Used Genome Sequencer for sale (329)

Condition: used, Illumina DNA Sequencer MiSeq SY-410-1003 Description: RFID tracking for consumables MiSeq Control Software 2.6 LTSC Operating environment Temperature: 22°C ± 3°C Humidity: Non-condensing 20%–80% Altitude: Less than 2,000 m (6,500 ft) Air quality: Pollution degree II Ventilation: Maximum 1,364 BTU/h For indoor use only Light Emitting Diode (LED): 520 nm, 660 nm Dimensions W × D × H: 68.6 cm × 56.5 cm × 52.3 cm (27.0 in × 22.2 in × 20.6 in) Weight: 57.2 kg (126 lb) Power supply 90–264 VAC at 50/60 Hz, 10 A, 400 W Radio Frequency Identification (RFID) Frequency: 13.56 MHz Power: 100 mW Product safety and compliance NRTL certified IEC 61010-1 CE marked FCC/IC approved Hedpfx Aaexqnvrsqsw Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of delivery: (see pictures) Weight: approx. 35 kg (Specifications subject to change and errors excepted!) Further questions can be answered by phone.

Condition: good (used), Year of construction: 2002, Clampable cutter head type (max.) 460 mm Cutter head weight (max.) 150 kg Mounting disc diameter for cutter heads (Ø) 360 mm Mounting cone for cutter heads Nominal diameter Ø 58,227 mm travel -z axis 200 mm diagram-drawing enlargement ±10 - ± 500 µm weight of the machine ca. 2,3 t dimensions of the machine ca. 2 x 1,5 x 2,03 m In the manufacturing process for spiral-toothed bevel gears, the quality of the gear cutting gear cutting tools used plays a decisive role. Particularly in high gear cutting quality and a long service life can only be achieved with precisely can only be achieved with precisely adjusted cutterheads. Hjdpfx Aajw N S E Aoqow The Oerlikon cutterhead setting and testing device CS 200 enables quick and easy setting of the individual knives and simple adjustment of the individual knives, it checks the position and documents the measurement results. The measuring sequence on the CNC-controlled testing device is partially automated: The individual actions for carrying out the actions for carrying out the sequence are displayed on the screen via the operator guidance. The positioning of the individual knives in the cutter head and the height of the knife tips is largely automatic thanks to a special sequence and is simultaneously documented by means of a run-out diagram. A subsequent measuring sequence checks the radial position of the inner and outer cutting edges of all knives in the cutterhead. If individual test parameters on the knives do not correspond to the the tolerance specifications, this can be individually repositioned. The combination of semi-automated setting sequence, operator-guided set-up actions and automatic operator-guided set-up actions and automatic measuring sequence, cutterheads can be can be set conveniently, quickly and with high precision. Operator-guided setting and test sequence - Graphic display of the cutter head design and the measurement results with tolerance check - Instructions for the operator in plain text Instructions for the operator in plain text (without coded information) - Simple assignment of the measurement results to the knives - Documentation of the setting and measurement results via printer- Setting and test sequence suitable for ARCON®, RSR, Spirapid, SPIRON®, TRI-AC® types - Interface for neutral data

Year of construction: 2014, condition: excellent (used), Automatic Postbox traying system for envelope inserting systems. This SIMA 220 was connected to a Buhrs BB700 inserting systems, therefore it is blue. Installed in 2015 and just in use for 16 months! More pictures available on request! Description: Adjustable in height 600 mm up to 900 mm. Gathering section – with buffer for post boxen Automatic fillingstation for postboxes Automatic change of postboxes. Max 10 Postboxen can be in feeder Touchscreen – simple, and user-friendly user interface Complete with connection from envelope inserter - connection with all inserters possible! Format max.: 180mm x 285mm Format min.: 90mm x 145mm Speed: up to 20.000 envelopes per hour Envelope thickness max.: 8 mm Postbox change-over time: ca. 1,8 sec (max 2000 boxes per hour) Post boxes: Deutsche Post, Postcon, Schweizer Post, Oesterreichische Post, Belgische Post, Hollaendische Post, USPS Trays, Pin Boxen. Electrical connection: 16A, 400/230V, 4kW Pressure air: 6bar, 200l/min Connection: To all inserting systems possible The sima Automatic Mail Delivery lines up with any inserter and automates the presorting and letter tray preparation processes. The delivery checks for open flaps, non-readable addresses, and IMB Barcodes then automatically rejects any letter that should not be delivered. Various reading systems are available for the sima, from simple print mark readers up to a server based OCR/IMB reading system connected to the Digital Front End. Our patented collection unit safely stacks the envelopes individually- without contacting each othermaking twisting or interleaving almost impossible. The envelope stack is quickly pressed before filling the letter trays in accordance with USPS regulations (DMM). The exchange of letter trays occurs automatically with an exchange speed of up to 1,800 boxes/h (2.0 sec). The tray exchange unit can handle MM and EMM letter trays. A unique feature is its ability to intermix one and two foot letter trays depending to the presorting need. As an option, a postcode label printer can be integrated into the sima, which applies a tray label to the letter tray. Hedod Etagepfx Aaqsw The filled letter trays are temporarily stored on a large buffer section. The Sequence Repair System (SRS), which marks or separates mails that do not belong to the actual mail sequence, comes standard on this machine. The sima can instruct the operator what to do with the marked or separated mail. This SRS enables a constant production speed even when sequence problems ap

