Used Folding Device for sale (15,206)

Condition: used, Year of construction: 2018, operating hours: 69,000,000 h, functionality: fully functional, Folder gluer machine Folding carton with longitudinal seam: Kodpfx Ajyg Edgsafenb max. 1,150 × 600 mm min. 75 × 55 mm min. 45 × 55 mm (with small carton device) Crash-lock bottom carton: max. 1,150 × 600 mm min. 146 × 80 mm 4-corner box (erected): max. 1,150 × 680 mm min. 120 × 110 mm 6-corner box (erected): max. 1,150 × 630 mm min. 250 × 130 mm With BELKHOFF control system Roller and drying tunnel TÜNKERS EAS 480 delivery station, right-hand, year of manufacture 2019

Condition: ready for operation (used), Year of construction: 1999, B&R Moll Marathon Folder Gluer / Pocket Folder - ‘Dial-a-Feed’ hopper-type friction feeder with belts - ‘Quadraplex’ glue control unit with 4 channels for up to 4 gluing heads, featuring electronic cut-off control Kjdpfx Aszgfzdsafonb - Tape dispenser - Infeed table with plough folding devices and guides - Valco pre-melt unit with 2 heated hoses and hot-melt gluing heads - Upper and lower buckle plate folding station with segmented rollers - ‘Dial-a-Stack’ compression stream delivery conveyor - Includes accessories and manuals.

Condition: excellent (used), functionality: fully functional, Year of construction: 2018, Duplex Inox KUGELMANN Spreader, 550-liter capacity, Type SDB105H063L120KHKAVA - Painted in RAL 2004 Holder Orange - Stainless steel design – container and sheet metal parts made of stainless steel, glass bead blasted and coated with a special paint. - Speed-dependent spreader - 2 augers and speed-dependent control - Stainless steel design – container and sheet metal parts made of stainless steel, glass bead blasted and coated with a special paint. - Color: Holder Orange Basic Duplex spreader: - Speed-dependent, twin-chamber mounted spreader with an extremely low center of gravity, two longitudinal augers with independent hydraulic drive as a conveying and metering device, the spreading disc is also hydraulically driven, the augers and spreading disc are separate and can be regulated independently in a closed-loop system (with feedback). - The application rate and spreading width are controlled via a microcomputer. - The set spreading rate is speed-dependent and controlled according to the vehicle speed. - For rapid emptying, transport, and assembly work, the discharge chute with spreader can be folded upwards. Standard equipment: - Microprocessor control unit MCSS (for operation) - Work lights can be switched on from the control panel - Rotating beacon can be switched on from the control panel - Partition between the spreading material chambers with equal division of the chamber volume (removable) - Rubber skirting attached to the discharge chute - Folding cover including operating cables - Winter service marking - Manual emergency operation of the hydraulic control valves (for operating the drives without control) - Prepared for wet salt system (retrofitting only possible at the factory) - Lighting system - Angled roof frame - Mounting frame and initial assembly of the spreader on the vehicle - Rotating beacon and work lights - Pre-carriage from the factory - Mounting kit Holder LIST PRICE: € 22,515 (plus applicable VAT) YOUR SPECIAL NET PRICE: € 15,400 (plus applicable VAT) The following option is available at an extra cost: Additional cost for outrigger legs, 3 tons: € 990 (plus applicable VAT) Ksdpfx Ajzf E Hqsafsnb Subject to changes, typographical errors, errors and prior sale. All information is provided without guarantee. The sale is made with the exclusion of any guarantee or warranty.

Condition: used, 2-station notching machine and folding machine EUROMAC type Multi 220/6R Press brake, press brake, notching machine Serial no. M11941298 Year of manufacture 1998 Cutting capacity 6 mm steel at 45 kg/mm2 4 mm for stainless steel Station I (notching) Notching angle 60° to 140° (with special blade from 30° to 140°) Knife length 220 mm Table size 950 x 640 - Manual angle adjustment via hand wheels - Notching angle with built-in blade set from 60° to 140 - Hydraulic clamping of the upper and lower knives - Automatic cutting gap adjustment - sheet hold-down device - Scaled measuring tapes embedded in the table - stop rails with angle adjustment - Operation via foot switch Station II (die bending device) Pressure force 18 ton Table size 950 x 340 Working height 1100 mm - stepless lifting speed Knodpomck Rysfx Aafsb - Infinitely adjustable stroke limiter - Stroke adjustment up to 30 mm working stroke - Reversible prism with 4x 90° prisms, length = 415 mm - 90° upper tool, length = 415 mm Motor power 4 kW Mains connection 400 Volt, 50 Hz Space requirement L x W x H 1150 x 1050 x 1460 mm Weight approx. 1000 kg good condition

