 x 50 x 4 - Fasteners for transport, made of 6 mm sheet metal - Drain valve in the base of the container - Transport with a forklift is possible along and across the container - Transport with a crane is possible - Warning stickers: white and red - The entire range of RAL colors is available - Interior and exterior: zinc phosphate primer, exterior painted with synthetic resin paint (80-100 μ) Certificate: CE Warranty: 2 years Advantages: - Robust construction for heavy materials - Easy handling thanks to sturdy hinges - Stackable - Weather-resistant due to corrosion-resistant coating

Condition: new, Bee GTE-88/090/-08-V17-F pneumatic ball valve, 24V DC coil voltage, unused, 100% functional, scope of delivery as shown in the photos. Tjdpfsi D T Iysx Aqxja

Condition: good (used), Year of construction: 2022, functionality: fully functional, overall weight: 125 kg, input voltage: 230 V, total length: 1,500 mm, total height: 1,000 mm, total width: 700 mm, Equipment: documentation/manual, Siemens S7 PLC training and testing system AP2, electronics technician for automation technology – conveyor system Manufacturer: Stepp Fabrikautomation GmbH & Co. KG Year of manufacture: 2022 Control system: Siemens S7 PLC Todpjzp Iqmsfx Aqxsa Description: For sale is a complete, professionally manufactured training and testing system for training in the field of electronics/automation technology. The system was manufactured by Stepp Fabrikautomation GmbH & Co. KG as a special machine and is used for the practical execution of tasks for the final examination, part 2 (AP2), for electronics technicians for automation technology. The module enables the complete execution of an automation task, from electrical wiring to PLC programming, commissioning, and troubleshooting. Technical equipment: Siemens S7 PLC control system Complete control cabinet with industrial wiring Voltage supply and protection technology Input/output circuitry Control of a conveyor system Motor drive with power unit Sensors and actuators Operating and signaling elements Terminal and documentation system Areas of application: Training for electronics technicians for automation technology AP2 examination preparation Vocational schools and technical training centers In-house training and further education Advantages: Industrial design based on special machine construction Not a simple training system, but a practice-oriented machine design Realistic simulation of an automation task Ready for immediate use Ideal for training apprentices Condition: Very good condition, year of manufacture 2022, fully functional. Scope of delivery: Complete testing/training module Control cabinet Conveyor system PLC control system Existing documentation

Condition: new, functionality: fully functional, power: 17.1 kW (23.25 HP), fuel type: diesel, color: orange, overall weight: 2,200 kg, operation weight: 2,200 kg, maximum load weight: 1,200 kg, tire condition: 100 %, shovel volume: 0.4 m³, digging bucket width: 140 mm, suspension: steel, Year of construction: 2026, Equipment: 4 in one shovel, all wheel drive, cabin, hydraulics, pallet forks, ☀️ Summer Price: Only €16,799! The TEC-POINT YX918 is a compact, robust, and versatile wheel loader for professional users who are looking for a machine that is ready for immediate use and has a strong range of features. Whether on the farm, construction site, in gardening and landscaping, in agriculture, in municipal operations, in the warehouse, or on commercial properties – the YX918 impresses with its compact dimensions, easy operation, solid technology, and a comprehensive range of accessories. Equipped with a proven Kubota V1505 diesel engine, a closed comfort cab, hydraulic joystick pilot control, quick coupler, 4-in-1 bucket, and pallet forks, this machine is ready for daily use right away. Your advantages at a glance ✅ Kubota V1505 diesel engine – proven, reliable technology ✅ Year of manufacture: 2026 ✅ New / unused ✅ 17.1 kW engine power ✅ Closed comfort cab with heating ✅ Adjustable comfort seat ✅ Hydraulic joystick pilot control for precise work ✅ Electric control handle ✅ Quick coupler for quick attachment changes ✅ 4-in-1 bucket included ✅ Pallet forks included ✅ Additional hydraulic function for attachments ✅ Boom lowering protection for increased safety ✅ Work lights ✅ 1,200 kg lifting capacity ✅ 0.4 m³ bucket volume ✅ 2,200 kg operating weight ✅ CE marking available ✅ 12 months warranty ✅ Spare parts and service directly from TEC-POINT ✅ Immediately available ✅ Europe-wide delivery possible The TEC-POINT YX918 is the right machine for: Agriculture and farm work Gardening and landscaping Construction sites and building yards Municipal operations Warehouses and commercial properties Tsdoyky E Hspfx Aqxoa Equestrian facilities Firewood production Pallet handling Material transport Private users with professional requirements Whether it's earth, gravel, sand, wood, feed, building materials, bulk goods, tools, or pallets – thanks to the combination of a 4-in-1 bucket, pallet forks, and quick coupler, the wheel loader can be used flexibly and is ready to work immediately. Technical data Manufacturer / Brand: TEC-POINT GmbH Model: YX918 Machine type: Wheel loader / compact loader / farm loader Condition: New / unused Year of manufacture: 2026 Engine: Kubota V1505 diesel engine Engine power: 17.1 kW Operating weight: 2,200 kg Payload / lifting capacity: 1,200 kg Bucket volume: 0.4 m³ Gradeability: 25% Minimum turning radius: 2,000 mm Maximum dump height: 2,300 mm Maximum dump reach: 700 mm Tire type: 20.5-16 Tire pressure: 350 kPa Cab: closed, with heating Control: hydraulic joystick pilot control Operation: electric control handle Steering: hydraulic Braking system: hydraulic Condition, service, and availability The machine is new, unused, factory-tested, and ready for immediate use. With us, you not only receive the wheel loader, but also the corresponding service: ✅ 12 months warranty ✅ Spare parts directly from our warehouse in Rheda-Wiedenbrück ✅ Personal service from TEC-POINT ✅ Inspection and testing possible by appointment ✅ Europe-wide delivery by freight forwarder possible Location 📍 Rheda-Wiedenbrück Come and visit us, test the TEC-POINT YX918, and see for yourself the features, ease of operation, and range of applications. Inquire now Secure your individual offer for the TEC-POINT YX918 wheel loader. The machine is immediately available and can be delivered throughout Europe on request.