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, Single-sided laser and PU edge banding machine including workpiece return system Ligmatech Manufacturer: Homag Edge banding machine type: PROFI KAL 330/10/A6/L Return system type: ZHR05/L/115 Year of manufacture: 2013 - Laser activation unit Performance - PU65 application unit - Balti melting device - Feed rate 18-25 m/min - FK31/20-cycle Powertrim - FK31/F Feed rate: 15 – 25 m/min Workpiece thickness: 8 – 60 mm Minimum workpiece width: 60 mm Edge material (roll): 0.3 – 3 mm Edge material (strip): 0.4 – 20 mm Control: PC22 Control system: Powertouch Units and gluing Jointing cutter unit S2 Automatic horizontal adjustment for jointing cutter Automatic vertical adjustment for jointing cutter LaserTec activation unit Performance Basic gluing station A20, extension module Magazine extension for 6 rolls Freestanding horizontal roll plate Continuously adjustable edge pressure device Vacuum device for strip singulation Servo edge feed Edge thickness measurement for coiled material Quick-change system for application unit QA/PU PU65 application unit (interchangeable) Automatic glue dosage adjustment Balti melting device Automatic pressure zone adjustment Wetting system for pressure zone Release agent spraying unit top/bottom End trimming unit HL86 bevel/straight 0.22 kW servo Pneumatic adjustment for end trimming motor Automatic adjustment for end trimming stop Pre-milling unit BF20 Pneumatic adjustment for pre-milling unit Multi-milling unit MF21 servo Release agent spraying unit top Profile trimming unit FK31/20-cycle Powertrim Profile trimming unit FK31/F Multi-scraper MN21 servo with chip breaker Finishing unit FA11 top/bottom, consisting of Glue joint scraper Cleaning agent application top/bottom Buffing unit Pneumatic adjustment FA11 Additional equipment Edge banding of solid wood edges Automatic adjustment of infeed fence Infeed extension 500 mm Sliding carriage Scissor-type workpiece support Scissor extension Workpiece thickness 8 mm instead of 12 mm Potential-free contact Flexible edge sequence control software Set-up-in-the-gap Workpiece return system ZHR 05/L/115 Hjdjxgrfpopfx Aaqsw Manufacturer: Ligmatech Year of manufacture: 2013 Workpiece parameters Length: min. 300 – max. 2500 mm Width: min. 60 – max. 1100 mm Thickness: min. 8 – max. 60 mm Weight: max. 50 kg Feed rate: 8 – 30 m/min

Year of construction: 2025, condition: new, functionality: fully functional, Dishwasher Model: R-Line 1500 with base Quick-ready system Hodpfx Aofffhxsaqsw Euronorm 500 2.4 liters of fresh water consumption 7 washing programs with 3 easy Rinse aid and detergent dosing pump extra deep interior for sheets / tubs 600 x 400 mm DGUV V3 checked Sequence / drain pump Connection: 400 V, 7.7 kW, 16A-CEE plug Dimensions: 600 x 700 x 1128 mm, WxDxH with warranty Included accessories: 1 plate basket 1 universal basket 1 cutlery basket Inlet and outlet hoses

Condition: used, Krauss Maffei SE502 MC4 sequence controller- removed from KM 18 C3 Hedpfx Asrr Eh Aeaqjw - removed from running machine - fully functionalmanufacturer: Krauss Maffei type: SE502 spare part no.: 5 Dition: gebraucht

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 88113 € 1415.61 € 74900 € 220 to 3050 mm Y1 / Y2 / X Achse 265 mm 2600 mm Hsdpfxewiqudo Aaqsw 450 mm 530 mm hydraulisch 140 mm/s 10 mm/s 140 mm/s 500 mm/s 350 mm/s 250 mm 900 mm 104 mm 250 l 22 kW 4250 mm 1770 mm 3000 mm 12600 kg Special campaign until 23.12.2025 Special price and SKY 22 control free of charge Standard accessories: 3 axes (Y1, Y2,X) CNC control SKY 22 - intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5“ in full HD - with 2D and 3D working screen - direct programming of the bending angle - user friendly programming in dialogue form optionally in 2D or 3D mode - 2D and 3D simulation of the bending sequence - automatic tool selection in 3D mode - automatic calculation of the blank sheet size - bending order calculation - graphic product and tool memory - correction possibility - USB and Ethernet interfaces for import, backup and programm transportation - OS: Windows - IGES, STEP, DXF files import servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides CNC crowning table upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) laser safety device Fiessler AKASmounted on the upper beam linear guided sheet support arms according to CE rules oilfilling users manual in English or German ADVANTAGES OF AD-S COMPAIRED TO PDF: - more stroke, installation height and throat - higher approach and retraction speed of the top beam - higher backgauge speed - backgauge finger on double instead of single linear guide - more options available such as: additional backgauge axes (e.g. Z1/Z2, Delta X, up to 6 axes), bending aids, laser angle measuring system, tandem design, other CNC controls ... OPTIONAL EQUIPMENT: R-Axis R/Z1/Z2-Axis DBend, 3D CAD/CAM importing- and simulation program (step, iges and dxf file import) CNC Control Delem DA66 S CNC Control DELEM DA-69S 3D incl. PC software Profile-S with 3D file import option Hydraulic or pneumatic tool clamping for Euro or Wila tools