Condition: like new (used), Year of construction: 2020, operating hours: 1,000 h, functionality: fully functional, total height: 1,600 mm, total width: 1,600 mm, total length: 15,000 mm, overall weight: 6,440 kg, The equipment has been used very little, is almost like new, and has under 1,000 operating hours. Three-corner packaging gluing machine with automatic box base forming and gluing device with cold adhesive. - Maximum format: opening 98 cm - Line speed: 0-300 m/min, continuously adjustable - Cardboard thickness: 280-700 gr/ sqm. - Box type: crash-lock base box, straight line box, double wall box. Knodpfowqcrqex Aafeb - Folding method: 1st fold at 180°, 3rd fold at 135°, 2nd & 4th folds at 180°, turntable for other models. Other specifications: - Equipped with sensors. - Operation via touchscreen displaying all important information about the machine status. - The belts are adjusted centrally by means of knobs. - The straps can be swung out of the way for easy access in the event of an intervention to unlock the boxes. - Separate, adjustable straps and stacking and removal. - Distance between products is adjustable by coupling. - Remote control panel with cable for easy format adjustment. - Special turning plate to make it possible to glue other types of boxes such as CDs. - Box type: crash-lock base box, straight box, double-walled box - Folding method: 1st fold at 180°, 3rd fold at 135°, 2nd & 4th folds at 180°, turntable for other models. - Feeding system: Automatic vibratory feed, - Grinding unit - Correction section - Pre-finishing section; - Motorization for format change - Electrical power: 11,5 kW - External dimensions: 15000 x 1600 x 1600 mm - Weight: 6440 kg

Condition: good (used), ZNHZ-508A Envelope Making Machine Paper weight 70 – 150 g/m² Production rate 3000 – 9000 pcs/h Knedpfsz A H Sgjx Aafob Maximum folded envelope size Western Style 324 x 229 mm Min. folded envelope size 100 x 100 mm Power 8 kW Weight 3000 kg Dimensions 6600 x 1200 x 1300 mm Year of manufacture 2014. Key advantages of the machine: – A bottom-mounted vacuum feeder allows for continuous material loading without stopping the machine. – A proprietary adjustable creasing and perforation system on the machine cylinder allows for loading material in the form of only the cut-out envelope outline. – Simple and easy adjustments simplify and shorten makeready time. – Standard bookbinding glue is applied from an inkwell through rotating rings with precise adjustment of its position and intensity. – Glue for the closure is also applied from an inkwell with precise adjustment of the intensity. – A vacuum suction system located on the cylinders allows for perfect folding of envelopes even at very high speeds. – The machine has two folding systems enabling double-closing of envelopes. – The electronic counting system is equipped with an electromagnetic separating device, allowing for separating envelopes, e.g., 50 pieces per envelope.