Condition: new, functionality: fully functional, power: 4.8 kW (6.53 HP), fuel type: gasoline, overall weight: 550 kg, maximum load weight: 500 kg, lifting height: 1,020 mm, chain condition: 100 %, Year of construction: 2025, Equipment: hydraulics, rubber tracks, tilting carriage, Mini Track Dumper HT500Y-4 Compact professional dumper with lifting function – now with a special discount! The Mini Track Dumper HT500Y-4 is the ideal solution for construction, gardening and landscaping, agriculture, and work in confined spaces. Thanks to its rubber tracks, hydraulic tipper and powerful lifting function, the dumper is extremely off-road capable, stable and easy to operate. The machine impresses with its compact design, high load capacity and a reliable Briggs & Stratton gasoline engine. Take advantage of our current sales promotion now: Discount on all track dumper models – for a limited time only, while stocks last! The HT500Y-4 is ready for immediate use and offers a strong combination of performance, maneuverability and ease of operation. ⚙️ Technical data Engine & Drive Engine: Briggs & Stratton Engine type: 1-cylinder, OHV, 4-stroke, air-cooled Displacement: 203 cc Power: 6.5 hp at 3600 rpm Fuel: Gasoline Fuel tank capacity: 3.6 liters Performance & Capacity Maximum payload: 500 kg Weight: 550 kg Loading volume of the hopper: 200 dm³ Tilting angle: 100° Tilting system: hydraulic Dimensions Machine dimensions without pedal & hopper: 1570 × 880 × 1450 mm Machine dimensions with foot pedal & hopper: 2050 × 880 × 1450 mm Hopper dimensions: 1050 × 730 × 730 mm Track width: 700 mm Lifting & Height Maximum lifting height: 1020 mm Maximum tipping height: 970 mm Tipping distance: 220 mm Ground clearance: 110 mm Undercarriage Track width: 180 mm Contact area of tracks: 1000 mm Track gauge: 520 mm Turning radius: 1150 mm Speed: 2.88 km/h Climbing ability: 20° Rubber tracks for optimal ground grip ✅ Features & Benefits Todpoyqxw Isfx Aqxsa ✔ Removable protective container ✔ Easy control via operating lever ✔ Folding platform for flexible working ✔ Very compact – ideal for tight construction sites ✔ High stability thanks to track chassis ✔ Low-maintenance gasoline engine ✔ Hydraulic tipping function ✔ Powerful lifting function for comfortable unloading Areas of application Construction & renovation Gardening and landscaping Agriculture Stable & farm work Material transport on difficult terrain Work in confined spaces Condition & Delivery Immediately available New goods / unused, from current production Factory-tested, ready for immediate use Europe-wide delivery by freight forwarder possible 💶 SECURE PRICE ADVANTAGE Special price with discount: 3,100 € net plus VAT. Save now – a better price is possible! Benefit from our attractive offers. An inquiry is worthwhile! Location: Rheda-Wiedenbrück Inspection possible by appointment ➡️ Request now and secure 10% discount on track dumpers!