Condition: good (used), Year of construction: 2004, Clampable cutter head type (max.) 460 mm Cutter head weight (max.) 150 kg Mounting disc diameter for cutter heads (Ø) 360 mm Mounting cone for cutter heads Nominal diameter Ø 58,227 mm travel -z axis 200 mm diagram-drawing enlargement ±10 - ± 500 µm weight of the machine ca. 2,3 t dimensions of the machine ca. 2 x 1,5 x 2,03 m In the manufacturing process for spiral-toothed bevel gears, the quality of the gear cutting gear cutting tools used plays a decisive role. Particularly in high gear cutting quality and a long service life can only be achieved with precisely can only be achieved with precisely adjusted cutterheads. The Oerlikon cutterhead setting and testing device CS 200 enables quick and easy setting of the individual knives and simple adjustment of the individual knives, it checks the position and documents the measurement results. The measuring sequence on the CNC-controlled testing device is partially automated: The individual actions for carrying out the actions for carrying out the sequence are displayed on the screen via the operator guidance. The positioning of the individual knives in the cutter head and the height of the knife tips is largely automatic thanks to a special sequence and is simultaneously documented by means of a run-out diagram. A subsequent measuring sequence checks the radial position of the inner and outer cutting edges of all knives in the cutterhead. If individual test parameters on the knives do not correspond to the the tolerance specifications, this can be individually repositioned. The combination of semi-automated setting sequence, operator-guided set-up actions and automatic operator-guided set-up actions and automatic measuring sequence, cutterheads can be can be set conveniently, quickly and with high precision. Operator-guided setting and test sequence - Graphic display of the cutter head design and the measurement results with tolerance check - Instructions for the operator in plain text Instructions for the operator in plain text (without coded information) - Simple assignment of the measurement results to the knives - Documentation of the setting and measurement results via printer- Setting and test sequence suitable for ARCON®, RSR, Spirapid, SPIRON®, TRI-AC® types - Interface for neutral data Hodpoul Efmsfx Aaqsw

Year of construction: 2014, condition: excellent (used), Automatic Postbox traying system for envelope inserting systems. This SIMA 220 was connected to a Buhrs BB700 inserting systems, therefore it is blue. Installed in 2015 and just in use for 16 months! More pictures available on request! Description: Adjustable in height 600 mm up to 900 mm. Gathering section – with buffer for post boxen Automatic fillingstation for postboxes Automatic change of postboxes. Max 10 Postboxen can be in feeder Touchscreen – simple, and user-friendly user interface Hsdpfx Ajd Etadsaqew Complete with connection from envelope inserter - connection with all inserters possible! Format max.: 180mm x 285mm Format min.: 90mm x 145mm Speed: up to 20.000 envelopes per hour Envelope thickness max.: 8 mm Postbox change-over time: ca. 1,8 sec (max 2000 boxes per hour) Post boxes: Deutsche Post, Postcon, Schweizer Post, Oesterreichische Post, Belgische Post, Hollaendische Post, USPS Trays, Pin Boxen. Electrical connection: 16A, 400/230V, 4kW Pressure air: 6bar, 200l/min Connection: To all inserting systems possible The sima Automatic Mail Delivery lines up with any inserter and automates the presorting and letter tray preparation processes. The delivery checks for open flaps, non-readable addresses, and IMB Barcodes then automatically rejects any letter that should not be delivered. Various reading systems are available for the sima, from simple print mark readers up to a server based OCR/IMB reading system connected to the Digital Front End. Our patented collection unit safely stacks the envelopes individually- without contacting each othermaking twisting or interleaving almost impossible. The envelope stack is quickly pressed before filling the letter trays in accordance with USPS regulations (DMM). The exchange of letter trays occurs automatically with an exchange speed of up to 1,800 boxes/h (2.0 sec). The tray exchange unit can handle MM and EMM letter trays. A unique feature is its ability to intermix one and two foot letter trays depending to the presorting need. As an option, a postcode label printer can be integrated into the sima, which applies a tray label to the letter tray. The filled letter trays are temporarily stored on a large buffer section. The Sequence Repair System (SRS), which marks or separates mails that do not belong to the actual mail sequence, comes standard on this machine. The sima can instruct the operator what to do with the marked or separated mail. This SRS enables a constant production speed even when sequence problems ap