Condition: used, Year of construction: 2003, Single-sided edge trimming and gluing machine Manufacturer: IMA Type: AVM/K/I/G80/822/S3R3L20 Year of manufacture: 2003 For milling, edge gluing, and finishing for a standard groove - only for pre-shaped/pre-grooved doors and square-edged doors Left-hand machine (fixed stop on the left). Complete processing in 3 passes 1st pass: Processing of the top surface of the door (transverse processing) 2nd pass: Door long edge 3rd pass: Door long edge During the 2nd and 3rd passes, the protruding transverse edge from the 1st pass is milled off by using a co-rotating/counter-rotating milling process. Double groove gluing is only possible through modifications to the machine and subsequent manual finishing of the edge. Max. door thickness: - Straight edge: approx. 70 mm Knedpfx Ajzuykveafsb - Groove gluing: approx. 60 mm Stable machine frame as a support for aggregates and housing for electrical installation. Drive for feed speeds of approx. 5-25 m/min., mechanically infinitely adjustable. (not to be confused with processing speed) Continuous, plastic-coated strip-type conveyor chain, approx. 80 mm wide, with automatic central lubrication. Manually height-adjustable top pressure with a V-belt 80 mm wide and spring-loaded, ball-bearing guide rollers. Machine length approx. 10,900 mm Infeed table at the machine inlet. 1 horizontal, manually adjustable, unheated stop bar 1 joiner milling unit controllable, not swiveling, without sensing with 2 motors, each 3 kW Gluing unit for optional operation of straight edge or softforming gluing, by changing the glue application. Edge material: - Strips: up to 1.3 mm - Roll material: 0.4-3 mm - Solid wood strips: 6 mm Strip length max.: 2550 mm Strip height: 14-80 mm (depending on glue application) with: - Side adjustment by hand for the pneumatically controlled glue application. - Height adjustment by hand -15mm downwards and up to +10mm upwards. 1 bell for the main pressure roller, manually adjustable 1 glue application 0.8L, max. edge height 70mm, straight edge with pneumatic quick-release, Chem-Coat coated, electronic temperature control 1 hot melt glue application 0.8L with quick-release, up to max. 80 mm high edge material, soft edge, Chem-Coat coated, with temperature control and control unit for the strip coating 1 automatic Quickmelt hot melt glue feeder with a heating power of 5.0 kW 1 2-fold magazine only for edge material up to 3.0 mm thick, can be manually attached to the single-roll magazine 1 groove forming pressing unit for pressing the edge material into the groove with: - an activation unit 15 kW for re-activating the edge material for groove forming - a pneumatically controlled forming shoe for the underlapping edge - a pneumatically controlled forming shoe for the entire groove - additional post-pressing rollers for the edge areas in the groove - an electro-pneumatic lateral retraction device for the entire pressing unit 1 horizontal adjustment with mechanical digital display 1 trimming unit for 2 motors mounted on the top pressure for trimming the front and rear edge/strip overhang, for trimming cuts flush or with a bevel. 1 milling unit for 2 motors with height sensing, side sensing, for pre-milling from below and above with 2 motors 1kW, 400V, 200Hz, 12,000 RPM, 30° swiveling 1 milling unit for 2 motors with height sensing, side sensing, for fine milling from below and above with 2 motors 660W, 400V, 200Hz, 12,000 RPM, 30° swiveling Note: The technical data and descriptions are copies of the original order

Condition: good (used), For sale: professional hospital transport stretcher / medical trolley by Stryker – Prime Series 1125 Zoom model. The device is used in hospitals and emergency departments for patient transport. This model features the Zoom Drive system, which provides electric drive assistance and greatly facilitates patient movement. Manufactured by Stryker Medical USA – one of the world’s leading producers of medical equipment. Ksdpfx Aeyuqt Nsafsnb The stretcher comes with an adjustable backrest, foldable side rails, and integrated braking and steering systems. ⸻ Technical specifications: • Manufacturer: Stryker Medical • Model: 1125 Prime Series Zoom • Year of manufacture: 2014 • Drive: Zoom Drive – electric assist • Maximum load capacity: 318 kg • Lying surface width: 66 cm • Adjustable backrest • Folding side rails • Central braking system • Transport castors for hospital use

Condition: used, Folding former, folding machine, form folding machine, profiling machine, profiling system, slat production, blind production -Length measuring device: used for slats/blinds production -Rotary encoder: Heidenhain ROD 426.003 - 1000 -Pneumatic components: Manufacturer Festo -Dimensions: 350/400/H1130 mm Knjdpegal A Djfx Aafsb -Weight: 80 kg

Condition: used, functionality: fully functional, Year of construction: 2023, operating hours: 3,358 h, machine/vehicle number: K22268, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: JORNS, working width: 6,410 mm, folding beam adjustment: 200 mm, sheet thickness (max.): 2 mm, sheet thickness steel (max.): 2 mm, sheet thickness aluminum (max.): 2 mm, back gauge adjustment: CNC-controlled, back gauge: 1,250 mm, back gauge speed R-axis: 283 mm/s, back gauge travel distance R-axis: 1,250 mm, back gauge travel distance Z-axis: 1,250 mm, overall weight: 13,000 kg, total length: 8,500 mm, total width: 3,354 mm, total height: 1,938 mm, input voltage: 400 V, input current: 80 A, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, emergency stop, foot remote control, We offer this used Jorns JDB-150G-DP-1250-JC100-6.4-dsp panel bending machine for sheet metal, manufactured in 2023. Year of manufacture: 2023 Kedpfx Aasz Dilljfjnb Model: JDB-150G-DP-1250-JC100-6.4-dsp Rated current: 80 A Operating voltage: 3 × 400 V Frequency: 50 Hz Control voltage: 24 VDC Maximum hydraulic pressure: 210 bar Maximum pneumatic pressure: bar If you have any questions or need further information, please do not hesitate to send us a message or call us.

Condition: good (used), You are bidding on: a branded machine set – a folding machine from a renowned and well-known manufacturer – Schechtl HA and a guillotine shear RAS by Reinhard Maschinenbau Sindelfingen. Machine details: Folding machine: - Die rail bends cleanly – test possible on site Knodpjyqytqsfx Aafsb - Angle display - Bending length slightly over 2.5m - Sheet metal capacity: 1.5 mm for steel – also suitable for aluminium, zinc, etc. - Standard die rail - Foot-operated closure - Current new price approx. €20,000 net Guillotine shear RAS: - Electrically operated guillotine shear up to 2mm steel – also suitable for aluminium, etc. - Cutting length: 2.5m - Extension table for special applications included in the price – can be mounted on the left side - Optional spare blades available - Adjustable depth gauge from the front - Many additional onsite tools and auxiliaries available as options - Machines can also be purchased individually Important: Optionally, you will also find a wide range of machines and equipment for sheet metal and steel processing on offer in our shop, including various rails, depth gauges – everything relating to bending and shearing, such as press brakes, guillotine shears, drilling machines, slip rolls, slitting and profiling machines, accessories (beading devices, round rollers for gutter fabrication, back gauges, etc.), as well as hand tools and spare parts from many top manufacturers in stock. Please feel free to contact me for any questions. You will receive an invoice in accordance with § 25a UstG, VAT is included in the invoice amount (margin taxation system). Free loading available – approx. weight: bending machine about 1900 kg, shear about 1600 kg. Inspection and testing are possible and encouraged by prior phone appointment. Payment in cash upon collection. Benefit from our experience and expertise – we are happy to advise you. Collection by the buyer (or a shipping company commissioned by the buyer) should take place within 10 days after the end of the auction. Location: 97249 Eisingen, approx. 3 minutes from the A3 and A81 motorways. Article number: Folding machine RAS 251009

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, operating hours: 15,396 h, pressing force: 173 t, stroke length: 500 mm, overall weight: 16,000 kg, working length: 4,250 mm, Equipment: CE marking, full service history, No minimum price – guaranteed sale to the highest bidder! TRUMPF TruBend 5170 including BendMaster! The machine has been continuously serviced and maintained by Trumpf, with a complete service record. The cylinders are leak-proof and have no oil loss. The tools shown for the robot are included. TECHNICAL DETAILS Stroke: 500 mm Press force: 1,700 kN Working length: 4,250 mm Tool clamping: Hydraulic, top and bottom Number of axes: 6 Load capacity: 60 kg MACHINE DETAILS Voltage: 3 x 400 V Rated current: 41.0 A Frequency: 50 Hz Connected power: 28.0 kVA Control voltage: 24 V DC Follow-up time: max. 90 ms Follow-up distance at 220 mm/s: max. 10 mm Follow-up distance at 160 mm/s: max. 8.5 mm Operating pressure: max. 300 bar Weight: 16,000 kg Operating hours Press beam running time: 15,396 h Hydraulic system running time: 83,212 h Machine operating hours: 152,638 h Knedpjzzkvcofx Aafeb EQUIPMENT CE marking Documentation/Manual Rear stop with sensors CNC crowning Bendmaster (robot with 8 m travel) Vacuum manipulators CNC gripping station Double sheet detection BendGuard laser safety device Spare parts: Cable carrier, spare vacuum plate, BWF fixators (machine feet) The height and weight of the asset must be taken into account when selecting the transport vehicle. A forklift is available for loading. If collection is not completed within the specified timeframe, a storage fee of €20.00 per lot and for each day started will be charged. The fee must be paid before collection. The sale is made with the exclusion of any warranty or guarantee. The information on the technical data comes from the original offer. No guarantee is given for typographical or measurement errors. In case of doubt, please compare the information with the provided photos or inspect the goods on-site before the end of the auction.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1985, machine/vehicle number: 8444-08, workpiece length (max.): 6,000 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Maximum edge length: 6,000 mm Maximum material thickness: 1.25 mm Mechanical cutting device Hydraulic unit Flow rate of gear pump: 14.5 l/min Operating pressure: 140 bar Maximum pressure: 210 bar Electric motor power: 3 kW Motor speed: 1,450 rpm Voltage: 380 V Frequency: 50 Hz Oil tank capacity: 30 l Pressure gauge diameter: 63 mm Pressure gauge display range: 0–250 bar Pressure switch: 90 bar Hydraulic components Gear pump CPL 9 DQ Intermediate flange L25-2/004 Elastic coupling G 228/2P Return filter Fill and vent filter Oil level indicator Drain plug Glycerine pressure gauge Valve block with pressure, flow control, braking, and solenoid valves Hydraulic cylinders Number of hydraulic cylinders: 8 Type: GHZ-50 × 225-S spec. Piston rod with external thread M20 Length: 20 mm Swivel bearing at the rear Hydraulic motors Number of hydraulic motors: 4 Type: OMP 50 MACHINE DETAILS Control system Electrical machine control with operator panel (OP) Adjustable dwell times, angle ranges, and shutdown delays Variant control for different machine functions EPROM-based control Electrical supply Mains voltage: 380 V Frequency: 50 Hz Kedpfx Ajzy Ndcjafjnb EQUIPMENT Hydraulic unit OP-14 SM 8 hydraulic cylinders GHZ-50 × 225-S spec. 4 hydraulic motors OMP 50 Gear pump CPL 9 DQ Valve block with hydraulic valves Return filter Fill and vent filter Oil level indicator Glycerine pressure gauge Pressure switch Electrical OP control Hydraulic and electrical circuit diagrams