Condition: used, Year of construction: 2006, x-travel 1050 mm y-travel 510 mm z-travel 510 mm control Fusion 640 M Nexus spindle taper DIN 69871/SK40 Feed speed 8000 mm/min. turning speed range 35 - 12.000 U/min rapid travel x/y/z 36 m/min distance spindle /table max. 660 mm distance spindle /table min. 150 mm no. of tools in the magazine 30 Stück tool taper CAT 40 Tool diameter 80 mm wotkpiece diameter with 2 vacant positions max. 125 mm max. tool weight 8 kg max. tool length 350 mm table length 1300 mm table width 550 mm number of T-slots 3 T-slot - width 18 mm T-slot - distance 100 mm max. table load 1200 kg table height over floor 850 mm coolant tank 250 l coolant pump 4,5 bar internal coolant system feed 15 bar coolant capacity 271 l/min required air pressure 700 l/min spindle drive 18,5 connected load frequency 400 V connected load 36,6 kVA frequency 50 Hz Needed pneumatic pressure 5 (bei 200 l/min) bar weight of the machine ca. 6,9 t dimensions of the machine ca. 2,90 x 2,84 x 2,81 m Including special accessories: -Cooling through the spindle (15 bar) -Chip conveyor, hinged belt on the left side -Torque-dependent drilling cycle (Mazatrol) -Automatic determination of drilling depth increments after torque detection. (preferably in combination with HSS tool) -Interface set Contents: - Interface for keyboard - Interface for mouse - Interface for printer Retrofitting not possible Machine color gray / black -CNC Performance Option Package Package contents: - Shared variables (600 pairs) - MAZAK Tornado thread tapping (EIA/ISO) - Synchronous thread cutting - EIA/ISO input function - EIA/ISO special function Spiral interpolation (G02.1, G03.1), 3D tool correction (G40-G42) Scaling (G50, G51) etc. - EIA/ISO, Constant feed (G93) When using this function, the feed rate remains constant for straight and curved combinations on the contour. - EIA/ISO tool length measurement (G37) - EIA/ISO, programme unit stop function Programme sequence is automatically stopped at a specified programme unit. - MAZACC-2D (Mazatrol & EIA/ISO) Precision control function for precise vector interpolation and optimal acceleration and deceleration at edges and radii. Hjdpfjxp Rywjx Aaqsw This enables improved two-dimensional shape accuracy. - Additional workpiece coordinate system (G54.1 P1 - 48) 48 pairs - Spiral machining function (G33) for boring head machining (e.g. with d'Andrea tool) - Used machine without warranty - - All dimensions, weight and performance data are non-binding

Year of construction: 2025, condition: new, functionality: fully functional, Dishwasher Model: R-Line 1500 Quick-ready system Euronorm 500 Hjdjfffhwopfx Aaqsw 2.4 liters of fresh water consumption 7 washing programs with 3 easy Rinse aid and detergent dosing pump extra deep interior for sheets / tubs 600 x 400 mm DGUV V3 checked Sequence / drain pump Connection: 400 V, 6.7 kW, 16A-CEE plug Dimensions: 600 x 700 x 850 mm, WxDxH with warranty Included accessories: 1 plate basket 1 universal basket 1 cutlery basket Inlet and outlet hoses

Condition: used, Krauss Maffei SR 500 processor card for MC3F- for MC3F sequence control - removed from running machine - fully functionalmanufacturer: Krauss Maffei type: SR500/310 spare part number: 5 Hedporr Ehqsfx Aaqew Dition: gebraucht

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 100920 € 1907.39 € 220 to 4050 mm Y1 / Y2 / X Achse 265 mm 3600 mm 450 mm 530 mm hydraulisch 160 mm/s 10 mm/s 140 mm/s 500 mm/s 350 mm/s 250 mm 900 mm 104 mm 250 l 22 kW 5250 mm 1770 mm 3000 mm 14750 kg Standard accessories: 3 axes (Y1, Y2,X) CNC control DT-15 - 2D grafic display 15" - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of the bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility Hedpfx Aaowirwgsqew - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides CNC crowning table upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) laser safety device Fiessler AKASmounted on the upper beam linear guided sheet support arms according to CE rules oilfilling users manual in English or German ADVANTAGES OF AD-S COMPAIRED TO PBF: - more stroke, installation height and throat - higher approach and retraction speed of the top beam - higher backgauge speed - backgauge finger on double instead of single linear guide - more options available such as: additional backgauge axes (e.g. Z1/Z2, Delta X, up to 6 axes), bending aids, laser angle measuring system, tandem design, other CNC controls ... optional equipment: R-Axis R/Z1/Z2-Axis DBend, 3D CAD/CAM importing- and simulation program (step, iges and dxf file import) CNC Control SKY22 CNC Control Delem DA66 S CNC Control DELEM DA-69S 3D incl. PC software Profile-S with 3D file import option Quick Release Clamping

Condition: used, Year of construction: 2018, Edge banding machine AKV 3006 DK - F with jointing milling unit including DIA - tools Jointing thickness up to 40 mm Workpiece thickness up to 3 mm Combined milling station radius R 2.5 mm Technical description With application of hot glue to the workpiece for edge material up to 3 mm Workpiece thickness 60 mm without jointing unit, 40 mm with jointing unit Maintenance-free, coated glue pot HF - cross-cut station (16,000 rpm) for front and rear edge overhang HF - milling station (16,000 rpm) with interchangeable cutter (combination version) and fine adjustment from the operator side Free slots for additional processing units (system Hebrock), feed approx. 10 m/min Cutting depth adjustment of the cross-cut saw Signal lamp for workpiece sequence, robust chain drive, ergonomically arranged control panel Double-roller top pressure beam Aggregate viewing window from machine rear and operator side PLC control including touchscreen Technical data: - Feed speed 10 m/min - Panel thickness 8 - 40 mm - Weight: depending on equipment approx. 1550 kg - Dimensions (L x W x H) 5250 x 1445 x 1600 mm 2-point pneumatic cutter adjustment 1 unit Switching between radius - flush/bevel for the combined milling stations, switching between bevel or flush is manual by flipping the stop flap in the machine Buffing station (polishing) 1 unit Hsdpfjxfh Tmsx Aaqew Corner rounding cutter 1 unit incl. combination tool and pneumatic bevel/radius adjustment, max workpiece thickness 40 mm Minimum workpiece length 300 mm Radius R 2.0 mm Radius scraper 1 unit incl. pneumatic lift device, radius R 2.0 mm Surface scraper 1 unit with pneumatic engagement control Glue station change system incl. 2nd glue pot and glue outlet downwards 1 unit for quick color change Grooving saw unit horizontal into the edge 1 unit incl. pneumatic lift device and grooving tool Separate extraction of jointing unit 1 unit directly attached to jointing unit vertically upwards d=80mm for optimal suction performance from AKV 3005 DK-F urgently recommended Ball bearing for corner rounding cutter 24.1mm 1 unit Ball bearing for corner rounding cutter 24.2mm 1 unit Interchangeable motor 0.37 kW for corner rounding cutter 1 unit with quick-change device incl. radius cutter R 1 Interchangeable spindles 1 set = 2 pieces 1 unit 1 set of quick-change motors for longitudinal processing top and bottom incl. tool R 1 Compressed air requirement: 100 - 150 l/hour. Storage location: Nattheim

Condition: ready for operation (used), empty load weight: 1,350 kg, total length: 1,960 mm, total width: 1,170 mm, total height: 1,070 mm, additional equipment features: CNC full automatic, Full automatic circular saw Automatic CNC positioning of sawblade = automatic turntable, up to 180° left and right Hedpfxexpki Es Aaqjw Equipped with: 1 - workpiece storage unit (green) + auto rollerconveyor, length 7 meter 2 - auto feed-in by pulling workpiece to sawblade, max single movement of 2000 mm - repositioning is possible for longer lengths 3 - auto feed-out of cut workpiece, max movement of 1000 mm 4 - unloading table with chains Automatic zero point recognition Automatic programmed controlled processing of cutting sequences Storing of programs with different sawing tasks Dia saw / abrasive - disk: max 425 mm Turningspeeds: 6 > 30m/min Power needed / motorpower: 5,5 kW

Condition: new, Year of construction: 2017, functionality: fully functional, Item number: 470722 Serial number: 470722-5 Material: Aluminum Total weight: 27 kg Dimensions Base plate: 460mmx300mmx25mm Upper guide plate: 300mmx300mmx22mm Overall height: 105mm Travel: 130mm Total length: 680mm Hjdpfou Raqpox Aaqjw The Tünkers LE100-150 VRL SB T02-4 is a pneumatic linear unit designed for precise and repeatable linear movements in industrial applications. With a pneumatic drive, it is ideal for automated production processes in which exact positioning and stable sequences are required. The robust design ensures a long service life and low maintenance requirements, even under intensive use and demanding conditions. The unit can be flexibly installed both horizontally and vertically, which increases its adaptability to different areas of application. In addition, it is possible to integrate sensors and control components to monitor and control the movement even more precisely. This makes it a versatile and reliable solution for industrial applications where high precision and durability are required.