Condition: like new (used), Year of construction: 2023, functionality: fully functional, total height: 5,300 mm, ram adjustment: 150 mm, installation height: 570 mm, total width: 3,300 mm, total length: 5,250 mm, pressing force: 250 t, type of input current: three-phase, stroke length: 35 mm, input voltage: 400 V, distance between side stands: 820 mm, overall weight: 58,000 kg, control voltage: 24 V, input frequency: 50 Hz, HR 250/2200 SL – Punching Line (Demonstration and Trial System) Press frame + ram in cast design with optimal damping properties Turnkey complete system for: • Production of electrical sheet metal parts • Flat stamped parts • Flat progressive die-cut parts EQUIPMENT + ACCESSORIES: • Punching machine HR 250/2200 SL [ZEULENRODA] 2,500 kN | Stroke rate 80…250 min-¹ >also available without accessories/peripherals upon request< • Roller feed “push-pull”, [ZEHNDER & SOMMER] • RAZIOL roller strip lubricator • Strip thickness measuring device • Punching package control [UNIDOR / TRsystems] • Unwinding reel 3.0t [KOHLER] • 21-roll fine leveling machine, deburring attachment [KOHLER] • Motorized tool changing system with hydraulic lifting bars + insertion clamp • Scrap and parts removal • Servo punching shear • Control cabinet platform • Operator platform • Soundproof cabin • Safety fence TECHNICAL DESIGN: Stroke rate of the press: 80 - 250 min-¹ Ram stroke: 35 mm Quick lift: 75 mm Installed height: 570 mm at max. stroke (fixed 35 mm) at the bottom, ram adjustment (150 mm) at the top Table surface: 2300 x 1100 mm Clamping plate: 2300 x 1100 mm T-slots DIN 650: 22 mm Table opening: 2020 x 400 mm Ram surface: 2240 x 900 mm Ram stroke, fixed: 35 mm Quick lift: 75 mm Height above floor: 1380 mm (including clamping plate 200 mm) Strip inlet height: 200 - 400 mm (above the clamping plate) Stand opening, side: 820 x 500 mm (W x H) Recommended max. upper tool weight: 2200 kg Recommended upper tool weight: 1950 kg - Control system SIEMENS S7-1500 - 15’’ touch panel + two-hand control panel Knjdpfjzu Ryhsx Aafeb - Remote maintenance DESCRIPTION: - Press frame in gray cast iron design - Press ram in cast design - Direct drive with electro-pneumatic clutch-brake combination - Fully eccentric two-point eccentric shaft, forged - Power transmission via two connecting rod joints - Roller guide, 8-fold for precise ram guidance - Rotating mass balancer - Ram weight compensation by means of pneumatic bellows cylinder - Quick Lift 75 mm (quick lift function for fast tool access) - Condition monitoring (forces, temperatures, lubrication, pneumatics)

Condition: like new (used), Folding machine Sofrapli 505 ABN The machine is in very good technical and visual condition. The device has 2 pockets, pneumatic feeding, counter with the function of packing, total counting and folding speed indicator. Included with the machine are deflectors and brand new creasing rollers. 230V power supply. Ritschle compressor Extended electric delivery. Non-stop feeding with vacuum roller from below. A2 + format Kedpfxjwyakvj Aafjnb The weight of the processed paper – 40 – 240gsm Productivity, A4 / hour – up to 30,000