Condition: good (used), Year of construction: 2006, Ref:10979 . 2006 Heidelberg Stahl TH82/64K-RFH 16pp High performance all buckle folding machine with computerised auto set-up of fold plates & rollers. Comprising; • RFH82 continuous loading round pile feeder with air stream table designed for high run lengths • With low operator strain, double wheel suction head for wide format sheets. • Digital microprocessor control with touch screen display for automatic setting of fold plates and roller pressures with learning function for signature length, suction & spacing with run monitoring, integrated total and batch counter with memory. • Touch-screen for fully automatic setting of fold plates and roller pressures. • Combination buckle plates with swing-away deflectors for quick change from stop to fold. • Setting adjustments can be made outside the machine ‘on the fly’. • Sound hoods covering all buckle units. • SBP.D presser/stacker delivery unit. Including compressor, tools, spares & manuals. Accessories: Hodpfx Aaswxw Sneqew Electronic gate-fold plate with control unit (to be confirmed). VFZ mobile electronic ‘Z’ knife 32 page fold unit. Folding sequence: 1st buckle unit - 82cm with 4 plates, perforating/scoring shafts 2nd mobile buckle unit - 66cm with 4 plates, perforating/scoring shafts 3rd mobile buckle unit - 56cm with 4 plates, perforating/scoring shafts VFZ mobile electronic knife fold. Specification: Sheet size, Max: 82 x 128 cm (Continuous Feeder) Min: 14 x 18 cm Fold length, Min: 6 cm Mechanical speed : 50 - 230 m/min Folding production : Max. Buckle 50,000 s.p.h. Option of: 2010 Palamides Alpha 500 Plus Presser/Stacker

Condition: good (used), Year of construction: 2019, operating hours: 1,994 h, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 1,000 mm, controller manufacturer: Fanuc, controller model: Fanuc 31i-B, spindle speed (max.): 10,000 rpm, number of spindles: 1, mount diameter: 100 mm, Operating hours: 7194 / usage time: 1994 Year of construction: 2019 Control unit: Fanuc 31i-B Spindle: PC100i (10.000 1/min) Tool clamping system: HSK 100 Tool magazine / places (Options): Chain/50 Rotary table: 360.000° X 0,001° Hodpfjvvmnujx Aaqsw Coolant unit: KNOLL, KF 400, IKZ 70 bar Positioning range XYZ (mm): 1000 / 1000 / 1000 Pallet size (mm): 630 X 630 Workpiece clamping: Hydraulic 80 bar Additonal options, Specifics: HELLER facing slide unit; Receiver for measuring probe (RENISHAW); Coolant temperature control; forward looking collision avoidance; Interface for exhaust system; 3 colour status lamp; work area flush; Scraping conveyor for wet machining; Fast drill fracture sensing (SBBK); multi-spindle-head support (MSK); Thermal growth compensation; Feed force display; Automatic loading sequence; Automatic unloading sequence; increased tool weight 35kg; tool codechip; Since response emails from Maschinensucher often end up in the spam folder, we kindly ask you to regularly check this folder or contact us directly.

Condition: new, Year of construction: 2024, Martin T 45 thickness planer with XPLANE cutterblock The T45 thicknessing machine offers ideal conditions for modern production: It delivers cleanly planed surfaces, is quick and easy to operate and works extremely quietly. and works extremely quietly. The standard electronic control system makes Thanks to 99 storable planing dimensions, setting the planing height is so easy that even the the first workpiece fits perfectly. Of course, the thicknessing table can also be moved at the simple press of a button, or can be incremented by 0.1 mm. upwards. The switching elements of the feed control are also within easy reach. reach. The heavy, vibration-damping composite stand with the high-quality the high-quality bearing-mounted planing shaft guarantees excellent surfaces. Thanks to the sound-insulating construction, you can work quietly even in the standard version. - Planing width: 630 mm - Weight: approx. 1,200 - 1,400 kg - Planing height: 2.8 - 300 mm - Table length: 1,260 mm - Workpiece length min.: 270 mm - Speed: 5,000 rpm - Operation: 1-axis control for planing dimension, max. 99 values can be stored, 49 of which can be used for a freely programmable planing sequence; button for manual quick and fine adjustment of planing thickness according to digital display, push button for cutterblock start and stop, integrated operating hours counter - Cutterblock: Xplane solid steel cutterblock Cutterblock with 3 spiral rows of knives (33 cambered hard metal knives per row), delivery includes full set of knives and a Torx T20 T-wrench; shaft speed 6,000 rpm included; The emission sound pressure level LpA during processing is reduced by 10 dB(A) - Thicknessing table: Electric thicknessing table adjustment with fine adjustment, travel speed 10 mm/s, mounted on 4 support spindles to prevent tilting, table surface precision-planed - Feed: 2 speeds 6 / 12 m/min, can also be selected electrically during planing, large rubber feed rollers Ø 85 mm to compensate for different thicknesses of wood, rubber rollers are gentle on the material and self-cleaning, easy roller change; link pressure beam at the infeed - Suction system: Swivel-up, split hood with chip extraction nozzle Ø 160 mm, can be connected optionally on the left / right (in special cases on both sides); minimum extraction air volume: 27 m³/min. at 20 m/s - Maintenance device: Central lubrication strip for oil lubrication points; bearing / cutter shaft lubrication via nipple Hsdpfxsqlck Ns Aaqjw - Accessories: 1 grease gun, filled with long-life grease 1 oil gun 1 open-end wrench 1 tool for blade change 1 pair of blind knives 640 mm 2 pairs of TERSA reversible knives 640 mm CV - Emission values: Emission sound pressure level at the workplace LpA according to DIN EN ISO 11202 [dB(A)] Idle noise (without extraction) P1 65 Idle noise (w. extraction) P1 77 Operating noise (without extraction) P2 65 Operating noise (with extraction) P2 78 Sound power level LWA according to DIN EN ISO 3746 [dB(A)] Idle noise (without extraction) 84 Operating noise (with extraction) 90 Dust emission Low dust emission according to DGUV 209-044 / BGI 739-1 Location: ex stock 54634 Bitburg - immediately available -