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, pressing force: 40 t, BAYKAL CNC press brake Mod.: APHS-C 125040 Unused SN: 28542 YEAR OF MANUFACTURE: 09/2021 in the following version: - DELEM control system DA-58T 2D-graphics with touch screen - CNC controlled backgauge with ball screws, X-axis 750 mm + 250 mm, R-axis = 130 mm - Manual table crowning - AKAS laser safety device - Safety cover on the side and rear - 2 pcs. Front support arms on linear guides - Top system tool holder - System tool holder at the bottom - Technical documentation - CE version - Colors: * RAL 7015 - slate gray * RAL 7035 - Light gray * RAL 3003 - Ruby red Technical data: - Pressing pressure: 40 t - Working length: 1,250 mm - Motor connected load: 4 kW - Oil tank volume: 80 lt. - Departure speed: 160 mm/sec. - Working speed: 10 mm/sec. - Retraction speed: 130 mm/sec. - Folding length: 1,250 mm - Stand passage: 1,070 mm - Stand depth: 1,470 mm - Table height: 800 mm - Machine height: 2,250 mm - Installation height: 455 mm - Stroke: 215 mm - Table width: 60 mm - Projection: 410 mm Ksdpfetz Azdsx Aafsnb - Weight: 3,300 kg Subject to errors and prior sale!

Condition: good (used), You are bidding here on a branded guillotine shear and a folding machine from the well-known German manufacturer Schechtl. Device features: - Guillotine Shear MSB 200: - Cuts 3 mm steel – significantly more for aluminum - Cutting length: slightly over 2 m - Front support table - 500 mm back gauge - Optional sheet metal tray - Free loading available - Folding Machine Schechtl MAX 200: - Rail bends cleanly – test possible - Degree indicator - Bending length: slightly over 2 m - Sheet thickness: 2.5 mm (steel, sheet metal, aluminum, zinc, etc., higher for softer materials) - Standard rail – special radius rails for aluminum and zinc available upon request (add-on and special rails) - Foot pedal operation - Optional back gauge We also have available: Schechtl MSB 200, Schechtl MA 200, Schechtl HA 200 (2 mm), segmented RAS 2 m / 2 mm, and many others from 1 to 6 m. Knodpfx Aoyviwqjafeb You will receive an invoice with VAT shown separately. Shipping can be arranged upon request. Free loading as shown in the pictures. Inspection and testing possible by prior phone appointment. Payment in cash upon collection – if you need anything else, please give me a call. Thank you! Collection should take place within 8 days after the end of the auction. Location: 97249 Eisingen (3 minutes from the motorway) Item numbers: 251007 and 251008

Condition: good (used), You are bidding here on a branded guillotine shear and folding bench from a very reputable and well-known manufacturer – Schechtl. Device specifications: Guillotine Shear HT 200 - Capacity: 1.25mm steel, aluminum, etc. and more - Cutting length: just over 2m - Depth stop - Front support, extendable Folding Bench - KS model – Capacity: 1mm steel, aluminum and more (up to 1.5mm) - Bending length: just over 2m - Foot-operated closer - Optional depth stop or beading attachment - Round rollers and additional guide rails included - Sale according to §25a UStG Optionally, I offer the possibility to purchase a segment bending bench from the top manufacturer Cidan – likely the market leader. Cidan Machinery also includes Thalmann (top manufacturer of long folding machines) and Forstner (leading slitting line manufacturer). This is the heavy-duty version – 1m / 2mm steel - Aluminum and more significantly higher capacity - Triple-segmented - Angle display - Foot-operated closer - Storage box Note: The segment bending bench can be purchased in addition to any of my machine sets, but will not be sold separately. Additional price available upon request. Kodeyw Si Ejpfx Aafonb The machines are in good and clean condition and ready for immediate use. They come from private ownership. Important: Optionally, you can find and purchase many machines and accessories for sheet metal and steel processing – such as folding benches, guillotine shears, drill presses, roll bending machines, slitting and profiling machines, accessories (beading device, round rollers for gutter production, back gauge, etc.), as well as additional hand tools and spare parts from leading top manufacturers in our shop. If you have any questions, I am always available to help. You will receive an invoice according to §25a UStG. The invoiced amount includes VAT (differential taxation applies). Free loading available – weight approx. 750 kg and 650 kg. Inspection and testing by appointment via phone is possible and encouraged. Payment in cash upon collection. Take advantage of our experience and expertise – we are happy to advise you. Collection by the buyer (or by a transport company commissioned by the buyer) should occur within 10 days after the auction ends. Location: 97249 Eisingen, approximately 3 minutes from motorway A3 and A81. Item number: Folding Bench KS and HT