Condition: used, Year of construction: 2009, HOLZ-HER edge banding machine CONTRIGA 1366 Edge thickness: 0.4-30 mm (depending on equipment) Edge height: 51/66 mm (depending on equipment) Panel thickness: 6-45/60 mm (depending on equipment) Edge types: Rolls and strips Feed speeds: Continuous feed from 12-30 m/min (depending on equipment) With adjustable infeed level in the magazine area (max. adjustment range 30 mm) With height-adjustable magazine plate for changing the lower edge overhang With large magazine plate Ø 820 mm for edge rolls up to Ø 800 mm With transport chain including automatic central lubrication With motor-driven, position-controlled bridge height adjustment With pneumatic locking roller for the shortest workpiece sequence With extendable workpiece support (extension width 1600 mm) With space-saving, pneumatically controlled sliding hoods over the entire machine (Deviations for individual units are possible) with motorized infeed guide with injection oiler for lubricating all joints and bolts (including operating hours counter) with central connection for extraction (2x Ø 200 mm) with integrated chip collection box at the end of the machine (when radius scraper unit is installed) PPC 231 control system - Power PC for efficient setup and changeover - 15" SVGA screen with touchscreen - 128 MB CF memory card - USB connector on board - Ethernet network connection - Keyboard connector on board - Windows-like user interface - all information in plain text and/or graphics - Rotatable and pivoting control panel at eye level - Dust-proof membrane keyboard with softkeys (pushbuttons) - LED display for unit preselection - Program list with program names and numbers - Extensive program memory - Individual selection of the units with the functions as basic setting options for setpoints, route points and tool corrections as well as the fixed route points - Centralized and clear setup processes for units and their axis settings via fine adjustment (depending on the equipment) - Interval display for the shortest workpiece distance - Integrated path control - Path points are controlled generally or program-specifically - Clear and complete recording of all operating data - Service messages in plain text - Diagnostic system - including integrated synchronous bus system for high precision in unit control - Individual administration for up to ten users, including password protection - Online maintenance (optional), data exchange with HOLZ-HER Service - Barcode interface (optional) BASIC MACHINE CONTRIGA 1366 - Belt bridge Options and accessories for the basic machine Spraying device 1856 for the inlet and outlet area For the inlet area: Electronically controlled release agent sprayer with Riepe-LPZ/II release agent For the outlet area: Electronically controlled cleaning agent sprayer with Riepe-LP163/93 cleaning agent (only in conjunction with pre-milling unit 1961 and surface scraper 1964) Joint milling unit Joint milling station 1803 (2x 2.6 kW, 200 Hz, 12000 min-1) With two plunge-controlled milling units 1 unit in up-cutting direction 1 unit in down-cutting direction Plunge path 5 mm With static frequency converter 200 Hz Without milling tool With ProLock screw-in clamp for fast tool changes Tool for 1803 (workpiece height up to 60 mm) Diamond milling cutter PRO UT 2 pieces (front and rear) including protective covers Ø 100-63 - Ø 30 mm, Z = 3 + 3 + 3, 1x left-hand rotation, 1x right-hand rotation Noise-reduced milling cutter with integrated chip guide DFC technology (Leitz syst Hjdpfx Aaovvkfdjqew

Condition: good (used), Year of construction: 2014, functionality: fully functional, overall weight: 2,200 kg, KUKA KRC4 linear axis 1500/3T Article number: 8143983 Serial number: 143983 Hsdpfsvzxg Tsx Aaqew The KUKA KRC4 linear axis is a high-precision and robust motion unit that is ideal for industrial applications. It ensures precise control of motion sequences and plays a central role in automation processes and robotic systems within production. Its stable construction ensures consistently reliable performance, even in the most demanding applications.