Condition: used, functionality: fully functional, With this listing, you are purchasing a used “Estefold 2300 Offline Folding Machine” production system. Item for sale: 1 x Estefold 2300 Offline Folding Machine Condition: This listing is for a used device, which may show signs of wear (minor scratches or discoloration). The device has been tested for functionality. A test printout can be seen in the photo. Packaging and Shipping: You are welcome to view the device during our business hours. Please schedule an appointment! Sea-worthy packaging and worldwide shipping are available upon request! Before shipping or pickup, we’ll record a video of a functional test for you. Kjdezgt E Djpfx Aafenb For more information, please feel free to contact us directly.

Condition: good (used), DREISTERN P3.100.40/3 Profiling Line – 44 driven stations with flying shear Short title for platforms with character limitations: DREISTERN P3.100 Profiling Line, 44 Stations + Shear Platform Data * Machine Type: Profiling Line / Roll Forming Line * Manufacturer: DREISTERN-WERK * Model: P3.100.40/3 * Year of Manufacture: 2002 * Factory Number: 02 098 * Order Number: 38933-46 * Condition: Used, disassembled * Control System: Not available For sale is a comprehensively equipped DREISTERN profiling line, type P3.100.40/3, with 48 stations, 44 of which are driven, as well as an inline shear (“flying shear”). The line features quick-change plates, mechanical quick clamps, and a coolant piping system. Due to the large number of profiling stations, it is particularly suitable as a mechanical base for demanding, customer-specific roll forming applications. An expansion with additional stations is structurally possible. According to the previous operator, the line operated flawlessly until it was disassembled at the customer's plant. The control system is not available and is not included in the scope of supply. Recommissioning or control system adaptation by the buyer is therefore necessary. Machine Bed and Drive * Production direction: from right to left * Center distance: 330 mm * 48 stations total * 44 stations driven, with 44 gearboxes * Quick-change plates * Mechanical quick clamps * Coolant piping system * 1 × Baumüller DC motor, 42 kW * 1 × Baumüller DC motor, 15 kW Profiling Frames * Number included in scope of supply: 44 pieces * Tool width per frame: 275 mm * Working shaft diameter: 50 mm * Working shaft connection: 30 mm with keyway * Lower shaft mostly fixed; 6 frames with adjustable lower shaft * Axial adjustment * Adjustment range lower to upper shaft: 80–170 mm Gearboxes * Worm gear ratio: 1:21 * Lower/upper shaft ratio: 1:1 Inline Shear * Travel path: 1,900 mm * Profile rail guidance * Ball screw drive * Bosch servo motor * Valve block with punching unit * Folding table length: 3,000 mm * Emergency stop Scope of Supply * Machine bed with gearbox support * Infeed table * Pneumatic measuring wheel unit * Straightening device * Belt filter unit, 800 liters Knjdpfx Aaezzyd Aofjb * Hydraulic unit for the shear * 44 gearboxes * 44 profiling frames * 2 Baumüller DC motors * 66 universal joints * Inline shear according to the above description

Condition: used, Year of construction: 2005, functionality: fully functional, overall weight: 7,000 kg, Fanuc 21-T cnc control 3-jaw chuck 12-fold revolver (VDI40) C-axis driven tools Ksdpfxoz Ainye Aafsnb tail stock coolant device chip conveyor Technische Daten: / technical details Umlaufdurchmesser über Bett / rotary diameter over bed 420 mm Umlaufdurchmesser über Schlitten / rotary diameter over sledge 280 mm Drehlänge / turning length 600 mm max. Drehzahl Spindel / max. spindle speed 44-4000 UpM /rpm Eilgang X/Z / rapid feed X/Z 24/30 m/min Anzahl der Revolverplätze / number of tool places 12 Antriebsleistung Spindel / drive capacity spindle 18,5/22 kW Gewicht ca. / weight ca. 7000 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: ready for operation (used), Year of construction: 1951, Large working width: 1250 mm Knedev D E R Djpfx Aafeb for sheets up to: 1.75 mm opening width of upper beam: 70 mm adjustability of bending beam: 50 mm space required: 1880 x 740 x 1140 mm

Condition: used, Year of construction: 2007, functionality: fully functional, travel distance X-axis: 250 mm, travel distance Z-axis: 620 mm, Fanuc cnc control 3-jaw chuck 12-fold revolver (VDI40) tail stock coolant device chip conveyor Technische Daten: / technical details Umlaufdurchmesser über Bett / rotary diameter over bed 420 mm Umlaufdurchmesser über Schlitten / rotary diameter over sledge 280 mm Drehlänge / turning length 600 mm Verfahrweg X-Achse / travel X-axis 250 mm Verfahrweg Z-Achse / travel Z-axis 620 mm max. Drehzahl Spindel / max. spindle speed 44-4000 UpM /rpm Eilgang X/Z / rapid feed X/Z 30/30 m/min Anzahl der Revolverplätze / number of tool places 12 Antriebsleistung Spindel / drive capacity spindle 18,5/22 kW Gewicht ca. / weight ca. 7000 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Ksdpjz Arupsfx Aafenb Technical data, accessories and description of the machine are not binding.

Condition: good (used), Year of construction: 1989, sheet width 2050 mm plate thickness 8.0 mm pre-bending capacity 6.0 mm upper roll diameter 190 mm lower roll diameter 180 mm bending speed 5.2 m/min work height max. ca. 980 mm total power requirement 5.5 kW weight of the machine ca. 3500 kg. range L-W-H 2900 x 1200 x 1280 mm Furnishing: - Robust electro-hydraulic 3-roller bending machine - planetary movement of the bending rollers with reduced center distance - Hydraulic motors combined with planetary gears * for driving the 3 rollers - mobile operating unit, with connection cable + plug - extended roll ends for profile bending rolls - with conical bending device * Inclination of the side rollers by handwheels Kjdpfsz Dkzhsx Aafjnb * Workpiece limitation for a cone with a 45° pitch: * Working length max: 60% * Bending capacity max: 50% - free-moving operation * electric delivery rollers * electric turning/rolling movement * digital position display of the reels - hardened rollers SAE 1050 CK 45 - Hydraulic folding store for removing closed pipes - safety device (cable) - Original instruction manual + CE declaration * Machine link : ?machineno=1008-9401255

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, workpiece length (max.): 3,048 mm, workpiece width (max.): 1,524 mm, sheet thickness (max.): 3 mm, table load: 5,000 kg, No minimum price – guaranteed sale to the highest bidder! The machine’s control system and software have been renewed! TECHNICAL DETAILS Sheet thickness for circuit boards with a tensile strength of 400 N/mm² max.: 3.5 mm Sheet thickness min.: 0.5 mm Punch head force max.: 4 presses with max. force of 7 t & 4 presses with max. force of 26 t Force of the lower cylinder max.: 6 t Double-punch punching force: 12 t (2 hydraulic punches) Length of the input sheet min.: 370 mm Length of the input sheet max.: 3,048 mm Width of the input sheet min.: 300 mm Width of the input sheet max.: 1,524 mm Diagonal of the input sheet max.: 3,408 mm Length of the output sheet min.: 250 mm Length of the output sheet max.: 3,048 mm Width of the output sheet min.: 60 mm Width of the output sheet max.: 1,524 mm Kodpfjzzkt Uex Aafenb Vertical travel of the scissor lift table: 550 mm Usable load capacity of the scissor lift table: 5,000 kg Dimensions of the transportable stack of sheets min.: 300 x 100 mm MACHINE DETAILS Electrical data Voltage: 380 V Frequency: 50 Hz Current: 119 A Rated power: 61 kW Cooling capacity of the unit: 32.2 kW EQUIPMENT Scissor lift table TC27155C Motorized roller bed PRL3814F Universal destacking device DUF15 Punch head H2 Oil-dynamic hydraulic unit C1515 (3-part pump unit) Lower cylinder EI09 Double rotating punch P2R36 Water-air cooling unit R121 Refrigerant R407C Software RIO Control and management system MMACHNT-MICROMach Processor PENTIUM INTEL II 400 Mhz WINDOWS NT Documentation The height and weight of the asset must be taken into account when selecting the transport vehicle. A forklift is available for loading. If the item is not collected on time, a storage fee of €20.00 per lot and for each day or part thereof will be charged. The fee must be paid before collection. The sale is made with the exclusion of any guarantee or warranty. The information on the technical data comes from the original offer. No liability is accepted for typing or measurement errors. In case of doubt, please compare the information with the provided photos or inspect the goods on site before the end of the auction.