Condition: new, Year of construction: 2024, Martin T 45 thickness planer with Tersa cutterblock The T45 thicknessing machine offers ideal conditions for modern production: It delivers cleanly planed surfaces, is quick and easy to operate and works extremely quietly. and works extremely quietly. The standard electronic control system makes Thanks to 99 storable planing dimensions, setting the planing height is so easy that even the the first workpiece fits perfectly. Of course, the thicknessing table can also be moved at the simple press of a button, or can be incremented by 0.1 mm. upwards. The switching elements of the feed control are also within easy reach. reach. The heavy, vibration-damping composite stand with the high-quality the high-quality bearing-mounted planing shaft guarantees excellent surfaces. Thanks to the sound-insulating construction, you can work quietly even in the standard version. - Planing width: 630 mm - Weight: approx. 1,200 - 1,400 kg - Planing height: 2.8 - 300 mm - Table length: 1,260 mm - Workpiece length min.: 270 mm - Speed: 5,000 rpm - Operation: 1-axis control for planing dimension, max. 99 values can be stored, 49 of which can be used for a freely programmable planing sequence; button for manual quick and fine adjustment of planing thickness according to digital display, push button for cutterblock start and stop, integrated operating hours counter - Cutterblock: TERSA solid steel cutterblock Z4 Ø 125 mm; incl. blocking for easy cutter change Hsdpfsqlckpjx Aaqjw - Thicknessing table: Electric thicknessing table adjustment with fine adjustment, travel speed 10 mm/s, mounted on 4 support spindles to prevent tilting, finely planed table surface - Feed: 2 speeds 6 / 12 m/min, can also be selected electrically during planing, large rubber feed rollers Ø 85 mm to compensate for different thicknesses of wood, rubber rollers are gentle on the material and self-cleaning, easy roller change; link pressure beam at infeed - Suction system: Swivel-up, split hood with chip extraction nozzle Ø 160 mm, can be connected optionally on the left / right (in special cases on both sides); minimum extraction air volume: 27 m³/min. at 20 m/s - Maintenance device: Central lubrication strip for oil lubrication points; bearing / cutter shaft lubrication via nipple - Accessories: 1 grease gun, filled with long-life grease 1 oil gun 1 open-end wrench 1 tool for blade change 1 pair of blind knives 640 mm 2 pairs of TERSA reversible knives 640 mm CV - Emission values: Emission sound pressure level at the workplace LpA according to DIN EN ISO 11202 [dB(A)] Idle noise (without extraction) P1 65 Idle noise (w. extraction) P1 77 Operating noise (without extraction) P2 65 Operating noise (with extraction) P2 78 Sound power level LWA according to DIN EN ISO 3746 [dB(A)] Idle noise (without extraction) 84 Operating noise (with extraction) 90 Dust emission Low dust emission according to DGUV 209-044 / BGI 739-1 Location: ex stock 54634 Bitburg - immediately available -

Condition: good (used), functionality: fully functional, Technical details: SEW motor Type: DV132H8/4BH/HF/TH rpm: 700/1450 IP:54 Hz: 50 400V AC Hjdpfxjwu Dbbs Aaqsw Brake: 400V kg: 83.94 The SEW motor with rotary table is a powerful and versatile drive solution, ideally suited for precise positioning and automation tasks. The motor stands out due to its robust construction and reliable operation, ensuring stable and efficient performance. The integrated rotary table allows flexible and accurate control of movement sequences, making it particularly suitable for use in manufacturing and assembly applications.

Condition: new, Year of construction: 2025, Hebrock F 4 For complete processing of your panels For all those who don't want to do things by halves. With the F 4, we offer you a model with which you can produce fully processed edges on a machine length of just 4 m. The F 4 is not only space-saving, but also extremely attractive in terms of price-performance ratio. Max. Edge thickness 3 mm Min/Max. Workpiece thickness 8 - 50 mm Min. workpiece length approx. 160 mm Feed speed approx. 7 m/min. Ready for operation approx. 3.5 min. Max. Power consumption Ø approx. 7.4 kW Electrical connection 400 V - 3 Ph - 50 Hz Work table height approx. 900 mm Machine dimensions approx. 4050 x 1300 x 1400 mm (LxWxH) Weight approx. 820 kg Suction nozzle Ø 1 x 140 mm PLC control 10″ touchscreen Top-mounted rapid-heat adhesive container (maintenance-free) Support plate for edging material Automatic central lubrication (cross-cut saw, corner router) Visual display for workpiece sequence Extension arm (can be pulled out to the front) Interchangeable basin pre-equipment incl. adhesive changing device for PUR processing Surface scraper with dual tracing Pneumatic roller capping (scissor cut design, Hebrock system) Double roller top pressure (ball bearing) Hjdpfshqadcjx Aaqjw Transport chain with bolted special chain plates Jointing cutter Milling unit cross-cut saw Corner cutter Accessories: F4/09 Radius scraper (incl. pneumatic lift) F4/09/4 Multi radius scraper (R1/R2) F4/30 Pneumatic 3-point adjustment Location: From stock 54634 Bitburg - available at short notice -

Condition: new, Year of construction: 2025, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm Hsdpfxsw Sgnko Aaqsw - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice